Saw machete
This machete was designed and manufactured for camping use. HOW TO MAKE A MACHETE FROM A SAW. You will need it to chop branches, or cut out some bushes, tree branches, etc.
Let's start manufacturing.
Material:
1.Ancient wood saw.
2. Rope (2.5-3 m.).
Tool:
1.Bulgarian.
2.Ruler.
3.Pencils.
4. Sandpaper.
To begin with, I drew this simple drawing of the future machete, which everyone can make for themselves. Today I will show you how to make a real machete from a construction saw that can easily chop hard fruits. How to Make a Chopper from a Saw Video MEHANIKABIZ.RU. How to make a machete from a simple saw. HOW TO MAKE A MACHETE FROM A SAW. At this point I will clearly show you how to do this.
For example, the length of the handle should be the length of your eight fingers.
The width of the handle should correspond to the thickness of 2 fingers.
The length of the blade, from the tip to the beginning of the handle, should be the length of your clenched fist to your elbow.
The width from the beginning of the rounding to the tip should be 10 cm, the size of your palm.
At the end of the handle we make a protrusion like this, as in the photo.
Read also
And we begin to cut with a grinder according to our drawing, observing safety precautions.
In the end, we came up with something like this, almost similar to a machete.
From our workpiece we remove all the burrs along the entire contour, right down to the small protrusions.
How from old saw to make a machete/Do-it-yourself machete?
Now I’ll show you how to make it from an old one saws make a cool cool weapon. MACHETE? Enjoy your viewing everyone.
Like from the old one saws make a machete
A site that publishes the most interesting materials from all over the world. Tell me what can be made from an old Parma electric saw? The publication publishes.
I put a thicker disc on the grinder and cleaned the machete on one side and the other. This is best done using a grinding machine.
In the end, this is what should happen.
Let's move on almost to the main process, this. 6 comments on How to make a buggy from a Ural chainsaw engine is just right. DIY saw machete. SHARPENING. How to make one from a chainsaw. How from old saw make a machete » Never Home. You need to sharpen at an angle of 25 degrees, with one and other side. Good afternoon You need to make a machete from a saw. Actually pull down the triggers and make a handle. This is best done using a special machine.
Here's what I got. How to set teeth circular saw Often, for various reasons, we have to neglect the purchase of additional Supplies. Today I will show you how to make a cool bladed weapon from an old saw. In order to make a saw cut on a hacksaw, the essence of the saw cut is how to do it yourself. Don't judge strictly, I'm doing this for the first time.
You need to sharpen NOT all the way to the handle, but only after retreating 2 cm, as in the photo.
I took some fine sandpaper and finally polished our machete, almost to a shine. You can also polish it to an elegant shine on a special machine.
Read also
Somehow this is how it should work out.
As a handle, I use a small piece of cord, two meters long.
Here is the process of winding the cord around the handle. How to make a buggy from a chainsaw: 47 photos. First, let's fold it like this as in the photo, this one is needed to thicken the handle.
On the other side, we do the same thing; at the end of the handle, a loop like the one in the photo should form.
We begin to wind the cord, turn to turn, you can first moisten the cord itself, and when it dries it will seem to tighten.
When you have already wound the cord, we thread it through the loop and make one turn.
With which you can successfully fight your enemies. In fact, this knife serves quite peaceful purposes. For example, in Latin America, machetes are used to cut sugar cane or to make their way through impassable jungles. Machete - great thing for tourists and hunters. It is quite possible to make it yourself, if you have necessary tools and some skills.
For work you will need materials:
thin plate of hardened steel,
paracord - lightweight nylon rope with a core
a small piece of leather
leather rivet,
waxed thread or thin leather cord,
leather finishing wax,
chalk, container with water.
Required tools:
Bulgarian,
sandpaper,
knife sharpening tool,
awl, gypsy needle,
propane burner,
hammer.
Step 1. Scheme and pattern
Surely you have a suitable piece of hardened steel in your household. Draw a diagram of the future knife on thick paper. Cut out, and using the design as a template, transfer the design onto the steel plate using chalk. Don't forget to draw a handle.
