If you don’t want to buy spinners in a store, feel sorry for your hard-earned money, are too lazy to wait for delivery, or just have a creative impulse in your soul, then you can try to assemble the spinner yourself.
With equal hands, the toy will turn out no worse, and often even better than the one purchased - after all, you have invested a part of yourself in it.
How to make a spinner yourself
Method 1: make a spinner from bearings
We will need bearings, for example, from a skateboard. Before using the bearing in practice, it is necessary to clean it of grease, otherwise the turntable will rotate quietly, but not for long. This method is very simple, since we don’t have to make the spinner body; all we need are four bearings.
They must be laid out in the correct shape. To make this shape accurately, use a squared notebook sheet. Once we have a perfect triangle, we glue the bearings together with glue - preferably superglue or cold welding.
Or you can draw a circle with a compass and divide it into 3 parts, like a Mercedes icon. Drawing and geometry lessons to help.
When the glue has dried, it is necessary to increase the gluing area, to do this we sprinkle the glue with salt, then the area will increase and the bearings will stick to each other better. At the end, we wrap the gluing areas with any thread and impregnate it with glue, this will give even more strength.
Several video instructions on how to make a spinner from bearings:
And another option without a rope:
2nd method: spinner with clamps
For the next method we will need two ties or clamps. They need to be inserted into each other. After this, we place three bearings in the center of the zip ties and tighten the zip ties until they hold tightly.
Cut off the protruding ends. In principle, at this stage, the spinner is already ready, but it does not hold firmly. If the turntable falls, everything will fly out of it. We don't need this, of course. Therefore, it is necessary to make it more reliable using glue. In all places where the bearings engage, where the ties touch the bearings, it is necessary to apply glue.
Such a spinner, due to its high degree of gravity, spins for less time and not as fast, but it is easier to manufacture.
To learn more about how to make a spinner with ties, watch the video:
How to make a spinner without a bearing
We will need: six plastic bottle caps, a toothpick, a large gel pen refill, coins and glue.
- First, take one of the covers and make a hole in it using a burner or soldering iron, or in extreme cases, a hot metal nail.
- Now we cut off a small part from the rod, about a centimeter long, and glue it into the cork.
- After this, we take two more plugs and cut off the top part.
- Then take a toothpick and cut off the sharp ends so that you are left with a stick about three centimeters long.
- Using glue, glue it to the top of the cork.
- After that, we pass it through part of the rods and glue the second plug. The middle plug should turn easily.
- Finally, we just have to glue the remaining three plugs.
To understand what we are talking about, watch the video where there will be step-by-step instructions on how to make a spinner from plastic bottle caps:
As a result, we have already got a pretty good spinner, but in order for it to spin even better, we need to make it heavier. For this we will use coins. Take a coin and glue it to each of the plugs. That's all, our spinner is ready.
How to make a paper spinner
1st method: from cardboard
We make a template for the spinner from cardboard using a plastic bottle cap.
- We circle it so that we get a triangle. We connect the circle with the rest of the circles with smooth lines and cut it out.
- Place the finished template on cardboard, trace it and cut it out.
- We also need four more circles of smaller size, let's make them.
- Now we need coins. We take them and glue them on the sides of the first half of the spinner, and glue the second half on top.
- Using nail scissors, make a hole in the center of the spinner.
- Next, we need to cut off about a centimeter of the rod from the handle, and make small holes in two small circles.
- All the details are ready, now you can paint our spinner with paints to give it a more beautiful look.
- Now we assemble our spinner from the resulting parts. We insert the axle into one circle and seal it, insert it into the spinner and press it on the other side with another circle.
- Glue the remaining two circles on the sides. That's all, a homemade paper spinner without a bearing is ready.
To understand the details, watch this video:
Method 2: paper spinner
To make such a spinner, we will need two square sheets of paper and two pushpins. The assembly diagram will look like this:
We advise you to immediately watch the video, otherwise the instructions may seem too complicated:
- Fold the sheet in half, then open it, like a book, fold both sides of the paper towards the bend.
