Hi all Dear friends, today I will show you a great idea on how to make a mini vacuum cleaner to clean your keyboard. With this vacuum cleaner you can easily clean the keyboard and various circuits. This vacuum cleaner is also portable and can be used to remove dust anywhere.
Necessary materials:
- soap bubble container
- motor
- bottle neck
- neck from detergent
- crown
- switch
- connector
- thin metal
- pen
Step 1: First of all we need to make a propeller. From tin can cut out a circle (diameter should match internal diameter container). Then we drill five holes: one in the center and four on the sides, as shown in the photo. Then we make cuts and bend the blades to form a propeller.
Step 2: Then we take the neck of the bottle and attach the motor to it using glue. Then we attach the propeller to the resulting structure. And we secure it all into a container.
Step 3: Then with reverse side container, make small holes. Next, take the neck of the detergent and glue it, as shown in the photo. Glue a small section from the handle to the neck.
Cut out a small piece of breathable fabric and insert it as shown in the photo.
That's all! Our mini vacuum cleaner for cleaning the keyboard is ready, insert the crown and use it.
Making a homemade vacuum cleaner with your own hands is very easy. This device is useful in various everyday situations.
Need a vacuum cleaner urgently? Was it broken or was it not at hand? Did you know that you can make it yourself? To do this, it is enough to have the most common items that are present in any apartment: empty bottles, wires, scraps of tubes, hoses, broken toys that you were sorry to throw away. First of all, you need to get a small working electric motor somewhere. This is the basics. It can be borrowed from a broken children's toy or any unnecessary electrical appliance. Having obtained it, you can start making small vacuum cleaner.
- Take a plastic soda bottle and cut off the neck where it expands. From the cut of the neck, measure the excess part and cut it off so that the remaining space is enough for the dust collector and motor.
- Fan. You can borrow an old fan from the computer system unit. If there is none, then find a piece of soft metal of a suitable size. Possible from under tin can beer. The main thing is that it can be easily cut with scissors and then bent. The diameter of the fan wings must match the inner diameter of the bottle. Cut out a circle and mark it into 6-8 equal parts. Cut the marking lines, leaving 5-10 mm to the center of the circle.
- Make a hole in the center for the motor rotor, and bend the fan blades at an angle so that they suck in air during rotation, and not vice versa. Fasten the fan and motor rotor with glue, trying to avoid distortions in the connection.
- Make holes in the bottom of the bottle to allow air flow to escape. Attach the motor to the bottom of the bottle. A plastic cover is useful for this. Glue it to the motor, after threading the wires from it into the hole on the side.
- Place the fan inside the bottle and glue it to the bottom. To the top of the bottle inner side glue the seal.
- Make a ring from any wire. Place the ring on top of the seal and glue a circle of thin fabric onto it. Cover the structure with the top of the bottle. Then glue a small hose to it. The nozzle can be made from half of an unnecessary plastic bottle.
As you can see, making a homemade vacuum cleaner with your own hands is quite easy. This device is useful in various everyday situations. The power of a small vacuum cleaner, for example, is quite enough to clean the keyboard from dust and bread crumbs. The made device can be easily transported from place to place, not only in the house. It can be used to clean seats and panels inside the car.
There are different situations in life. If you suddenly need to use a mini vacuum cleaner, you can save on the purchase and make it yourself.
1. Trace the label along the top and bottom lines. Cut out the part of the bottle where the label was marked.
2. Take an old empty can or tin, remove the bottom and top, then cut down the middle to make a rectangular sheet.
3. Measure and cut a circle from the tin according to the diameter of the bottle.
4. Leaving space in the middle for small motor, draw a tin circle and make cuts to make 8 sectors. Each of them needs to be slightly bent. Make a small hole in the center.
5. Now attach the motor to the resulting improvised fan.
6. Using a drill and a large drill bit, make 3 rows of holes at the bottom of the bottle.
7. Glue the cap from another bottle to the motor, after threading the wires from the motor into the hole on the side.
8. Place the fan inside the bottle and glue it to the bottom. Glue the seal to the top of the bottle on the inside.
9. Make a ring from wire with such a diameter that it fits into the bottle and can be placed tightly on top of the seal. Glue a circle of thin fabric onto the ring.
10. Place the ring in the bottle on the seal and tightly close the structure with the top of the bottle.
To quickly clean hard-to-reach areas of the workshop workplace, your son’s computer and others from dust Appliances, I made my own mini vacuum cleaner. It took only two to make it. plastic containers, a small engine and one free evening. The design turned out to be not only useful, but also easy to use.
