Spinners made at home. Spinner at home

The spinner is a fashion toy invented in the USA. It appeared in Russia in 2016 and has already gained extraordinary popularity. What is it? She is called a spinner, a spinner, a fidget.

It develops fine motor skills of the fingers, relieves anxiety and has an anti-stress effect. Fidget spinner is not only a toy designed to entertain children and adults. This is a great way to spend time waiting, traveling in public transport, and queuing. This turntable also allows you to get rid of bad habits, such as tapping your fingers on the table surface, repeating hand movements, and even the habit of smoking. It will allow you to get rid of the bad habit of twisting something in your hands. The working principle of the fidget spinner is the use of a bearing in the middle of the product with petals.

The fitget has two, three, four, five, and some models even six petals. The most common are toys.
The spinner is made of wood, brass, bronze, plastic, and can be combined.

Two types of bearings are used: metal, like, or with ceramic balls. Characterized by rotation time. The spinner rotates from one minute to several tens of minutes. The longer the rotation occurs, the better the quality of the toy.
The cost of the product is influenced by the use of high-quality materials in the manufacture of the body with petals. The easiest way to buy a spinner is in.

Making wood in a home workshop

However, a person familiar with tools can make such a toy for himself. For this you will need:

A small piece of wood, preferably hardwood;
Bearing (suitable for a broken skateboard);
Sleeves or suitable pieces of round metal;
Epoxy adhesive.

Video with instructions for making a spinner from wood

First of all, we mark out a piece of wood. A square piece is required.
We drill a hole in the center and expand it to fit the external dimensions of the bearing. The thickness of the workpiece must be equal to the thickness of the bearing. The next step is to insert the bearing and glue it with glue.
On two opposite sides we drill two holes equal to the smaller diameter of the sleeves. Then we take the polished sleeves, glue them in pairs and mount them with glue in the prepared holes of the board. Let the glue dry.
We clean, sand and paint in the color you like. A simple spinner with two petals is made at home. In the same way, you can make a homemade gadget from plexiglass or PCB.
It is more difficult to make a product with three petals. To do this you will need a drawing, a jigsaw and a protractor. The diagram below clearly illustrates how to make such a toy.

Paper spinner

It is much easier to make a hand-held spinner from paper.
We print the drawing on a regular printer.
Transfer the drawing to thick paper or cardboard.
We cut out 15-20 samples according to the template. Using scissors, we make a hole for the bearing, slightly smaller than the outer diameter.
Glue the cut out samples with PVA glue.
Place under the press.
After the glue has dried, insert the bearing.
We clean it with scissors and, if necessary, sandpaper.
Paint it in the desired color. The toy is ready.

Video with instructions for making a paper spinner without a bearing at home

As you can see, the cost of the product consists mainly of our own work, because Parts from out-of-circulation mechanisms were used for production.
Before assembling the gadget, inspect the bearing. To do this, remove the anthers and wash them. This completes the work on making the turntable.

Luminous

The most interesting toys come from making them yourself from absolutely incredible materials. Make a glowing fitjet - all you need to do is buy a phosphor online in China.
Dilute 3 grams of powder in 7 ml of glycerin to obtain a luminous liquid.
Then you can use the described method for making the central part from wood. Just use glass bulbs from fluorescent lamp starters instead of sleeves.
We pump liquid into the flasks using a syringe and glue them into the prepared holes.

It turns out to be a beautiful toy that you can play with and surprise your friends in the dark.

Made from chocolate

Any material you can imagine is suitable for making a spinner. It can be made from wax, paraffin candles, ice and even made edible.
A very original gadget is made from chocolate.

I played and got tired of it and ate it.

To make such a toy you will need:

Make a mold for filling;
Bearing;
Candies such as confetti or jelly beans;
Cardboard, for form and glue;
Wax paper;
Scissors with pencil;
A piece of foil from a chocolate bar and the chocolate itself;
Glue.