- Next, we fold the resulting rectangle again and get an even smaller rectangle.
- Fold the resulting figure in half to create a bend. Then we open it and place it vertically.
- We take it from the lower left corner and move it to the right side. You should get a figure similar to the English letter L.
- We repeat the same with the other part of the paper, only now we bend it to the left.
- From the resulting shape, bend each corner so that you get two triangles at two ends.
- We make a diamond out of the resulting shape, run our fingers along the curves several times and open it back into the previous shape.
- We repeat the same with the second sheet of paper, only at the folding stage we make the folds in the opposite direction.
- We connect the two resulting figures together. We place one vertically, the other horizontally on top. We tuck the corner of the vertical fig into the corners of the horizontal one. As a result, you should end up with a figure that looks like a shuriken.
- Now we make a hole in the center of our star using a pushpin so that it can easily rotate.
- Now we take the second button, heat the iron tip and take it out. We put on the remaining cap on the other side. The spinner is ready.
More interesting articles.
If you look around, most likely you will see a person who is constantly spinning some kind of propeller in his fingers. This item is nothing more than a spinner or fidget - a kind of spinner, which consists of a bearing and a petal body.
The spinner was developed by Katherine Hettinger, who decided to create a useful exercise machine for her daughter with myasthenia gravis. At first, the woman made toys from adhesive tape and paper, and then began producing fidget spinners. Back in 1993, she received a patent for her invention, but no companies were interested in making it. The patent for this toy has long expired, so every second person in the world can produce it.
Spinners are far from being the same type; they vary in size, shape, color, and some can even glow in the dark. They vary in price; some models can cost several hundred dollars.
What is a spinner
What a spinner is, both a small child and a respectable adult in an expensive car can tell. The spinner has no age restrictions, since its design is designed in such a way that it simply does not have sharp corners or the smallest details.
This device is a gyroscope that is incredibly stable in space. With its help, interesting tricks are performed that invariably attract the attention of people around.
Spinners are produced by a huge number of companies that are trying to surpass their competitors. They are trying to release the most unusual model, for which you won’t have to pay a tidy sum. It is worth noting that no company in the world has pre-emptive patent rights to produce spinners.
Playing a spinner is as safe as possible, since it does not require additional devices or any specialized places to play. The spinner never leads to injuries, it not only does not spoil the psyche, but also weakens obsessive states and autistic manifestations.
It is worth noting that this device operates solely on physical strength; it does not have batteries or a motor. The spinner is easily set in motion with a snap of the fingers. In order to start the propeller, you simply need to hold the axle between your middle and thumb, and start the blades with your index finger. In some cases, it is possible not to pick up the toy, but simply place it on the table, which greatly increases the speed and time of its rotation.
What is included in this device? The spinner consists of:
- covers - inserted into the middle of the bearing and helps to hold the entire structure;
- housing - the part that rotates around the bearing;
- bearing - the main part, which is a ring stuffed with metal balls.
The rotation time of the spinner is very important, so the most expensive devices are based on high-quality bearings. Although the cheapest option will spin for about two minutes, and the most expensive spinners will spin for more than ten minutes.
How to make the spinner spin longer without replacing the bearing? You just need to try to clean it of dust particles and debris that create friction and prevent the structure from rotating for a long time.
You need to clean the spinner using:
- acetone;
- brake fluid;
- oil paint thinners;
- isopropyl alcohol;
- dishwashing liquids;
- soap
In order to quickly dry the bearing of this spinner, it is recommended to use a hair dryer.
