Kitchen corner effect assembly diagram. DIY kitchen corner: a detailed guide

A successful design solution in the form of a kitchen corner will never go out of style. This is a comfortable, functional furniture product that does not take up much space, but at the same time allows three or four people to sit comfortably at the dining table. There are many different models on the market today. But, experienced home craftsmen, who are accustomed to doing everything in the house on their own, recommend building a kitchen corner with their own hands according to drawings and diagrams. If you act step by step, with maximum effort and ingenuity, you can make a beautiful and solid corner.

We take into account the details

Before starting work, it is important to decide where the future product will be located. Having chosen the desired side and dimensions, we display the structure in the drawing. The figure should show the height of the seat, backrest and the width of the entire product. Measurements should be as accurate as possible, as this will help in the future to acquire the right amount of material.

The next important step is the choice of upholstery and filler. The best choice for a kitchen product would be microfiber, synthetic material, leatherette. Experienced craftsmen advise purchasing microfiber for sheathing the structure. Microfiber does not accumulate dust, moisture, it is easy to clean and keep clean. To fill the soft corner, you can purchase foam rubber, but it is better if there are polyurethane foam plates. Design preparation

A do-it-yourself kitchen corner in the photo always consists of a short and long sofa, as well as a connecting part. How many sheets of chipboard and filler panels are required is calculated according to the drawing. In order not to make a mistake in choosing a height, you can take a stool as a sample. Having prepared the materials, you should choose the right tools. Step-by-step instructions from experienced craftsmen advise using the following devices in your work:

First of all, it is necessary to cut structural details from chipboard sheets. At the end of this stage of work, the following should be ready:

2 side parts.
Bottom and side frame elements.
Back and seat.
Plank for top and seat.
Thrust element for slats.

Having prepared the structural elements, it is necessary to mark the points for milling and installing screws. Then we trim the ends with an edge, and the lower part with thrust bearings.

The next step is the installation of the box, which should consist of two side sheets and one bottom sheet. The bottom can be made of plywood. To connect all the elements of the box, it is recommended to use self-tapping screws.

Then a back is constructed, which is attached to the sidewalls with the help of dowels. To strengthen the structure, metal corners are fixed.

Construction of the short section

This part of the kitchen corner may have the following dimensions:

In order for the kitchen corner in the photo to be as close to the wall as possible, sharp corners must be cut on the back. Unforgettable, connect the thrust bar to the seat. As soon as the back and seat are connected using metal corners and dowels, the sidewalls can be attached.

Final stage

The wooden base of the corner must be upholstered with a cloth and filled with filler. The first step is to cut the polyurethane to the size and shape of the back and seat. Two pieces of upholstery material are cut out in the same way. To prevent the filler from moving, it should be fixed with glue. And the fabric - with a stapler. We pay special attention to corner fastenings. Before fixing the material, it must be collected inside and closed with additional pieces.

If restoration is required over time, it will be easy to drag the kitchen corner with your own hands. The master, knowing how the material was fixed, can easily cope with the task of updating outdated furniture.

At the end

If the home master decided to build a kitchen corner with his own hands, the step-by-step instructions are presented in the video in detail. To make the design beautiful and durable, it is important to choose high-quality chipboard sheets, upholstery fabric and filler. Be sure to make a drawing before starting work, which will take into account the dimensions of the structure. Further, following the steps, the master will be able to build a high-quality and beautiful kitchen corner that will delight for many years.

Any adult man can make a soft corner for the kitchen, if he has free time for this, the necessary tool and desire.

A soft corner for the kitchen is like a final chord, like a beautiful photo frame. It completes the interior, gives it a cozy and homely look. And it's also so nice to gather the whole family for breakfast or dinner. A neat and ergonomic set does not take up too much space, while 5-6 people can easily sit down here. So if your kitchen cannot boast of a large area, a corner will be a great option.

A suitable set of furniture can be purchased at any store - the cost of such corners is usually low. But in the photo in the catalogs and in life they look somehow very ordinary. And if you have a desire to make something really exclusive, you can assemble such a kit with your own hands. And our instructions and photos will help you with this.

Deciding on sizes

First, we need to come up with our soft kitchen corner: determine the dimensions, design features, build drawings and cutting patterns. We will work with inexpensive chipboard boards - they are easy to cut even with a hand tool, and it’s easy to buy at any hardware store. Alternatively, the cut can be ordered to the nearest workshop in your city, having previously prepared a specification for furniture cases.

