Helpful mechanical device A vice used by craftsmen to fasten parts during processing is a vice. They are effective in cases where it is necessary to install the workpiece on safe removal or it requires rigid and reliable fastening. What types of devices exist and how to choose them will be discussed in this article.
Design Features
Enlarged, this device consists of two jaws, one of which is fixedly attached to the body or frame, and the second is movable, capable of moving. A locking mechanism is used to clamp the workpiece in the jaws. It consists of several elements, as can be seen in the photo of the vice:
Steel threaded lead screw trapezoidal shape. The movement of the screw is controlled using a handle.
Cast iron plate for support or frame. It is possible to use steel or duralumin construction.
Sponges have screw fastening. If you rotate the screw clockwise, the movable jaw begins to move towards the frame, thereby securing the part. When the screw rotates in the opposite direction, the jaw moves away from the bed, freeing the workpiece.
Several methods are used to attach a vice to a support:
- stationary with regular use in one place;
- on a clamp, which provides less reliable fastening, but the ability to use without a permanent workbench;
- on suction cups – used when attaching exclusively to a flat and smooth surface.
Types of instruments
Vise machines are generally classified according to the technology used to activate the screw. They can be manual or pneumatic. Based on the design features, rotary and non-rotary vices are used.
Some manual models allow you to manipulate long parts. For these purposes, a wide anvil and the possibility of vertical fastening of the workpiece are provided. There are also models for clamping round parts.
Locksmith type tool
Special bolts are used for mounting on a workbench or table. The design of the device is all-metal.
It is possible to choose a stationary or rotary model for the purpose of processing parts with the ability to change angles. The width of the jaws varies between 45-200 mm with the possibility of a jaw stroke of 140 mm.
Advantage of this type is the wear resistance of the jaws, the strength of the anvils, small size and weight, the ability to rotate 360 degrees in rotary models. However, at the same time:
- require constant alignment of the position of the jaws;
- equipped with quick-wearing lock washers;
- clamping long workpieces is difficult;
- have backlash available.
Bench vices can be parallel or table. With parallel jaws, the displacement of the jaw is ensured by rotating the screw parallel to the stationary part. They can be rotating or non-rotating.
But the dining room model is an outdated option. Although this is a very simple vise design, it can hold long parts.
Machine design
This is a more accurate version of the device for securing parts. It either has no play at all, or the amount of run-up is minimal. The vice is mounted on a workbench and is distinguished by the presence of a rotating mechanism.
You can choose from the following options:
- stationary with fastening perpendicular to the position of the tool;
- sinus with installation of the part at an angle;
- multi-axis with the ability to rotate along several axial points.
The machine vice guarantees a strong clamp, which is especially important when processing metal parts. They are equipped with a durable body and a protective anti-corrosion coating. Rigid fixation ensures high precision work.
However, if the workpiece is clamped in a bent way, marks may remain on it. Therefore, it is necessary to use a foil spacer or fix the part only with the upper part of the jaws.
Hand vice
It's portable compact tool, which does not require permanent fastening. Vices are used for processing small parts. There are two design options:
- with the presence of jaws along with a screw and handles;
- a lever vice resembling pliers with a locking mechanism.
They are used for precision work and are characterized by a minimal level of play. The design is adapted for manipulation with aluminum profile and metal tiles. They can be used to clamp flat workpieces.
At the same time, they are not suitable for working with large workpieces; additional elements when handling at an angle. When working with soft metals, marks remain on the workpiece.
Joinery construction
These vices are used in operations with wooden or plastic parts. The jaws are equipped with wooden linings, which eliminates the appearance of clamping marks. If the unit is mounted frontally, then it becomes possible to work with vertically fixed workpieces. Some models have a quick-release mechanism.
With all the advantages of other types of tabletop vices, the carpenter’s model allows high-quality processing of products from soft materials. Large parts are processed in one plane.
The sponge solution is quite large; there are several options for the fastening system. However, you will not be able to work with hard parts because the grip is not strong enough.
Features of choosing a device
You need to choose a design that suits you based on the parameters of the working elements:
- the size of the jaws, their width, the possibility of using overlays are factors that ensure stronger clamping of the part and quality of processing;
- the deep stroke of the clamping mechanism provides greater versatility and functionality;
- The presence of a margin above the height of the workpiece for inputting the part itself is also positively assessed;
- the handle should be comfortable and ergonomic - metal structure large diameter provides operator comfort.
How to work with a vice
When using a vice in work, you should not enlarge or otherwise extend the handle. Also, do not clamp hot steel products. Bending parts may damage the clamp itself.
If you are asking yourself the question of how to use a vice correctly, then you should not forget about the need for regular maintenance of the tool.
After each use, the vice should be wiped with solvent applied to soft cloth. All components must be regularly lubricated with machine oil to preserve them and prevent corrosion.
Popular and reliable manufacturers include Dexx, IRWIN, KRAFTOOL, Sturm, Wolfcraft, Zubr. Having chosen the appropriate model, do not forget to take an interest in the warranty and service conditions.
