Advantages of floors made from saw cuts
The saw-cut floor is made from natural materials.
Relatively cheap.
Very beautiful and pleasant to the touch.
Easy to do (relatively).
Flaws
Unfortunately, this type of flooring requires quite a lot of wood good quality, so it is recommended to cover only small areas.
Floors made from saw cuts need to be serviced approximately once every 2 years.
What will you need?
Round stones 10-12 cm thick, sawdust, limestone, clay, linseed oil, beeswax, water, lard.
Note: It is important that the cuts are very, very well dried (not to mention working, no moisture).
The process of making such a floor is relatively simple and very similar to laying paving slabs or paving stones. You need a hard, well-compacted surface, on top of which we pour a layer of river pebbles (about 6-10 cm). Then, using a rubber hammer, we begin laying the cuts. We tap and check with a level that the floor is level and that none of the cuts stick out or go too deep. As a rule, after laying, the distance from the surface of the cuts to the sand level is about 4-7 cm, and the distance between the cuts should be approximately 1-1.5 cm.
Mixture for filling joints
For a floor area of about 5 square meters In a 15-liter bucket, add 1 kg of lime, 5 kg of sawdust and 2 kg of clay with water to 1 kg of melted pork fat. After thorough mixing, you should get a paste-like mass. You can also add marble dust.
We introduce the mixture into the distances between the cuts and rub it well, as much as possible, without leaving air pockets. It should fill the gaps. It is very important that there are no voids left, otherwise cracks and water leakage cannot be avoided in the future. The remainder of this mixture can also be used to fill cracks in saw cuts (if applicable). After the last seam is covered, we leave our floor to dry for 1-2 days. If cracks appear, fill them.
After complete drying (another day or two), we polish the floor from the saw cuts well. It is even recommended to do curettage. You can rent a scraping machine to achieve the perfect effect. After this, check very carefully to see if there are any cracks.
And finally we polish beeswax and linseed oil.
p.s. And this is an ancient “pavement” made from saw cuts, which the craftsmen gave a hexagonal shape (shape honeycomb), she is more than a hundred years old. 
Please rate this post:
Wooden flooring is beautiful, comfortable, pleasant, practical option coverings. Below is step-by-step instruction How to make a floor from cut trees with your own hands. In the photo, saw cuts and .
Previously, we told you how to make it from wood cuts. The process is a little different, but in general, making a floor from wood cuts will not be difficult.
Let's get started?!
Step 1: Preparing the cuts
We saw tree trunks into equal thickness cuts. The width of the cut should be 5-10 cm, no less. Smaller cuts are too thin for the floor. All cuts must be made on both cut sides.
Step 2: Prepare the coating and lay out the cuts
Before laying out the cuts, it is necessary to clean the coating from dust and dirt. Next, we lay out the cuts on the surface. The best option The surface for laying wooden saw cuts will be concrete.
Place the cuts as close to each other as possible. Having laid out the floor completely, see if you are satisfied with the result or if something can be corrected. If everything is in order, move on to the next step.
Step 3: Glue the wood to the concrete
With the help of construction mounting adhesive, lift each cut, coat it with glue on the bottom and sides where the cuts touch, and put it back on the floor. And so on around the entire perimeter. Make sure that the cuts are strictly at the same level.
Let the glue dry completely according to the manufacturer's instructions.
Step 6: Apply Protective Coating
Treat each surface with polyurethane varnish and let it dry.
Step 7: Grout the Empty Space
To grout voids, use a mixture of tile grout and sawdust, at a concentration of 25% sawdust and 75% grout. +- 5%.
Step 8: level the surface
Check whether the surface is smooth after grouting. Correct any defects if found. The surface must be perfectly flat
Step 9: Apply Finish Coat
Apply 2-3 layers to the surface, with intermediate drying. Let the surface dry completely
Step 10: Invite neighbors to show off
We show our neighbors our exclusive solid wood floor and are proud of our work)
What is not made from wood cuts. Garden paths, shelves, table tops, interior decoration and much more. Using saw cuts instead of floors in a living room is what our author decided to do.
