How to make a swan from a tire with your own hands. Swan made from tires: a master class for real men Swan made from a car tire

The swan is a beautiful bird that graces any pond. But not everyone can afford to purchase and care for real swans. But you can make your own artificial swan from scrap items.

This swan can be used to decorate a garden or playground.

You can also make a swan, into which you can pour soil and plant flowers. One way or another, both you and the children will receive aesthetic pleasure from such a craft.

How to make a swan from a tire





1. Prepare old tires, preferably “bald” ones, and mark the cut lines with chalk.

2. Start cutting along the lines, then bend them to create wings.









3. In order for the head and neck with the chest of the swans to keep their shape, it is advisable to use a stainless steel plate, which must be bent so as to give the shape of the head, neck and chest.









4. After this, you need to screw the plate to the rubber using inconspicuous small screws.

5. Also cut out the eyes from rubber and, using the same screws, attach them to the swan's head. And after that, cover our swans twice with white water-based paint, only make their noses red.









6. All that remains is to fix the swan in the halves of the lids, pre-painted in the color of the water (blue, light blue, green), and your swan floats in the pond.

How to make a swan from a wheel









This is another option for making a swan with your own hands from a tire. To make it, prepare, as always, an old wheel, chalk, a sharp knife (just in case, also have a hacksaw or jigsaw) and paint.

1. Using chalk, draw on both sides of the wheel all the details of the future swan, i.e. head, tail, wings, neck, beak.

2. Start with a sharp knife to cut out all the details along the contour lines.

* If some parts do not lend themselves, you can use a hacksaw or jigsaw.

3. Bend the wings and neck. If the neck is difficult to bend, plywood will help you, with which you can fix it.

4. All that remains is to paint the swan.

How to make a swan (video)

Watch the video tutorial on how to make a swan from a tire if you want to understand some of the details. This tutorial used a jigsaw.






How to make a swan from a tire









1. The first thing to do is use chalk to mark the areas on the tire that you will be cutting. The images show these lines.

* If your knife is sharp enough, then everything will take you no more than 20 minutes.

* It is worth noting that it is very difficult to cut thick rubber, so use a sharp knife that is periodically moistened with soapy water.









2. The hardest part of the tire must be knocked out using a chisel or grinder. This part will serve as the head and tail of your “swan”. Everything will take no more than five minutes.









3. It's time to turn the tire out.

4. It is advisable to properly treat the head and tail of the rubber swan, since uneven edges can cause scratches.

5. All that remains is to paint the swan - you can use white or a very unusual and beautiful bronze color.

How to make a swan from modules







Crafts from plastic bottles. Swan.









There is no need to get rid of plastic bottles if they have already been used for their intended purpose. There are many crafts that you can make from them.

For example, there are several ways to make a beautiful swan for the garden. Moreover, such a swan will not only decorate your garden, but will also bring benefits.

You will need:

Plastic bottle 5 l

Milk bottles 300 g

Hard Wire Hose

Wire

Scissors

1. Using a marker, mark the lines on the 5-liter plastic bottle that you will follow to cut out.









2. First cut off the top of the bottle and leave the neck, which is needed to secure the swan's neck in the hole.









3. For the skeleton of the swan's neck, use a hose with stiff wire. Insert it into the bottle through the neck and secure the neck to the lower part of the body with wire. You have a swan frame ready.











4. Preparing feathers for the bird. Take a white plastic bottle (usually the kind used for milk) and cut off the neck and bottom.









Start cutting the “feathers” - their width and shape depend only on your imagination.









It is advisable to cut the edges of the “feathers” with fringe to achieve an even more realistic effect.









Heat each feather of the candles from the outside.









5. Start collecting two feathers at a time and secure them with wire.









6. For the bird's neck, use bottles without a bottom. Depending on their number, you can choose the length of the neck. In this example, 16 300g bottles were used.

The part near the beak was made from the top of a bottle without a neck.

7. Where the beak is located, the hose ends and to attach the structure you need to make holes on both sides in the bottle and in the hose. Next, secure it with wire.









8. Close the lid and take a chemical cap to prepare the base of the beak. This cap needs to be cut in half, similar to the letter M.

9. Take another such lid and insert the beak into it - there is a groove inside so that everything comes out exactly.

10. Glue the first and second covers.









11. Paint the beak and place your favorite plants in the flowerbed.

How to make a swan from plastic bottles









This is not just a swan - this is a swan princess who will decorate any garden. It’s worth noting right away that assembling this swan is a labor-intensive and rather lengthy process, so be patient and let’s get started.

You can call on one or more people to help you create the craft to speed up the process.

Prepare:

Plastic bottles

Thick copper wire (if you have thin wire, fold it in half to prevent it from breaking)

Stationery knife

Pliers

White and yellow paint (can be regular or aerosol)

1. You should start making a swan from plastic bottles from the head and neck. Then these parts of the swan become the body. First, cut the plastic bottle to fit the head.









2. Trim the neck parts of the craft. It is advisable to make 18 similar blanks in advance to create a neck.









3. Use an awl to pierce each piece.









4. Prepare the wire and thread it through the holes of the blanks, gradually stringing them to form a neck (you need to thread it from the bottom to the head). Attach your wire to the tip of the beak.









5. When you have assembled all the pieces on the wire (1 piece for the head and 18 for the neck), start assembling the body. Prepare 4 bottles and cut them as shown in the image:









6. Using the same pattern, start stringing the pieces onto the wire. Insert a whole bottle into the outer blank.

7. Secure the other end of the wire.

8. To make a swan's neck stronger, you must first give it the desired shape. To do this, simply adjust the depth of entry of one workpiece into another.

Use wire to secure all the swan parts together.

Start making holes in the bottles that make up the neck so that the wire runs parallel to the floor (you need to do this on the floor and preferably start from the tail).









You should end up with a kind of “zigzag” of wire - it should “enter” and “come out” of the neck where the two pieces fit into each other.