Photo of a vice
There is hardly a more necessary device in a home workshop than a bench vise. Even if you mostly work with wood, sometimes you won't be able to do without a vice. And if you don’t have a workshop, a garage or a corner in your apartment where you can repair simple household utensils, having a small benchtop bench vise can be a great help in many situations, turning kitchen table or even a stool for a mini-workshop.
First of all, about the purpose. The purpose of a vice is to securely fasten and hold a part or workpiece during processing. various instruments. Depending on what objects primarily need to be secured in a vice and what tools will be used to work with them, the design parameters of the vice vary. But the most universal and most common look like this:
The basis of any vice is a screw pair. In most cases, the screw is fixed in the movable part of the vice body, and the nut is fixed in the stationary part, which is either directly or through swivel mechanism It is attached to a mechanic's workbench or a special stand, which ensures that the vice remains stationary during any operations with the part fixed in it.
Types of bench vices
In addition to reliable support, you must clearly understand what types of work you will be doing and relate the choice of bench vise to them. First of all, this concerns the material of the case. In the post-Soviet space, it is often cast iron.
This material is hard, wear-resistant, but quite fragile. Therefore, if you are not going to bend thick steel workpieces with a sledgehammer without seriously preheating them, then feel free to take such a vice, and if you do, then it’s better to look for a steel one.
If you need to regularly fasten workpieces in such a table vise cylindrical, then it is advisable to make an overlay for the sponge with a triangular cutout. And if such operations are quite frequent, then we advise you to consider options design bench vice, slightly different from the standard ones.
In general, if we talk about the functionality of a bench vice, then first of all you should think about the size. If you know for sure that you will not have to work with large parts, then do not pay for extra metal, and perhaps even consider a compact machine vice.
Or vice versa - it is possible to work with large-sized parts, but without much effort when processing them. Then you can consider the option of a vice with the possibility of preliminary spreading the jaws without using lead screw.
If you do not have a workbench, and also the list of works includes more operations that do not require the use of rough physical strength to the workpieces, then the option with a table vice, secured using various clamps, is yours.
True, the latter are mini-tise, it is better to have them on the farm as additional ones. You can’t clamp large parts in them, and you can’t put any serious effort into the workpiece being processed - there’s not enough pressure on the clamp to hold the vise itself, but making a lock key based on a sample is just the thing.
In addition, such vices are sometimes indispensable if you need to unscrew a stuck nut, when you can use them as hand tools. Despite their miniature size, their jaw pressure is very good.
It is also worth mentioning a small vice on a ball joint, which serves for the convenience of processing very small parts of complex configurations, allowing for processing various surfaces parts from one fastening.
It is clear that the clamping force of the ball joint is not enough for serious physical loads, so such a vice is suitable for quite specific types of work. The same, in our opinion not very serious, will be vices with fastening using a suction cup.
To secure them more or less securely, you need either a well-polished surface or glass. It is unlikely that they will be securely attached to other surfaces. And their functionality is also limited.
For all types of bench vices, you will obviously need additional pads to secure parts made from soft materials.
Some bench vise They have a pneumatic drive, which greatly facilitates the process of securing the workpiece.
But if you don’t have a mini plumbing workshop at home, then you are unlikely to need such a vice.
What else is important to know when choosing a bench vise? There are quite a lot of complaints from users about Chinese vices with cast iron bodies, equipped with clamps for fastening - they often break off, so if you want a cheap vice from the Middle Kingdom, it is better to choose one made of steel.
Choose a vice that has the least amount of play between the body parts when the jaws are set as far apart as possible. Also, if you do not need a rotating mechanism at the base of the vice for work, choose a model without it: you will save money and the structure is more rigid.
How to make a bench vise with your own hands
The question arises: why, with such an abundance of sizes, shapes and configurations of bench vices offered by the retail chain, bother with them? independent execution. When making a bench vice with your own hands, you can save up to 10 times in cost, and also make a device with the specified parameters.
And this is absolutely real, because almost everything that can be useful for making a table vice can be found at scrap metal collection points for mere pennies.
This is especially noticeable in the photograph, in which parts of a plumbing pipe valve with a flywheel are used as a screw pair.
You can also take a screw pair from an old vertical jack. Even if part of the thread has already worn slightly, then, as a rule, this small area from the edge of the screw, which will still need to be trimmed to shorten it. The lead screws of old lathes, screw presses, etc. are also very durable.
At worst, for very little money you can order a turner at the nearest vocational school such a pair with a wide nut, with a regular metric thread. Just make the diameter larger and the nut wider. In this case, the clamping force will be redistributed over a sufficiently large area due to the diameter of the screw and the number of turns.
As a last resort, just buy a stud with a larger diameter from a store that sells hardware, and a tall nut for it, or 3 regular ones, which you then weld in series, screwed onto the stud.
