Tomato stakes made of fiberglass reinforcement. Practicality and economy: fiberglass reinforcement in the country

From this article you will learn in what ways you can tie up tomatoes in the greenhouse and in the garden.

To grow vegetables at home, you need to know all the details about each vegetable separately. In this article we will learn how to tie up tomato bushes and whether it is necessary to do so.

What are the modern methods and options for gartering tomatoes, and what can be used for gartering?

Garter of tomatoes to a trellis

We have already planted the tomatoes, and they have taken root; in order to have something to tie the bushes to, we need to drive wooden pegs or metal rods into the ground. Methods for gartering tall tomatoes there are:

An individual peg for each plant, the height of the length of the plant, plus 25-30 cm for driving into the ground
To the trellises
To linear trellises
Construction of a cage for each plant
Construction of pyramidal or triangular caps for 3 or 4 plants at once
Attaching the plant to the wire using hooks and rings

We installed pegs or other devices in the ground, and we will tie the plants to them. Suitable for garter:

Strips of fabric, 3-4 cm wide
Nylon tights or stockings
Soft rope
Plastic clips

Note. All thin and hard garter materials are not suitable - they can cut into the branches and trunk of the plant and destroy it.

Cannot be used:

Fishing line
Wire
Threads
Thin and tough rope

Important. If you take last year's garters, then before using them, you need to wash them with laundry soap to kill bacteria.

How to buy pegs, fiberglass reinforcement, plastic clips, stapler, device for gartering tomatoes in Aliexpress: links to the catalog

If you don’t have pegs or binding material, you can buy them at any time of the day in the Aliexpress online store, and. There is a wide range of products for gardening.

When and why should you tie up tomatoes in a greenhouse or open ground?

To get a high yield of tomatoes, you need to learn how to properly care for them, including tying them up. Tall varieties are tied up, and low varieties with a bountiful harvest. They are most often planted in greenhouses, less so in open ground.

Experienced gardeners advise tying up all low-growing varieties, because this way you can get a much larger harvest.

Tomato garter needed:

To make it easier for plants to support the weight of the fruit, otherwise they may break.
Tall tomatoes with fruits, if not tied up, will lie on the ground and rot or be eaten by pests, and to prevent this from happening they need to be tied up.
Tethered plants are easier to pinch (remove additional shoots that may bear fruit).
It is not advisable to pour water on the leaves and set fruits, and therefore you need to water the plants closer to the roots, and this is easy to do with tied tomatoes.
It is also easier to fluff up the soil around the tomatoes if the plants are tied up.
A plant positioned vertically receives more sun and air, and therefore the fruits will ripen faster.

Important. We begin tying up tomatoes 2-3 weeks after planting the seedlings in open ground or a greenhouse.

How to properly tie tall tomatoes in a greenhouse and open ground: 5 methods, rules, tips for beginners

Tying tall tomatoes

Some varieties of tall tomatoes grow up to 1.5-2 m tall. The stakes should also be of the same height. In open ground, plants of this height are planted approximately at a distance of 1 m. And they need to be tied up as they grow, 3-6 times per season.

There are 5 main ways tying up tall tomatoes:

Tying up to the pegs plants using fabric strips or soft rope.
Construction wire frame, cone-shaped, around the plant. The method is expensive if there are a lot of tomato bushes.
Tying tomatoes to the horizontal trellis. This is done like this: we drive high stakes along the edges of the bed with tomatoes. We stretch the wire between the stakes, starting from the bottom and up, every 30 cm. First, we tie the plants to the bottom wire, then, when they grow up, higher.
Tying tomatoes to the vertical trellis. This method is only suitable for greenhouses. We stretch a wire along the ceiling of the greenhouse, and the tomatoes are tied to it.
Tying tomatoes to the grid. We install a metal mesh between two posts and tie tomato bushes to it.

In the garden, you can tie tomatoes using all methods except 4, and in the greenhouse you can use 3 and 4 methods of tying.

How to properly tie up low-growing tomatoes in a greenhouse and open ground: 5 methods, rules, tips for beginners

Low-growing tomatoes in the garden can be tied, or they can be left to grow without support. Each case has its pros and cons. If plants grow without support, they take additional root, and the fruits on the ground can rot from moisture. So, experienced vegetable growers advise tying up low-growing plants. This can be done as follows ways:

The most popular method for low-growing tomatoes is tying to the posts, about 1 m high. We drive the posts into the ground 5-10 cm from the plant. We wrap the plant and the post with a strip of fabric or a soft rope in the shape of a figure eight, and tie the ends of the rope to the post, like a bow. The rope should be tied loosely and not cut into the plant.
Tying bushes to a low trellis. We drive low stakes, about 1 m high, along the edges of the bed with tomatoes. Attach a thick wire to the stakes on top. We tie each bush to the wire with a soft rope.
Devices in the form quadrangular cap. Around 4 tomato bushes we hammer 4 low pegs, which we wrap with wire: at the bottom, in the middle and at the top. The wire will support the bushes and then the fruits.
Devices in the form triangular cap. Near each bush we drive pegs into the ground and wrap wire around them in several places. The bushes are obtained in the middle of the triangle.
Net, about 1 m high for tying tomatoes. At the beginning and end of the bed with tomatoes we hammer in 2 columns. We attach a net to them, to which we tie the tomato bushes.