When choosing the design of a kitchen sofa, it is better to stop at a modular assembly, since the corner section without additional racks will not be reliable enough. The corners of the pallets also look interesting and are quite reliable.

The dimensions of upholstered furniture are best determined on a kitchen plan drawn to scale (you can use graph paper). Here the main thing is to “place” the corner so that the passage between the dining group and other furnishings is at least 60 cm. The rest of the parameters are also chosen arbitrarily, but use the following numbers for guidance:

The height along the back can be any, especially if it is curly, as in the photo of designer furniture. But the most comfortable is the kitchen corner "height" 85-95 cm.
The optimal seat depth is 45-50 cm, just keep in mind that there will still be a thick layer of foam rubber on the back, which will steal a few centimeters. So chipboard blanks will be a little wider.
You choose the general dimensions of the furniture in length and width, but if the area allows, it will be enough to make a standard corner of 1.2x2 m.

If you liked the photo of the dinette, and its dimensions do not fit your kitchen, you can adapt the peeped version. Just calculate the multiplicity for one of the parameters to get a constant factor and translate all the values from the original drawing into your dimensions.

Materials and cutting

To make a corner with your own hands, you will need laminated chipboard sheets with a thickness of 16-18 mm. When the furniture drawing is ready, you can complete the detailing by laying out the corner on the planks. Carefully examine the photo of the model you like and, if possible, from all sides, so as not to miss anything.

You should end up with a spec like this:

The front panel of the box under the seat - 2 pcs. and the same number of back walls.
Curly racks (support sidewalls) - 4 pcs. or 6 if the sofa will consist of three separate sections.
The bottom of the box (you can use fiberboard) - 2 pcs.
Seats and backs - 3 pcs.

All this needs to be “decomposed” with paper or in a special computer program on a standard chipboard sheet in order to build a cutting pattern. Examples of detailing specifically for kitchen corners can be found in the photo on the Web. Then it only remains to give the drawing to the furniture makers or use it yourself if it is decided to do all the work with your own hands from and to.

After cutting, the finished parts must be fed. To do this, it is better to take a good tape made of ABS plastic with an adhesive layer already applied, instead of cheap and short-lived PVC. However, this service can be ordered by specialists who will cut furniture sheets for you.

The most difficult moment in the whole work is the back of the corner section of the kitchen sofa. It will not be possible to make it semicircular from a chipboard sheet with your own hands, so it is better to immediately simplify the task and assemble it from three separate panels.

To cover the sofa with your own hands, you will need to purchase foam rubber 38 g / m 3 5-10 cm thick, dense upholstery fabric such as tapestry, jacquard or artificial leather, as well as a thin non-woven fabric to close the fasteners on the back of the kitchen furniture. Blanks for soft elements are lubricated with glue and a packing is placed on it. At the same time, foam rubber sheets for seats are cut 2 cm wider in order to bend the edge inward at the end. For the backs, 4 cm are added, since here you will have to bend the foam rubber both from above and from below.

Having cut out with your own hands a fabric for covering furniture with a margin of 5-10 cm for folds on each side, it is attached to the seats with a stapler. In this case, the material must be well stretched, and the staples must be driven in around the entire perimeter as often as possible. We do the same with the backs. Particular attention should be paid to the corners: the more carefully you fold and secure them, the more your homemade sofa will look like a photo from a store catalog.

All elements of the kitchen corner are ready, it remains only to fill the thrust bearings on the ends of the side legs. You can do without them, but in the case of chipboard, it is better to spend a few more minutes to get everything right. Firstly, small supports will allow you to safely move furniture along the floor without scratching the coating and without flattening the lower edges. Secondly, they will slightly raise the corner, so that during mopping you will not damage or wet the chipboard. Yes, and the kitchen sofa on neat thrust bearings looks more aesthetically pleasing - you can’t distinguish it from the factory one from the photo.