Video showing how to make an edible chocolate spinner

A drawing is taken from which the twist template is cut out. A strip slightly larger than the thickness of the bearing is cut out of paper and glued along the perimeter of the template.
Then we completely wrap the prepared bearing in foil and place it in the center of our mold, having previously placed wax paper on the bottom of the mold. We place candies along the edges of the petals (you can do without candies, this is for beauty). All that remains is to dissolve the chocolate in a water bath.
As soon as the chocolate becomes liquid, it is poured into the mold using a pastry syringe. It is necessary to pour very carefully so as not to move the installed parts.
After filling everything with chocolate, place the toy in the refrigerator. After some time, the chocolate will harden and can be removed from the refrigerator.
All that remains is to remove the product from the mold, free the bearing from the foil, clean the edges - and you can use it. When you get tired of it, you just have to eat it.
The entire manufacturing process can be filmed and shown to friends or posted on the Internet on your page.
In a similar way, a fitjet can be made at home from any hardening material: stearin, wax, gelatin, and from colored wax candles you can get a multi-colored spinner body.

They differ in the number and shape of the petals. The shape can be completely different: from geometric shapes to exotic and futuristic shapes. They differ in the use of bearings: one, three, four or no bearing at all. When choosing a spinner, follow these rules:

The gadget should rotate smoothly and without noticeable beats.
The quality of workmanship should not cause any complaints.
The material from which the toy is made must be of high quality.
The rotation is quite long: the longer the better.

Some users advise choosing products based on their preferences. If you like the item in terms of design, color, or manufacturing, buy it, but the rotation time is secondary.
So we see that no one can give an unambiguous recommendation. Focus on your own feelings. To ensure that the pinwheel serves for a long time and is always attractive, follow the recommendations:
Protect the toy from mechanical damage, falling from a height onto a hard surface;
If the product is made of plastic, it is not recommended to disassemble it, especially the button - the plastic parts can be damaged; they are glued or pressed in very tightly;
Periodically wash and lubricate the middle bearing using a syringe with a needle. Wash with gasoline, preferably for lighters, it has almost no odor. It is recommended to lubricate with watch oil in a small amount. Mineral oils should not be used for lubrication.

Reading time ≈ 6 minutes

More recently, the market for modern youth gadgets was blown up by an anti-stress toy called a spinner. Despite the large assortment of products offered on store shelves and online resources, the option of creating a spinner with your own hands looks very attractive, since it will not only save on the product, but also get the desired spinner according to your ideas and imagination. There are many options for making a spinner with your own hands at home, let’s look at the most popular ones.

What is a spinner?

The original name of the toy - fidget spinner - comes from the English word spinner, which means rotation or torsion. It consists of one or several bearings, which by their rotation help not only pass the time, but also improve finger motor skills, dexterity and attentiveness. An analogue of a spinner can be called the good old yo-yo, which in the early 2000s could be found in the hands of everyone. Now one of the most popular places among fashion trends is occupied by spinners, and various championships are already held based on the dexterity of handling them.

What is a spinner for?

The original purpose of the spinner was a toy for young people, a trinket that helps pass the time, but over time this spinner has turned into something more. As practice shows, a spinner is an excellent assistant in the fight against bad habits. This applies to quitting smoking, snapping fingers and many other unpleasant moments associated with the fact that a person urgently needs to occupy his hands with something. As a result, spinning a spinner has become a real hobby for many people who not only master the skill of spinning a toy, but also compete with each other in this aspect.

How the toy works

The main task of this product is its rotation, which should be continuous and occur without much effort. The basis that gives the toy rotation is the bearing, which is located in the center. In order for the spinner to spin for a long time and beautifully, it must have the correct shape and a reinforcing load. Typically, three weights are used, evenly spaced from the center, however, you can often find spinners with two or four weights. IMPORTANT to note that spinners do not require batteries to spin. If the toy is made correctly, a slight flick of the finger can make it rotate around its central axis. The most important thing in the normal operation of the spinner is maintaining symmetry, because even a slight deviation in the size of the sides with weights will lead to poor and unstable rotation.

How to make a spinner with your own hands?

Manufacturing this twister is not a complex technological process that requires special knowledge and tools. The main material is one or more bearings, and there are many options for making the base. The main nuance of this process is the weighting of the edges of the spinner, because otherwise it will not rotate well. Coins, nuts or other bearings are perfect for weighting. An IMPORTANT detail for hand spinners is bearing lubrication, which allows you to increase the rotation speed of the toy several times. It is recommended to lubricate with oils intended for motorcycle chains. If you don't have one on hand, you can use WD-40.

Wooden spinner

In order to decide on the question of how to make a spinner with your own hands, you first need to decide on the base material. Cool spinners are made from a wooden base, which, if processed correctly and with high quality, is not much different from factory analogues. First you need to create a drawing of the future product. It should be based on the diameter of the bearing and three weights, based further on these numbers. After transferring the sketch from paper to a wooden blank, you need to cut out the future spinner using a jigsaw.