Video: How to tie up tomatoes? An easy way using a plastic bottle

How to properly tie tomatoes to pegs in a greenhouse and open ground: description of the method

In the garden, for gartering tomatoes, we first install pegs to each bush. They can be wooden or metal. We drive the peg into the ground 5-10 cm from the plant. It must stand firmly. With a soft strip of cloth or a soft rope, we wrap the peg and the plant in a figure eight several times and tie it to the peg, without pulling the plant to it, but so that there is free space and the plant can grow.

Video: How to tie up tomatoes in open ground

How to properly tie tomatoes on a trellis?

Tall tomatoes are tied to a trellis

We install trellises for tying tall tomatoes in a greenhouse or in a garden. This is done like this:

Along the bed with tomatoes, we drive iron stakes into the ground, about 2 m high, every 1.0-1.5 m.
Between the stakes, from the very bottom to the top, at a distance of 35-40 cm, we stretch a thick wire.
We tie each plant with a soft garter to a wire.
In addition, as they grow, we tuck the branches behind the wire.
When the fruits grow, we also tie them to the wire, or hook them to the wire.

Using this method, you can leave additional branches on the plant; the support is reliable and will withstand everything, and besides, the harvest will be larger, and in the greenhouse it’s not scary if frost starts.

How to properly tie tomatoes in a linear way?

Tomatoes tied to linear trellises

The linear method is used in the greenhouse and in the garden:

We drive stakes 2 m high in a straight line along the bed with tall tomatoes.
We stretch a strong wire at the top between the stakes.
We tie one end of a long soft garter on the plant at the very root, and tie the other end of the garter at the top with a wire.
We tuck the growing branches behind the garter and direct them upward.
We also tie large fruits to the wire.

How to properly tie tomatoes on hooks and chains?

Garter of tomatoes on hooks

The method of tying tall tomatoes on hooks is similar to tying them on trellises. Along the edges of the bed with tomatoes we bury 2 metal stakes, about 2 m high. We stretch the wire between the stakes. We tie a fishing line with a loop to the wire above each bush, and attach hooks to it. We cut the bicycle inner tube into thin rings. We thread the ring under a branch of the plant, bend it in half, and hook it to the fishing line. Hooks can be made from aluminum wire or bought in the online store.

How to properly tie tomatoes in a cage?

Garter of tomatoes in a cage

One way to tie up tall tomatoes is to build a cage for each tomato. We make the cage from 4 pegs; wooden or metal ones are suitable, depending on the height of the plant. We hammer the pegs around the plant and connect them together with wire in 3-5 rows at different heights, to which the plant is attached using a soft rope. We attach the grown plant higher to the wire.

How to properly tie tomatoes without stakes?

Tying tomatoes without stakes

In this method of tying tomatoes, stakes are still needed, but not for every bush. This is done like this:

We plant tomatoes in 1 row.
We hammer in 3 pegs on both sides of the row with tomatoes, the middle peg on each side is higher, and there are low pegs on the edges.
We connect the pegs around with a soft rope, it will act as a limit for the bushes.
In addition, we also connect high pegs with rope or wire at several levels in order to tie tomatoes to it.

How to properly tie tomatoes in a figure eight in a polycarbonate greenhouse?

Tying tomatoes in a polycarbonate greenhouse

The polycarbonate greenhouse is tall, it is heated, and in it you can grow tall tomatoes all winter long. You can tie them to trellises in a simple way - in the form of a figure eight or, as people say, with a bow. First you need to tie the rope to the plant loosely so that there is free space near the trunk, and then tie the rope to the wire at the top without pulling it.

A polycarbonate greenhouse is large, and there is a lot of work in it; to simplify the work, you can purchase a special device similar to a stapler from an online store. The device works by tying the plant and the wire with a special tape and fixing them together. This way you can quickly tie up all the branches in a short time.

What is the easiest method for gartering a tomato?

The easiest way to tie tomatoes is to a peg

The easiest method for staking tomatoes is to stake each tomato. It can be wooden, metal or a piece of pipe. The height of the peg should be no less than the height of the tomato when it is fully grown, and about 30 cm additional for driving into the ground.
We drive the peg 5-10 cm further from the tomato bush. Then we lightly wrap the garter around the plant, twist the ends and attach it to the support. When the tomato grows, we tie it higher with another ribbon, or remove the one that was there and tie it higher.

This peg and garter method is only suitable for medium-sized tomatoes; a plant belonging to tall tomatoes may not be able to withstand such a peg, and the structure along with the plant will collapse.