9. Place the uppermost end of the wire where the crown is attached.









10. Cut out a crown for the swan princess from a plastic bottle.

11. Take the crown and place it on your swan's head. To do this, you need to make 2 holes in the neck of the crown and thread the wire from the neck into them. Next, you need to wrap the wire around the neck and use pliers to clamp it.









12. It's time to assemble the body. The first thing you need to do is the belly, which has two “sticks” and each of them is made by connecting 4 large blanks (point 4) and 1 whole plastic bottle.









You need to "sew" these "sticks" using wire. This should be done in a zigzag, parallel to the floor. It is necessary to create a rigid foundation for the swan.

13. We continue to make the body, namely its next row. The middle will be occupied by the swan’s neck, which means you will need the help of another person - while you “stitch” the second row, your assistant needs to keep the neck constantly in an upright position.









Still, first you need to prepare 2 “sticks”, each assembled from five large blanks and one whole bottle (for the tail). After this, all 3 blanks need to be fastened with wire, placing the neck between two “sticks”.









14. Pay close attention to securing the neck curve at the front.









15. We are preparing the third row of the body. Start assembling another “stick” - use 4 large blanks and 1 whole bottle for the tail.











Push your pieces tightly into each other, and pour water into the untouched bottle to balance the neck and tail of the craft.

It is worth noting that the stick does not need to be stitched separately. All you need to do is place it on top of the neck from the side of the body and attach it with wire to the side “sticks” of the 2nd row of the swan’s body.

16. It's time to make wings for your swan. To do this, you need to collect 2 “sticks”, each of which contains 4 large blanks and one whole bottle. Bend the pieces as shown in the image and fasten them again with a zigzag using wire.









To make the base of the wings you need to make 2 short “sticks”, each of which consists of one whole bottle and one large blank.

17. Begin attaching the bases of the wings to the swan's body. The image shows a top view with the bird's tail on the right side. To attach everything, use a wire that needs to be threaded through the bases of the wings and secured to the already installed swan parts.







22. It's time to paint. To do this, you can use either aerosol paint or regular paint (but it will take more time). If you decide to use an aerosol, then you need to paint outdoors, not indoors.









How to make a swan with your own hands









In this master class you will learn how to make a beautiful flower bed from the swan you made earlier.

You will need:

Plastic bottles

Plastic bags (preferably thick ones, for example, from washing powder or dry pet food)

Stapler

Saw or knife

Pliers

Scissors

Soil (preferably special ready-made soil from bags).

1. First you need to firmly secure the swan in a place specially prepared for it. To do this, you need to dig a shallow hole.









To keep the swan level, you need to hammer 2 wooden pegs on both sides of it, in the upper part of which you need to make small cuts.

Pull a wire through the notches, which will help the craft remain level.









The wire is threaded, tightened and secured under the curved parts of the wings.

2. Prepare one thick bag and cut it to form a large rectangle.









Cover the inner space between the wings with this polyethylene “blanket”.

*The edges of your bag should extend slightly above the wings.

3. You have a kind of pot into which you need to pour soil for flowers.









4. Use a stapler to staple the front and back of the flower bed together.









*If desired, you can cut off the excess edges of the polyethylene.









5. Now all that remains is to plant something in the finished flowerbed.

How to make a swan out of paper






How to make an origami swan

Very often, car enthusiasts end up with used parts, in particular from wheels. In this article we will look at how to make a swan from a tire so that it becomes a worthy decoration for your yard or garden plot.

How to make a swan from a tire using additional materials at hand

Your work will be most interesting if you use something else besides tires. So, your swan will become more voluminous if you add improvised feathers to it. Let's look at how to make a creation like the one in the photo:

To work you will need:

• Car tire;
• Wing mesh;
• Vacuum cleaner hose;
• Plastic bottles (white);
• Neck wire;
• Foam for heads;
• Sharp knife;
• The wire is thick and thin;
• Drill.

Step-by-step instructions for performing a swan:

1. Cut off the inner ring of the tire.
2. We cut out the future tail with a jigsaw or with a knife.
3. For convenience, we connect the parts with bolts and cut them in front.
4. Now you need to install the base for the neck. To do this, we make holes with a drill and use wire to fasten a thick iron rod to the tire.
5. We cut out the required piece from the mesh so that it covers the gap in the tire. We make two such preparations.
6. Screw the feathers on from the bottom. In this case, we cut out the feathers in advance from white plastic bottles, of which you will need about 70 pieces. Feathers may be the same or slightly different in length.
7. We assemble the wings so that there are no gaps in the mesh.
8. Cut out the head from foam plastic.
9. We put a hose from a vacuum cleaner of the required length onto the neck pin, securing it with wire.
10. We screw the head to the neck with screws, it is advisable to lubricate the fasteners with glue.
11. We paint our swan white and draw its face.
12. The last detail left is to screw the wings onto the screws, additionally tightening them from the inside with wire through the tires.
13. Your swan is ready, you can place it on the ground or on a post, as you wish.

Thus, with the help of simple steps you will make a very beautiful swan with your own hands, which will perfectly decorate your yard.

We offer a second, simpler master class on making a swan. It won't have any feathers, but it will still be very cute if done correctly according to the instructions.

For work you will need:

• Car tire;
• Screws and bolts for fastening parts;
• Fishing line and wire;
• Dye;
• Knife or jigsaw.

Instructions for performing the work:

1. In order for your swan to really turn out not to be an ugly duckling, maintaining symmetry is very important. Therefore, first take chalk and a ruler and draw out all the parts that you will cut out.
2. Draw the tail, head and for the wings cut the tire lengthwise into 2 strips.
3. A jigsaw is best suited for cutting; if you don’t have one, a well-sharpened knife will also work.
4. It is better to cut the parts in parallel to avoid unnecessary vibration.
5. It is necessary to treat the cord after cutting. You can use a hacksaw for metal.
6. You can make a swan either by turning the tire inside out or leaving it in the same state. The right side lower will lower the wings of the bird, and the wrong side will give more strength and raise the work.
7. The neck and head must be secured with thick wire. To do this, use a drill or awl to make parallel holes along the entire length of the neck so that a thin wire can be passed through them. And with its help, tie the rod, bending it in the shape of the neck.
8. Now paint the workpiece with permanent paint and draw the face.
9. Your work is ready, you can install it wherever you want.