There are a huge number of spinners of various types:
- single - consists of one blade and a bearing, they are mobile and powerful because they can rotate for up to five minutes;
- three-spinner – is a trefoil clover, in the center of which there is a high-quality bearing;
- quad spinner - looks like a cross or a mill with four petals, however, it weighs quite a lot and cannot satisfy everyone with its size;
- wheel - this type speaks for itself, since it looks like a cart wheel;
- exotic - a rather expensive option, since the spinners are made of zirconium or tungsten and are designed in the form of weapons of super heroes or even medieval instruments of torture;
- created using a 3D printer - they can be printed and assembled in about an hour, so they are in demand, and they are also quite cheap.
The spinner is rightfully the best toy of 2017, which invariably attracts attention and is a welcome gift for a special occasion.
When purchasing it, you should take into account factors such as aesthetics and vibration, ergonomic or rotational properties, durability and rarity, precision of processing and its quality. These relaxation toys are made from plastic, wood, different types of metals, and leather.
What is a spinner for?
It is not yet clear exactly why a spinner is needed. Some people use it as a toy, a finger trainer, or just a sedative. Agree that it is much more harmless to twirl the propeller of a spinner while standing in a long traffic jam than to click a pen or bite your nails. It is also a reliable means of focusing on any information or task.
By the way, a spinner is a rather interesting simulator that can teach the basics of juggling.
So, what is a spinner and what is it for, and what benefits can the use of this kind of toys bring:
- will develop fine motor skills of the hands;
- will help develop hands damaged during injuries or accidents;
- relieves stress and anxiety;
- will help to relax while a person quits smoking;
- improves mood;
- will develop the right hemisphere of the brain;
- releases accumulated negative energy;
- will increase a person’s response to external stimuli;
- will speed up your thinking processes.
The negative aspects of this device include the possibility of injury or swallowing balls from the bearing. In general, spinners are often declared to be a successful marketing project.
How to make a spinner without bearings at home
Having found out the cost of the option they like, many people begin to seriously think about how to make a spinner without bearings at home.
It will be quite possible to make a hand trainer without using expensive bearings. On the Internet it is quite possible to find drawings of such homemade spinners from scrap materials.
This spinner without bearings is made of paper, for this you should prepare:
- two sheets of thick A4 paper;
- ruler;
- compass;
- a simple pencil;
- toothpicks;
- glue for paper and for parts.
How to make a spinner without bearings for children
How to make a spinner without bearings for children can be found on our website. In order to make this kind of structure for kids, all the same elements are used as for an adult.
However, it is worth checking that all parts and related materials are, of course, environmentally friendly and safe. For example, for very young spinner users, you can use finger paints and environmentally friendly glue.
When making a design with and for a child, be sure to blunt the tip of the toothpick. Bearings are never used, since the baby can swallow balls from them.
How to make a spinner without bearings and caps
How to make a spinner without bearings and covers? Just try using cardboard and use glue stick caps for the template.
In order to make the main bearing, you need to use a hairpin, a toothpick, and a ballpoint pen.
You should use a compass and ruler to measure all dimensions as accurately as possible. Not only the appearance, but also the properties of the spinner, including speed and rotation time, will depend on whether the measurements are taken correctly.
How to make a spinner without paper bearings
Many young people ask questions about how to make a spinner without paper bearings.
- draw a rectangle 9X2 centimeters;
- draw diagonals to determine the center;
- fold this drawing several times;
- cut out about eighteen rectangular pieces;
- place two identical coins on their opposite edges;
- circle the coins, giving the edges a rounded appearance;
- glue all the cut out parts together with paper glue;
- to make it heavier, glue it to the edges of the coin with special glue for parts;
- measure 2 centimeters using a ruler and compass;
- draw and cut out eighteen circles that will become the central bearing;
- punch a point in the center that will be slightly larger than the diameter of the toothpick you are using;
- insert a toothpick into the center;
- put nine two-centimeter circles on it on both sides;
- carefully glue the joints of the toothpick and the mug, in no case without sealing the hole itself;
- let the future spinner dry and give it an aesthetic appearance with scissors;
- practice spinning the structure while softening the friction of the spinner;
- paint this homemade product in your favorite colors or stick on your favorite logos.