Assembly

Now you have a designer in front of you, which remains only to assemble with your own hands into a single set. The sofa and side seat boxes are mounted in the same way:

Mark the sidewalls and drill holes in them for the dowels. Place support bars on them, which will take on the weight of the bottom of the box and the top of the seats.
Screw metal corners 27x27 to the sides of the case - 4 for each. Through them, attach the back walls of the furniture to make an open box.
Install the bottom of the polished chipboard on the resulting frame, and then screw the front panel to the screeds. Moreover, it is better to tilt it a little - by 10 degrees, so that those sitting at the table are comfortable, and the bar does not interfere with the legs.
Screw the support bar from the inside to the back wall of the box, and put the piano hinges on it and fix the folding seat on them.
Screw the backrests with euro screws to the sidewalls, making a slight slope of about 5 °. They are attached to the benches through a support bar, planted on dowels, and with the help of slightly unbent metal corners.

Now our kitchen sofa is more like a pair of separate benches that will be connected with a corner module. It is easier to make it without the bottom box, but with its own side supports for strength. In fact, here you just need to screw the strips under the seat to the figured legs and fix the segment already covered with fabric on them. With the help of dowels, a back is attached to it, which in this case plays the role of an additional stiffener. That's all - the assembled module can be screwed to the short and long benches of the corner, pulling them together, and your

The design of the dining area should be not only practical, functional, but also as comfortable as possible. It is here that the whole family gathers together, eats, communicates. Many people prefer to make a kitchen corner with their own hands, then it fully corresponds to the parameters of the room. Products are versatile, convenient, do not take up much space. Standard designs consist of a pair of small sofas and a connecting element between them.

Before you figure out how to make a kitchen corner with your own hands, you need to clarify the main nuances of assembling furniture:

The accuracy of the work directly affects the functionality of the products, and the final result depends on many factors.
At the stage of designing a kitchen corner, individual tastes and preferences of people are taken into account.
If ready-made schemes are used for manufacturing, then you will have to work with the indicated materials. Otherwise, backlashes and gaps will appear in the design. It will require strict adherence to the assembly order, as well as the selection of high-quality fittings.
If there is no experience in creating furniture, you should give preference to the simplest straight-line models of kitchen corners with laconic decor.
When selecting suitable drawings for a kitchen corner, you must be guided by the available tools. So, the manufacture of a wooden model is not complete without a grinder, a jigsaw.

To carry out a high-quality assembly, you should think over the appearance of the kitchen corner in advance, determine the place where it will be located. This information will help you choose the most suitable materials and accessories.

The secret of the popularity of the kitchen corner lies in its aesthetic self-sufficiency. Corner sofa with a table form a separate comfortable area.

Material selection

A self-made kitchen corner should be practical, convenient and attractive. In many ways, these properties depend on the selected material. In the old days, furniture was made exclusively from wood, today there are other options.

frame

First of all, a kitchen corner frame is made - a supporting structure on which all other elements are fixed. The configuration, strength, capacity of the product depends on it. To create kitchen corners with your own hands, natural wood and chipboard are suitable. You should first evaluate the features of each material, the nuances of working with them:

Chipboard is the cheapest and most affordable option. The advantages are that it has environmental safety, reliability. Difficulties in working with particle boards arise at the cutting stage. In production, the procedure is carried out using special machines. At home, work is often done with a jigsaw, which can lead to the formation of uneven edges and chips. Moisture gets into the damage, as a result, the sheets swell and deform. To prevent trouble, you will need special edges that are fixed on the cuts.
The wooden corner is characterized by durability, strength, resistance to wear, environmental friendliness - these are pluses. When working with the material, it is necessary to follow the drawings exactly; before assembly, treat the panels with special compounds that prevent decay.

For independent production of furniture, such species as linden, Christmas tree, birch, pine are best suited. They are the softest, easier to process and assemble. If conifers are used, it is important to take into account one more nuance - they must be thoroughly dried so that the resin does not stand out.

Natural wood is one of the most expensive materials, so it is better for beginners to train on simpler and cheaper raw materials. Chipboard will do.

Chipboard

natural wood

Upholstery

A soft corner for the kitchen is not only functional, but also a decorative element of the situation. To create upholstery, you can use various fabrics, the color and design of which should be combined with the interior:

Tapestry. Dense textile, resistant to wear and mechanical damage. Differs in a wide variety of colors, serves for a long time, looks presentable.
Velours. Pretty durable material with a short pile. It looks beautiful, but over time it can rub off and lose its attractiveness, it requires special care.
Flock. Often used in the manufacture of kitchen corners with their own hands. Reliable beautiful fabric endures mechanical stress, has a waterproof impregnation, thanks to which dirt is easily cleaned.
Jacquard. Luxurious material, pleasant to the touch, but has significant drawbacks. It wears out quickly and loses its original appearance, stains are difficult to remove from the surface.