You can even place the finished swan in the water, pretending that it is swimming on the water. Or you can use a pre-prepared diagram to facilitate the work process, for example, this one:

You can figure out how to cut and assemble a swan or some other animal from a tire for your garden plot.

The easiest option is to use old tires as a flower bed. You can simply paint them the color you want, or you can also make a swan. To do this, you also first draw with chalk the lines along which you will make the cuts, only in this case, you use only part for cutting out the details, the second is left for the flower bed. The bird's heads are secured in the same way, using a rod, as discussed in the master class. As a result, you will get a very neat, “living” flower bed.

Video on the topic of the article

To make your work easier, we have prepared visual material. We offer you to watch several video lessons and master classes on making this beautiful bird. Your swan, if the work is carried out correctly, even one made from a used tire will literally “come to life” before your eyes. Enjoy watching.

Back then they made it from a plastic bottle and putty. Today is a new post - we will make a swan from a tire. I think that many have already seen such swans in garden plots or playgrounds, but they don’t yet know how to make them.

Old car tires that have served their purpose often find a second life, becoming interesting and unusual crafts for the garden. Making an unusual shape from a tire is quite simple. And this decoration of your garden will serve faithfully for a very long time. All you need is to show a little imagination and spend about an hour of time.

The tire swan is a beautiful and unusual bird for your garden. To make a swan, you will need a car tire, screws and bolts for fastening the parts, attaching the swan to the base, fishing line and wire, and paint.

When making a swan, maintaining symmetry is of great importance. Therefore, before you begin the actual production of the craft, you need to carefully measure and mark everything. For this you will need a ruler and chalk.

It is most convenient to cut marked tires with a well-sharpened knife or an electric jigsaw, and to saw through the cord with a hacksaw. Instead of a hacksaw, you can use wire cutters.

You can make a swan from both the front and back of a tire. The reverse side allows you to make the craft smooth and even, and also gives the product greater strength due to bends. To make a craft from the wrong side of a tire, you just need to turn it inside out (you can’t do without male power).

If, when making a craft, some elements do not want to hold their shape, then you can secure them with aluminum wire or using stretchers made of transparent fishing line.

To make a swan, you need to form its neck, head and tail by carefully cutting the upper part of a tire placed on its side. In this case, the sides should also be carefully cut out - these will be the wings and back of the swan. The longer part of the resulting strip is cut out in the form of a beak and bent like the neck of a swan, and the short part is given the shape of a tail. The side round parts of the tire are divided along the circumference into two parts: the inner part is thin, the outer part is wider. The outer parts are lowered to the ground and fixed - these are the wings. The inner parts of the tire sides are brought together in the middle of the tire and fastened. It turns out to be the back of a swan. The craft is ready. All that remains is to paint it the desired color.

And this is a real pond with swans:

But let's not stop there either. After all, you can make not only swans from tires, but many other beautiful, funny and useful things.

You can decorate your garden without purchasing sculptures in a store using improvised materials, as many experienced and thrifty gardeners do. Some use plastic bottles, others use old clothes and objects, and others use wheels. One of the most popular figures made from tires is the swan. It’s easy to make a swan from a tire with your own hands, you just need to know a few important points.

The product requires a tire that has already been used; such material will be softer and more pliable. The cord on the tire is cut due to its rigidity. It is better to choose a wheel from a domestic car. Before use, wash with soapy water and dry.

You can make a swan from tires in several ways, as well as supplement them. Usually a cut-out version is used, not separating parts of the tire, but completely turning out and strengthening the bird’s neck. But many gardeners, wanting to have not only a beautiful decoration on their site, but also a functional one, use lighter options, leaving most of the tire free for planting. It will take from one to two hours to make any of the options.

Here are some things to consider before making a tire swan:

1. When making products, especially if electrical appliances are used, you should follow safety precautions, and also wear gloves and goggles to prevent pieces of material from getting into your eyes.
2. The product is cut out in the open air, because when using a grinder and a jigsaw, there will be a lot of smoke and an unpleasant odor coming from the tire.
3. It is better to cut the cord - this is the inner part of the tire that holds the entire structure tightly. If you don't cut it off, it will be more difficult to make a bird.
4. The tire must be of old production, they are softer, without spikes and additional metal structures, additional metal reinforcement on the cord.
5. To make cutting easier, it is better to choose a tire with a tread that roughly matches the pattern, for example, in the form of rectangles.
6. When the neck of a bird is cut out, you can install a block under it that will help support it, and it will be more convenient to cut it off. An old tree stump can serve as a similar support. It is better to start the cutting process from the base of the neck to the nose, and then continue cutting out the neck.
7. After making the bird, it is better to install it on another tire or dig a shallow groove under it so that it has stability.
8. The paint for the animal is chosen to be resistant to weather changes. For example: for facades or enamel, automotive spray paint, forge.
9. If the tire had metal cord reinforcement, then the edges of the product must be processed with a grinder so that the sharp edges do not cause bodily harm (cuts) in the future.
10. It is better to apply the paint in 2-3 layers, after each time allowing the previous layer to dry thoroughly, then such decoration will not need to be processed for 3-4 years.

Schemes, drawings of swans made from tires:

Tools and materials

To make it you will need:

• chalk or marker;
• tire – per bird – 1 pc.;
• paint – white or black, for the beak red or any other;
• plywood for the nose, if making a bird from the second option;
• jigsaw;
• screw and nut, rivets, self-tapping screws - any material that will help fasten 2 parts of the tire;
• Bulgarian;
• pliers;
• drill;
• wire staples or clamps;
• wire - rod;
• roulette;
• knife, just not a kitchen knife.