How to make a spinner without bearings from caps
Many people are interested in how to make a spinner without bearings from caps. Of course, the ideal option would be to make a homemade spinner using one or more bearings.
When using bearings, you should find the correct main element, wash off the grease from it and remove dust particles. If you make a spinner yourself without bearings from caps, then you won’t have to perform these actions.
You should prepare several caps from plastic bottles in advance; the best option would be to use three pieces. They will need to be glued to each other on the sides using Moment glue.
In the middle you will need to drill a small hole into which the ballpoint pen will fit. It is worth cutting a three-centimeter piece from the empty rod, which is inserted into the hole.
It will be possible to rotate this structure by holding it with two fingers.
How to make a spinner without bearings from Lego
To understand how to make a spinner without bearings from Lego, follow simple instructions. To assemble the structure you need to prepare:
- a flat and maximally long cube with holes;
- kernel;
- two round stoppers with a cavity inside;
- several flat, round cubes for your fingers.
After all the parts of the future spinner are prepared, you should stretch the rod through the hole of the long cube, and then limit it on both sides.
Then you need to easily and quickly tighten the round platforms intended for the fingers. The side edges of the spinner should be balanced and positioned symmetrically. That's all, you can start relaxing with the help of a turntable.
How to make a spinner without bearings from coins
The Internet is replete with instructions and diagrams on how to make a spinner without bearings from coins. The simplest option would be to make a simple spinner from caps with coins glued to the inside or outside of them.
You can take coins worth five Russian rubles, and then make holes in them using a drill or soldering iron. Then you should insert three-centimeter pieces of a ballpoint pen into them.
How to make a spinner with your own hands from a plastic bottle
Another popular request on the Internet is how to make a spinner with your own hands from a plastic bottle.
To do this, you should select a bright plastic bottle and cut a strip 10-11 millimeters wide from it. This is done in order to cover the bearings, which are 8 millimeters wide.
You should also take thick plywood, three nuts and three self-tapping screws for 19, as well as four washers. Make three holes in the plywood into which you need to insert a nut, a washer and tighten the self-tapping screw.
Bearings should be placed between them, aligning them as much as possible, and millimeter washers should be placed under them. The bearings should be pulled together from a plastic bottle and the structure should be heated with a hairdryer.
After drying, carefully tighten the structure, and then unscrew the nuts. In a few minutes it will be possible to use the spinner.
How to make a spinner with your own hands from wood
To understand how to make a spinner from wood with your own hands, you need to read the instructions or watch an instructional video.
It is quite easy to make for those who have a little knowledge of a drill and a jigsaw. Choosing the right wood is essential, but novice fidget spinners can try creating a masterpiece using thick plywood.
You can come up with a drawing of the future spinner yourself or find it on the Internet. Then you need to attach your drawing to the plywood, trace it, and then cut it out using a jigsaw (preferably an electric one).
The workpiece should be cleaned with sandpaper, a hole is made in it with a jigsaw or drill, since then it turns out much smoother. A little trick for a novice craftsman: you should drill the hole halfway, then turn the plywood over and do the same on the back side.
Do not forget that the thickness of the plywood should not be thicker than the width of the bearing. If the wood is thicker, it should be trimmed and sanded.
This spinner can be opened with varnish or oil, and also aged using a lighter.
How to make a spinner with your own hands in 5 minutes
How to make a spinner with your own hands in 5 minutes? You should use available materials, for example, bearings and different types of glue; leather, sequins, and beads are used for decoration.
The most original spinners that can be made with only five free minutes are made from shell casings, a bicycle chain, copper, and even from an iPhone that its owner does not need.
Kids will quickly be able to create a beautiful and bright spinner from ordinary thick cardboard. Children and parents will have a great time constructing such a toy, and will also save money on a good book or something useful. Schoolchildren can propose making such a product from cardboard during craft lessons, and the teacher will support this initiative.