The most popular type of upholstery for kitchen models is high-quality leatherette. In terms of structure, properties and appearance, this material practically does not differ from natural, but the cost is several times lower. It also has some disadvantages: lack of breathability, susceptibility to mechanical stress. For covering furniture, it is better to choose thick canvases, thin ones can quickly become cracked and torn.

Tapestry

Velours

Flock

Jacquard

Leatherette

Measurements and drawing up a drawing

First of all, the length of the walls of the kitchen is measured, as well as the corners of the room. The dimensions of all sofas are determined. The default settings look like this:

Seat height - 40-50 cm.
Depth - about 50-70 cm, so that it is comfortable to sit at the table, and the legs do not rest on it.
The height of the entire structure, together with the backrest, can reach 95 cm, but this is not the limit.

The easiest way is to use ready-made drawings and diagrams, especially for people who are faced with making furniture for the first time. You just need to choose a plan that matches the desired size. If you adapt the model you like to individual parameters, it is easy to make a mistake, and you will have to spend a lot of time on alteration. The scheme should reflect all the design features: the presence of a bed, drawers and the nuances of their opening, the structure and location of the folding mechanism. It is important to be able to clearly assess the correctness of the drawings, not to take the first example found on the net.

Take measurements of the length of the walls and corners of the kitchen

Standard parameters of the kitchen corner

Corner manufacturing algorithm

Traditional kitchen corners with dimensions of 110 x 160 cm are optimal for accommodating three people. Products are convenient for a full-fledged meal by people without crowding and touching each other with elbows. Creating furniture according to individual parameters has the advantage of matching the dimensions of the room. Upholstery is selected based on your own taste preferences and the overall style of the interior. The product can be supplemented with the functionality that is needed: a folding sofa for sleeping, storage space, or both.

Chipboard with drawers

To make a do-it-yourself kitchen corner from chipboard, complemented by drawers, you need to follow several steps:

preparation;
measurements of parameters;
drawing up a detailed drawing;
purchase of accessories and fasteners, upholstery;
sawing wood chip sheets in a furniture shop.

Design begins with the choice of the optimal place where the sofa will be located. It is on the basis of its area that the appropriate configuration and dimensions of the future product are selected. It is necessary to act according to the instructions:

All elements are cut according to the template, polished.
The edges are taped.
Assembly is carried out with the help of dowels and confirmations. First, the short and long parts of the sofa are connected, then the seat with the back, which are attached to the sidewall, then the boxes are made.
The connections responsible for the rigidity of the product are fixed with metal screws.
The final step will be the upholstery of the furniture. The filler is cut from polyurethane plates. The size is needed larger than the elements for which it is intended. The filler is attached to the seat and back with glue.

To make the corner correctly, it is necessary to take into account the size of the kitchen, the placement of household appliances and furniture. At the narrowest point, the width of the passage must be at least 60 cm. The parameters indicated in the diagram may vary depending on the optimal dimensions of the model.

The default values remain unchanged:

seat height - 45 cm;
depth - 50 cm;
the length of the large and small sofas is 120 and 200 cm.

The height along the upper edge of the backrest should not exceed 95 cm. The do-it-yourself kitchen corner is made from polished laminated chipboard with a thickness of 16 mm. To process the cuts, you will need an ABS edge.

Cut out all elements. sand, glue the edges with tape

Collect the first part with the help of dowels and confirmations

Craft boxes

Attach second part

Glue the filler on the walls of the seats, attach the seats

Fix the backs

simple wood

To make a simple set of wood, you must first draw a plan, carefully measure all the parameters. You can purchase ready-made furniture panels according to the dimensions obtained. In total, 3 types of elements are required: 6 identical sidewalls, 3 upper and lower boards. The model is created according to the instructions:

All parts are cut across.
The bottom board is located between the side boards, the top board rests on them, like a lid. This feature should be taken into account when calculating the width of the material.
The surface of the elements is carefully polished.
Holes are drilled into which dowels are inserted.
The kitchen corner made of wood is painted in a color that will be in harmony with the decor.

When making furniture, we must not forget about the importance of the location of the dowels. It is necessary that they coincide with the holes in the mating parts.

