How to cut a hole in a countertop for a stove. How to install a built-in hob in a countertop? induction hob

This step-by-step instruction is about how to cut a hole in a chipboard or MDF countertop for a hob with your own hands. When you do, you probably need to know how to cut holes in chipboard or mdf countertops if you're installing a sink or hob. This task may seem simple, but we can assure you that there are many nuances that need to be taken into account for a good result.

On the one hand, you must carefully follow the contour of the gas stove using a template or follow the instructions indicated on the product. In most cases, there are certain restrictions that you should pay attention to, such as the minimum distance from the stove to the back or both sides, to. Use a large L-shaped square to draw a rectangle on your desktop, otherwise the corners will not be square.

To get an accurate hole, you must use a good saw with the right blade. Therefore, the blade must have teeth oriented downwards, otherwise it will split the surface. Drill initial holes along the four corners of the rectangle using a drill or (the hole should be wider than the size of the jigsaw blade).

Work plan for installing the hob in the countertop

Materials:

• countertop;
• carpenter's pencil;
• insulating tape.

Tools:

1. Protective gloves, goggles;
2. Saw or jigsaw;
3. Roulette, level, square;
4. C-clamps.

• Wear safety goggles when making cuts.
• Choose a blade with fine teeth.

Deadline

• 10 minutes

When installing a gas hob or hob, you must cut holes in the countertop.

Tip: Follow the manufacturer's instructions when cutting a hole in your kitchen countertop if you want to prevent potential problems..

How to cut a hole in the countertop for the hob

Guide line markings

The first step is to define the outline of the slab. In most cases, it should contain instructions on how to do this, but there is a technique in which only the recommended hole sizes are indicated. Place the hob on which is located on top of the cabinets. Leave the recommended distance from the back panel to the front edge of the countertop.

Draw a median on the countertop and mark the cut lines using the manufacturer's instructions.

Marking the countertop for the hole for the stove

As you can see in the picture, you need an L-shaped square, a tape measure, and a carpenter's pencil to get the job done professionally. Make sure the cut lines are parallel and at right angles. In addition, the rectangle must be symmetrical.

Tip: Check if the rectangle under the kitchen cabinet where the extractor will be built in is correctly positioned and there is enough space around it (according to the manufacturer's instructions).

Installing under-counter pads

To get an accurate result, you must place several spacers under the countertop. However, the tabletop must be level.

You must leave about 2 inches of space between the cabinets and the countertop, otherwise the saw blade could damage them.

Making initial holes for drilling

Use a drill with a special drill bit to create initial holes along the corners. It is very important to align the bits correctly, otherwise you may drill out of the contour.

Tip: Make sure you are using good RPM controlled drilling equipment. Set the drill at low speeds and hold the drill with both hands if you want to have good control over it. Repeat the process for each corner of the rectangle.

Passage of the laminated layer

In this image, you should notice that the drill is going through the top layer. Do not apply too much pressure to the drilling equipment or it may slide out of place.

We remove the residues from the process with a vacuum cleaner

Drilling a hole in the countertop with a drill will create a lot of residue, so we recommend that you have someone clean it up as you make the hole.

Tip: Work with great care and attention, as it is important to make holes exactly in the indicated places.

Starting holes for cutting in the worktop

After drilling the corner pilot holes, cuts must be made along the guide lines. If you are not experienced in this area, you should cover the cut lines with masking tape. In this way, you will help prevent chipping of the edges.

Cutting a hole with a jigsaw in a countertop

To make the cuts, we recommend that you use a jigsaw. Choose a blade with downward facing teeth. In addition, the blade must have set teeth. If you have not worked with a jigsaw before, we recommend that you fix the countertop. Make sure the blade goes exactly along the cut lines.

Tip: Clean up chips that form frequently, otherwise they may cover the lines. Set the jigsaw at low speeds.

Finished hole in the countertop for the stove

Last but not least, you need to take care of installing the hob into the countertop yourself. If you followed our advice and read the manufacturer's instructions, the hob should slide easily into the hole. However, if the edges aren't quite straight, you can smooth them out with silicone or caulk.

Tip: Use sandpaper to smooth out the cutting edges.