The classic version of a homemade bench vise
The photograph clearly shows the steel parts, which can almost always be picked up without much difficulty at the nearest metal shop:
- steel plate 200 x 200, thickness 3 – 6 mm (thicker is possible);
- 2 channels (120 mm - external, 100 mm - internal) with a length of 160 mm and 300 mm, respectively; in your case, the dimensions may be different depending on the length of the lead screw;
- steel ears from some large container;
- 2 worn turning tools;
- rod for the wrench, in in this case piece of reinforcement;
- a screw or pin corresponding to the diameter of the rod, and 2 nuts;
- 2 washers, with a diameter corresponding to the diameter of the lead screw;
- screw pair - any of those described (in this case - ordered by a turner), 335 mm long;
- powerful plate for fastening the lead screw.
The lead screw on both sides of the plate is separated by washers, one of which, on the side of the threaded part, is welded to it, although with this diameter it can be secured with a cotter pin or retaining ring. Then this unit will be completely dismountable, which is clearly better for reasons of maintainability.
The handle on one side is sealed with a welded nut, and on the other side it is made collapsible after welding the thread from a screw of the appropriate diameter to it.
The nut from the screw pair is welded to the base plate flush with the 120 channel.
For normal fit of the inner channel with the lead screw attached to it, its ribs need to be lightly processed with a file.
The ears with jaws welded to them, made from cut turning tools, must be positioned with the lead screw screwed in. This way they will take the exact place. You can even twist the sponges together soft wire, ensuring their ideal relative position.
You can also first apply a notch to them using an angle grinder with a metal cutting disc.
Due to this type of fastening of the jaws, namely the shape of the hooks and the distance between them, non-standard parts that are widened towards the bottom can be fastened in such a vice.
Yes and maximum thickness The workpieces processed in these vices are quite impressive. And there is no need to talk about the maintainability of such equipment - you can see for yourself.
Dear readers, if you have any questions, please ask them using the form below. We will be glad to communicate with you;)
In order to understand what a vice is used for, it is worth considering the design of a vice for metalwork. They are used for strong and immovable fixation of parts. Without even a vice good master will be helpless. This tool has become indispensable both in the home workshop and in production. Behind long years the existence of the vice has undergone many changes, but the basic principle has remained unchanged - reliable fastening between sliding planes.
Bench vice is widely used in household and factory floors for reliable fixation of parts.
Structure of this tool
Vices are made in a variety of models and shapes. They are also used very widely, from households to factory floors.
Despite the diversity existing varieties such a tool as a vice, all these types of tools include the following parts:
- movable sponge;
- fixed sponge;
- screw clamp;
- spring;
- screw clamp handle;
- sleeve;
- mechanism for fastening to the workbench;
- replaceable pads.
Bench vices are made of carbon steel or gray cast iron. The device is attached to the table or to a specially designed stand with bolts or special clamps. Usually one of the jaws of the tool is fixed, which is called fixed. In turn, a movable sponge is attached to it in a certain way.
They are connected to each other by a screw with a straight thread. This part is driven by a handle. The process of rotating the screw brings the movable jaw closer or further away from the fixed one. Thanks to this, it becomes possible to hold one or another workpiece between the jaws. Typically, an anvil is located on the back of the device so that the processing capabilities of parts can be increased.
A certain type of device can be used depending on the nature of the task being executed.
Main types of this tool
Let's look at the most common bench vices.
- Chair vice. Typically, these types of vices are used when it is necessary to perform hard work where you need to beat, rivet, bend, etc. They are called that because their mounting looks like a chair. Initially they were attached to a wooden base.
Later they were adapted for installation on metal workbenches. The design difference from other clamping devices is that the fixed jaw is attached in two places. It is attached to the horizontal plane using a special strip called a foot, and the lower, elongated part can be attached to the leg of a table or workbench.
This fastening method makes them resistant to strong side impacts. The other sponge is movable. By tightening the clamping screw, the vice holds a particular part with both jaws. Unscrewing is accompanied by the fact that, under spring pressure, the movable jaw facilitates the action of the vice on the workpiece. To prevent the vice from bending and breaking, they are not cast, but forged from special carbon steel.
The width of the jaws can be changed and used depending on the size of the vise. Typically, jaws of 100 mm, 130 mm, 150 mm, 180 mm are used. Also, chair vices are divided according to other characteristics, for example, this classification depends on largest size parts that can be processed. There are several types with jaw openings of 90 mm, 130 mm, 150 mm and 180 mm.
The working parts of the vice are plates located in the upper part of the jaws in special recesses.
The plates are forged, and notches are made on one of the surfaces to firmly grip the part. They are either welded to the jaws of the plate or secured with bolts. To do this, holes are made in the plates with recesses for the bolt heads.
Chair vices have both advantages (ease of fastening and reliability) and disadvantages. This type of tool is designed for working with rough materials and is completely unsuitable for fine workmanship. The fact is that the clamping plates of the jaws are not always parallel to each other and, when clamping, cut into the part and damage its surface with dents.