How the Chinese tie tomatoes: a description of the method

The Chinese have developed many drought-resistant tomato varieties that have proven themselves well in our country. Chinese technology for growing tomatoes also appealed to those gardeners who came across it. The Chinese's tying of tomatoes is also very original and fast. It consists of the following actions:

We plant tomatoes in a row with a distance of about 20-30 cm between them.
We hammer pegs between the tomato bushes.
We place the bobbin with the rope in our backpack.
We take 1 peg and drill a hole at the end of it so large that the rope can move freely.
We pass the rope through the hole in the peg that we have in our hand.
On the first peg, standing at the beginning of the row, 10-20 cm from the bottom, we tie the end of a soft rope.
Then the plants will be tied up automatically: we walk at the usual pace and direct the stick with the rope first to the bush, then to the peg, wrap it around it; We make movements with a stick as if weaving a basket. So we reach the end of the row of tomatoes.
Then we return, but now the rope should lie on the other side of the bush.

Video: Garter of tomatoes. Pro

How to tie up Bull's Heart tomatoes in a greenhouse and open ground: features, tips

Bull's Heart tomatoes

Tomatoes "Bull's heart" are tall. As seedlings, in a garden or greenhouse, we plant them at a distance of about 0.5 m, one plant from another. It is good to tie them to trellises with soft rope. Thick wire can be used as a trellis. The wire is attached to two iron stakes. We tie a rope to each bush at one end, and tie the other end of the rope at the top to a wire.

When the plants grow up and fruits begin to set, they also need to be tied to a trellis, otherwise the plants may not be able to withstand the heavy weight of the fruits, because one tomato of this variety sometimes weighs up to 0.5 kg.

How to tie cherry tomatoes in a greenhouse and open ground: features, tips

Cherry tomatoes

Cherry tomatoes can be grown in the garden and greenhouse. Cherry bushes are low, medium and high in height, depending on the variety. Low and medium-sized cherry trees do not need to be tied up, but tall cherry varieties can reach 2 m in height.

When cherry seedlings, planted in a greenhouse or garden, reach 30 cm in height, you need to install supports. Metal rods or, if there are a lot of plants, trellises are suitable for supports. Cherries continue to grow and need to be tied higher and higher.

In addition to eating them, you can decorate your balcony with cherry tomatoes if you buy decorative cherry tomatoes. We plant these tomatoes on the balcony in a hanging basket; when the fruits set, they will hang down beautifully, and so that the branches do not break off under the weight of the fruits, we will stretch a wire along the balcony and attach the branches to it.

How to make sticks and supports for tomato garters with your own hands?

Pegs for gartering tomatoes can be made from the following materials:

Thick tree branches
Wooden boards
Long wooden planks
Metal rods
Long pieces of metal pipes
Strong plastic sticks

To make it easier to drive into the ground, we trim the wooden stakes with an ax on one side. Metal rods and pipes are more difficult to install and require skill.

How to treat pegs for gartering tomatoes?

Tall wooden sticks are suitable for pegs. To prevent them from rotting by the end of the season, they need to be slightly burned over a fire or in an oven. Pegs treated in this way will be suitable for tying tomatoes for several years.

Do I need to tie up tomato bunches?

Tied bunches of tomato

Tomatoes of large varieties, such as “Oxheart”, need to be tied with a rope or hooked, otherwise the branch may not hold up and break. Some gardeners make their own hooks from wire and attach them to a branch to the trellis. But you can also order ready-made hooks in the online store, or.

What happens if you don't tie up tomatoes?

Tied tomato bushes bear fruit better

Tomatoes can be left untied in areas with a hot climate, even if they are low-growing. There the fruits lie on the ground, the days and nights in the southern countries are warm, they ripen quickly and do not have time to rot. But tall tomatoes will have to be tied up in subtropical countries.

And in temperate latitudes, where it is often cold for tomatoes at night, lying on the ground, they rot, they are eaten by pests, and so you can lose the entire harvest. Therefore, you need to tie up both low and tall tomatoes.

So, we learned how to tie up low and tall tomatoes, in open ground and in a greenhouse.

Video: Tying up tomatoes! How to properly tie tomatoes in a greenhouse and garter errors

Hello, dear summer resident!

In this summer season, In the spring of 2017, I sowed new low-growing varieties of tomatoes for seedlings and even then I was thinking about replenishing the supply of pegs for tying up tomato bushes, but I could not decide on which specific pegs and, most importantly, what material to buy in addition to the existing metal pegs.

I went to the country shops, I looked at the metal pegs, but they were very expensive. Judge for yourself, 10 metal pegs cost 1,500 rubles, but I need not ten pegs, but, for example, 40-45 pieces. So it turns out that you need to shell out a tidy sum from the family budget.

My wife and I have this option, Naturally, it didn’t suit me even then... His Majesty’s chance helped, as happens in many cases!