Installing the hob in the countertop

After that, you just have to install the hob into the countertop, connect it and secure it with the screws that should come with it.

Thank you for reading our step-by-step guide on how to cut a hole in your countertop and install your hob yourself, we encourage you to check out our other articles. Don't forget to share our projects with your friends using social media widgets.

Do-it-yourself installation of a hob is a test of strength for both a beginner and a seasoned master. The hob is an alternative to the overall kitchen stove. It performs the same functions, but takes up less space. Today we figure out how not to go crazy during the installation process.

How to install the hob yourself? Mandatory Installation Rules

As a rule, the product is mounted above the oven. A hole of suitable dimensions is made in the countertop and the device is placed on top. When every meter counts, can they be installed above the dishwasher or without a countertop?

Types of hobs

Gas

Electrical

Combined

The panel can be:

• gas;
• electric;
• induction;
• combined.

Each of them can be:

• dependent;
• independent.

The first include appliances that can only function in combination with an oven.

The control is carried out using a panel mounted on the cabinet - very rarely it is located on the hob.

IMPORTANT! Not all hobs and ovens can be used together. Sometimes even products from the same manufacturer are incompatible.

The second includes hobs, which require their own control panel. They are completely independent from the oven: this means complete comfort and placement in any corner of the kitchen.

This allows them to be placed separately, as opposed to being dependent.

Popular brands

The principle of installation from different manufacturers remains the same. Below we list the brands that will not let you down.

Model	Description
Electrolux EHG 96341 FK	Material: glass ceramic. Dimensions: 59 x 52 cm. Rated power: 6.6 kW.
	Material: glass ceramic. Dimensions: 60 x 51 cm. Rated power: 7.2 kW.
	Material: tempered glass. Dimensions: 10.2 x 73.3 x 50 cm. Rated power: 5.9 kW.
	Material: glass ceramic. Dimensions: 60 x 51 cm. Rated power: 6 kW.
	Material: glass ceramic. Dimensions: 59.5 x 51 cm. Rated power: 6.8 kW.
	Material: glass ceramic. Dimensions: 59 x 52 cm. Rated power: 6.5 kW.
	Material: glass ceramic. Dimensions: 58.3 x 51.3 cm. Rated power: 7.6 kW.
Midea MC-HF602	Material: glass ceramic. Dimensions: 59.0 x 52.0 x 5.5 cm. Rated power: 6 kW.

Proper installation: steps

electrical panel

Models with electric ignition made of glass ceramics delight with convenience. If the assembly is good, then the product will not require repair for a long time. However, if the surface breaks, detachment will be as simple as possible. It is quite possible to remove the electric cooker yourself and take it in for repair.

Let's start embedding. General algorithm:

• Place the electrical panel on the countertop, turn over and connect according to the diagram. For convenience, manufacturers place instructions on the back of the product. Connection requires care - in the event of an error, control of the burners and the heating temperature will be impossible.
• After that, you can turn the panel over and mount it in the hole. Check the operation of the inclusion and heating. The panel is completely ready to work.

The installation process on your own is not complicated. Especially for those who have ever done repairs or carried out construction work. Detailed algorithm:

1. Determine the dimensions. Please read the instructions before installation. It has a schematic drawing showing the dimensions of the installation and how to properly install the panel. This speeds up the process and minimizes possible errors during measurements and installation.
2. Measurements can be made independently. To do this, you need to turn the panel with the back side and, using a tape measure, measure the necessary parameters. Be careful: the installation depth is determined by the installation site.
3. Decide on indents. The instructions indicate the minimum indentation from the edges of the countertop, so we do not recommend making them smaller. This can cause damage to the edge and require repair. You can only increase the size.
4. Make markings on the countertop based on the measurements of the hob. To make installation accurate and easy, make sure the markings are stable. If you draw it with chalk, the lines will be erased, and this will create inconvenience during installation. We recommend sticking strips of paper tape, and already mark it on it.
5. Make a cut. At this stage, you need to drill a hole in the place where the cutout will begin. Using an electric jigsaw, cut along the contour of the top of the countertop. For a smooth cut, use a sharp file with fine teeth. Ideally, it is recommended to use a manual milling cutter, and rounding off the corners should be done with a milling cutter. In this case, the cuts need to be polished. After the procedure, sawdust is formed, which is better to immediately collect with a vacuum cleaner.
6. Try on the hob. Check the cutout and try on the panel. This will make sure that you can proceed to the next steps.