Materials and tools
dry logs of different diameters;
a circular saw;
grinder;
liquid Nails:
tile grout;
polyurethane varnish for wood;
From dry logs of different diameters to circular saw I sawed round pieces of approximately the same thickness.
Using a sanding machine, sand each cut.
I prepared the base of the floor by removing the old covering. Found myself underneath concrete screed, which made it easier for the author to carry out further work.
Next, he lays the cuts as closely as possible to each other.
Empty space is filled with smaller cuts and twigs.
Having laid out the entire area with liquid nails secures each cut to the floor.
After waiting for the glue to dry, the author grinder Levels and sands the floor. The floor must be level and smooth.
Use tile grout to fill the gaps between the cuts.
After waiting for the grout to dry completely, I covered the floor with polyurethane wood varnish. I applied the varnish so that it got into all the cracks. Polyurethane varnish Apply in 3-4 layers. After the varnish has dried, the floor from the wood cuts is completely ready.
There are many various types decorative floor coverings, but a DIY floor will be especially pleasing to the eye. Floors made from wood cuts look very beautiful and create durable coating. Not everyone can imagine what such a solution is, what its advantages are, and how to do it with their own hands.
Log cuts at the ends
Advantages of cut floors
All flooring materials, used by mankind, are made artificially, although they consist of natural raw materials. Solid parquet is produced using the technology of pressing and gluing lamellas. But if you pay attention to floors made of round timber, you can immediately say that such flooring is completely natural and natural. It will not cause harm to health, because the material is environmentally friendly. However, for the floors to last for a long time, you still have to cover them with synthetic protective equipment and varnishes.
Therefore, the above-mentioned advantage of naturalness also disappears. All that remains is to rely on other advantages that I would like to dwell on in more detail:
Installation of wood slices - like laying out a mosaic
- Mosaic. The floors look like they were made from a mosaic. Pieces of various sizes, textures and colors are used. Because decorative value of this material will give odds to many other species.
- Strength is determined by what kind of coating is under the stumps, how the elements are connected to each other and how they are protected. The type of wood also matters. It's no secret that oak slice much stronger than softwood.
This does not include the cheapness of the work, as many believe. Yes, you can get wood almost free and cut it thin layers, but to execute reliable connection parts, you will have to use a self-leveling floor made of epoxy or polyurethane. These products are not the cheapest, so you may even need more than three-dimensional floors. There are also a budget option– use of clay binder. But similar wooden surfaces do not have the strength that is required.
Attention! All the rumors about cheap flooring made from wood cuts are a misconception. The cost of finance and effort here is even greater than when arranging standard flooring.
Laying technology
All the talk about the pros and cons similar flooring will not lead to final decision. To understand whether it's worth it, you need to understand the technology.
Requires strong and stable discs to withstand furniture loads
You can take wood of almost any species, but there are two requirements for it:
- Strength. The flooring must withstand heavy loads. If we take into account conifers- fir, cedar, pine or linden with poplar, then they are considered soft species. The hardness and strength of wood is measured using the Brinell scale. So, according to this scale, wood must have a strength reading of at least average level in order to be used for parquet flooring.
- Stability. The material should not dry out or change its properties. linear dimensions, so the issue of wood stability also remains very important. Exotic tree species are immediately excluded from this criterion.
Oak has the two qualities described. Therefore, flooring made from oak cuts will become great solution. Regardless of the species chosen, it is important that the wood is dried. The use of wet material is unacceptable. There are two ways to arrange flooring from saw cuts. Let's look at each of them briefly.
Do-it-yourself floor made from wood cuts. Method 1
Sand base
Suitable for this technology end cuts round timber with a diameter of 10-12 cm. But using the same diameter is not necessary. Show off your richness inner world and imagination, beautifully using materials of various sizes.
In addition, you will need:
- clay;
- linseed oil;
- salo;
- water;
- wax;
- sawdust.