I once went into a hardware store, I examined the offered range of goods, but did not find anything suitable as pegs. Then I decided to ask the seller if they had anything that could replace metal pegs for tying tomatoes?

The seller, without thinking twice, leads me to a twisted coil of something light and rebar-like (with a ribbed surface) and says that this is an excellent option for pegs. The cost per linear meter was 40 rubles, diameter 10 mm.

There were 50 meters in the twisted bay, which means that if you cut the pegs one meter at a time, you will end up with 50 pegs. Of course, this interested me, but I had no idea what this fittings were made of.

The seller explained to me, that it is an alloy of glass and plastic and this material does not bend or break and is used for concreting foundations and other concrete work, as an alternative to metal reinforcement.

I told the seller that you need to think and weigh everything, and just shell out 2000 rubles. for “no one knows what”, I do not agree. Arriving at the dacha, I started a conversation with my neighbor, and she told me that such fittings went on sale last year and were made not far from our city of Lipetsk.

The neighbor was also looking an additional number of pegs for tying up our tomatoes, and we decided to find out in more detail about the properties of this reinforcement, whether it can really be used as supports for low-growing varieties of tomatoes, and then buy it.

Well, we talked and talked. I was minding my own business at the dacha, and my neighbor needed to go to the city for groceries (she lives at the dacha all summer) and take care of her other affairs.

In short, A couple of hours later, the neighbor returns from the city and calls me to admire her purchase. She opens the trunk of her car (she has a Lada-four), and there is already a roll of fiberglass reinforcement with a diameter of 8 mm, the price per linear meter is 23 rubles. (standard length of a solid rod is 50 meters).

So as not to upset her too much I gently hinted that she was in a hurry to buy such thin fittings, since she had to buy at least 10 mm in diameter, because this thing is bought once and, perhaps, for the rest of her life, but the job was done.

And the situation with diameters here is like this. Based on the external twisted conductors, it turns out to be 8 mm, and the round timber itself (the body itself) of the reinforcement has a diameter of 6 mm, therefore, both in appearance and, in fact, this diameter of the reinforcement looks flimsy and unreliable.

Here, judge for yourself. The pegs themselves, cut one meter at a time from a whole cane, are strong, but their task is to hold the tomato plant in an upright position. But if the tomato variety is very productive, and, God forbid, there are strong winds during the summer season, then the reinforcement may not withstand such a load and fall to the ground along with the bush?

No, it's fiberglass itself it will not break, bend or crack, but simply will not stay in the soil of the plot under such a load of the bush and will collapse.

Based on these considerations, I bought a bay (50 meters) of this fiberglass reinforcement with a diameter of 10 mm. I bought it not in the store where I first saw it, but in a building materials store on the way from home to the dacha.

And, by the way, linear meter in this store it cost me 32.5 rubles. After the purchase, the seller immediately warned me that unwinding the entire whip from the twisted coil must be done carefully and it is better to do this together, since the reinforcement itself is rigid and immediately straightens.

And if you remove all the twists of wire at once, with which the twisted whip is fixed, then no matter the hour, you can get it in the teeth. Here, in short, I bought such a bay of fiberglass reinforcement (see photo)...

Where to unwind this bay? After all, 50 meters is not that for you...

In short, My wife and I decided to carefully unwind all the whip along the garages. There are no people here and there is plenty of free space. Oh, and my wife and I suffered a lot of fear while unwinding this “wheel”.

And the point here is that when we removed one wire twist and freed one end, the whole whip, like a clock spring, tried to escape from the hand and straighten out as it pleased.

If it weren't for our four hands, with which we slowly and carefully intercepted one by one along this “wheel”, spinning it one centimeter at a time, we would definitely get hit in the teeth.

But everything went without injuries, the whip lay quietly along 11 garages, and all I had to do was mark out this whole “sausage” one meter at a time with a marker and saw down these pegs.

I sawed this material an ordinary hacksaw with a metal blade. It felt like a knife was cutting butter—the material was being sawed without any effort or strain. And by the way, the length of the whip turned out to be not 50 meters, but 50.5 meters (half a meter extra).

Then I brought these pegs to the dacha, and wanted to immediately insert them next to the tomato bushes, but noticed that on both twisted veins that encircle the “body” of the reinforcement, there was “pubescence” shining in the sun.

You know, like before, if someone worked with glass wool, then after this work all their hands seemed to be covered in glass “needles” and then the body itched from these “needles”.

No, there was no such effect here, since these “needles” were soft (I tried them with my fingers), but, just in case, I still decided to go through these twisted veins with sandpaper, so that in the future there would be no, God forbid, incidents with these “needles” .

After I sanded each peg, I washed them in a bucket of water and laid them out to dry. No, of course, it was possible to immediately insert pegs into the soil next to the bushes, but I approach each job thoroughly and slowly.

The end result of the work there must be not only competent execution, but also beautiful execution.

Not understood, what I'm talking about?

It's simple. You need to stick the pegs in so that their tops are at the same level - this way the whole tomato plot will look much nicer than how these tops will be at different levels of the horizon.