Step 1 - We mark on the countertop the place where the hob will be located

Sawing a hole

For installation, you will need an electric drill and a jigsaw. If they are not, then you will have to purchase or rent, because you cannot do without them.

IMPORTANT! The structure of the glass-ceramic surface is quite fragile, therefore, during installation, you need to be as careful and attentive as possible, as well as objectively assess whether it is worth doing the installation yourself or it is better to leave the matter to experienced craftsmen. If you still decide to do everything with your own hands, then move on.

When buying a hob, it will be convenient to make an individual order for the manufacture of furniture in parallel. You can simply tell the furniture makers the measurements of the device and they will make the cutout themselves. This is the easiest and most convenient installation method (then you can immediately go to the point of sealing / sealing).

Step 2 - Cut a Hole in the Countertop Step 4 - Place the Panel on the Hole

Sealing and proper sealing

To extend the life of the countertop and protect it from premature wear, it is necessary to use silicone sealant or nitro-varnish. This treatment prevents the ingress of moisture and dirt. Self-adhesive sealant (sealing tape) is also perfect for these purposes.

It is glued on top so that the edges of the built-in model lie on it. Aluminum tape is one alternative for sealing and sealing. This is the best option, as it protects the countertop from temperature extremes. Thanks to a high-quality seal, the product will last for many years without repair.

Step 7 - Connect the hob to the gas pipe. Depending on the type of built-in panel, the connection method changes.

gas hob

The instructions contain information on how the product is attached. Place the panel on the countertop, align it with the edge, then secure. As a rule, special brackets are included in the kit, with the help of which fastening is made. Then plug the electrical wire into the socket.

It remains only to connect the gas. First turn off the gas, and then connect the hob to the pipe using a flexible hose. Equip the nuts with paronite gaskets. You can turn on the gas. Make sure there are no leaky areas at the connection points. To test this, lather them with soap. There is no leak if the foam is not bubbling and vice versa.

If you have a gas analyzer, you can use it.

Socket for the hob: where to install?

Before installing the equipment, it is better to move the outlet under the countertop. This will provide maximum convenience in use and add aesthetics to the appearance - neither the socket nor the plug will be noticeable. It is also necessary to make a hole through which the wire will pass on the way to the electrical network.

IMPORTANT! If nevertheless marked out under the hob and oven, it is recommended to get a hood.

Step 9 - This is what the installed hob looks like

The idea of ​​installing a cooktop yourself can be a little intimidating. After all, you will have to deal with either electricity or gas and at the same time work with fairly expensive kitchen equipment. However, none of the steps for installing a hob are particularly difficult. You just need to do everything carefully and in the correct sequence from the very beginning to the end.

Steps

Installing an electric hob

Remove the old hob, if any. If you are replacing an old hob, you will need to remove it first. Turn off the electricity in the distribution box. Remove any attachments from the hob and clean off any sealant. Disconnect the wires, remembering how the old hob was connected, and remove the hob from the hole it sat in.

Make sure you have enough space in the location you have chosen for the hob. Ideally, you should have a gap of 76 cm above the hob, and on the sides of it there should be about 30-60 cm of free space. You should also make sure that there is enough space under the worktop to accommodate your new model hob.

Make sure that there is a junction box near the place you have chosen to connect the hob to the mains. Most electric hobs require a direct connection to the mains through a 220V junction box. If you are replacing a hobs, you probably already have a junction box.

Measure the dimensions of the hob and make sure it fits into the old hole. If you are replacing a hob, the countertop should already have a hole, and you just need to make sure it fits the new hob.

Adjust the hole for the hob so that it can fit into it. The hole should be on each side 1.5-2.5 cm smaller than the dimensions of the hob. If you don't already have a hole for the hob, or if it's too small, you'll need to cut it to size. If the existing hole is too large, then sheets of metal can be screwed on the sides to reduce it.