The product is painted twice to increase resistance to wear. After drying, the boxes are installed in the right place, optionally fastened to each other. A soft seat is placed on top, which you can purchase or sew yourself.

Corner scheme

cut details

Assemble sofa frame

Lacquer

Install bottom boards

Cut the foam to the size of the top board

Glue filler

Upholstered seats with fabric

Install drawers, attach seats

With sleeper

Before assembling a kitchen corner, it is necessary to take measurements. The parameters of the proposed product are 1.5 x 2 m. For work you will need:

timber 30 x 5 cm, as well as 50 x 50 cm;
foam rubber 60 mm;
plywood 15 and 4 mm.

Actions are carried out according to the scheme:

The material is carefully polished, cut into elements according to the sample.
You can assemble using self-tapping screws or a spike.
To create a bed, you will need to purchase and install a retractable mechanism.
Armrests, frame are produced.
The upholstery is created from materials that you like more: leatherette, furniture suede, textiles. It will take at least 7 running meters.

The kitchen corner with a berth should be soft enough. For this, fillers in the form of synthetic winterizer or foam rubber are used. When unfolded, a full-fledged resting surface is obtained with a size of 1.9 x 0.9 m. The parameters, together with the armrests, are 155 x 210 cm.

The process of creating and assembling kitchen corners is a difficult but exciting job. Beginning craftsmen should use ready-made drawings, experienced ones will be able to make them themselves or change the parameters at their own discretion. Self-manufacturing allows you to create unique products that fit perfectly into the space, in harmony with the interior.

Sand the material, cut into elements according to the pattern

Assemble the frame

Video

If you have long overdue the question of replacing kitchen furniture for the dining area, then you can easily solve it without spending a lot of money on a store set. Any home craftsman can make a kitchen sofa with his own hands. So you can not only save money, but also contribute to the design of your personal space.

You will not have any difficulties with finding drawings of a corner sofa in the kitchen. You can find a suitable drawing with suitable dimensions on the Internet.

Make a kitchen do-it-yourself corner can be made from available materials and with the help of tools available in each household. If, in addition to everything, you follow the recommendations for making a corner for the kitchen with your own hands, then after completion of the work you will not have to deal with the elimination of the miscalculations you made.

How to design a kitchen corner?

The process of assembling a kitchen corner with your own hands can be represented as a series of successive stages:

Drafting

Directly before assembly do-it-yourself soft corner, you should already have a correctly drawn up drawing. The first question that you must decide is to choose a place in the kitchen for your corner sofa. Given its size, you have to select the dimensions and configuration of the corner in the kitchen:

Length and depth of sections;
The option of placing the short part of the sofa is relatively long;
Height taking into account the upper edge of the back;
Way of fastening of sections - monolithic or modular.
Upholstery and material for the manufacture of the frame.

When choosing corner sofa drawings for a kitchen with our own hands, we advise you to consider only those models that have a separate corner module in their design. Side sofas, which have one corner seat attached to furniture corners, will not last long due to the low reliability of such a connection. An attempt to save on material by refusing to use two racks in the design will not live up to expectations, as a result, the corner will turn out to be extremely fragile. Therefore, for the kitchen it is best to choose modular designs, which, if necessary, can be quickly transferred to free space.

Another advantage of sofas of this design is the ability to change the configuration from right-handed to left-handed. As places for installation modular kitchen corners, you can choose the corner of the room or the option when the furniture is placed in one line. When calculating the length and width of the corner, it is imperative to take into account the area of \u200b\u200bthe kitchen room, as well as the location of other interior items and household appliances. After the kitchen sofa appears on your plan, you need to pay attention to the passage, the width of which should not be less than 60 cm at the narrowest point.

In order to accurately and without errors calculate the size of a corner sofa and determine a suitable place for it, you can choose a suitable drawing of a kitchen sofa on the Internet. Naturally, the dimensions given in it will not correspond to your room, so they will have to be recalculated taking into account the dimensions of your future corner.

But remember that all kitchen corners have dimensions that remain the same regardless of the version of its execution:

Height along the upper edge of the back - 85-95 cm;
The length of the short and long sofas is 120 and 200 cm;
Seat depth - 50 cm;
Seat height - 45 cm.