Holes for metal parts are drilled on a special machine or using a feather drill. For ease of use, the workpiece must be carefully ground and polished. The reliability of the finished toy will be ensured by fixing the metal parts to the base with epoxy or any other glue. In order to make it convenient to spin the spinner on your finger or any other surface, it is recommended to apply decorative pads to the rotating part of the bearing. From available materials, two ordinary buttons of the appropriate size are perfect for this role.

Spinner with 4 bearings

An attractive manufacturing option is to create a spinner from bearings with your own hands. Firstly, this method does not require various foreign materials, except for glue and four bearings, one of which will act as a central axis, and the other three as weighting agents. Secondly, this method does not require much time, allowing you to get a spinner in 5 minutes of work.

The only difficulty in the process is the poor adhesion of metal parts to each other. Reliable fixation will require additional heat treatment, which is often difficult to achieve at home. After gluing, excess glue should be removed with a file or needle file, thereby removing all rough surfaces.

Handmade spinner made from hot glue

Hot glue makes a great base for a DIY twist. For manufacturing you will need a set of weights, a bearing, hot glue and a base that acts as a flask (usually made of thick paper or cardboard according to the drawing).

An important point is to install the metal parts strictly in the center of their area. Then glue is poured into the mold and waits there to completely harden. After hardening, the paper outline is removed and the spinner is sanded to a completely smooth surface.

Epoxy glue toy

To make a homemade spinner, you can use not only hot glue, but also epoxy in a hardened form. Glue in the form of plasticine not only connects the bearing and weights, but also is the basis for torque.

In this manufacturing process, it is important to correctly position the metal parts; for this it is better to use a pre-marked wooden board with drilled holes and inserted clamps. It is better to remove the main excess glue before it has completely hardened, then sanding only minor roughness.

The simplest and most cost-effective option for making a spinner yourself is to work with plastic clamps that are designed to tighten cables. For ease of operation, it is recommended to use metal weights of the same diameter as the bearing. Weights are laid out at three corners of an equilateral triangle, as shown in the photo. Around them a base is created from three ties closed to each other. Then, each of the weights is attached to the base using a plastic clamp.

After this, an axial bearing is installed in the middle and uniform tightening of the clamps begins on the side of each weighting material. For reliable fixation, the resulting structure is tightened with three more clamps, from the center to each side of the weighting weights. Although this manufacturing method is the most inexpensive and fastest, the appearance of the finished product is significantly inferior to analogues made from other materials.

MDF spinner

Making spinners from medium-density fiberboard is very similar in principle to working with a wooden blank. At the beginning of the process, markings are applied on a small MDF sheet, taking into account the placement of metal parts and the overall size of the spinner. Then holes are drilled for the central bearing and weighting elements and the size is adjusted to be close to the final size.

It is worth noting that when processing and drilling MDF sheets you need to be more careful and careful than when working with wood, since this material is fragile and brittle. To impart an aesthetic appearance to the finished product, it is recommended to paint it; before painting, the spinner must first be sanded and degreased.

The spinner is a new fun toy that adults and children will enjoy. It appeared in America last year and in a short time gained enormous popularity. The principle of operation of the toy is simple: with the middle and thumb of one hand we grab the central bearing. With the other hand we activate the wings of the turntable. With sufficiently good control skills, you can operate the toy with one hand. Use your index finger and thumb to grasp the center bearing. The hand spinner consists of three parts: a housing, a bearing and a plug.

Advantages of a spinner

Hand motor skills develop, fingers become more sensitive. This tool will be very useful for those who have suffered various hand injuries.
This is a kind of anti-stress toy that calms the nerves. In addition, thanks to it, you can concentrate, restore efficiency, relieve anxiety and nervousness, and also become less irritable.
The spinner will be an excellent companion during a long trip; it can be a great way to occupy your free time.

LED spinner on the controller

Some people buy them, while others make them themselves. Here is a circuit diagram of a spinner with LEDs controlled by a microcontroller. When rotating, all sorts of pictures and signs are created.

Project Parts List:

MK ATtiny-45
5 smd led (1206)
5 smd resistor (47 ohm)
1 battery 16 mm (3 V)
22mm diameter bearing
A piece of wood or plastic

As you can see, the scheme is simple, but if anyone doesn’t understand something, study the datasheet from Atmel.