This design allows you to clamp thin parts only with the upper edges of the pads, and thick parts only with the lower parts. This reduces the clamping strength. To avoid this, tighten the screw more. The surface of the workpiece may not withstand this force.
There are so-called parallel vices. Or rather, it would be necessary to say, with parallel jaws. In this design they tried to correct the lack of chair vices. This type of clamping mechanisms has become the most used and convenient to use. They are made of cast iron and special elastic carbon steel. Before purchasing or starting to work with a vice, it is advisable to understand what this unit is made of. Products made of cast iron are more fragile and require special handling. Cast iron doesn't like impacts. In addition, heated parts should not be processed on metalworking machines. When cooling, the size of the workpiece changes, which can lead to injury to the master.
Types of parallel vices
This type of bench vise is divided into stationary and rotary.
A fixed vice is attached to a workbench and can only be used in one position. To change the angle of the workpiece, you need to loosen the screw clamp using the clamping screw, change the position of the workpiece and clamp it again with the jaws.
To avoid constant changes in the position of the part, a tool of this type with a rotating base was invented. They are designed in this way: the base of the vice is rigidly attached to the workbench. The rotating part of the fixed jaw is attached to it using an adjusting screw with a handle. By loosening this screw, the vise can be rotated around a vertical axis. Various models turn to different angle- from 60 to 360°.
A hole is made in the stationary sponge rectangular shape, where the pressure screw of the movable jaw is inserted. Moving in this hole with the help of a screw, the jaws bring the clamping pads closer and further away strictly parallel to each other. This clamping method allows complete control of the workpiece.
Since the body is made of cast iron, to increase the service life of the tool, the linings are made of steel. They are attached to the upper parts of the jaws using bolts. On work surface The linings are notched for a tighter clamping of the workpiece. When to do it finishing, soft metal plates are placed on steel plates. They protect the part from dents and scratches.
Pros and cons of these tools
Most often in practice, parallel rotary and non-rotary instruments with a rear fixed jaw and a front fixed jaw are used.
Along with the indicated advantages of such a vice, there is a significant drawback - the weak strength of the jaws. This is why tools of this type are not suitable for difficult work. For small and precise work They make vises, which are sometimes called hand vises, with jaw sizes of 35 mm, 40 mm, 50 mm and 56 mm. They open to 28 mm, 30 mm, 40 mm, 50 mm and 55 mm, respectively. They are designed on the same principle as a chair vice. The part is fastened between the lips with a screw with a rotary wing, and for unclamping, in addition to the screw, a spring made of carbon steel grade U7 or grade 65G is installed between the jaws.
Use hand vices to fasten parts while holding them with both hands (both or one). They are used when the workpiece is inconvenient or dangerous to hold in your hands. In order to work with small parts with both hands more accurately, clamp the hand vise into a regular vise located in parallel.
Another type of bench vice is a pipe vice. The flat working pads of a conventional vice are not able to firmly clamp a round-shaped part. The contact area of the linings with the pipe is very small and it becomes almost impossible to process it. Such tools are specially created for this purpose. The concave shape of the jaws allows you to tightly clamp a pipe or other round part.
When fastening parts, it is not recommended to increase the clamping force using additional attachments to the screw handle. You should not put a pipe on the handle or replace it with a longer steel rod. The original handle is designed specifically for clamping by hand, so if the load increases, the tool can be damaged.
- Pneumatic vice with hydraulic power steering.
- Self-centering machine vice.
- Rotary machine vise.
- Machine vices, rotating and non-rotating.
- Pneumatic machine vices.
- Modernized bench vices
(professional) TSM.
CAST IRON MACHINE VICE (BZSP).
Non-rotating cast iron machine vice.
Cast iron machine vice
Vice accuracy class N and P according to GOST 16518.
- Installation of the vice on the machine table is carried out using keys, fastening - using bolts.
Characteristics of fixed cast iron machine vice:
Model |
IN Width of jaws mm |
A Sponge consumption mm |
B1 Width, mm |
L Length, mm |
N Height, mm |
h, mm |
b, mm |
b1, mm |
C, mm |
An effort clamp, N |
Weight, kg |
Price, rub. |
7200-0209-02 | 125 | 130 | 176 | 349 | 105 | 47 | 14 | 14 | 150 | 20000 | 13 | 11 100 |
7200-0214-02 | 160 | 200 | 176 | 424 | 114 | 50 | 14 | 14 | 150 | 25000 | 19 | 13 800 |
7200-0219-02 | 200 | 250 | 251 | 546 | 146 | 65 | 18 | 18 | 210 | 35000 | 41 | 19 400 |
7200-0219-04 | 200 | 250 | 250 | 521 | 141 | 66 | 18 | 18 | 210 | 35000 | 32 | 18 900 |
7200-0224-03 | 250 | 320 | 326 | 644 | 183 | 80 | 18 | 18 | 280 | 45000 | 72 | 28 200 |
7200-0224-04 | 250 | 320 | 316 | 641 | 172 | 80 | 18 | 18 | 280 | 45000 | 54 | 23 800 |
7200-0227-02 | 320 | 400 | 382 | 780 | 197 | 100 | 22 | 22 | 340 | 55000 | 96 | 36 400 |
Cast iron rotary machine vice.