Step 2. Preparing the machete
Using a grinder, cut out the workpiece. Do not neglect safety precautions - wear gloves and safety glasses. Pre-clamp the plate in a vice. Make a wide cut on the handle; it will be needed to form the handle of the machete.
Step 3. Sharpening
Now sharpen your knife. You can do this yourself by heating the blade with a propane heating pad and cooling it as needed in a container of cool water.
Step 4: Machete Handle
Make a handle. Wrap the handle tightly with paracord. Apply the turns of the cord, pulling it with force. Secure the ends of the cord well using a gypsy needle. If you have carpentry skills, you can make the handle wooden.
Step 5. Sewing the cover
The machete requires a sheath. For this you will need a piece of leather. Cut it out using a paper template, leaving a couple of centimeters for seams and hems. Try on the resulting workpiece. If everything is in order with the dimensions, make holes on the leather with an awl, at an equal distance from each other. Sew both parts of the cover together with leather cord or waxed thread.
Step 6. Clasp
Sew a short strap to the case for fastening. Attach two parts of one rivet to the strap and case.
A strap with a rivet will securely hold the machete in its sheath. WITH inside Sew a small rectangle of leather onto the case for greater convenience in wearing the sheath on the belt. To make the case last longer, sand the edges of the leather sections on it and treat it with special wax for leather. This is guaranteed to increase its service life.
Step 6. Final stage
In many films, the machete is demonstrated as a weapon that helps the main character defend against enemies or, conversely, attack them. In fact, this tool serves quite trivial agricultural needs. In Latin America, it is used to cut sugar cane or make their way through impenetrable jungles. In our latitudes, a machete can be used as a tool for woodworking. You can make a machete with your own hands. This will require you to have certain skills and the availability of the appropriate tool. The materials for making this knife are quite ordinary, you can find them without much effort.
Materials
Before starting work, prepare:
- a piece of thin hardened steel, maybe a little rusty;
- paracord;
- a piece of leather;
- leather rivet;
- gypsy needle or awl;
- waxed thread;
- leather finishing wax;
- sandpaper;
- grinder;
- knife sharpening tool;
- propane torch;
- hammer;
- container with water.
You can find a piece of hardened steel anywhere, you just need to look carefully. IN in this case To create the machete, a rectangular piece of steel found near the railroad tracks was used.
Step 1. Using chalk, draw the characteristic shape of a machete on a piece of steel. Don't forget to draw a handle.
Step 2. Cut out the blank for the machete using a grinder. Be sure to follow safety precautions. Do not wear loose clothing that may become tight, and protect your eyes and hands while working. For convenience when working with an angle grinder, clamp the piece of steel itself in a vice.
Don't forget to cut out the handle. Make it big, you will need it to form the handle of the machete.
Step 3. Sharpen your knife. To make it easier, you can give this workpiece to a blacksmith or do all the work yourself, heating the machete blade with a propane torch and immersing it in a container of cold water as needed.
Step 4. Wrap paracord around the handle of the machete. Place the twists of the cord tightly and tighten them firmly. Be sure to secure the paracord so that it does not unravel while working. Secure the ends of the paracord using a large needle.
It is necessary to wrap the handle of the machete. This will make it more convenient for you to work: the steel will not cut into your hand, and the machete will not slip out of it.
Step 5. Cut a case for a machete from a piece of leather. Repeat the shape of the blade, but remember to leave a few inches for seams and fit. Try on the resulting pattern. If everything is in order, use an awl to make holes in the leather. Try to make the intervals between them equal. Sew the parts of the cover together using waxed thread or leather cord.
Sew a small strap to the case. Attach parts of one rivet to the case and strap. The strap will allow the machete to be securely held in the case, and if necessary, by unfastening the rivet, you can easily take out the knife itself. WITH reverse side Sew a small rectangular piece of leather onto the cover. So, ready product It will be convenient to wear on a belt.
If you want to make yourself quality knife and you are stopped by the fact that there are no other similar tools in the workshop, take a closer look at these instructions. A craftsman makes a quality machete sword using only hand tool! During production, the author did not even use an electric drill; the holes were drilled with a hand drill!