The positive LED leads go to PB0 - PB4 on the MK. To limit current, resistors are added between them. The negative contacts of the LEDs go to minus - GND.

There are different options for displaying the figures, so a browser page is made to create image sequences for the spinner. In the general file, the link to which was above, you will find the drawing, firmware and program.

Spinner with ball bearings

This spinner consists of a housing on bearings and a plug. The center bearing is the most important. The speed and time of rotation of the spinner depends on its quality. The plugs are inserted into the central hole.

One of the most accessible means at hand is paper and cardboard. A hand spinner is made from paper using a knife, four bearings, and glue. First you need to make drawings. Using a utility knife, cut out pieces from paper or cardboard. The holes for the bearings are cut with nail scissors or a knife. It is important to ensure that their diameter is slightly smaller than the diameter of the bearing. This is necessary to ensure that the bearings fit tightly into the holes. The number of parts depends on the width of the bearing. Gluing requires a lot of glue. it will give the product greater strength. After finishing the work, we paint the toy in any color.

To increase the moment of inertia, it is necessary to provide weights. The simplest option is coins glued to each other. For 10 mm plywood, you need to glue 8 ten-kopeck coins together. We level the internal surfaces of the workpiece using a drill. We carefully and quickly bring the outer surfaces to the contour using a grinder with a grinding wheel. We remove all remaining irregularities manually with sandpaper.

For those who know how to work with a jigsaw and drill, you can make a spinner out of wood. Wood is an environmentally friendly material. The product turns out beautiful and pleasant to the touch. First we choose durable wood. For beginners, it is better to use plywood. Working with wood requires skills. First prepare a drawing. You can come up with it yourself or simply print it from the Internet. Place the paper blank on the wood or plywood and trace it with a pencil. Cut out and sand the part with sandpaper. The hole can be cut out, but it is better to use a drill to make the hole even. An important point: use a drill to make a hole halfway on one side, and then turn the part over. This way you have a better chance of getting the perfect hole for the bearing. The thickness of the wood or plywood should be exactly the same as the bearing. If it is a little larger, it needs to be sanded.

Typically, a bearing from skateboard wheels, rollers or scooters is used. They have a standard size of 22 millimeters in diameter, the width and internal diameter can be selected at your discretion.

After experimenting with sizes, we came to the conclusion that the ideal size for long-term torsion is 25-27 mm in diameter. At the same time, for a spinner it is better not to take bearings smaller than 20 and larger than 30 mm.

Finger spinner will be a savior for those people who bite their nails, pens, or the like during stress. The fidget spinner is designed to relieve stress, warm up your fingers, as well as concentrate your attention and develop hand motor skills. Such a device will become an indispensable thing for children and adults.

The surface of the materials can be lumpy or smooth, and you can find a variety of color options: white, black, red and many others. The size of the toy is small, which allows you to carry it with you. The unusual and stylish design can make it an excellent accessory.

How to make a spinner with your own hands

Why do you need a spinner from a store if you can make it yourself? The whole process of work will take a little time, and its design is simple. In order to start tinkering, you will need:

Textolite;
furniture ties;
bearings;
drill and drill bits for it;
ruler, compass.

First you need to take the PCB and cut out the base for the spinner from it. First, using a compass, a drawing of the toy is drawn, and only then it is cut out. Before you start drawing the base, you need to find out the size of the bearing, for example, it is 22 mm, so the compass needs to be inserted into the PCB at 11 mm and draw a circle. After this, insert a compass at 18 mm and draw another circle. An individual calculation is required for each case. This is easy to do, all the variety of options are presented on the Internet, there are also stencils for the spinner.

Then we start working with bearings. Each of them needs to be wiped with resin, after which they can be connected to the block. Only after this can you drill holes for the sleeves. To do this, you need to mark six sectors of the spinner. Each intersection point of sectors and circles is the center of the sleeves. You need to drill holes in each intersection, exactly six pieces. Then you need to drill out the center of the spinner.

Each sleeve must be sanded before being inserted into the hole. This is very simple to do; to do this, you need to insert it into the drill chuck and rub it on sandpaper at the lowest speed until all the paint is removed from them. Each of the sleeves must be lubricated with the same resin and pressed in.

After all the steps are done, the toy needs time to dry. This will require a minimum of six hours, after which you can enjoy playing with the hand spinner.