Materials for the kitchen corner

As a material for the manufacture of a kitchen corner, you should take laminated or sanded chipboard 16 mm thick. Do not forget about finishing the end part of the blanks, on which you need to install the ABS edge. If we consider in more detail the design of the sofa frame, then it should include the following elements:

Two straps - supports for the back.
Top bar of the drawer.
Two side racks.
Back wall of the box.
Front panel of the lower drawer.
Drawer bottom, seat and back.

To make the bottom and back wall of the box, as well as the seat, experts advise taking a rough chipboard.

Often in stores you can find a PVC profile, but you should not use it to make corner parts. This is a very unreliable option for the edge, which, with the active use of the sofa, will quickly move away.

If you want your homemade kitchen couch to look the same as factory products, then it is advisable use chipboard cutting services. To do this, you need to contact any furniture workshop, where you will definitely find machines for cutting sheet chipboard. They are engaged in sawing both for their own needs and for individual orders. But before contacting the workshop, you need to draw up a detailed drawing of a corner sofa for the kitchen at home and indicate the dimensions of each element.

After that, you transfer the drawing to the technologist, and he already puts all the dimensions into the program, which draws up a cutting chart and determines the number of chipboard sheets required. At the same time, the total number of running meters of cut corresponding to the trimming tape is calculated. But not all the work can be done by a furniture workshop. Curly details you will have to do at home. But they must still be present in the submitted list and be indicated in the form of rectangular blanks.

You can additionally pay specialists workshop for cutting out figured parts from chipboard and gluing miter tape on all blanks. This option is often chosen by home craftsmen who want to minimize the amount of work at home. Please note that the fastening of the ABS tape with the help of a machine is performed better than manually. As a result, the master saves himself from having to deal with milling parts and creating templates for them at home.

Some owners want save as much as possible in the manufacture of a kitchen corner from chipboard, and therefore they plan to mill curly parts on their own. In this case, they need to adhere to the following recommendations during this work:

When choosing ABS tape for edging keep in mind that it may already include glue or be without it. The blank belt is intended for milling on machine tools. In this case, the glue is supplied from a separate container. If, due to inattention, you acquire this particular type of tape, then you will not be able to make a corner with it at home.

Having finished milling operation elements and fixing the tape on the ends, you can start marking and assembling sofas. When you mark the holes on the surface of the side posts, keep in mind that the front of the drawer should go 2 mm into the depth of the material. As a result, the center of the hole will be offset by 10 mm from the edge. At the lower ends, it is necessary to fix the thrust bearings.

As a fastener for kitchenette chipboard use confirmations and dowels. For joints that provide structural rigidity, it is best to take metal screws. In other cases, it is recommended to use dowels. This solution can minimize the number of through holes. Dowels are the only fastener that is used to connect the lower backrest support bar to the main structure.

Upholstery and assembly

quality corner, handmade, should not only be reliable, but also look beautiful. So you can not do without a stylish upholstery. When choosing a material for wrapping a corner, you should pay attention not only to its practicality, but also to the correspondence of the appearance to the design of the room.

at first foam rubber must be glued on the parts with a density of kg / m 3. The soft elements of the corner for the kitchen are considered to be the back and seat. In the process of preparing the back for upholstery, it is necessary to cut a rectangular piece of foam rubber 4 cm wide more than the width of the back. A supply of material will be needed to bend the foam at the end of the part.

The foam rubber blank for the seat is made 2 cm wider than the structural element itself, since it will only have to be wrapped at the ends from the front. Foam rubber is attached to the tree with glue fast installation.

Then he proceeds to cutting the fabric: on a prepared piece of upholstery lay the main element and outline it. Then, 5 cm are added on each side of the drawn line and a pattern is made along the new border. The result should be a fabric with dimensions exceeding the width and length of the fitted part by 10 cm.

For fastening fabric with a collar use a stapler, fixing the upholstery material with it only on one side of the part. Then the fabric must be evenly stretched, and only after that it is attached to the part from the back. Similarly, the remaining sides are fastened with a stapler with a stretch.

Conclusion

To the hostess as well other family members felt as comfortable as possible in the kitchen, it is necessary not only to purchase functional household appliances for it, but also to resolve the issue with the kitchenette. But this does not mean that you need to go to the store for furniture for the dining area. You can do it yourself, especially since this task is not as difficult as it might seem at first glance.