Video on how to cut a swan from a tire:

Option 1

Step-by-step instructions on how to make a swan from a car tire:

1. On the tire, draw the outlines of the bird with chalk (or a marker in a contrasting color).
2. The wheel is visually divided into 2 equal parts, one is the neck and head, the other is the body, in this proportion the bird will have a more aesthetic appearance.
3. The marking should occupy the entire part of the wheel so that the bird’s nose rests against the pattern of the tail.
4. The width of the neck is 7-10 cm, the head is 10-14 cm. The neck needs to be widened by 1-2 cm towards the body.
5. The tail is drawn in the form of 2 triangles or one large one and 2 small ones on the sides.
6. When marking the body, not only even strokes are used, but can also be done in the form of small wavy or zigzag lines.
7. After the prepared drawing, take a jigsaw or a sharp thick knife (for example, such as for bear hunting).
8. Exactly following the drawing, start cutting out the swan from the head. To do this, you need to puncture the tire in the nose area.
9. You need to cut in parallel, moving gradually a few cm on one side, then on the other.
10. After the bird has been cut out, the tire should be turned out. It is better to do this together with an assistant, but you can do it on your own. Then you should place the inside of the bird’s neck and head on the ground and place your feet on one of the wings. Push the middle of the tire down to the ground as much as possible, using your feet to press down.
11. After you succeed in pushing through the middle, the bird will acquire a certain outline of the body with wings, after which the head needs to be secured.
12. From the head to the tail, you need to make parallel holes with a drill so that you can attach a reinforcement rod that will support the head and neck.
13. Insert staples made of thick wire into the finished holes.
14. Prepare a rod - from wire rod, about 6 mm, bend it in a semi-arc.
15. Apply from tail to head and secure with staples.

When everything is secured, the head can be turned around and turned into the desired position, and then proceed to decorating.

Option 2

How to make a flowerbed swan from a wheel:

1. Clean the tire and apply the design; it should be applied to only one side of the tire.
2. From one edge we draw a heart shape, where a triangle should be left at the cut site. The drawing itself should occupy more than 3 parts of the side.
3. Use a knife to make a cut according to the markings.
4. You need to make several holes along the edge of the tire, and after cutting out the semicircle, make cuts to make it easier to turn the tire out.
5. When the semicircle is cut out, it needs to be turned out, and the rest of the tire.
6. Fold the semicircle - this will be the neck, fasten the 2 halves of which with a screw and nut.
7. Cut a triangle out of plywood to represent the bird’s beak and attach it to the neck using self-tapping screws.

The flowerbed is ready, all that remains is to paint and add soil so that the plants can be planted.

Any carved bird can be used to make a flower bed. For example, if you cut a swan according to the first option, it is placed on a larger tire into which soil is poured, and the bird is slightly buried in it. A small layer of earth is also poured into the lower part of the body, as if comparing the level of the embankment.

Creeping or low-growing plants are planted in such a structure; those that bloom with blue flowers, depicting the surface of the water, look the most beautiful: periwinkle, creeping thyme, awl-shaped phlox, speedwell, ivy. And if you install it on a hill, you can use hanging plants for decoration: petunia, begonia, campsis, dichondra, lobelia.

Usually, when making one bird, craftsmen also make a second one, because, as you know, a swan is a paired bird, a symbol of family and fidelity. Therefore, it will be beautiful to place a whole family of birds on the site or make a sandbox for a baby.

Master class on how to make a swan out of a car tire with your own hands:

Swans made from car tires are a decoration for many gardens and summer cottages. Simple crafts made from old tires even belong to a certain direction of creativity called trash art (literally - “art made from garbage, unnecessary rubbish”). Resourceful gardeners and summer residents have been making such birds since Soviet times, so we can say that there are work techniques that will ultimately help you get a beautiful and high-quality craft. If you are wondering how to make a tire swan, please follow us!

Well, let's get down to business. How to make a swan from a tire with your own hands? First of all, we will prepare everything necessary for creativity:

• An old tire (or several old tires if you want to decorate your garden with a whole bunch).
• Jigsaw or grinder (angle grinder).
• Electric drill.
• Pliers, wire cutters.
• Technical knife.
• Chalk, marker for marking.
• Metal rod.
• Paint for the future animal.

Choosing tires

To get beautiful and durable swans from tires, the first thing you need to do is choose the right material for the job. So, what will be most useful to us:

• Old tires from passenger cars. In this case, the emphasis is placed precisely on their age and wear - the tires must be worn to the limit. Motorists also call such tires “bald”. In a word, the more hopeless the material is for the driver, the better it is for our tire swan (we will discuss in detail how to make a garden decoration later).
• But imported tires, especially studded ones, will not be so good for crafts.
• The best option is rubber with a nylon cord. You can simply cut it with a knife. But if the cord is metal, then there is no way to do it without special tools (we have listed them).

You don't have to be a car owner if you want to know how to make a swan out of a tire. You can go to a tire shop for the material - they will give you your used tires. Calculation: one swan = one tire. If you are not confident in your abilities and want to experiment, then you can take more tires.

The work is best done outdoors, in the same garden. Tires need to be prepared for the process - washed and dried thoroughly.

Now let’s move on to step-by-step instructions on how to make a swan from a tire.

Drawing

First of all, let's outline the outline of the future bird. How to make a swan from a tire at this stage:

1. Using chalk, divide the length of the tire into two halves.
2. The second step is to draw the neck, head and beak, focusing on the middle marking.
3. The length of the element from the base of the neck to the beak must be greater than 1/2 the circumference of the tire. For example, if the latter is 180 cm, then we need to measure at least 95 cm.
4. To make the head proportional, make its length 10 cm. The beak will then be 9 cm.