7200-0204-13, 7200-0206-13 |
Characteristics of rotary cast iron machine vice:
Model |
IN Width of jaws mm |
A Sponge consumption mm |
B1 Width, mm |
L Length, mm |
H1 Height, mm |
N, mm |
h, mm |
b, mm |
b1, mm |
n | An effort clamp, N |
Weight, kg |
Price, rub. |
7200-0210-02 | 125 | 130 | 198 | 396 | 132 | 105 | 47 | 14 | 14 | 2 | 20000 | 17 | 13 800 |
7200-0215-02 | 160 | 200 | 198 | 472 | 141 | 114 | 50 | 14 | 14 | 2 | 25000 | 23 | 17 100 |
7200-0220-02 | 200 | 250 | 275 | 598 | 180 | 146 | 66 | 18 | 18 | 2 | 35000 | 51 | 23 900 |
7200-0220-04 | 200 | 250 | 270 | 548 | 171 | 136 | 66 | 18 | 18 | 35000 | 38 | 22 000 | |
7200-0221-02 | 200 | 250 | 275 | 598 | 180 | 146 | 66 | 18 | 18 | 4 | 35000 | 56 | |
7200-0225-03 | 250 | 320 | 340 | 709 | 223 | 183 | 80 | 18 | 18 | 2 | 45000 | 92 | 36 000 |
7200-0225-04 | 250 | 320 | 336 | 709 | 204 | 168 | 80 | 18 | 18 | 45000 | 65 | 29 200 | |
7200-0226-03 | 250 | 320 | 338 | 709 | 223 | 183 | 80 | 22 | 22 | 4 | 45000 | 96 | |
7200-0229-02 | 320 | 400 | 400 | 780 | 233 | 197 | 100 | 22 | 22 | 4 | 55000 | 116 | 43 300 |
Pneumatic vice with hydraulic reinforcement, rotating.
Pneumatic machine vice with hydraulic reinforcement designed for securing parts when machining metals by cutting on milling, planing, drilling and other machines.
- Vice accuracy class N and P according to GOST 16518 (DIN 6370).
- The body parts of the vice are made of cast iron.
- Installation of the vice on the machine table is carried out using keys, fastening using N grooves b1.
- The workpiece is clamped using a package of disc springs, which are pre-compressed by a power mechanism. The power mechanism is a built-in pneumatic hydraulic booster.
- Clamping the workpiece with disc springs ensures the safety of fastening parts when the air pressure in the network completely drops. Nominal air pressure 0.6 MPa.
Characteristics of rotary cast iron machine vise with hydraulic boost:
Model |
IN Width of jaws mm |
A Sponge consumption mm |
h, mm |
A1, mm |
L Length, mm |
B1 Width, mm |
N Height, mm |
b, mm |
b1, mm |
n | An effort clamp, N |
Weight, kg |
Price, rub. |
7201-0009-02 | 160 | 200 | 50 | 4 | 521 | 280 | 176 | 14 | 14 | 2 | 30000 | 52 | |
7201-0014-02 | 200 | 250 | 65 | 4 | 640 | 325 | 210 | 18 | 18 | 2 | 40000 | 88 | 60 300 |
7201-0019-02 | 250 | 320 | 80 | 6 | 720 | 338 | 240 | 18 | 18 | 2 | 50000 | 120 | 71 900 |
7201-0020-02 | 250 | 320 | 80 | 6 | 720 | 338 | 240 | 18 | 18 | 4 | 50000 | 120 | 79 000 |
STEEL MACHINE VICE (BZSP).
Non-rotating steel machine vice.
Non-rotating steel machine vice With manual drive designed for securing workpieces during machining on metal-cutting machines.
Vice accuracy class "P" according to GOST 16518.
- The body parts of the non-rotating vice are made of steel with heat-treated guides. Installation of the vice on the machine table is done using keys, fastening - using clamps.
- Setting the vice to right size is done by fixing the bracket located inside the slider with a pin into the holes of the housing.
- The high hardness of the working surfaces ensures the durability of the vice while maintaining accuracy.
7202-0202-02, 7200-0205-02. |
7202-0209-05, 7200-0214-02, 7202-0219-05. |
X characteristics of steel fixed machine vices 7200-0203-02, 7200-0205-02, 7200-0209-02, 7200-0214-02, 7200-0219-02:
Model |
IN Width of jaws mm |
A Sponge consumption mm |
h,
mm |
H Height, mm |
L Length, mm |
D, mm |
b, mm |
An effort clamp, N |
Weight, kg |
Price, rub. |
7200-0203-02 | 80 | 50 | 30 | 65 | 220 | 190 | 12 | 6000 | 5 | 10 400 |
7200-0205-02 | 100 | 80 | 35 | 72 | 305 | 272 | 12 | 10000 | 10 | 12 600 |
7200-0209-05 | 125 | 125 | 45 | 110 | 407 | 14 | 30000 | 25 | 28 700 | |
7200-0214-05 | 160 | 200 | 50 | 120 | 520 | 14 | 50000 | 36 | 32 800 | |
7200-0219-05 | 200 | 250 | 65 | 153 | 630 | 18 | 55000 | 67 | 48 100 |
Steel rotary machine vise.