Remove all removable parts from the hob to make it easier for you to put it back in place. The hob may have removable burners, protective screens and other parts that should be temporarily put aside. You also need to remember to remove all packaging materials from the hob.

Install clamps. They are designed to fix the hob. You should hang them from the top edge of the slot and then screw them on.

Lower the hob into the hole. Lower the new hob into the hole, remembering to put the wires through it first. Press down on the hob until you hear the locking clips click.

Connect the wires of the hob to the mains. Electricity must still be turned off when you do this so as not to get an electric shock. Connect the hob wires to the corresponding wires in the junction box.

Install the previously removed detachable parts on the hob. Replace the burners, protective screens and other removable parts.

Turn on the electricity and check the operation of the hob. Turn on the power supply to the hob to check that everything is working properly.

Open all hotplates for a few minutes. Even though you have turned off the gas, there may still be gas in the hose. Open all burners to release the gas. Don't set it on fire. All the gas will come out in a few minutes.

Disconnect the flexible gas supply hose from the fixed gas line using two wrenches. Take one wrench and install it on the hose nut, and the second wrench on the fixed gas line nut.

Remove all removable parts from the hob. Remove burners, protective screens and other removable parts before moving on. This will make it easier to move the hob.

Remove the clips holding the existing hob in place. Unscrew the clips from the underside of the old hob.

Push the hob from below to lift it up. Remove the hob from the countertop and put it in a safe place. Don't forget that the gas hose is still attached to it.

Disconnect the gas hose from the old hob. If you will be using the old gas hose to connect the new hob, you will need to disconnect it from the old hob. Use two wrenches for this, one on the hob and one on the hose nut.

• To disconnect the hose, turn its nut counterclockwise.

1. Connect the gas hose to the new hob. Use a gas joint sealant by applying it to the threads at the junction of the hose and the hob. Apply sealant generously to the threads, but be careful not to get it inside the hose. Screw the nut of the gas hose to the hob using a wrench.

   Place the new hob in its place. Carefully lower the hob into the opening so as not to damage any of the connections at the bottom of the hob. Before lowering the hob into the opening, you must lead the gas hose forward into it.

   Connect the gas hose to the fixed gas pipe. Apply sealant to the threads of the gas pipe fitting. Then tighten the gas hose nut with a wrench. Be sure to tighten the nut tightly.

   Prepare a soapy solution. Prepare a solution of 1 part dish soap and 1 part water to check for possible gas leaks. Stir the solution thoroughly and then either spray it on the gas connections or apply with a brush. Turn on the gas supply valve by placing it in a position in which its handle indicates the direction of gas supply.

   Turn on the burners and check their operation. If the soapy water test reveals no leaks, try lighting the burners. It may take a few seconds for the gas to come up and ignite, because normal air must first exit the hose.

2. Attach the hob mounting brackets to the worktop. When you are sure that the hob is working, attach it with mounting brackets to the countertop. Your hob is now fully installed.

   • Replace the doors and drawers of the cabinet under the hob, as well as all its contents.

Cooktops save space in the kitchen, and they work just like bulky stoves. In addition, the installation of the hob is completely easy, it happens quickly enough, and any adult can handle it with certain tools.

For those who started repairs in the kitchen, it is possible to replace the stove with a surface. You can also make a combination of a surface and a separate oven, and in this way you will not lose anything.

Sawing a hole

If you have ever done repairs in the house or were engaged in some kind of construction work, then the process of installing the hob in the countertop should not be difficult for you. So, let's begin.

1. To install the surface in the countertop with your own hands, you first need to know its dimensions. All the necessary dimensions are indicated on the diagram in the instructions, you do not need to invent anything. This speeds up work and significantly reduces the chance of measurement errors. Measurements can be made with your own hands by turning the panel over and using a tape measure to determine its width and length along the inner edges.
2. Please note that the instructions indicate the values ​​\u200b\u200bof the minimum indents from the edges of the tabletop. You can only change them in a big direction, since an edge that is too narrow may break off over time.
3. Make markings on the countertop, according to the dimensions of the hob. This is where she will fit in. In order for the lines not to be erased and to be better visible on a dark surface, glue strips of paper tape and transfer the lines to it.
4. Next, drill a hole where the cutout will start from. The cut is made with an electric jigsaw. To make the cut even, not crumble, it is recommended to use a file with fine teeth, not blunt. It is even better to use a manual router, round off the corners with a radius cutter, and grind the cuts.
5. The resulting sawdust can be collected with a vacuum cleaner.