Cutting out the neck, head and beak

The instructions on how to make a swan from a tire continue with the next step - cutting out the figure. Here's what's important for us to consider:

1. We cut the tire along the contours of the head, neck and beak.
2. If we have an old-style tire (with a nylon cord), then we can handle it without any problems with just a technical knife. We recommend dipping the blade into a soapy solution from time to time to make your work easier.
3. If the tire has a metal cord, you will have to turn to a grinder. It is better to work with the grinding machine in the fresh air. Take care of your safety - closed shoes and clothing, and protective gloves are required.
4. If you are using a grinder, then one swan will require up to 3 grinding wheels - rubber increases their consumption well. This method of work is fast, but not environmentally friendly. Heated rubber will have a characteristic smell. We must not forget about soot and burning.
5. Following step-by-step instructions, you can also cut a swan from a tire using a jigsaw - working with this tool will be much more pleasant than using a grinder. But in this case, you need to make a hole in the tire to start the saw. You need a drill or chisel.
6. How to use a jigsaw? The wear of its blades will increase from working at high speeds. Therefore, it is optimal to reduce the latter below average, and also to use a file with a reverse tooth. And this is the optimal solution. The reverse tooth will tear the metal cord, and low speeds will not allow the rubber to heat up.
7. How to make a swan from a tire with your own hands using a mechanical (hand) tool? You can use a regular metal file. It can also handle iron cord, but the progress of the work will slow down and you will have to put in more effort.
8. We cut and saw the neck only along the intended contour - no transverse cuts are needed here!
9. Here, beginners make a big mistake, which makes their work much more difficult. They begin to cut out the neck completely on one side - right or left. This is not true. We act in small sections - we cut a little on the right, then the same amount on the left, etc.

Tail cutting

We continue to imagine how to make a swan from tires (step by step instructions):

1. The last cutting step is the tail. Its outline must also be pre-marked with a marker or chalk. The approximate length is about 25 cm. It is cut according to a similar pattern - we saw a little along the left contour, then the same amount along the right, etc.
2. The tail is not only a purely decorative element. He will help us cope with the next stage - turning the tire out. Thus, her transformation from an ugly duckling into a beautiful swan.

Turning the structure inside out

Now we have come to the most difficult and crucial moment in the story, telling you how to make a swan out of a tire step by step (look for photos with tips throughout the article).

The process of turning the figure inside out is quite labor-intensive - the tire is laid with the cut part down. Then it is pressed down with your foot and pulled in such a way as to turn the side parts up. The central area of ​​the figure is pressed down. This is how she now more or less looks like a swan.

Final works

We complete the transformation procedure from the ugly duckling:

1. Lower the resulting lateral semicircles down.
2. If you used tires with a metal cord, you will have to additionally process the edges with a grinder. However, this will not completely rid the bird of protruding reinforcement. Therefore, it is permissible to use such a swan to decorate garden or summer cottages, but not a children’s playground. But even in this case, you need to be careful - install the structure where you cannot accidentally touch the protruding reinforcement.
3. We continue to look at how to make swans from tires (the photo will help you navigate the sequence of work). The next step is to strengthen our bird's neck. To do this, paired holes are drilled opposite each other along its entire length every 15-20 cm. They are located strictly along the center line.
4. Staples made of soft thin wire are inserted into the holes made. In turn, a thick wire is attached to them. You need to cut off a skein of at least 1.5 m. We fix the lower part on the inside of the base of the neck, the upper part on the top of the head.

Composition design

That's almost all, our swan is almost ready. Left a little:

1. Bend his neck at the desired angle.
2. Eyes can be cut out from leftover rubber. They are screwed to the head with screws.
3. To make the appearance of feathers, make notches on the lower inner parts of the wings.
4. It is easy to make a swan princess from our composition by making a crown for a rubber bird from an ordinary plastic bottle.

Coloring the composition

To complete the image of the royal bird and make our creation more aesthetically pleasing, it needs to be painted. For rubber swans, they mainly choose white and black paint - to match the natural color of living birds in nature. But garden sculptures covered with gold or silver materials also look no worse. The main thing is that the paint you choose should be durable and intended for outdoor use.

For rubber, enamel, oil and nitro dyes are best suited. We will apply any paint only to a dry and clean surface! If you follow this rule, the color will easily and evenly decorate our swan. The paint will not crack or deform and will retain its attractive appearance for a long time.

If this is not enough for your aesthetic sense, you can turn to acrylic paints. With their help, it is easy to draw a beak, eyes, and a semblance of plumage.

Location of garden sculpture

So, our handsome swan is completely ready. Now all that’s left to do is decide where best to place it. Let's turn to zoology. The natural habitat of swans is water bodies. Therefore, our composition will look wonderful next to an artificial pond or fountain on your site. It is also possible, having thought through a suitable stand, to install it “floating” on the surface of this mini-reservoir. By the way, if you didn’t know, you can actually build an imitation of it from that car tire!

Tire swans look good as decorations on an evenly trimmed lawn. Many gardeners decorate their flower beds with birds. You can even paint the bird in a suitable shade to match the flowers that grow there.

Resourceful summer residents make an impromptu flowerbed out of the swan itself! To do this, the bird is placed on another car tire for stability, which can also be painted in a harmonious color. Suitable soil is poured inside it, seeds or seedlings are planted. The composition can be watered and fed, because the rubber is quite resistant to such influences. Imagine how great it will look that your swan seems to be floating out of a cloud of flowers!

It is a little troublesome, but very beautiful in the end, to make a special pond for homemade birds. To do this, a small pit is prepared, the bottom of which is covered with dense polyethylene (it is important to securely fix it with stones on the “shores”). Pebbles are poured into the bottom, and then the space is filled with water. To prevent water from stagnating, you can periodically take it for watering, and simply add fresh water in return.

Crafts from car tires

If you've enjoyed turning used bald tires into something truly beautiful, then we recommend looking no further than swans. As we have already said, you can build a flowerbed or mini-pond from tires.

If you have small children, then it’s a good idea to make a play corner for them on the site, decorating it with compositions from the same tires and scrap materials:

• From one tire and plastic bottles stuck into it, we make a sun, coloring it yellow and drawing a face.
• Tires stacked on top of each other can make not only a summer snowman, but also an Olympic bear and bunny. The main thing is to successfully paint the product.
• From an old tire, by attaching pieces of old rubber to it, you can get a cute fish.

But folk craftsmen do not stop at decoration. Comfortable and functional country furniture is made from tires! These are poufs, chairs, armchairs, tables and children's swings. It’s already a classic to use used tires as fencing.

So we looked in detail at how to make a handsome swan from car tires. Follow the instructions, experiment to decorate your site with real masterpieces!