7200-0204-02, 7200-0206-02. |
7200-0210-05, 7200-0215-05, 7200-0220-05. |
Characteristics of steel rotary machine vices 7200-0204-02, 7200-0206-02, 7200-0210-05, 7200-0215-05, 7200-0220-05:
Model |
IN Width of jaws mm |
A Sponge consumption mm |
h,
mm |
IN 1 Width, mm |
H 1 Height, mm |
L Length, mm |
D, mm |
b, mm |
H, mm |
An effort clamp, N |
Weight, kg |
Price, rub. |
7200-0204-02 | 80 | 50 | 30 | 134 | 90 | 220 | 190 | 12 | 65 | 6000 | 7 | 14 400 |
7200-0206-02 | 100 | 80 | 35 | 156 | 97 | 305 | 272 | 12 | 72 | 10000 | 12,5 | 18 500 |
7200-0210-05 | 125 | 125 | 45 | 200 | 145 | 465 | 14 | 110 | 20000 | 29 | 35 800 | |
7200-02 1 5-05 | 160 | 200 | 50 | 245 | 160 | 524 | 14 | 120 | 25000 | 50 | 41 400 | |
7200-0220-05 | 200 | 250 | 65 | 315 | 194 | 635 | 18 | 153 | 35000 | 86 | 58 700 |
Self-centering vice designed for securing workpieces during machining on metal-cutting machines.
Characteristics of steel fixed self-centering machine vice:
Model |
IN Jaw width, mm |
A Sponge consumption, mm |
h, mm |
H, mm |
C, mm |
L, mm |
An effortclamp, N |
Weight, kg |
Price, rub. |
7200-0209-12 | 125 | 125 | 45 | 110 | 418 | 366 | 20000 | 30 | 67 100 |
7200-0219-12 | 200 | 210 | 65 | 198 | 613 | 700 | 35000 | 90 | 124 700 |
MACHINE VICE ("Metalist", Glazov, Russia).
TU396131-03-02962743-94.
Rotary machine vice 7200-32.
Fixed machine vice 7200-02.
Characteristics of machine vice 7200-32 rotary:
7200-3208 (A=80) |
7200-3210 (A=125) |
7200-3213 (A=200) |
7200-3218 (A=250) |
7200-3223 (A=320) |
7200-3228 (A=400) |
|
Width of jaws, mm | 100 | 125 | 160 | 200 | 250 | 320 |
Sponge stroke, mm ±10 | 80 | 125 | 100 200 |
125 250 |
160 320 |
200 400 |
Clamp height, mm | 40 | 40 | 50 | 65 | 80 | 100 |
Clamping force, daN, not less | 2000 | 2000 | 2500 | 3500 | 4500 | 5500 |
Keyway depth, mm | 4 | 4 | 4 | 6 | 6 | 6 |
Keyway width, mm | 14 | 14 | 14 | 18 | 18 | 18 |
Lead screw square side, mm | 14 | 14 | 19 | 19 | 19 | 19 |
40 | 40 | 45 | 45 | 45 | 45 | |
Weight, kg | 16 | 17 | 27 29 |
33 34 |
55 60 |
74 83 |
Length, mm, no more | 325 | 370 | 385 475 |
440 555 |
515 655 |
560 765 |
Width, mm, no more | 280 | 280 | 320 | 320 | 400 | 460 |
Height, mm, no more | 135 | 135 | 148 | 163 | 190 | 210 |
Characteristics of machine vice 7200-02 fixed:
7200-0207 (A=80) |
7200-0209 (A=125) |
7200-0214 (A=200) |
7200-0219 (A=250) |
7200-0224 (A=320) |
7200-0227 (A=400) |
|
Width of jaws, mm | 100 | 125 | 160 | 200 | 250 | 320 |
Sponge stroke, mm ±10 | 80 | 125 | 200 | 250 | 320 | 400 |
Clamp height, mm | 40 | 40 | 50 | 65 | 80 | 100 |
Clamping force, daN, not less | 2000 | 2000 | 2500 | 3500 | 4500 | 5500 |
Keyway depth, mm | 5 | 5 | 10 | 12 | 17 | 17 |
Keyway width, mm | 14 | 14 | 14 | 18 | 18 | 18 |
Side of the lead screw square, mm | 14 | 14 | 19 | 19 | 19 | 19 |
Lead screw square length, mm | 40 | 40 | 45 | 45 | 45 | 45 |
Weight, kg | 10,5 | 11,5 | 21,5 | 26,5 | 49 | 68 |
Length, mm, no more | 325 | 370 | 475 | 555 | 655 | 765 |
Width, mm, no more | 180 | 180 | 210 | 210 | 280 | 340 |
Height, mm, no more | 110 | 110 | 115 | 130 | 155 | 185 |
MACHINE VICE (manufactured by the Gomel plant, Belarus).