Well, is it true or not?

That is why, After the pegs had dried, I laid them out on the armrests of old chairs, aligning them along the length and marking 25 cm with a marker. This is exactly the length I was going to stick these pegs into the soil, and 75 cm remains above the soil.

For anyone who is more or less short, and a medium-sized variety, this height of pegs will be just right. I then inserted these pegs into the soil of the tomato plots.

And so that you can compare, Whether there will be a negative effect from fiberglass pegs or not on the tomato plants in two adjacent plots with the “Unknown” variety, I used pegs made of different materials.

Here is one plot with metal pegs with the variety “Unknown”...

Second plot of the same variety with pegs made of fiberglass reinforcement...

Here is a plot with the variety “Roma VF”, in which one bed is with metal pegs, and the second is with fiberglass pegs (see photo below)…

And this is a whole plot with only fiberglass pegs, variety “Snow Tale”….

As of June 24, the situation is for the worse has not changed and this is already pleasing. Here are photos from this period.

These are two plots with the “Unknown” variety...

Here's a photo a little closer. Look what branching bushes are growing this year... it’s a pity to even pluck them...

These are photos of a plot with the variety “Roma VF”...

This is a plot with the “Snow Fairy Tale” variety...

This is from one side...

This is from the other side...

And so, at the end of this season it will be possible to judge the effect of fiberglass pegs on tomato plants.

If the result is neutral, i.e. there will be no negative impact for the plants, then I will buy another bay of this fittings, since next year I plan to increase the number of tomato plots.

Well, off to the road...

The wife is surprised and happy tomato plants of the “Snow Fairy Tale” variety - they stand like small oak trees! This is the first year that this variety has been growing at our dacha, but I myself am amazed at its power of growth and development.

The wife doesn't even suspect that I have already fermented and applied 8 baths of my infusions of EM-elixir and poured them over the mulch under the plants (I haven’t sprayed them on the leaves for diseases yet) and tomatoes, and apple trees, and currants with gooseberries, and honeysuckle, and onions, and garlic, and potatoes, and carrots, and grape bushes, etc.

Perhaps in July I will start spraying with Elixir and on the leaves of all crops, so as not to give diseases a single chance to “raise their heads,” otherwise our rains do not stop and the air humidity is very high.

And here comes another rain...

See what a positive effect To control diseases on all crops, spraying with Elixir was carried out in the past 6 years, starting in 2011. Oh, well, that's the same. Can I offer you information that I myself have not used and tested in practice?

I have this principle– try it yourself in your practice, and then, if there is a positive result, you can offer it to people. I don't suggest a "pig in a poke".

Here are some photos of the bath with infusions of EM-elixir at the dacha (look at the shooting date)…

They turned out a little different in color, but the ingredients are the same...

I spilled this particular infusion tall tomatoes in plots near the fence and against the walls of the barn...

One plot near the fence...

East wall of the barn...

South wall of the barn...

The western wall of the barn...

The second plot is near the fence...

The infusion was scooped out to the bottom... and immediately fermented a new one...

Here, in a couple of days the infusion is ready (you see a film on the surface of the water - that means the infusion is ready!)...

I used this infusion and fermented a new one...

And I used this infusion for watering under the bushes currants, gooseberries and honeysuckle...

I haven't used this infusion yet...

If anyone doesn't have my materials yet for the fermentation of reliable and high-quality infusions of EM-elixir, then you can place an order by delivery in Russia on my website - http://elicsir.dacha7.ru/

Who will need the electronic version? these materials (so as not to get confused with the mail) or who has the opportunity and desire to pay for your order using my Sberbank card, write to me at this email address - [email protected]

After receiving the material, Make the first starter immediately and use it on your plants in a couple of days. The weather is warm, so the infusions mature quickly.

And every year your plants will be less affected by fungal and viral diseases and will delight you with a delicious and environmentally friendly harvest of vegetables, fruits and berries!

And the last thing...

Now I have the following questions for you:
« you used pegs made of fiberglass reinforcement?
If yes, was there any negative impact for tomato plants towards the end of the season?
If not,“Are you planning to use this reinforcement as pegs for tying tomatoes, peppers and eggplants?”

Your questions, suggestions and wishes, write in the comments to this post.

And that's all for today, Goodbye.

Best wishes,
Sergey Dyakov.

Country houses, territory design, garden and vegetable garden, as well as many other factors require us to spend certain expenses. Today we will try to significantly reduce them by using only one material - fiberglass reinforcement, and at the same time we will not lose an ounce of quality!

When we come to our summer cottage, we assess the situation every day... it’s time to pull down the house, build a new shower and makeshift shed, put a greenhouse on the right, and plant tomatoes in the garden on the left. There are thousands of such solutions, but each of them depends on free time and financial costs, and if we can find time to work at the dacha at least on a day off, then money does not come to us so easily once a week. There is only one thing left to do - save on buildings, decoration, and growing some plants. But in order not to limit yourself in the dacha business, to continue to build and achieve maximum results, it is not at all necessary to abandon objects or part of the garden; you can always choose related materials for supply, which will cost a little less.