If you have old tires lying around in your garage, don’t rush to throw them away. Of course, you can no longer drive with such tires, but you can use them to make interesting decorations for your yard and garden. For example, these could be figures of swans with outstretched wings.

What materials and tools are needed to make a swan from a tire?

It is very important to choose the “right” tire for the job. I recommend taking one that has become completely bald during use: it is easier to cut and process. For the same reason, it is better to take a tire with a longitudinal pattern. Another tip: it’s better to choose tires with a cord (a rubberized layer of fabric made of textile, polymer or metal threads) made of nylon, rather than with a steel cord reinforcement (breaker). Reinforced products are difficult to cut, and the edges of the cord may stick out at the cut site, which can injure you while working. Such tires have the word “Steel” in the marking, therefore it is not present in a tire with nylon reinforcement.

Carefully choose tires so that working with them is convenient and does not pose a risk of injury.

Wash and dry the selected tires thoroughly. In addition to them, you will need for work:

• chalk for marking;
• roulette;
• electric drill;
• drills 3 and 10 mm in diameter;
• sharp knife (with a powerful shoemaker-type blade);
• jigsaw;
• “grinder” with a cutting disc;
• pliers;
• wire for staples;
• a plastic metal rod (or thick wire) 1.2–1.5 meters long;
• paint to give the finished “swan” the desired color.

In addition, you need to draw a diagram according to which you will cut out the swan. You can use a very simple form to get a small flower bed.

You can make a small flowerbed in the shape of a swan using a simple pattern

When working with this scheme, it is enough to make cuts along the lines:

• head and neck;
• tail;
• feathers on the wings.

After this, you need to turn the tire inside out, attach the halves of the head to each other and place a beak made of a piece of plastic between them. Secure the shape with self-tapping screws and paint it in suitable colors. You will end up with a small round flower bed.

You can plant any low, densely growing flowers in a simple tire flower bed.

A little more complex in execution, but very beautiful, is the original figure-decoration in the form of a swan spreading its wings.

You can make a beautiful swan spreading its wings to decorate your garden

The process of creating a swan from a tire

First of all, you need to mark the tire with chalk. Let's take an R13 tire. Its width is 165 mm, length along the circumference line is 1800 mm.

Product marking

Mark the product as follows:

1. At the beginning of work, apply 2 stripes dividing the circumference of the tire in half lengthwise. This will outline the “neck” of the swan.
2. After this, draw a “beak”, “head” and “neck” in turn on the tread (outer) side of the tire. From the first line, draw a “beak” symmetrically to the axis with dimensions: length - 8–9 cm, width - 3–4 cm. It should go into the “head”, the parameters of which are as follows: 10–12 cm - length, 7–8 cm - width, from the end of this “part of the body” you need to mark the “neck”, expanding towards the body. Its width at the beginning is 4–5 cm, at the end – 8–10 cm.
3. Lastly, mark the “tail”. Its fork is located where the “beak” begins. Draw two parallel lines 8 cm apart and up to 30 cm long.

The process of creating a swan from a tire begins with marking the tire

Cutting process

Now start cutting:

1. Cut from the base of the “neck” towards the “head”. A shoe knife can probably handle a heavily worn tire, but a thicker tread (tire element) is best cut with a grinder. If you have a fairly powerful jigsaw, use it after making the initial holes with a grinder.
2. Carry out parallel cutting on both sides in small intervals of 4–5 cm. This is much more convenient than cutting out one side completely first, and then the other.
3. When the cutting is finished, process all the edges of the resulting parts. If there is a metal cord in the tread, cut off the protruding wires using a grinder. For nylon cord, finishing the edges with a sharp knife is sufficient.

Remember the safety rules! Be sure to wear gloves and use special glasses.

How to turn a tire out and bend the “neck”

To ensure that the cut tire takes the desired shape, turn it inside out. Dealing with this is not difficult. To make the task easier, use your foot to secure the tire on the outside of the rim. The frame is ready. Now you need to fix the neck and head. To do this, you will need a steel rod to which the “neck” piece will be attached. Do the following:

1. Along the center line from the middle of the “head” to the base of the “tail”, make paired holes with a drill. Their diameter should be 3 mm, the gaps between them should be 15 cm.
2. Prepare wire staples according to the number of pairs of holes. They will attach the “neck” to a metal rod. Immediately insert them into the holes.
3. Place the rod from below, using pliers to twist the protruding edges of the brackets around it. Trim off the excess and give the “neck” a characteristic bend.

Instead of a rod, you can use a steel strip. Some masters find it much more convenient. In this case, do not use staples, but bolts or rivets for connection.

The neck of a tire swan is fixed using a metal rod attached to the tire with wire staples

Decoration and installation

Check again to see if there are any sharp edges or protruding wires left on the swan figure. If there are any, clear them.

Paint the figure white or black, a color characteristic of swans. You can apply a different shade or completely cover the figure with fantasy patterns. It is important that the paint is resistant to wind and moisture. Make the beak red, and screw in large bolts where the eyes should be.

Tire swans can be an additional decoration or an independent decoration

A manufactured and decorated swan can be placed on a whole tire, stump, or simply on the ground, lightly sprinkled with soil for stability.

Using the same scheme, you can create another version of the swan figure. The tire does not need to be turned inside out; it is enough to bend the “wings” further so that they lower to the ground.

If you don’t turn the tire out, the swan figure will be even more original.

Photo gallery: swan figures made from tires and options for their arrangement

A family of black swans made from tires in a natural body of water looks very elegant. The swan can serve as a flowerbed. You can use your imagination and paint the swan in several colors.

For those people who appreciate beauty, there are many ways to decorate the space around them, be it a workplace, front garden, apartment or area in front of the house. For example, you can use old car tires as a small flower bed or to create different shapes. Very often you can see a swan or other animals made from old tires flaunting in front of the fence of a private house. A tire can serve as a flower bed - this use of old tires can be seen in the courtyards of high-rise buildings and on the playgrounds of kindergartens.