Video - the coolest spinners

Has your child succumbed to the popular fashion for spinning spinners? Is he asking for a red one, a yellow one, and also a luminous one in the form of a minion? In general, so that it’s not like everyone else? Then you can make a toy with your own hands. Moreover, such a labor lesson will keep both you and your baby busy. And if you still don’t know what a spinner is, there we answered all the popular questions about this modern, arch-modern fun.

We have put together three ways for you to make a spinner, two easy and one more difficult (you'll need your dad's help here). But we are sure that both tools and materials should be found at home or in the country. Each instruction is supported by a video tutorial found on YouTube for clarity. So, how to make a spinner out of paper, plastic lids and wood?

Method 1. Spinner made of paper and cardboard.

Simple, cheap and not at all ugly - a paper spinner for beginner spinner makers. An older child can handle it on his own, a little one may need a little help, and the result can be proudly taken to kindergarten or school - where creativity is always held in high esteem.

What you will need:

Cardboard, marker and caps (or a ready-made template from the Internet)
Scissors
Nail scissors or awl
3 coins
Pen refill
Paints or glitter for decoration

Instructions:

Download a ready-made spinner template from the Internet. Or draw it yourself by tracing plastic bottle caps on cardboard. You need to cut two pieces of cardboard in the shape of a spinner.
Cut out four more smaller circles. You can circle a coin of a lower denomination.
Glue three coins of the appropriate size on the sides of one of the cardboard blanks.
Glue the other half on top of the blank with coins.
Using nail scissors or an awl, make a hole in the center of the spinner.
Cut about 1 centimeter off the shaft from the handle.
Punch holes in the center of two small circles.
You can paint the finished spinner blank in any colors or decorate it with sparkles, rhinestones or stickers with your child’s favorite characters. Everything is your choice and completely unique!
Insert a piece of dowel into one of the small circles and glue it around the edges of the hole.
Insert the circle with the rod into the center of the spinner and glue the second circle on the other side.
Glue the two remaining small circles on top of the ends of the rod. Ready! A spinner made of cardboard, without a bearing and with complete imagination in terms of design is sure to keep a child occupied for some time.

Source: PLASTILIN

Method 2. Spinner made of plastic caps.

This spinner will require a little more materials and diligence, but it will also last much longer. In general, a spinner made from Coca-Cola caps is something like crafts made from matchboxes for older generations. Dear consumables and soul-warming results with minimal costs for an actively functioning (that is, rotating) thing.

What you will need:

Plastic bottle caps
Kinetic sand or plasticine
Glue gun
Nail and lighter
Glue stick
Scissors
Toothpick

Instructions:

Place kinetic sand or plasticine into three bottle caps almost to the top. The main thing is to make the blades heavier.
Use a glue gun to fill the remaining space in the lids to the top.
Make a hole in the fourth (without sand) lid (you can use a heated nail).
Glue three lids with sand to the central lid with a hole.
Cut two pieces about 1 centimeter from the glue stick.
Break a toothpick in half. Place a piece of rod on one end (the toothpick should not stick out) and thread it into the center of the spinner.
Place the second piece of the rod over the tip of the toothpick on the other side. Ready! If you are very eager, such a spinner can also be decorated creatively - painted with paints (for example, acrylic) or pasted over with something positive. Or you can leave it as is, choosing interesting combinations of caps from bottled drinks.

Source: Feature of the Day

Method 3. Wooden spinner (with bearing)

Let's move on to the most labor-intensive method of making a spinner. You can’t do without parents here, but the result can be safely laid out on the desk along with purchased toys. Again, in terms of design, freedom for self-expression is provided. For those dads and children who are friends with a jigsaw, know how to find bearings on the shelves of hardware stores and know which side to hold the drill on.

What you will need:

2mm bearing
Plywood sheet (5 mm)
Stack of coins
Scissors
Pencil
Hand jigsaw
Sandpaper
Template (or cardboard and marker to create it)
Clamp
Drill

Instructions:

Glue the template onto a sheet of plywood and mark the locations for future holes in each of the circles.
Drill holes in each of the three circles on the sides to make it easier to cut them out later.
Insert a jigsaw into the holes and cut them out.
Cut out the workpiece itself from a sheet of plywood and sand it with sandpaper.
You can paint the spinner any color you like.
Insert the bearing into the central circle; if it does not fit well, you can drive it in with a hammer.
Glue together a stack of coins for the inner circles. Start with a five-ruble coin (put it under the circle), then two-ruble coins and on top again a coin with a face value of five rubles.
Do this for all circles. You can decorate it on top as you wish. Ready! Just think about the benefits of a homemade anti-stress toy: you had a good time together with your child, worked hard and saved money on buying another plastic trinket. And it spins great!