Today we decided to study such a material as fiberglass reinforcement. This is a high-class building material with considerable demand, which can be safely used in the countryside. Thanks to its characteristics and positive qualities, it can be used almost everywhere, which will immediately reduce a certain type of cost by 15-30%. So, let's go into more detail, because the topic is quite interesting!

What is fiberglass reinforcement

This is a unique building material, which is not much different from steel reinforcement in terms of external data, but from a technical point of view, it is a serious competitor. The base consists of fiberglass and polymers. The inner part of the reinforcement is a strong set of fibers that are bound together with polymer resins, the outer part is an array of the same fiber that runs in a spiral along the entire length of the rod.

Thanks to well-established production, today it is possible to choose a material for construction or decoration as an alternative to steel structures, which are simply not suitable for many country works. Moreover, the option we propose is cheaper than steel, it is easier to install, and you do not need expensive equipment or the skills of a craftsman to work.

Advantages and disadvantages of fiberglass reinforcement

It’s worth immediately evaluating the material from both sides so that you can understand how suitable it is for certain work in the country. Among the huge number of advantages and disadvantages, we decided to indicate only the most significant!

Advantages of composite reinforcement in the country

The material can be used in many areas - construction, gardening, creating small architectural forms, auxiliary elements, structures to increase comfort and practicality in the country.
The material's tensile and tear characteristics are 3-4 times higher than those of its steel counterpart.
The material is durable and can last 80-100 years.
Neutral to the effects of alkalis, moisture and acids.
Wide temperature range of application, from -70°C to +100°C.
The reinforcement does not corrode and does not oxidize inside structures.
The composite material has an expansion rate close to concrete, and therefore eliminates cracking of foundations when laid correctly.
The material is a dielectric, which is very important in summer cottage construction.
Can be supplied in pieces of the required length or in coils up to 150-200 m long.
There is the possibility of simple assembly into any structure without the use of welding.

Disadvantages of composite reinforcement

There are only a few disadvantages that do not even directly relate to summer cottage construction:

At +600°C the material loses its properties, softens, and becomes less elastic;
It has a weak modulus of elasticity, much less than that of steel reinforcement, and therefore, when used for floor slabs, you should choose a different material, or carry out all the calculations correctly;
Rods cannot be welded... but this is not particularly necessary if there are other fastening methods.

As you can see, the material is excellent for country house construction and site design.

In addition, we suggest paying attention to a certain sequence of work, which will give a qualitative idea of savings and practicality:

Delivery can even take place by car, since the reinforcement coils easily fit on the trunk. They weigh a little, about 12-24 kg, depending on the diameter of the rod and the footage on the bay;
To carry it around the dacha area, you won’t need loaders or handymen; you can even carry two or three skeins at a time yourself;
A huge advantage is that the length of the rod can be up to 150-200 meters, which is very convenient compared to steel reinforcement, which is limited to 12 meters;
Installation into a foundation, frame or any other structure does not require special equipment or a specialist with special knowledge. You work as with regular reinforcement, and make the dressings with nylon clamps, without welding!

Application of material

We decided to take a closer look at the areas of application of fiberglass reinforcement in the country, and we will give some examples for this.

Bandaging the foundation for country houses

The material can be used to reinforce foundations for low-rise construction, for the construction of a summer kitchen, gazebo, shower and toilet, stove and barbecue, sauna and barn.

The reinforcement is plastic and does not require special skills for assembly. It is enough to place it in the place where the foundation is poured, bandage it and pour the concrete. Due to its characteristics, the reinforcement will qualitatively strengthen the foundation, prevent it from cracking and will not serve as “cold bridges” like steel.

Pouring reinforced areas

At the dacha, areas are often required, for example, for parking a car, for creating a canopy, and so on. We use different materials for their construction - paving slabs, masonry, simple backfilling with crushed stone, but you can always make a high-quality concrete platform reinforced with fiberglass reinforcement. What is important here is the correct calculation of the depth and dressing, then only the simplest installation and laying of high-quality concrete.

Greenhouse for a summer residence made of composite reinforcement

We built greenhouses from pipes, steel reinforcement, metal profiles, wood, metal corners and other materials, but now we have the opportunity to install a spring greenhouse in a matter of hours, with virtually no costs.

We only need to cut the rods to the required length and install them in a wooden frame or directly into the ground. Afterwards, stretch the film over the top, bring high-quality fertile soil inside and begin planting.

Since the reinforcement is light but durable and is not afraid of moisture and oxidation, such a greenhouse will have only one drawback - the film, which will have to be changed every year or two.