To get started you will need make a detailed project, reflecting in it the exact dimensions of the future corner in the kitchen. To make the corner look as stylish as the factory product, it is best not to make blanks on your own, but to use the services of a furniture workshop.

One of the popular design solutions used in the design is the installation of a corner. Such a piece of furniture has earned popularity due to its functionality, attractive appearance and the ability to optimize the use of space. This is especially important for small spaces. However, even in spacious kitchens, a corner will not be superfluous - it will perfectly perform zoning of space.

Do-it-yourself kitchen corner - drawings and diagrams

What are kitchen corners

A piece of furniture, as the name implies, is installed. The ensemble may include all elements: sofas (straight and corner), a table and chairs (stools). But most often the corner is purchased separately in the form of three modules: long sofa, smaller seat and corner pouffe. Table and chairs (if necessary) are purchased separately by the owners.

As a rule, the configuration of the assembled corner resembles the letter G, however, U-shaped models are also available. The design can be solid or modular. In the first case, it is necessary to specify the orientation of the furniture (right or left). Models are available that allow the use of a longer module as a linear element, while the second element can be installed at a distance. Models with puffs symmetrically located relative to the corner element fit perfectly into small kitchens, each of which can accommodate one person. The corner can be installed even in a bay window, only its shape will be semicircular, triangular or polygonal.

For housing in which there are not enough beds, and situations when it becomes necessary to accommodate a guest with an overnight stay are not uncommon, a module with a full-fledged folding place to sleep will be a real salvation. A mini-bar can be placed at the end of the sofa or a reclining shelf can be installed, which can be used as a.

What to look for when choosing a corner model

When purchasing finished products and when making furniture with your own hands, a number of factors must be taken into account.

Room dimensions

Kitchen interior items may vary in size and number of seats. It is necessary to select the configuration of the corner, taking into account the layout of the kitchen, its size and the rest of the situation. The installed corner should not serve as an obstacle to a comfortable stay in this room. A convenient option for kitchens with a shortage of free space is a corner with a transforming table. As additional seats, if necessary, you can use folding stools.

Kitchen options:

corner modules to accommodate four people;

model for a company of six people;

compact model for three diners;

sleeper module.

Number of family members

The furniture installed in the kitchen should allow everyone living in the house to comfortably sit at the dining table. It is also necessary to take into account the possibility of the arrival of guests. Of course, if the dining room is not intended for such gatherings. It should be borne in mind that a person of average build needs at least 60 cm for comfortable seating at the table.

Ease of use

The corner can be rigid or have a soft filler under the upholstery. In the first case, sitting on the sofa will not be very comfortable, especially for a long time, but it will last much longer. In addition to the fact that the upholstery of soft models wears out faster, the filler itself has a service life (for polyurethane foam - 10 years, for foam rubber (its elastic modification) - 3 years). In addition, rigid models are less prone to contamination. Such systems, as a rule, are cheaper than more comfortable counterparts. And you can solve the issue of excessive rigidity with the help of pillows.

Availability of storage places

The produced models allow not only to use the furniture for its intended purpose, but also to optimize the occupied space as much as possible. The presence of niches under the rising seats, in which you can store household belongings and products, or drawers helps a lot, especially for owners of small spaces.

The material from which the body is made

Connoisseurs of natural materials and comfort in the interior will suit corners made from solid wood. They are attractive and environmentally friendly, but, as a rule, quite expensive. The analogue of the tree is chipboard and LMDF. These, cheaper and not always safe for health materials, are currently most often used in the manufacture of furniture. If desired, you can also purchase a corner made of metal. Metal structures are characterized by durability, strength and resistance to external influences, but they can not be installed in all interiors. Often a combination of different materials is used in production.

Upholstery material

You should choose the appropriate option, focusing on the design of the room and the functionality of the coating. For finishing, natural or artificial leather can be used. Recently, the synthetic version is practically not inferior in quality to the original, but its cost is significantly lower. The impregnated synthetic fabric is also quite easy to clean from dirt, does not fade in the sun and does not attract dust. Aesthetically looking and pleasant to the touch fabrics with pile are not so easy to care for. A beautiful jacquard that looks like a tapestry, or suede can be expensive. A good option is a Teflon coating on a fabric basis. Models with a combination of finishing material are interesting.

