How to configure the zxv10 w300 modem. Raking paws: ADSL modem ZTE ZXV10 W300

Step #1.
Make sure the modem is properly connected to the computer. Open your browser (for example, Internet Explorer) and type http://192.168.1.1 in the browser's address bar (or click on this link). A page will appear asking you to enter your username and password. Enter the username “admin”, password “admin” and click the “Login” button.

Step #2.
After loading, the following window will appear.

Step #3.
Go to the "Tools" tab. Next, select "Update Gateway".

Step #4.
In the window that appears, in the “Select a File:” line, specify the following path to the configuration file d:\router\config. The configuration file is located on the attached
to the modem installation CD. It is assumed that "d:" corresponds to the name of the CD drive; if the name of your drive is different, you must
set it instead of "d:". Click the "Update Gateway" button. Wait while the settings load.

Step #6.
After rebooting, a page will appear asking you to enter your username and password. Enter the username “admin”, password “admin” and click the “Login” button.

Step #7.
Then select “Setup” from the menu, then “stream”.

Step #8.
In the “Username:” field, enter the username given to you instead of “guest@mtu”, and in the “Password:” field - the password. For guest access, use the login guest@mtu and the password mtu. Click "Submit". Then click on the “Save” button.

Step #9.
Then, for security reasons, you need to change the password to access the modem settings. To do this, go to the “Tools” tab. Next, select "User Management".

Step #10.
Enter a new password in the “Password:” and “Confirmed Password:” fields. Click the "Submit" button. After that, click the “Save” button. The next time you log in to the configuration page, enter your old login – admin and your new password.

ADSL modem ZTE ZXV10 W300 is an Internet access point and is intended for MGTS clients who want to receive this service using citywide telephone communications. This device is designed to connect to a wired and wireless network both at home and in small office spaces.

ZXV10 W300 has the following appearance:

on the front panel there are nine light indicators that notify you about the status of a particular function of the device;
on the rear panel there are four Ethernet ports, an ADSL port (connection to a telephone line), a power button, a button for quickly turning the Wi-Fi function on and off, a button to reset the device to factory settings, a power connector;
There is a USB 1.1 port on the side of the device

It has very small overall dimensions and a nice design.

Technical characteristics of the ZTE ZXV10 W300 modem

Basic data:

Device type - ADSL modem, Wi Fi router.
ADSL2+ standard support - yes.
Data encryption standards - WEP, WPA, WPA2.
There is a web configuration interface.

User interface:

WiFi ZXV10 W300:

data transfer standard - 802.11b and 802.11g;
maximum data transfer speed - up to 54 Mbit/s;
antenna - built-in non-removable.

Ethernet ports:

quantity - 4 pcs.;
connector marking - RJ-45;
data transfer speed - 10 / 100 Mbit/s;
standard - BaseT Ethernet.

number of ports - 1;
supported standard - 1.1

Connecting to a telephone line:

number of ports - 1;
connector standard - RJ-11.

Additional Information:

Overall dimensions - 190x130x35 mm.

Equipment:

modem ZTE ZXV10 W300 - 1;
patch cord RJ-11 - 2;
RJ-45 patch cord - 1;
ADSL splitter - 1;
power adapter;
technical documentation.

Instructions for setting up the ZTE ZXV10 W300 router

Before you begin setting up the wireless function of the ZXV10 W300 modem, you need to make changes to the TCP/IPv4 protocol on your computer. To do this, depending on the installed operating system, you need:

go to network connections, select “Local Area Connection” and right-click on the icon, call up the context menu, go to “Properties”;
in the settings screen that appears, select the required protocol type and click on the “Properties” button;
Next, you should check the box “Use the following IP address”;
set the values in the fields manually:
- IP address - 192.168.1.2;
- subnet mask - 255.255.255.0;
- main gateway - 192.168.1.1;
- preferred DNS server - 195.34.31.50;
- alternative (secondary) DNS server - 62.112.106.130;
When you have finished making changes, click on the “OK” button.

Now you can proceed directly to setting up wireless access. To do this you need:

to check the correct connection of the connecting cord (patch cord) of the ZTE ZXV10 W300 modem to your computer or laptop;
determine whether the power is turned on on the router;
in the address bar of any browser (for example, Opera) enter the value 192.168.1.1;
in the page that opens on the screen, enter the login and password of the ZXV10 W300 in the request fields (the default value is admin).