It is also possible to create a spinner solely from bearings or not use them at all. In general, there are a lot of options, and what exactly your spinner will be will be determined by a flight of fancy.
How to make the spinner spin faster? You just need to remove excess grease from the spinner bearings. To do this you need to go through several steps:
- drip high-quality lubricant;
- change a bearing that has served for quite a long time;
- change the plastic spinner to a metal one;
- place a high-quality plug on the structure that will protect it from dust, moisture and dirt;
- clean the spinner several times a week using a hairdryer or a can of compressed air;
- do not try to remove and clean the bearing on cheap models, this is simply unrealistic and not provided by the manufacturers.
The spinner is a very popular thing among teenagers and adults. It helps to concentrate thoughts, relax, and relieve psychological stress. You can buy a spinner in almost any store, but it is much more interesting to make it yourself. Below are instructions for assembling different spinners with your own hands.
How to make a spinner with your own hands - a simple spinner
In order to make a simple one with your own hands, you will need the following materials:
- 5-6 bearings.
- Ties.
- We spread the bearings lengthwise, pressing them tightly against each other.
- We connect 3 ties in the shape of a triangle.
- We put the resulting figure from the ties onto the bearings.
- We tighten the bearing on one side so that they fit the bearings tightly. We cut off the protruding tails. The resulting structure should look like caterpillars.
- We take 2 more ties and tighten them vertically, along the edges of the second bearing. We cut off the protruding tails.
The spinner is ready.
How to make a spinner with your own hands - a star spinner
In order to make a star spinner with your own hands, you will need the following materials:
- 4 bearings.
- Super glue.
- Threads.
- Sandpaper.
- Soda.
We perform the following simple steps:
- We arrange the bearings as follows: two vertical bearings are pressed tightly against each other, the remaining two are on the sides of the second vertical one.
- We clean the spinners with sandpaper in the place where we will glue them.
- We glue the spinners in the shape that we set initially, sprinkle the gluing areas with soda for greater strength.
- We wrap the joints of the bearings with threads.
- We also put super glue on the threads to prevent them from unraveling.
- The spinner is ready.
How to make a spinner out of wood with your own hands
In order to make a spinner out of wood with your own hands, you will need the following materials:
- A piece of wood.
- Drill.
- 3 bearings.
- Sandpaper.
- Pencil.
- Saw.
We perform the following simple steps:
- We place three bearings on a piece of wood, at an equal distance from each other.
- We outline the bearings with a pencil.
- We connect the resulting circles so that we get a figure with the shape of a caterpillar.
- We step back half a centimeter from the caterpillar and draw the shape of the future spinner.
- We drill circles with the expectation that the bearings will sit tightly in them.
- Cut out the resulting shape.
- We clean the resulting shape with sandpaper, getting rid of sharp corners and splinters.
- We insert the bearings.
The spinner is ready. If desired, you can always paint it any color using a spray bottle.
Spinners entered mass fashion not so long ago, but in just a few months they won the hearts of not only adults, but also children. Today, spinners spin everywhere: on the street, at work, in the subway and even in kindergarten! And every child wants his toy to be somehow different from those that his peers already have. You can buy an original spinner, but such a toy is not cheap, and finding a unique spinner takes a lot of time. The best solution is to make a spinner yourself.
So, we bring to your attention several simple ways to make a spinner with your own hands from materials that every home has.
1. How to make a spinner from plastic caps?
Materials: caps from any plastic bottles of the same size (4 pieces), plasticine, hot glue, nail, scissors, lighter and toothpick.
What do we have to do: put plasticine in 3 lids, use hot glue to seal the remaining space of the lids. Take the fourth lid (without plasticine) and make a hole in it, for example, with a heated nail. Glue the caps with sand to the one where you just made a hole. Take a glue stick and cut 2 small pieces (1 cm) from it. Break a toothpick in half and put a piece of glue on one end (make sure that the sharp tip of the toothpick does not stick out) and place it in the center of your future fidget spinner. Place the remaining piece of glue stick on the back of the toothpick. Your spinner is ready!