Do you want to buy a spinner, but it is not on sale in your city? We will tell you how to make a spinner with your own hands without a bearing! Recently, an unusually large number of newfangled toys have begun to appear. They are great for both children and adults, but sometimes it is very difficult to find a store that can sell you such a newfangled accessory. We'll talk about spinners.

This toy became a trend relatively recently and simply flooded the Internet. It is impossible to purchase it in some cities, since there are no retail stores, so you have to order it online.

But why spend money if you can do it yourself?! Many people wonder how to make a spinner without using a bearing, today we will help you with this.

What is a spinner

The word "spin" is translated from English as "rotation". By and large, the toy is a rotating body that moves around its axis when energy is imparted to it. You can get a spinner without bearings, but it will not have the required rotation speed.

A standard spinner consists of three petals, with a bearing located in the center of each. It is worth noting that the mass of each petal must be the same, as well as the shape, otherwise there will be no balance and the rotation will stop very quickly.

What's the catch?

In our free time, when we are waiting for something, when we are thinking, we always take something in our hands in order to somehow entertain or calm ourselves. For this you need... a spinner. Of course, you can’t call it a children’s toy, since it is an accessory for psychological and emotional relief.

How to make a spinner with your own hands

First, we will look at the main master classes, and later in the article we have prepared simple instructions for making a spinner without a bearing!

Making such a toy is quite simple, you just need to thoroughly study the design and details of the spinner:

a housing that includes a bearing and a plug;
petals, which also have bearings built into them;
additional plugs.

The most important part of the toy is the bearings; the efficiency of rotation, the number of revolutions and much more depend on them. The plugs are needed to hide the working mechanism of the bearing and to conveniently hold the spinner itself. The parts are very simple and can be easily made using available materials.

Manufacturing process

First, let's look at the model with bearings. For this we need:

cardboard
4 bearings
knife or scissors

First, we draw a drawing of the future model of your spinner.
We draw the sketch on cardboard and carefully cut out along the edges.
It is necessary to clearly identify and mark the places for the bearings; to do this, use a compass.
Each petal should be symmetrical to the other.
We cut out the holes for the moving elements with scissors and smooth them a little with sandpaper.
They need to be made in such a way that the bearing fits tightly into the hole.

Next, insert the bearings into the holes and generously fill the edges with glue. In this case, it is best to use construction adhesive, which is used for gluing various decorated parts.

It must be applied carefully so that nothing gets into the bearing.

There is one well-known method, which will be discussed further.

Wooden spinner

Making a wooden spinner is a more complex option, but it is also the most reliable. Using a jigsaw and a special construction tool, you can make a housing into which you insert bearings in the same way and secure them with glue. In each case, you can paint your spinner in a suitable color.

First we select the wood. It is best to use plywood as it is the easiest to process. The sketch of the body can be found on the Internet, after which we transfer it to the workpiece. Using a jigsaw we cut out the body.
Next you need to sand everything down.
Drilling holes for bearings
The thickness of the plywood must match the thickness of the bearing, otherwise nothing will work.

Spinner without bearings

Many people wonder how to make a spinner with their own hands without a bearing and at minimal cost. The most common option will be presented below. The easiest and fastest way to make a spinner is from plastic bottle caps. This is a very simple method that no one knows about (except you).

For this we need:

three bottle caps of the same size and weight;
drill bit;
ball pen;
glue.

Everything needs to be done in a certain sequence:

Glue the three lids together on the sides. It turns out to be something like a spinner without bearings.
Next, in the central cover we make a hole for the ballpoint pen. In this case, the diameter of the drill and the rod must be the same.
We cut off a few centimeters from the rod and insert it into the resulting hole.

In this easy way, you can make a spinner with your own hands, which can be rotated as much as you like without a bearing.

Making such a toy is very simple if you know or at least imagine how a spinner works. In any case, you can always replace the covers with any other parts of the same shape and size. Everything is very simple.

Harm from using this accessory

Having figured out how to make a spinner with your own hands without a bearing, you can talk about the negative consequences of using it. You must strictly follow safety precautions so as not to cause any harm to yourself.

A spinner made at a factory is completely safe, but the one you make yourself is not always so. It is necessary to carefully treat the surfaces, securely fasten the bearings and use it only for its intended purpose.

Do not give to children unattended!