After the system verifies the correctness of the data, your browser will open the main settings window (after each change made, do not forget to confirm it by clicking on the “Submit” button). To set up wireless network access you need to:

At the top of the screen, go to the “Wireless” tab.
In the “Setup” item of the sidebar, check the “Enable AP” field, and in the “Primary SSID” field give the name of your network.
In the “Multiple SSID” tab, set the network visibility by checking the “Enable Multiple SSID” field.
To configure security, you need to go to the “Security” tab. Here you can select one of the methods presented by the manufacturer to protect the network from unauthorized access (WPA standard is recommended). At the bottom of the screen, check the “PSK String” box, and in the “String” field, enter the access code (it must contain upper and lower case letters, numbers, and be at least 8 characters long).

After making all changes, click on the “Restart AP” button.

The process of setting up Wi-Fi on the router is complete. Now all that remains is to disconnect the patch cord, open the list of available wireless networks and connect to your ZTE ZXV10 W300 router by entering the access code.

12/1/2011. Modem for sale, its price is 2400 rubles, the price includes home delivery, connection to the router of 1 PC via LAN + 1 laptop via WI-FI with subsequent configuration for the Internet provider Stream or MGTS. There is also the option to make your purchase cheaper if you don't need delivery and installation services. You can purchase a modem on the day of order! Check with our managers for the exact price and availability!

DSL N12u Wi-Fi 300 mbit MIMO +IPTV +EzQos Price 4400 rub*

*The price includes delivery, installation and configuration of the router on two computers/laptops.

An updated wireless router from the Chinese corporation ZTE has replaced the ZXDSL 531b modem. The router’s 100% compatibility with Stream-Tv technology is beyond doubt, since this modem is recommended by Stream as a replacement for the 531 b model. Also, the ADSL router can work with other ADSL providers like Domolink, MGTS. . Note about working in Beeline / Corbina networks. Although the router supports the mode of reassigning the WAN port to LAN 4, the device will NOT work with Beeline and similar providers, since it does not know how to be a PPTP, L2TP client. Working in ethernet routing mode is only possible with Internet providers without VPN connections (On Lime Provider, Acado Internet, Moscow City Qwerty Network.)

Technologies supported by the W300 wireless router

The W300 wireless router, which supports the modern ADSL2+ standard (speed up to 24 Mbit), not counting the traditional 4 x 10/100 LAN ports, embodies all modern technologies such as advanced QoS, firewall, various options for protecting the WIFI segment (WPA2, authorization via Radius, lists access by MAC addresses, etc.). A design feature of the ZX V10 modem is the absence of an external wireless antenna, although the wireless coverage area of the router is even better than that of its predecessor (ZTI 531 B), which we confirmed experimentally. The ultra-modern Zx Spectrum processor integrated into the device with a clock frequency of 300 megahertz will provide unprecedented routing performance along with powerful anti-hacker protection for a home network of 5-10 PCs.

purchasing a 2640 u router is an ideal solution for Strim and Internet from the Moscow City Telephone Network!
The Zixel P660HTW2 router is guaranteed to work with the STREAM provider, Mgts!
Router TpLink Tl-wr 340 Gd - reliability and durability at a reasonable price.

Service from setup wizards - for Wi-Fi routers (Moscow)

If the Wi-Fi setup instructions included with the ZXV10 did not help you, then call our technicians, they will quickly come to your home to set up the W 300 for Internet services, IP-TV via Wi-Fi via STREAM of two or more computers, laptops, smartphones.

Internet access from MTS, Dom.ru and MGTS providers is provided via a telephone cord. ADSL technology is used, and the provider can provide a suitable modem/router. In such cases, under MTS Internet, setting up a router is simply setting a login with a password. The bad thing is that you cannot connect a device issued by your provider to an Ethernet line, and you cannot use anything other than PPPoE. We'll talk about setting up one of these routers, ZTE ZXV10 W300, next.

So, the ZTE W300 device, manufactured by MTS, is equipped with proprietary firmware designed for ADSL connection. There can be only one Internet connection protocol - “PPPoE + dynamic IP address”. Before setting up, you only need to find out one thing: what is the address of the DNS server that works on the provider’s side. The numbers for this address are set in the network card settings. Now we will look at everything in more detail.

Connect the router, open the web interface

The device called “ZTE W300” has its own DHCP server, which is enabled by default. But still, in the network card parameters, set a static IP equal to 192.168.1.2:

Setting up a wired PC connection

The address of the router itself, as you might guess, is 192.168.1.1. This value is set as the gateway as well as the DNS server (first). The second DNS server could be: 195.34.32.116. However, different regions use different meanings, please pay attention to this.

If the network card is configured, any LAN port of the router is connected to the PC using a patch cord. A telephone cable must be connected to the ADSL socket. And lastly, connect the power supply. Wait a minute, open a browser on your computer and go to the router address (192.168.1.1):

Web interface ZTE W300 MTS

The password for the web interface is the word admin, the login is the same.