For a more interesting look, you can paint the lids in different colors with acrylic paints.
2. How to make a spinner from cardboard?
Materials: plastic bottle caps, cardboard, scissors, marker, awl or nail scissors, glue, 3 coins and a pen refill.
What do we have to do: Using the lids, draw 4 circles on the cardboard in the shape of your future spinner. After this, cut out 5 such blanks and glue them together, carefully gluing the edges. Next, cut out smaller circles. Using an awl or thin nail scissors, make a hole in the center of the spinner. Glue 3 coins or any stickers on the sides of the blanks.
Next, take the set aside pen shaft and carefully cut 1 cm from it. Make small holes in the center on two small circles. Insert the cut piece from the handle shaft into one of the circles and glue it along the edges of the hole to securely fix it. Insert this circle into the center of your spinner and glue the second circle on the back side. The two remaining small circles can be glued on top of the ends of the rod. To make your spinner spin faster, place some kind of spacer between the spinner blank and the small circles (in our example we used metal pendants).
Ready! Let your child decorate his spinner as he wants, you can use glitter, stickers, rhinestones and other decorations.
3. How to make a spinner using bearings?
Materials: bearings (3 pcs), tie clamps, glue gun or superglue (for a more complex spinner).
What do we have to do: wrap cable ties around the bearings on all sides. Cut off the excess clamps and that’s it - the spinner is ready!
To make it more bright and attractive, you can make the design more complex. Take 7 bearings, place 6 of them around the seventh. You will not use all 7 bearings, you will only need 3 circular and 1 central. You need the remaining bearings only for accurate measurements, so we will leave only those that form a triangle. Glue all the necessary parts using a glue gun or superglue. The spinner is ready! Decorate the spinner as you wish. You can glue the fluffy wire, apply glue to the sides of the spinner and cover the edges with glitter.
Rest assured, no one else will have spinners like your child’s!
The spinner is a fashion toy invented in the USA. It appeared in Russia in 2016 and has already gained extraordinary popularity. What is it? She is called a spinner, a spinner, a fidget.
It develops fine motor skills of the fingers, relieves anxiety and has an anti-stress effect. Fidget spinner is not only a toy designed to entertain children and adults. This is a great way to spend time waiting, traveling in public transport, and queuing. This turntable also allows you to get rid of bad habits, such as tapping your fingers on the table surface, repeating hand movements, and even the habit of smoking. It will allow you to get rid of the bad habit of twisting something in your hands. The working principle of the fidget spinner is the use of a bearing in the middle of the product with petals.
The fitget has two, three, four, five, and some models even six petals. The most common are toys.
The spinner is made of wood, brass, bronze, plastic, and can be combined.
Two types of bearings are used: metal, like, or with ceramic balls. Characterized by rotation time. The spinner rotates from one minute to several tens of minutes. The longer the rotation occurs, the better the quality of the toy.
The cost of the product is influenced by the use of high-quality materials in the manufacture of the body with petals. The easiest way to buy a spinner is in.
Making wood in a home workshop
However, a person familiar with tools can make such a toy for himself. For this you will need:- A small piece of wood, preferably hardwood;
- Bearing (suitable for a broken skateboard);
- Sleeves or suitable pieces of round metal;
- Epoxy adhesive.
Video with instructions for making a spinner from wood
First of all, we mark out a piece of wood. A square piece is required.
We drill a hole in the center and expand it to fit the external dimensions of the bearing. The thickness of the workpiece must be equal to the thickness of the bearing. The next step is to insert the bearing and glue it with glue.
On two opposite sides we drill two holes equal to the smaller diameter of the sleeves. Then we take the polished sleeves, glue them in pairs and mount them with glue in the prepared holes of the board. Let the glue dry.