When the hole is ready, try on the hob to make sure everything is done correctly.

Sealing and sealing

Treat the sections with silicone sealant or nitro varnish. This will protect the countertop from dirt, wetting, swelling and premature damage. You can also use a self-adhesive seal that performs the same function. It is glued on top so that the edges of the panel lie on it.

Even for edge seals, you can use aluminum tape, which, among other things, will protect the countertop from temperature changes. Having a quality seal will ensure that your countertop will last a long time and won't need to be repaired or replaced.

Connecting the electrical panel

Modern electrical panels are very convenient, with good assembly they rarely fail, which means that they will not need repairs for a long time. If, nevertheless, repairs are required, then the panel can be easily disconnected and taken to the workshop on its own, thereby saving on calling the master.

Before embedding an electrical surface, it is necessary to lay it on the countertop, turn it over and connect it according to the diagram. The diagram is shown directly on the panel on the back for your convenience. When doing this procedure on your own, be careful. If the wires are connected incorrectly, you will not be able to control the activation of the burners and the heating temperature.

If a separate wire from the shield is provided for connecting the electric hob, then the plug and socket are not needed. Just connect the wire to the panel.

Flip the panel over and install it into the hole. It is already ready to work, it remains only to check whether it turns on and heats up correctly.

Connecting the gas hob

When installing a gas hob, first look at how it is attached. Install the panel, align it with the edge of the table and secure. Usually, brackets are provided with the panel for mounting from below. The electrical wire must be plugged into an outlet.

To connect the gas with your own hands, you need to know the safety rules. Shut off the gas and connect the hob to the pipe with a flexible hose. Be sure to put paronite gaskets in the nuts. Turn on the gas, turn on the burners and check the hose connections for leaks. To do this, they need to be lathered. If the foam does not bubble, then there is no leak, you did everything right. You can also use a gas analyzer to check.

Many years ago, kitchen sets did not represent the possibility of mounting a hob in them. Today, this is a common phenomenon, which saves space in the kitchen, and also makes cooking more convenient and comfortable. Installing the hob in the countertop can be done independently. The main thing is to correctly determine the sequence of actions and follow it. It is very important to correctly determine the size of the future opening.

Modern technologies do not stand still. Today it has become possible to integrate hobs into kitchen sets, which qualitatively affects the interior of the kitchen and its functionality. Inserting the hob does not take much time.

First of all, on the countertop, you need to make a markup that will fit the size of the hob.

Next to each side of the niche, you need to drill a hole, the diameter of each should be from 8 to 10 mm. The next step is to cut out the niche and treat it internally with silicone. The tabletop is installed on the lower level of the headset. The inside of the panel is attached with double-sided tape or a little plasticine. The tabletop is covered with silicone.

Step by step installation:

1. The tabletop is placed on the bottom of the headset. If the walls are uneven, the countertop will need to be trimmed. And if gas pipes pass through it, special holes must be made for them. The countertop should be ready for installation down the kitchen.
2. Inside the box in which the hob will be installed, it is necessary to make markings. To do this, you can simply make pencil outlines that will help you make further markup.
3. The tabletop is laid face down, and markings are made on the reverse side for a future tie-in.
4. In each intended cut, small holes must be made so that you can work with a jigsaw.
5. Carefully cut out the niche with an electric jigsaw.
6. You need to make sure that the tabletop does not deviate under its own weight. In the process of cutting, it is better to carefully support it.

The inside of the cut is treated with silicone. After installing the panel, you can additionally coat it with silicone from the outside. This is done in order to create an additional hydro-barrier, since the fasteners may not be pressed against the countertop enough.

The gas hob must be chosen very responsibly, because it should last for many years. After the choice is made, the panel must be installed so that it is convenient and safe to use. You can embed the panel yourself, but you should not do this if you are not confident in your abilities. In any case, you can contact a specialist for help.