Setting up the Internet and local area

First of all, having entered the web interface, it is better to immediately go to the following tab:

“Application” page –> “FON Setting”

It is located in the “Application” section and is responsible for the “FON” option (distributing the Internet to other registered users). By turning off this option and then clicking “Submit”, you will protect yourself from overly intrusive “external” users connecting to the Internet from the street. But the provider assumes that you will not turn off anything (we will leave the choice to the owner of the modem).

Internet connection, quick setup

Go to the "Network" section. Here we need one tab containing ADSL port parameters:

"WAN Connection", initial state

On the tab shown in the example, you can create a new profile (you need to click “Create”). But it is recommended to use what the provider has already created: select “stream” in the top list.

“Stream” profile, MTS connection

Connection parameters are selected as follows:

Enable NAT – mandatory to enable;
Enable VLAN – not necessary;
VPI/VCI – 1/50 (specify from the text of the contract);
Encapsulation – LLC;
Service – UBR;
Subscriber login – see contract;
Password – also specified in the contract;
Authentication type – Auto;
Connection Trigger – Always On.

To save the settings, click “Modify”.

Basically, the connection is now set up and it should automatically become active after a minute (resulting in the "@" light turning on). If this does not happen, you need to look for an error in the password or login. Now let's look at how to set up IPTV. This is done simply:

Go to the “Port Binding” tab;
Select the “vod” option in the top list;
Specify the local port to which the TV will go;
Click "Submit";
Now select the value “m_cast” from the list;
Follow steps 3-4;
Select the value “stream” from the list;
You need to specify the ports not used for IPTV, then click “Submit”.

This completes the ADSL port setup. Check out the example.

IPTV sent to LAN1

Additional options important to the user

ICQ and Skype programs, as well as torrent clients, use an option such as UPnP. It needs to be enabled in the program itself, and in the router settings it is available on the following tab:

“Application” –> “UPnP” page

Just select the “stream” value in the top list, check the box and click “Submit”. Instead of using UPnP, sometimes port forwarding is configured. These two options are mutually exclusive.

Since the built-in DHCP server is already enabled, you can try setting the network cards to “auto IP”. DNS address values are still set “explicitly”, without turning on “automation”. Actually, everything should look like this:

Wired connection setup option

The parameters are set in the same way when connecting wireless devices (you need to set DNS). Happy routing!

Here we looked at how to set up a router that supports the FON and IPTV protocols.

There is a similar device called “W300 ZTE”, but it does not have such options. So, we are talking about different models of routers (with FON/IPTV - a newer version), and they are built on different chipsets. You need to remember this when choosing a firmware file to update.

Wireless network: turn on, configure

ADSL modem ZTE ZXV10 W300 is an access point to the global network and is intended for MGTS clients who want to receive this service through citywide telephone communications. ZTE ZXV10 W300 is designed for connecting to a wired and wireless network both at home and in small offices, setting up wi-fi ZTE ZXV10 W300

ADSL modem ZTE ZXV10 W300 is an online access point and is intended for MGTS clients who want to receive this service through citywide telephone communications. This device is designed to connect to a wired and wireless network both at home and in small offices.

ZXV10 W300 looks like this:

on the front panel there are nine light indicators that notify you about the status of a particular function of the device;
on the rear panel there are four Ethernet ports, an ADSL port (connection to a telephone line), a power button, a button for quickly turning the Wi-Fi function on and off, a button to reset the device to factory settings, a power connector;
There is a USB 1.1 port on the side of the device

It has very small overall dimensions and a nice design.

Technical characteristics of the ZTE ZXV10 W300 modem

Device type - ADSL modem, Wi Fi router.
ADSL2 standard support - yes.
Data encryption standards. WEP, WPA, WPA2.
There is a web configuration interface.

User interface:

WiFi ZXV10 W300:

data transfer standard - 802.11b and 802.11g;
maximum data transfer speed - up to 54 Mbit/s;
antenna - built-in non-removable.

quantity - 4 pcs.;
connector marking - RJ-45;
data transfer speed - 10 / 100 Mbit/s;
standard - BaseT Ethernet.

number of ports - 1;
supported standard - 1.1

Setting up ZTE ZXV10 W300 router mode (Promsvyaz M-200)

Read also

Forgetting a password is common. Especially if you don't have to enter it often. If you have forgotten your iCloud password, then you need to realize that you have forgotten your ID password. A hidden code from your Apple ID account is used for all Ap...