GOST 16518-96.
Rotary machine vise.
GM-7216P (7200-0215-02), GM-7212-02P, |
GM-7220P (7200-0220-02) |
GM-7225P (7200-0225-03), GM-7232P-02, GM-7225N (7200-0224-03), GM-7232N-02. |
1 - body, 2 - movable jaw, 3 - rotary plate.
Fixed: Rotary:
GM-7212N, 7216N, GM-7220N,GM-7225N, GM-7232N. GM-7212P, GM-7216P, GM-7220P,
GM-7225P, GM-7232P.
Characteristics of ROTARY machine vices:
Model |
Designation according to GOST |
Width sponges, mm |
The course of the sponges no less mm |
Worker height space, mm |
An effort clamp, kgf |
Weight, kg |
Height vice, mm |
Price , rub. |
GM-7212P | GM-7212P-02 | 125 | 150 | 47 | 2 500 | 18 | 120 | 8 400 |
GM-7216P | 7200-0215-02 | 160 | 250 | 55 | 3 500 | 29 | 145 | 11 700 |
GM-7220P | 7200-0220-02 | 200 | 300 | 80 | 3 500 | 44 | 190 | 13 700 |
GM-7225P | 7200-0225-02 | 250 | 300 | 80 | 4 500 | 61 | 190 | 18 900 |
GM-7232P | GM-7232P-02 | 320 | 400 | 100 | 5 500 | 138 | 215 | 30 300 |
Characteristics of machine vice WITHOUT ROTARY PLATE:
Model |
Designation according to GOST |
Width sponges, mm |
The course of the sponges no less mm |
Worker height space, mm |
An effort clamp, kgf |
Weight, kg |
Height vice, mm |
Price , rub. |
GM-7212N | GM-7212N-02 | 125 | 150 | 47 | 2 500 | 14 | 91 | 7 300 |
GM-7216N | 7200-0214-02 | 160 | 250 | 55 | 3 500 | 21 | 120 | 9 400 |
GM-7220N | 7200-0219-02 | 200 | 300 | 80 | 3 500 | 33 | 190 | 10 800 |
GM-7225N | 7200-0224-02 | 250 | 300 | 80 | 4 500 | 52 | 190 | 15 800 |
GM-7232N | GM-7232N-02 | 320 | 400 | 100 | 5 500 | 100 | 175 | 25 500 |
PNEUMATIC MACHINE VICE with hydraulic reinforcement.
Characteristics of machine vice GM-7201-0019-02:
FITTING VICE (manufactured by the Metalist plant, Glazov).
Bench vices TSS and TSSN series.
TSS TSSN
Bench vices TSS and TSSN series designed for securing workpieces when performing metalwork operations, there is an anvil on the body, the presence of prisms allows clamping round blanks, and the design of the base allows you to rotate the vice from 0° to 120°.
Material of body parts - steel 35L
Characteristics of bench vices TSSN63S, TSS80, TSS100, TSS125, TSS140, TSS160, TSS180, TSS200:
TSSN-63-S | TSS-80 | TSS-100 | TSS-125 | TSS-140 | TSS-160 | TSS-180 | TSS-200 | |
Width of jaws, mm | 63 | 80 | 100 | 125 | 140 | 160 | 180 | 200 |
Clamping force, kgf | 1000 | 1500 | 2000 | 2500 | 3000 | 3500 | 4200 | 5200 |
40 | 50 | 70 | 80 | 95 | 90 | 90 | 90 | |
Slider stroke length, mm | 80 | 100 | 140 | 160 | 180 | 160 | 160 | 160 |
Weight, kg | 3,7 | 4,6 | 11,4 | 13 | 14 | 26,5 | 26,5 | 28,0 |
Base length, mm, no more | 230 | 255 | 345 | 380 | 415 | 450 | 450 | 450 |
Basic width, mm, no more | 63 | 135 | 190 | 190 | 190 | 227 | 227 | 227 |
Base height, mm, no more | 200 | 120 | 160 | 175 | 190 | 210 | 210 | 210 |
Modernized (professional) metalworking vices of the TSM series.