Reinforcement trellis

We have already looked at wood, pipes, thick wire and other materials earlier. But now you can simply cut pieces of reinforcement from a skein, install a couple of supports for vertical gardening, and make the frame out of composite material. You won’t have to spend a long time tightening bolts and nuts, welding, or hiring specialists. It will be enough to tie the frame with clamps, applying pieces of reinforcement to the main supports in the right place, and manually tightening the clamps.

In addition, strong and durable reinforcement can be used for supports in the garden and garden. You can easily make pegs for flowers and ornamental shrubs, peppers and tomatoes.

Using fiberglass reinforcement in a dacha is not just possible, but moreover, completely justified! It is cheaper than steel, easy to install, great for serious and light structures, does not require special equipment and fits perfectly into the design of the garden and lawn, as it can be selected in different shades. The material will last for many years without painting or protective agents, will help you save money and increase the practicality of working in the country.

Fiberglass reinforcement: expert opinion (video)

We do not advocate buying and using fiberglass reinforcement in the country, but simply give an objective assessment of the material. If you have interesting thoughts about the characteristics, advantages and areas of application of fittings in a summer cottage, you are welcome to discuss the article.

Reviews and comments

(No ratings yet)

Dan 01/29/2017

Composite reinforcement for greenhouse greenhouse is GOOD. But the Sun will “eat” her

Sergey 03/15/2018

We bought the fittings from the website armaturestekloplastik.rf

Vlad 04/24/2018

Building your own home requires enormous effort and expense. And it’s very nice that the cost of pouring the foundation can be reduced using fiberglass reinforcing mesh from the NANO-SK company. Since the construction site is located not far from the lake, the quality of the reinforcement, such as non-corrosion, ensuring reliable adhesion to concrete, was decisive when choosing structures for installation. Low price, strength, the ability to avoid the appearance of cracks on the surface of the foundation - the result is achieved due to the mesh maintaining its performance qualities.

Love 11/24/2018

I left the greenhouse fittings in the garden for the winter in the spring, I had to remove them with my hands, my hands were all covered in fiberglass, I put them away in the fence so I would never use them

Add a comment

Composite or, as it is also called, fiberglass reinforcement is an excellent building material for summer cottages and gardens. It consists of polymers and fiberglass, but in terms of strength and practicality it is in no way inferior to steel reinforcement. In addition, it is characterized by lower cost and ease of installation, which is why it is in high demand among summer residents and garden lovers.

How to use fiberglass reinforcement in the country?

Dacha owners often use composite reinforcement for the construction of small buildings and structures. So, most often it is:

summer kitchens,
sheds,
gazebos,
or toilet.

Also, on its basis you can build a quite decent grill or oven. The main thing is to correctly calculate the amount of material needed and secure it firmly.

Fiberglass rods are suitable not only for erecting walls, but also for laying the foundation of the above buildings. To do this, it is enough to lay them in the form of a dense mesh at the selected construction site of a particular structure, tie them tightly at the fastening points and fill them with concrete.

As we have already said, the price of fiberglass reinforcement is noticeably lower than its metal counterpart (this is clearly seen in the example of products from tpk-kompozit), so the final cost of such a building will be very affordable and economical.

Composite reinforcement in the garden

As for the garden, the fittings we describe here can be safely used for the construction of greenhouses and greenhouses. The latter can be easily constructed by cutting the rods to the required length and firmly securing them in a wooden frame (or directly in the ground).

In addition, it is great for:

garters of tomatoes, cucumbers, grapes and flowers,
garters of young trees or shrubs (which will protect their branches from breakage),
placing pegs in the desired area of the garden or vegetable garden,
as well as the design of the territory (with its help you can make beautiful barriers, architectural decorations, etc.).

Composite reinforcement is a universal material, the options for which can be used in a dacha are thousands. The main thing is not to be afraid to use it where necessary. It is quite strong and has incredible durability. Therefore, any building or structure based on it will serve for a long time and with high quality, without deteriorating at all from bad weather or exposure to other negative factors.

The question of gartering tomatoes always causes controversial judgments and debates. This mainly applies to low-growing varieties, such as Bullfinch, Gnome, Snowdrop. And yet, gardeners who have extensive experience in growing this crop unanimously recommend gartering as a way to protect the plant from breaking under ripening fruits and to grow a healthy harvest.

Characteristics of culture

In Russian, the names of this vegetable plant of the nightshade family, “tomato” and “tomato,” despite their different origins, have equal rights. South America is considered the birthplace of the culture.

Agrotechnical data:

Tomatoes require a temperature of 22-25 0C for growth and development. When the air temperature is below 10 0 C, the ovary disappears, since the pollen does not ripen and the flower is not pollinated. The tomato is a self-pollinating plant.
It does not tolerate high air humidity, but the root system requires a lot of water for fruit growth.
With a lack of light, the development of culture is delayed.
It can grow in almost any soil if properly fertilized.

Depending on the structure of the bush, the shape and nature of the leaves, and the thickness of the stem, it is divided into three varieties:

Pegs for tomato garter

standard;
non-standard;
potato

Reproduces:

seeds;
cuttings;
stepsons (side shoots).