Tire swan: master class

Step-by-step instructions will help you make a swan from unnecessary tires, and even if you don’t succeed the first time, you don’t need to be upset: this is quite painstaking work. First you need to find a tire that will be the most comfortable to use. Any “bald” tire that has a longitudinal pattern is suitable for this task. It will cut better, and it will be easier to make the desired figure out of it. Before starting work, the tire should be washed and dried to make it easier to work with.

So, you need to draw chalk lines on the tire that will divide it in half, the lines should be parallel to each other. Using this action, the image of a swan's neck is created. After this, you need to draw a beak that will go from the first center line, its length should be no more than 9 cm. Next, the beak should go into the swan’s head, its length is about 12 cm, width up to 8 cm. Below the head, the neck begins, first it It is 5 cm wide, and closer to the body it expands to 10 cm.

The tail is made using two parallel lines, which are 8 cm wide and about 30 cm long. The fork of the tail is the result after cutting out the beak, so the tail is the easiest to make. After all the elements of the swan have been drawn, you need to move on to cutting; for this process you need to get gloves and glasses.

To cut out the swan, you can use a grinder if the tire is quite hard, but after all the main lines have been cut, it is better to use an electric jigsaw. It is better to move the grinder on two lines at once, making cuts of 5-6 cm on each of them, this will speed up the process and make it easier. If you cut one side first and then the other, the process will take longer. After all the elements are cut out, they need to be trimmed along the edges so that there are no sharp or torn areas.

In order for the swan to gain wings, the span of which is quite large, the tire must be turned inside out, for this it is necessary to apply the efforts of the legs and arms at the same time.

To strengthen the neck and head, you need to use a steel rod. To do this, you need to drill paired holes on the rubber along the center line, the distance between which will be at least 15 cm. You need to drill from head to tail, and then thread a soft wire into each hole. With its help, the rubber is attached to a metal rod, and the swan acquires a clear silhouette.

It is better to lay the rod starting from the bottom of the swan, thereby allowing the ends of the soft wire to be twisted around it. Once the neck is attached, it needs to be arched to achieve the curve of a real swan.

In principle, the swan figure is already ready, now you need to paint it, even if the swan is black. But before painting the swan, you need to inspect it for sharp or uneven elements so that neither children nor adults can get hurt.

Tire swan: decor options

The bird can be painted white or black, depending on the owner’s wishes. Be sure to highlight the beak with a bright color, such as red or orange. The main thing is that the paint used to paint the swan is durable, because it will always be outside.

You can also make eyes for the swan by painting the spots black, or using large nails for this. You can choose the color scheme at your discretion; it is not necessary to use white or black.

This scheme for making a rubber swan is considered the easiest, so you don’t have to look for other options. And for a visual explanation of each step, you can watch training videos and, following the example, make your own swan.

Also, the swan can be placed in different places, for example, near some flower or in the garden, in front of the yard or, directly, in the yard itself. You can use another whole tire or sand as a stand.

In any case, this way of decorating a yard will appeal to many: family members, children, and even animals.

What can be made from tires: video

For many Russians, a summer cottage is not only a place where vegetables and fruits grow, but also a relaxation area for soul and body. Decorative ponds, garden gnomes, flower beds, paths, etc. – there are a huge number of ways to decorate a vegetable garden. Recently, crafts made from waste, such as plastic bottles and old car tires, have become popular. There are many benefits to giving a second life to old items. Step-by-step instructions for learning how to cut a beautiful swan from a tire yourself will help you make such a craft!

• Firstly, it is environmentally friendly, because things will not rot in a landfill for centuries, polluting the environment.
• Secondly, it’s always nice to create coziness and decorations with your own hands.
• Thirdly, it is profitable; such decorations will require a minimum of financial investments, because every motorist’s tires wear out. You can come up with a lot of decorations for the garden from them: small flower beds, fences, artificial ponds and much more. Figures of animals and birds carved from tires are also gaining popularity. If you also decide to decorate your garden plot, read the master class.

How to cut a swan from a tire with step-by-step instructions

• Worn car tire
• Grinder saw
• Jigsaw
• Thick wire, rod or steel plate
• White and red paints for exterior use
• You should work outside, as the grinder heats up the rubber, and this gives off a strong burning smell
• Be sure to wear thick mittens or gloves
• Feet must be in closed shoes

We study safety precautions when cutting a shape from a tire

Let's get started - step-by-step instructions on how to cut a swan from an old wheel

For work, you need to choose the oldest tire, as thin as possible and, as they say, bald. The more worn the rubber is, the easier it will be to work with. If you have a choice, it is better to give preference to a tire with a nylon or nylon cord rather than a steel one. To do this, the tire itself should not have the “steel” marking. The latter are difficult to cut, and they are also dangerous both during operation and during further use: it is better not to place such a bird on the playground to avoid cuts in children.

First, you need to draw a “pattern” of the future swan on the tire. Mark a point in the middle and from there draw a beak that smoothly turns into the head and neck of the bird. When working with an R13 tire with a circumference of 1.8 m, the dimensions are approximately as follows: beak length 8-9 cm, head 9-10 long and 7-8 cm wide. The neck at the beginning has a width of 4-5 cm and is closer to the body thickens to 8-10 cm. Its length is about 75-80 centimeters.

The swan's body should remain undivided and should not be cut: this part is where the wings and neck are connected to the head.

Diagram for cutting a swan:

After completing the drawing of the swan from the wheel, the cutting process begins. It's quick to cut with a grinder, but this heats up the rubber and gives off a strong smell of burning and soot. Therefore, many craftsmen prefer to make notches for the jigsaw blade using the same grinder, drill or chisel, and continue cutting with it. It is convenient to use a blade with a reverse tooth at low speeds. This way the material will heat up less, there will be no soot, and control over the process is better due to the low speed of operation.

It would be correct not to cut out one side completely and then the other, but to make small cuts on both sides one after the other. It’s much more convenient to work this way, the rubber doesn’t bend as much, and the likelihood that it will turn out symmetrically increases.

Next, you need to unscrew the workpiece. It's not long, but it's quite hard physically. To do this, you need to lay it with the cut part to the ground, press it down with your foot and pull the resulting wings up. The result should look something like the photo.