Kitchen design style

This factor is closely related to the previous two. If the kitchen is decorated in high-tech or techno styles, you can opt for metal structures. For classic kitchens, wooden furniture is suitable. One thing is important - the installed corner should not stand out from the general concept of decoration and furnishings.

Prices for different types of kitchenettes

Kitchen corners

Do-it-yourself kitchen nook production

Assembling a corner for the kitchen on your own is not an easy task, but quite feasible. When making furniture, the following steps must be followed.

Take measurements of the kitchen to determine the dimensions of the structure and the placement of furniture. It is necessary to consider the location of the door and window.
Make a drawing of the assembled structure. You can make it yourself or use ready-made options.
Purchase materials and accessories. Carry out cutting according to the drawing.
Assemble the corner from the prepared parts.

It is easiest to make a corner on your own, the body of which is made of wood or wood-containing materials. Those who do not have very good carpentry skills or do not have the right tools can use the services of specialized organizations and order cutting parts according to their drawings there. Those who want to make furniture on their own, at a minimum, must have a circular saw, a milling machine, a screwdriver, a grinder and a stapler, if they have to upholster products with material.

Prices for staplers

Construction stapler

Average dimensions for a kitchen corner where it will be convenient to sit at a meal:

height from the floor surface to the seat: 45 ... 47 cm;
height including backrest: 87 ... 90 cm;
seat depth: 45…50 cm;
the total length is calculated individually, based on the needs and dimensions of the room.

Take for example a standard design with three seats for a long sofa and one for a short one.

The height of the corner is 90 cm, the height of the seat is 45 cm, its depth is 50 cm. fillers.

Corner assembly technology (for example, a long sofa)

Step 1. The first stage in the production of a sofa is the manufacture of a box.

On the dowels (glued) the sidewalls, the bottom, the front wall of the frame are assembled. It turned out to be a fairly simple design.

The back sides are attached.

Prices for cordless drill/driver

Cordless Drill

Support rails are installed.

Self-tapping screws are used for connection. Attached slanted backrests.

Self-tapping screws fix the back of the chipboard.

Horizontal slats are installed in the box, hinges are mounted to them (for now they are only being baited, they will be finally installed after the upholstery of the sofa), with the help of which the cover of the box will rise, which serves as a seat.

The rising cover of the box is cut to size (also from chipboard).

Step 2 Upholstery is being prepared. Pieces of foam are cut off.

Installation of soft filler is carried out on a special glue, which is designed for gluing wood and foam rubber. Foam rubber is attached to all surfaces of the corner frame, except for the bottom. Thicker material is used for the upholstery of the back and seat.

A synthetic winterizer is laid on top of the foam rubber (it reduces friction between the upholstery and the filler).

The skin substitute is cut out, the cover is sewn together.

Important! Correctly measuring for the manufacture of a cover and sewing it is not at all easy. It is recommended to contact the relevant organization for this.

The material is securely fastened to the corner. You can't do without a furniture stapler.

Foam rubber with padding polyester is also laid on the seat and covered with material.

Prices for the model range of pneumatic staplers

Pneumatic staplers

Step 3 The frame on the back side is sewn up with a thin sheet of chipboard.

Sheathing material is attached to it, after which the back wall is also decorated with a leather substitute.

Loops are attached. A seat is hung on them.

In the same way, a small sofa is assembled and ennobled.

Furniture upholstery must be treated responsibly, as any defects in the form of folds or protruding material will instantly spoil the appearance of the furniture. On the second structure, seat loops are also installed.

The skin substitute is firmly fixed around the entire perimeter. Legs are fixed.

The result is a very attractive and stylish design, which, moreover, is functional, because, thanks to the rising seats, it was possible to organize additional storage spaces for various kitchen utensils.

It is not so easy to assemble such a structure on your own. The most accessible scheme for assembling a kitchen sofa is as follows.

When cutting foam rubber, it is extremely important to take into account the allowance for closing the ends. Soft filler and fabric are fixed with a stapler. Structurally simple, but elegantly decorated corner, produced on their own, will be able to adequately fit into the interior of any kitchen.

Upholstery of kitchen furniture largely determines the appearance of the structure. However, it should be remembered that the defects that have appeared in the coating are not a reason to send the model that has served faithfully for scrap. Armed with a stapler and glue, having prepared a new fabric and foam rubber, you can quite quickly not only restore the appearance of an interior item by removing the material that has become unusable, but also make the furniture even more attractive.