When installing it yourself, it is important to prepare all the necessary materials: panel, measuring instruments, pencils, sealant, adjustable wrench, saw, gas winding, steel hose.

All work related to gas is unsafe to carry out. It is best to perform the installation together with a wizard or someone who thoroughly knows the entire installation process. One of the most important stages of installation is the choice of hose.

Hose Selection Tips:

• Check hose for damage. There should not be a single defect on the hose.
• The hose must be certified. When buying, you should ask the seller to present all the documents for the goods.
• The hose can be corrugated metal or rubber.

When installing the panel, the calculation of dimensions must be given special attention. Sometimes in the kit for the hob you can find a template that you need to use in order to properly saw through the countertop. It is important to remember that water should not get on the surface of the panel. The gas countertop must be placed at a safe distance from furniture and textiles.

How to install the hob in the countertop

The built-in electric stove is a very convenient device for installation in the kitchen. It works just as efficiently as a stationary stove, but does not take up as much space. Installing such a panel can be quick and easy, without resorting to the help of specialists. The surface can be combined with an oven, which will make cooking even more convenient.

If the master does not carry out independent repairs for the first time, then installing the hob will not cause difficulties.

Before installing the panel, you need to properly cut a hole in the countertop. To facilitate the installation work, manufacturers indicate the required dimensions in the instructions for the device. Pre-marking greatly simplifies and speeds up the installation process.

Installation steps:

• On the countertop, you need to make markings that will correspond to the dimensions of the panel.
• Using an electric jigsaw, you need to make a cutout in the countertop. To get started, you need to drill a small hole for a jigsaw. The cut will be even if you use a jigsaw file with fine teeth.
• The dimensions of the hob must match the cut hole. Sections must be treated with a sealant or nitro-lacquer. Sealing self-adhesive tape can be used for processing.

The electric tabletop is connected, focusing on the diagram. It can be found on the back of the panel. It is important to connect the wires correctly in order to be able to control the activation of the burners and their temperature.

What to look for: fixing the hob to the countertop

The installation process of the hob is simple, but requires careful preparation. First of all, it is tedious to choose the right hob, check its passport data, prepare the tools and decide on the installation location. The installation of a gas and electric hob is practically the same.

You need to mount the panel on the countertop, in which you need to make the appropriate cutout.

It should be noted that to install the electrical panel, you will also need to install an electrical outlet. For a gas panel, care must be taken to carry out gas communication. The built-in panel must be installed so that the maximum gap between it and the worktop is 1-2 mm.

What to look for:

• Correctly measure the dimensions of the panel and transfer them to the cutout in the countertop.
• Cut out the necessary segment in the countertop in order to perform the installation correctly.
• Treat the countertop with special materials that will protect it from the effects of external negative factors.
• Push the panel into the cutout.

It is important to remember that the mortise panel should not enter the gap with force. If there is a backlash, the location of the countertop must be aligned, focusing on the front edge. Fastening the seal over the entire surface of the countertop will avoid contamination of the panel.

hob seal

The sealing gasket must be attached to the hob. If the panel is removed after some time of use, you will notice that the seal will be covered in dirt and grease. The gasket needs to be replaced from time to time.

If there is a gap between the panel and the countertop, then the plate can be fixed in the plane, but this must be done so that debris does not fall into the vertical gap.

You can buy a special tape, or you can use a glass seal. The table and cutout can be pretreated with a transparent sealant. Sealant residues must be wiped off or carefully removed with a spatula.

Benefits of sealing tape:

• Reliability;
• Ease of use;
• Environmental friendliness.

Bosch seals are known for their high quality. Just placing a panel is not enough. It must be protected from moisture, grease and debris. If the panel is installed in a large opening, and a gap is formed, then the tape and the treatment of the gaps with sealant will help save the situation.

Installing the hob in the countertop (video)

The built-in hob is a convenient device that saves space in the kitchen and provides comfortable cooking. The rules for installing the panel are simple, so you can install it yourself. It is possible to embed a panel qualitatively only when the dimensions of the panel are measured correctly. After cutting a hole in the countertop, it must be well treated with sealant to protect the panel from water and dirt. All actions should be phased and coordinated.

Return