After this, you should secure the shape of the neck. To do this, you need to make holes in it in pairs at a distance of 15 cm from each other and insert soft wire staples into them. Use them to attach a rod or steel plate to the bird's neck from above. Next, bend the part so that it resembles the neck of a swan.

After cutting and shaping the swan, all that remains is to install the figurine in the selected area and decorate it. It will be beautiful to make not just one bird, but a couple at once. Paint the body white and the beak red. Draw eyes or form them from buttons, stones, pieces of rubber.

You can also make a stand from another tire lying on its side. An artificial pond or its imitation, for example, made of stones, will look very useful.

In addition to the swan, you can make other crafts with your own hands from tires. All you need is a little imagination and time.

Video on the topic of the article

Swans have long chosen not only ponds and lakes; they are increasingly found on personal plots. On the green lawns you can see entire flocks of swans made from car tires. Designers called this trend trash art (from the English trash-art) - art that involves old trash.

The name is new, but the idea of ​​creating beauty from waste appeared a long time ago. Extraordinary miracle birds have decorated more than one yard or garden. If you like this kind of art, we suggest you get acquainted with the technology of making swans in more detail.

How to make a swan from a car tire

Beauty on the site can be made from scrap materials, but you need to understand that this is work, not pampering. In order for miracle tire swans to bloom in your garden, you will need:

• Old tires;
• Electric jigsaw or grinder (grinder);
• Electric drill;
• Nippers, pliers;
• Chalk for marking;
• Metal rod;
• Dye.

Which tires to choose

Old, well-worn passenger car tires are suitable for swans. Moreover, the rubber should be as worn out as possible, worn down to the limit. Such tires are called bald. The worse the material looks, the easier it is to work with. Do not take studded tires, especially imported ones.

If you have the opportunity to choose, it is better to take rubber with a nylon cord. Such material can be cut simply with a knife. Tires with metal cords are more difficult to process; in this case, you cannot do without special tools.

Alternatively, in search of suitable materials, you can contact your nearest tire shop. Usually, in such places they are happy to give away unwanted tires. One swan needs one tire. If you want to experiment with the shape of birds, take several. Before starting work, the rubber must be washed and dried. All work is best done outdoors.

Marking the diagram on the tire and cutting

The appearance of the swan depends on the marking scheme. During operation, the tire will need to be turned out. The difficulty of this process will depend on how you make the cuts.

We'll tell you how to make a birdhouse with your own hands.

Step-by-step instructions for making a swan with your own hands:

Tire markings for making a garden swan.

Use chalk to divide the tire in half. Then outline the beak, head and neck. The length of the neck together with the beak should be more than half the circumference of the tire. The R13 wheel has a circumference of 180 cm, respectively, for the neck you need to measure about 95 cm. For a proportional head you need 10 cm, the beak length is 9 cm.

• The tire must be cut along the marked lines. A knife can handle old-style tires with a nylon cord. To make the job easier, prepare a soapy solution and dip the cutting object into it from time to time.
• Metal cord will not yield to a knife. You can use a grinding machine. You should work exclusively outdoors, and do not forget to wear closed shoes and work gloves.
• Please note that working with tires increases the consumption of laps. You will need about 3 disks per swan. In addition, heated rubber does not spread the best smell around, soot and soot are guaranteed. The grinder cuts quickly, but is not environmentally friendly.
• It's more pleasant to work with a jigsaw. To start the file you need to make a hole. You can use a chisel or drill. Wear on jigsaw blades increases when working at high speeds. The best option is to work at lower than average speeds using a saw with a reverse tooth. This way you can saw through the metal cord without any problems: the reverse stroke of the saw will simply tear it, and the low speed will prevent the rubber from heating up too much.
• For adherents of hand tools, a metal file is suitable. It will also cope with steel cord, but the speed will be lower. What paths made from plastic bottle caps are is described.
• The splint should be cut along the contour of the neck and head; transverse cuts are not needed. As for the sequence, the biggest mistake that beginners make is to completely cut out one side of the neck. If you cut the tire on one side, it will be quite difficult to cut the other.

• The next stage is the tail. Its length is about 25 cm. It will become an additional decorative element and will make it easier to turn the tire out. It is cut out in the same way.
• The workpiece must be turned out. The process is labor-intensive and looks like this: the workpiece is placed with the cut part down, it is pressed down with a foot and pulled, turning the side parts up. The central part needs to be pushed through.
• Now the design really resembles a swan. The side half rings need to be lowered down. If you took a tire with a metal cord, then the edges need to be processed with a grinder. But even such a procedure will not be able to completely smooth out the protruding reinforcement. Therefore, swans made from steel cord tires are suitable only for decoration, but not for children's playgrounds. Touching sections with protruding wires is unsafe for adults, let alone children. Find out more about crafts made from tires for the playground.
• In order to give the swan the desired shape, the neck should be strengthened. For fastening, you need to drill two holes along the entire length of the neck every 15 - 20 cm. They need to be located along the center line. Brackets made of thin soft wire are inserted into the holes. Use staples to secure thick steel wire. It will need about 1.50 m. The lower end is fixed on the inside of the neck, at the base of the splint, the upper end is fixed at the level of the head.
• The swan is almost ready, you just need to bend its neck appropriately and make eyes out of rubber. They can be fastened with screws. For decoration, the edges of the wings are cut, then the notches resemble the plumage of a bird. If you want to have a swan princess in your garden, make a crown from a plastic bottle.

Painting tire sculptures

In order for the birds to look extraordinary and aesthetically pleasing, they need to be painted correctly. For swans, the color usually chosen is white or black. Silver and gold sculptures look good. Any durable paint for exterior use will do.

Rubber can be painted well with oil, enamel and nitro paints. Do not forget that any paint is applied to a clean, dry surface. Correctly applied paint adheres well to the sculpture, does not deform and lasts quite a long time. Leftover car paint aerosols will do. Then the work will go quickly. An evenly painted surface can be decorated using acrylic paints. Draw the head, beak, plumage. Such swans look more naturalistic.

Return