The metal used to make the sword was 1050 grade; this is an excellent steel for making knives, common in America. Such steel is perfectly hardened, and this is very important in manufacturing. cutting tool, since otherwise the blade will not hold an edge. As for domestic analogues, this includes steel such as “50” and “50G”. To make a knife you will need steel with a high carbon content. Let's move on to the manufacturing process!
Materials and tools used
List of materials:
- steel 1050 ();
- thin boards (for linings);
- pins (brass, steel and others upon request).
List of tools:
- hacksaw for metal;
- wood saw;
- hammer;
- drill;
- metal files and rasps;
- chisel;
- burner;
- household or special oven (for annealing);
- hardening oil;
- sandpaper;
- epoxy adhesive;
- wood oil.
Machete making process:
Step one. Cutting out the primary profile
The author used 1050 steel as a blank; the metal can be bought in America without any problems. Domestic analogues are steel 50 and 50G. Draw the profile of the blade on the metal using a marker and start cutting.
The author clamps the workpiece in a vice and cuts out the primary profile using a regular hacksaw. Since the steel is not hardened, it cuts quite easily, the main thing is to be patient.
After this, we arm ourselves with a good file and grind off everything that we could not cut off with a saw. We carefully process the profile along the contour. The author removes with a file quite a large number of metal
Step two. Holes for pins
Next, you need to be sure to drill holes for the pins. How many there will be and what metal they will be made of, everyone decides for themselves. IN classic version It is customary to use brass rods, but steel is also suitable, even ordinary nails can be used. It is extremely important to drill holes before hardening, as it will be almost impossible to do this later. Hardened metal can only be drilled on a machine using a drill with a special tip.
Step three. Handle covers
Let's start making the overlays, here you will need two thin boards. Place them together and try to hold them in your hand; the handle should not be too thick. We attach the shank to the boards and outline it with a marker.
Now the overlays can be cut out! And since we only have hand tools in our assortment, given the lack hand jigsaw, we will cut it with a chisel! Make cuts around the handle profile where the material cannot be cut hand saw. Well, then take a chisel and cut off the interfering parts. Remove any remaining rough edges using a rasp.
Finally, all you have to do is drill holes for the pins and try to dry assemble the handle. If you wish, you can trim it on the sword with files.
Step four. Forming bevels
To form high-quality bevels, we mount the sword on a flat wooden block. Now take a metal file and start shaping cutting edge. First we make a bevel on one side, and then on the other. To be sure, you first need to mark everything on the blade to get the same angles. This is where all the main work with metal ends, next comes hardening.
Step five. Let's start hardening the steel!
The author did not use a furnace to temper the sword; it was enough for him gas burner. We move the burner gradually up and down to evenly heat the blade. Ideally, the steel is heated until the magnet is no longer attracted to it. The color of the metal should change from bright red to yellow, this corresponds to a temperature of 900-1000 degrees Celsius. Now we cool the blade in oil; mineral or vegetable oil will do; many people successfully use automotive oil.
If the steel is properly tempered, it will be so strong that a file will not take it.
Now comes the next one important stage strengthening the metal is its tempering. After hardening, the steel will be too brittle for the sword to be used for its intended purpose. Tempering allows you to give it spring properties. For this procedure, you will need an oven with a temperature of 250 degrees Celsius; heat the blade in it for an hour or two. Then you need to turn off the oven and let it cool with the blade closed. Vacation is done!
If you wish, you can sand the blade after hardening, but it looks much cooler with a dark patina. All that can be done is to sand the bevel area.
Step six. Glue the handle
To assemble the handle, you will need epoxy glue. Apply glue to the previously made pads and assemble the handle on the pins. In order for the glue to adhere well to the metal, it must be thoroughly cleaned with coarse sandpaper. After machining steel can also be wiped with acetone.
We hammer in the pins and tighten the handle well with clamps; it is advisable to use more clamps so that the handle sticks together well. The author decided to rivet the pins a little for reliability, but this is not necessary. Let the glue dry for 24 hours at room temperature, or better yet, more.
Step seven. Finishing pens
When the glue has dried, clamp the blade in a vice and begin processing the handle. First, you will need a rasp, with the help of which we form the main profile of the handle. Next, take a round file, it will be needed for bends and other hard to reach places. The handle must be aligned flush with the metal.