On the engine direct current With a voltage of 12 V, a protective casing made of tin (photo 1) d 100 mm was secured on the axle side.
I made an impeller from plastic (photo 2) - I cut out a circle d 95 mm with a jigsaw and glued ribs measuring 30x15 mm to it on one side perpendicularly. Finished part fixed it on the motor axis with glue from a hot-melt gun.
I assembled a garbage container from a cut PET bottle and a plastic bucket. I installed a tube from a syringe into the upper part of the body to attach the hose.
From a tin can required diameter(must match the diameter of the PET bottle) I made an air intake (photo 3). I drilled several holes 5 mm in diameter in the walls of the container, and fixed a cut-off tube from a syringe in the bottom in the center.
Fastened the part to protective casing engine with bolts so that the gap between the impeller and the bottom of the intake is approximately 7 mm.
I installed the finished unit (motor with intake) into the housing and drilled holes in the plastic at the level of the holes on the intake. The connection point was coated with superglue for reliability and rigidity of fastening.
To connect the device to the network, I soldered the 12 V power supply wires to the motor contacts. A hose was secured to the tube in the housing using a metal adapter.
DIY mini vacuum cleaner – photo
DIY mini vacuum cleaner - video (option)
2019 High Quality C30B Robot Vacuum Cleaner, Map Navigation, 3000Pa Suction, Intelligent…
15310.08 rub.
Free shipping★★ ★★ ★★ ★★ ★★ (4.90) | Orders (965)
ILIFE V55 Pro vacuum cleaner robot sweep & wet mop virtual…
At the moment, the market is flooded with not only universal, but also special industrial ones. But if you want to save money on buying them, you can try making your own.
Such devices are quite expensive, but they are necessary during repair work to quickly clean up your workplace after yourself. Using an ordinary vacuum cleaner you will not be able to achieve High Quality
cleaning, as they are not designed for such garbage.
Household models are not able to quickly and efficiently clean surfaces from oil, chips, fragments of plastic, glass, etc. Before you make such a vacuum cleaner, you need to decide with the scope of work
, since some models are designed for cleaning liquids or even small crushed stones. Once the operating principle has been determined, all other parameters should be considered. There are many real examples self-creation industrial vacuum cleaners . Let's consider the option of manufacturing from old model
"Rocket".
What will you need for the job? If you have an old Raketa vacuum cleaner lying around at home, it will be great consumables
to create a building (for more details about what else can be built, see the article).
- In addition, you will need the following tools and materials:
- Bulgarian;
- screwdriver;
- bandage;
- pipe 200 mm long and 40 mm in diameter;
- metal scissors;
- plastic bucket with lid and handle;
- glue;
- insulating tape;
- drill.
- scotch;
self-tapping screws
Let's start creating a construction vacuum cleaner Initially you need to do garbage disposal,
which needs improvement. Armed with a screwdriver, unscrew the wheels from the base of the vacuum cleaner and tightly seal all the resulting holes with tape. After the nameplate is removed, its hole must also be sealed with tape.
All fasteners are removed. Now, using a grinder, you need to free the body from all rivets and install a plug, previously wrapped with insulating tape. Next, make a hole in the bottom using a drill, 43-45 mm in size. A gasket is used as a gasket, approximately 3-5 mm in thickness.
Next, holes are made outside the suction pipe. Before doing this, you need to make marks at an angle of 15 degrees. Using metal scissors, make a hole. After this, we attach the pipe using self-tapping screws. For maximum tightness, it is necessary to thoroughly saturate the bandage with glue and wrap it around the nozzle.
The nuances of such a device
In order to assemble your construction vacuum cleaner, you need to have on hand power unit , the revolutions of which must be at least 6,000. As for the available material, it can almost always be found at home. As a donor for the engine, you can use not only an old vacuum cleaner, but also a washing machine.
Some craftsmen use it for homemade vacuum cleaner power units from kitchen machines, but do not forget about their tendency to frequent breakdowns due to inability to withstand high loads.
If the power unit is found, then you need to take care of it tightness. You will also need a fan. Very often, an ordinary bucket is used as a body for a vacuum cleaner, in which a hole is made. Naturally, you need a container for garbage and a filter that can be used.
The presented videos show several assembly variations construction vacuum cleaner. It is recommended to study them if you decide to create a homemade model.