We clean, sand and paint in the color you like. A simple spinner with two petals is made at home. In the same way, you can make a homemade gadget from plexiglass or PCB.
It is more difficult to make a product with three petals. To do this you will need a drawing, a jigsaw and a protractor. The diagram below clearly illustrates how to make such a toy.
Paper spinner
- It is much easier to make a hand-held spinner from paper.
- We print the drawing on a regular printer.
- Transfer the drawing to thick paper or cardboard.
- We cut out 15-20 samples according to the template. Using scissors, we make a hole for the bearing, slightly smaller than the outer diameter.
- Glue the cut out samples with PVA glue.
- Place under the press.
- After the glue has dried, insert the bearing.
- We clean it with scissors and, if necessary, sandpaper.
- Paint it in the desired color. The toy is ready.
Video with instructions for making a paper spinner without a bearing at home
As you can see, the cost of the product consists mainly of our own work, because Parts from out-of-circulation mechanisms were used for production.Before assembling the gadget, inspect the bearing. To do this, remove the anthers and wash them. This completes the work on making the turntable.
Luminous
- The most interesting toys come from making them yourself from absolutely incredible materials. Make a glowing fitjet - all you need to do is buy a phosphor online in China.
- Dilute 3 grams of powder in 7 ml of glycerin to obtain a luminous liquid.
- Then you can use the described method for making the central part from wood. Just use glass bulbs from fluorescent lamp starters instead of sleeves.
- We pump liquid into the flasks using a syringe and glue them into the prepared holes.
Made from chocolate
Any material you can imagine is suitable for making a spinner. It can be made from wax, paraffin candles, ice and even made edible.A very original gadget is made from chocolate.
I played and got tired of it and ate it.
To make such a toy you will need:
- Make a mold for filling;
- Bearing;
- Candies such as confetti or jelly beans;
- Cardboard, for form and glue;
- Wax paper;
- Scissors with pencil;
- A piece of foil from a chocolate bar and the chocolate itself;
- Glue.
Video showing how to make an edible chocolate spinner
- A drawing is taken from which the twist template is cut out. A strip slightly larger than the thickness of the bearing is cut out of paper and glued along the perimeter of the template.
- Then we completely wrap the prepared bearing in foil and place it in the center of our mold, having previously placed wax paper on the bottom of the mold. We place candies along the edges of the petals (you can do without candies, this is for beauty). All that remains is to dissolve the chocolate in a water bath.
- As soon as the chocolate becomes liquid, it is poured into the mold using a pastry syringe. It is necessary to pour very carefully so as not to move the installed parts.
- After filling everything with chocolate, place the toy in the refrigerator. After some time, the chocolate will harden and can be removed from the refrigerator.
- All that remains is to remove the product from the mold, free the bearing from the foil, clean the edges - and you can use it. When you get tired of it, you just have to eat it.
- The entire manufacturing process can be filmed and shown to friends or posted on the Internet on your page.
- In a similar way, a fitjet can be made at home from any hardening material: stearin, wax, gelatin, and from colored wax candles you can get a multi-colored spinner body.
- The gadget should rotate smoothly and without noticeable beats.
- The quality of workmanship should not cause any complaints.
- The material from which the toy is made must be of high quality.
- The rotation is quite long: the longer the better.
So we see that no one can give an unambiguous recommendation. Focus on your own feelings. To ensure that the pinwheel serves for a long time and is always attractive, follow the recommendations:
Protect the toy from mechanical damage, falling from a height onto a hard surface;
If the product is made of plastic, it is not recommended to disassemble it, especially the button - the plastic parts can be damaged; they are glued or pressed in very tightly;
Periodically wash and lubricate the middle bearing using a syringe with a needle. Wash with gasoline, preferably for lighters, it has almost no odor. It is recommended to lubricate with watch oil in a small amount. Mineral oils should not be used for lubrication.