How to find out (see) Which iPhones, iPads, Macs are linked to Apple ID In order to fully use any device from the Apple company, you must have an Apple ID account and be linked to it. Next, let's talk about what options open after...

A few decades ago, only the wealthiest people could afford a color TV at home, but in the current situation, large plasma panels are commonplace. For a sophisticated TV viewer, several hundred channels and various...

3 proven ways to quickly turn on an alarm on your smartphone or tablet There are several ways to turn on an alarm on your Android phone, or rather on your smartphone or tablet. It depends a little on the device Samsung Galaxy, fly, Lenovo, xia...

There are rumors of a couple of new Canon cameras coming, the Canon 90D and the EOS M6 Mark II, and it seems like they can't stay secret any longer. both were leaked in seemingly official marketing videos. Raised by Canon Rumors, recently filmed videos from...

Here are the best iPad deals coming soon in December. great month for iPad deals. As the holidays approach, retailers are offering some of the best iPad deals of the year. From the compact iPad mini to the new 10.2-inch iPad,...

Settings to mode router ZTE ZXV10 W300(Promsvyaz M-200A)

Setting up the ZTE ZXV10 H208L modem

Settings modem ZTE ZXV10 H208L for Internet, wifi and IPTV. Control of a house lock ZTE ZXV10 H208L for the Internet, wifi

Connecting to a telephone line:

Additional Information:

Dimensions. 190x130x35 mm.

modem ZTE ZXV10 W300 - 1;
patch cord RJ-11 - 2;
RJ-45 patch cord - 1;
ADSL splitter - 1;
power adapter;
technical documentation.

Instructions for setting up the ZTE ZXV10 W300 router

go to network connections, select “Local Area Connection” and right-click on the icon, call up the context menu, go to “Properties”;
in the settings screen that appears, select the required protocol type and click on the “Properties” button;
Next, you should check the box “Use the following IP address”;
set the values in the fields manually:

IP address - 192.168.1.2;
subnet mask - 255.255.255.0;
main gateway - 192.168.1.1;
preferred DNS server - 195.34.31.50;
alternative (secondary) DNS server - 62.112.106.130;

When you have finished making changes, click on the “OK” button.

Read also

Samsung Galaxy A50. Specifications Dimensions: 74.7 x 158.5 x 7.7 mm Weight: 166 years SoC: Samsung Exynos October 7 9610 Processor: 4x 2.3 GHz ARM Cortex-A73, 4 x 1.7 GHz ARM Cortex-A53, Number of cores: 8GPU : ARM Mali-G72 MP3, Number of cores: 3RAM:...

“The MarQ Falkon Aerbook features a 13.3-inch display, is 16.5mm thick and weighs just 1.26kg” Flipkart-owned MarQ has launched a new laptop in the country. The Falkon Aerbook is the thin and light laptop that big brands want to conquer. MarQ with...

Huawei P30 Pro Powered by 7nm Kirin 980 SoCFeatures Huawei P30 Pro Spotted Running Android 9 Pie The upcoming smartphone may have four rear cameras. It has been confirmed to show the periscope style camera of the Huawei P30 Pro...

How to turn on the Internet on Android It’s hard to imagine a modern Android smartphone without Internet access. In this article we will talk about how to turn on the Internet on an Android smartphone via a mobile phone and Wi-Fi. How to turn on mobile Internet on An...

Apple has established itself as a high-quality company that annually continues to amuse its users with pleasant gifts, so in January of this year, the Lte network, also often referred to among people as ordinary 4...

How to Bypass Google Account Verification During DownloadAndroid development is one of Google's main goals. Among the many new features, we want to talk about the new security program that has appeared on all Android phones with version...

Now you can proceed directly to setting up wireless access. To do this you need:

to check the correct connection of the connecting cord (patch cord) of the ZTE ZXV10 W300 modem to your computer or laptop;
determine whether the power is turned on on the router;
in the address bar of any browser (for example, Opera) enter the value 192.168.1.1;
in the page that opens on the screen, enter the login and password of the ZXV10 W300 in the request fields (the default value is admin).

At the top of the screen, go to the “Wireless” tab.
In the “Setup” item of the sidebar, check the “Enable AP” field, and in the “Primary SSID” field give the name of your network.
In the “Multiple SSID” tab, set the network visibility by checking the “Enable Multiple SSID” field.
To configure security, you need to go to the “Security” tab. Here you can select one of the methods presented by the manufacturer to protect the network from unauthorized access (WPA standard is recommended). At the bottom of the screen, check the “PSK String” box, and in the “String” field, enter the access code (it must contain upper and lower case letters, numbers, and be at least 8 characters long).

After making all changes, click on the “Restart AP” button.

Post Views: 1