Bench vice modernized (professional) TSM series designed for securing workpieces when performing metalwork operations. The advantage of the new type of vice: it allows you to clamp long workpieces in a vertical position, round ones - in the prisms of the body and slider. Due to the new design of the base, the vice can be rotated to any angle from 0° to 360°. The body of the vise has an enlarged anvil, and a thrust bearing on the screw facilitates clamping of the workpiece. The presence of adjusting screws in the body allows you to set the required gap between the slider guides and the supporting part of the screws as they wear out; the initial adjustment is made by the manufacturer. Fixed vices (without base) TSMN are manufactured upon request. |
Characteristics of the modernized professional bench vices TSM160, TSMN160, TSM180, TSMN180, TSM200, TSM200, TSM250, TSMN250:
TSM-160 | TSMN-160 | TSM-180 | TSMN-180 | TSM-200 | TSMN-200 | TSM-250 | TSMN-250 | |
Width of jaws, mm | 160 | 160 | 180 | 180 | 200 | 200 | 250 | 250 |
Clamping force, (kgf) | 3500 | 3500 | 4200 | 4200 | 5200 | 5200 | 5500 | 5500 |
Developmental moment,<=кгс/м | 14 | 14 | 20 | 20 | 25 | 25 | 25 | 25 |
Sponge stroke length, mm | 200 | 200 | 240 | 240 | 240 | 240 | 240 | 240 |
Working space depth, mm | 88 | 88 | 102 | 102 | 111 | 111 | 123 | 123 |
Weight, no more, kg | 21 | 20 | 28,5 | 26,5 | 37 | 35 | 55 | 52 |
Base length, mm | 487 | 487 | 555 | 555 | 555 | 555 | 595 | 595 |
Basic width, mm | 203 | 203 | 230 | 230 | 230 | 230 | 250 | 250 |
Base height, mm | 210 | 186 | 244 | 215 | 261 | 230 | 281 | 251 |
Price, rub. | 10 600 |
Bench vice cylindrical series TSC-180.
Characteristics of cylindrical bench vice TSC-180:
FITTING VICE (manufactured by the GMZ plant, Gomel).
Certificate No. ROSS BY.MM03.B02012.
Bench vice rotating steel TSS.
TSS-125, TSS-140. TSS-150, TSS-160, TSS-180, TSS-200.
1 - movable jaw, 2 - body, 3 - rotary plate, 4 - handle.
Bench vice rotating steel TSS produced by the GMZ plant are intended for securing workpieces when performing metalwork operations; there is an anvil on the body, the presence of prisms allows you to clamp round workpieces, and the design of the base allows you to deploy the vice. Material of body parts - steel 35L
Characteristics of steel rotary bench vices ТСС125, ТСС140, ТСС150, ТСС160, ТСС180, ТСС200:
TSS-125 | TSS-140 | TSS-150 | TSS-160 | TSS-180 | TSS-200 | |
Width of jaws B, mm | 125 | 140 | 150 | 160 | 180 | 200 |
Clamping force, kgf | 3000 | 3000 | 5000 | 5000 | 5000 | 5000 |
70 | 70 | 75 | 75 | 75 | 75 | |
Slider stroke length A, mm | 120 | 120 | 160 | 160 | 160 | 160 |
Weight, kg | 13,0 | 13,5 | 18,0 | 18,0 | 18,5 | 19,0 |
Length L, mm | 360 | 360 | 390 | 390 | 390 | 390 |
Width B, mm | 180 | 180 | 230 | 230 | 230 | 230 |
Height H, mm | 170 | 170 | 180 | 180 | 180 | 180 |
price, rub. | 4 100 | 4 400 | 7 100 | 7 300 | 7 600 | |
Bench vice rotating cast iron TSCH.
Bench vice rotating cast iron TSCh designed for securing workpieces when performing metalwork operations, there is an anvil on the body, the presence of prisms allows you to clamp round workpieces, and the design of the base allows you to unfold the vice. The material of the body parts is SCh20 cast iron.
Characteristics of cast iron rotary bench vices TSCh125, TSCh140, TSCh150, TSCh160, TSCh180, TSCh200:
TSCH-125 | TSCH-140 | TSCH-150 | TSCH-160 | TSCH-180 | TSCH-200 | |
Width of jaws B, mm | 125 | 140 | 150 | 160 | 180 | 200 |
Clamping force, kgf | 3000 | 3000 | 3000 | 5000 | 5000 | 5000 |
Working space depth h, mm | 75 | 75 | 75 | 85 | 85 | 85 |
Slider stroke length A, mm | 110 | 110 | 110 | 155 | 155 | 155 |
Weight, kg | 16,5 | 17,0 | 17,0 | 27,0 | 27,5 | 28,0 |
Length L, mm | 385 | 385 | 385 | 460 | 460 | 460 |
Width B, mm | 180 | 180 | 180 | 210 | 210 | 210 |
Height H, mm | 200 | 200 | 200 | 210 | 210 | 210 |
price, rub. | 3 500 | 3 700 | 5 400 | 6 000 | 6 200 | 6 500 |
Metalsmith's cast iron vice TSCh non-rotating.
TU RB 490175790.001-2003.
Characteristics of cast iron fixed bench vice TSCh250N:
IN Width of jaws mm |
A Sponge stroke, mm |
h Clamp height mm |
An effort |
L Length, mm |
B1 Width, mm |
H Height, mm |
Weight, kg |
Price, rub |
|
TSCH-250N | 250 | 200 | 80 | 6000 | 530 | 150 | 200 | 41 | 10 400 |
Material cast iron SCh20.