The root system is taproot type. It forms quickly and goes to great depths. Stem up to two meters or more, erect or lodging. The leaves are divided into lobes, tender with slight fluff. The flowers are small, collected in a brush, of various shades. The fruits are juicy, of different colors and shapes.

Whether the crop should be considered a berry, which it is from a botanical point of view, is not a relevant question for practicing gardeners and gardeners. It is much more important to grow a healthy crop. One of the important conditions for this is staking the plant.

Tomato garter

Depending on the method of planting the crop, different types of garter are practiced. In summer cottages and small personal gardens, the most common method is to strengthen the stem with stakes. What to make pegs for gartering tomatoes from? Suitable for making a support:

tree;
metal;
fiberglass;
plastic.

Tree

They use tree branches, first removing the bark from them, which, if the tomatoes are watered abundantly, can produce roots. The length of the sticks depends on the expected height of the bush. If the variety is tall, then the peg should be at least 1.5 meters. An old fence picket and slats with a diameter of 20-25 mm will also work. You can use regular cuttings from shovels. To prevent the underground part from rotting, you need to burn it on fire. Thin wooden pegs will not provide a strong support for a tomato bush, because they can break under the weight of the fruit. It is recommended to sand any rough spots on a wooden peg.

Note! One end is sharpened to make it easier to drive it into the ground.

Metal

Metal garter stakes are rarely used due to the high price of this material. You can also successfully use fittings and thin pipes left over from construction work. The height of the peg depends on the tomato variety. A diameter of 5-8 mm will be quite enough.

Fiberglass

Fiberglass tomato pegs are durable and look aesthetically pleasing. It is an alloy of plastic and metal. Externally light, ribbed, similar to metal fittings. Produced by Stekloplast LLC, located in Moscow. Experienced users recommend using material with a thickness of at least 10 mm, cutting into 1.5 m sections. It does not bend under weight, does not break, and is resistant to corrosion and chemical attack. In construction it is used for concreting the foundation. The reinforcement is sold, twisted into a ring, approximately 50 m long. Cutting into pegs in a twist is dangerous, since the rod immediately straightens and can cause injury. Before cutting into pieces, the fiberglass must be carefully unrolled, preferably with two people. You can cut with a regular hacksaw with a metal blade.

Note! It is not worth stabbing, as the reinforcement may burst from the impact. After cutting, it is better to sand each peg with sandpaper. It should be stuck or screwed into the ground.

Plastic

Garter material for plastic tomatoes can be purchased at gardening, construction and other specialized stores. It is, of course, not as durable as metal and wood, but it looks neat and aesthetically pleasing. Often there is a light metal rod inside the plastic, which gives the peg greater hardness. Plastic pipes cut to the required height are also suitable.

Pegs for gartering tomatoes - use and benefits

Early ripening and low varieties of tomatoes can do without tying. Whereas tall plants require support for healthy growth. Before making a decision, you should consider a number of advantages of garter in crop care:

Fracture of the stem under unfavorable weather conditions and under the weight of the fruit is prevented.
When watering, moisture does not fall on the leaves of the plants. This fact is important for the healthy development of the tomato bush.
The bush is open, which provides it with enough light, sun, and air. The spraying procedure becomes simpler and more efficient.
The stepsons are clearly visible and easier to remove.
The fruits do not touch the ground, which ensures their uniform and healthy ripening.

In order not to damage the root system of the tomato, the peg for tying should be placed at a distance of 10-15 cm from the plant stem and deepened 25-30 cm into the ground. One support per bush is enough. Tomato stakes made of fiberglass reinforcement cannot be driven in. Fiberglass may delaminate.

Fiberglass may delaminate

Then, not tightly, taking into account the possible thickening of the stem, the bush is fixed with twine, wide tape or any soft material cut into large strips. The trunk of the plant is wrapped with the selected garter material, the ends are folded in a figure eight, twisted and tied to a support. Special plastic clips and loops for fastening can be purchased at gardening and hardware stores. It is not recommended to use fishing line, thin threads, or wire. Such fixation can damage the plant trunk.

Note! When reusing garter material, it must be disinfected with a manganese solution or boiling water. The use of chlorine is not recommended. Tomatoes are very sensitive to it.

Gartering on pegs is not the only option for attaching tomato bushes to supports. Depending on the crop variety and planting location, fixation is used:

for horizontal and vertical trellises;
on mesh and wire fences;
on frames made of various materials and various shapes;
on loops and hooks according to the Maslov method (more suitable for greenhouses and closed ground);
on twine with twisting (advisable in greenhouses).

Tomatoes grow in almost every garden plot. A lot of different information has been written about caring for this crop on the Internet and in periodicals. Beginning gardeners have a unique opportunity to apply this knowledge in caring for tomato bushes in their plots. And experienced gardeners and summer residents can broaden their horizons. Everyone will learn something useful and new for themselves.