The material is laid like a mosaic, taking into account minimum distance between adjacent parts, so use in adjacent parts small elements it will come in handy. The surface of the base is covered with a 10 cm sand cushion. On top of the fine-grained sand there are saw cuts that are pressed into it. Along the way, you will need to check the horizontalness.
Adjacent voids are filled with a special solution, which can be prepared according to the following recipe:
- fat – 1 kg;
- sawdust – 5 kg;
- lime – 1 kg;
- wet clay – 2 kg.
All this is stirred until a homogeneous structure is achieved. It is recommended to add marble dust or glass fragments to the composition.
Fill all voids with the finished mixture and level the floor. After the solution dries after 2 days, the final finishing begins by scraping and polishing with oil or wax.
Floor made of wooden discs. Method 2
Installation with adhesive composition
There is another way to create decorative flooring from wooden cuts. Pre-cut elements of the same thickness are laid on the prepared plywood base and attach it to it with glue. The gaps between the elements are also filled with a special solution containing 20% sawdust.
After the solution has dried, begin sanding the surface, then the floor will become absolutely flat and smooth. Surface coating with sealant is the next step.
Attention! The bonding solution should not darken or change the texture of the wood, so you will have to experiment with the solution before using it.
Final finishing – self-leveling polyurethane composition or varnish coating. It is also possible to use epoxy-based compounds.
These are just the most common methods of arranging floors from saw cuts. But there are styling options on liquid concrete, which allows you to create solid foundation. Which method to use is up to each individual to decide.
To highlight the natural structure of the material, it is recommended to use stain. This will give the flooring a touch of expensive wood.
Usage wooden cuts is not limited to sexual structures. They are used to decorate tabletops, chairs and walls. Such extensive areas of application of saw cuts are explained by the decorative nature of the material, which can decorate any interior without the use of additional finishing.
Making floors from saw cuts and sections of wood with your own hands is not so difficult. At the same time, you will receive a unique interior that will become your pride. Note that you can use, in addition to round timber, also rectangular bars. To some extent decorative similar flooring there will be fewer, but there will be fewer gaps between them. Therefore, the bulk composition will be used more economically.
Floors are an important covering in any room, which can be created from different materials. Wood is considered environmentally friendly and attractive. Therefore, the floor is often formed with your own hands. It does not require the investment of numerous funds, and is also considered easy to create.
Features of this floor
A floor made from wood cuts with your own hands looks attractive and interesting in the photo. Its creation involves the use of special “rounds”, the thickness of which is several centimeters. They are formed as a result of cross-cutting logs.
Their correct placement on the base ensures the creation of a bright, beautiful and unique surface on the floor. To fix the coating, fill it with different liquid materials, polymers are most often used for this.
Pros of gender
It’s easy to create a floor from wood cuts with your own hands, but it has many advantages:
- an environmentally friendly coating is formed;
- it is possible to make a floor with minimal expenditure of money;
- you can use different unique opportunities for creating unique design, since it is allowed to use saw cuts from all kinds of logs, which may have different or similar fragments;
- elements differ in shape, color or size;
- such a solution is considered original for each house or apartment;
- It’s easy to make a floor from wood cuts with your own hands, which significantly reduces the cost of creating a covering;
- floors are considered universal, so they are suitable for any interior and style.
Some people even prefer to use cracked logs, which create a charming finish. But you should only use logs that show no signs of disease or rot.
Flaws
This floor has some disadvantages. It is important to select fragments that have the same thickness. If errors are made in technology, this will lead to the creation of floors that do not have high strength and durability.
What kind of logs can be used?
Not all elements are suitable for this process, as some requirements for them are taken into account:
- logs that are too soft are not used for the procedure;
- it is important to select cuts obtained as a result of processing hardwood;
- spruce, pine or aspen cuts are not suitable for these purposes, therefore optimal choice there will be walnut or oak;
- The financial capabilities of buyers are also taken into account, since natural wood it costs expensive.
If you use expensive types of wood, the structure will last a long time and look luxurious.
How to make a floor?
Creating a floor from wood cuts with your own hands step by step is simple and quick in time. To do this, follow the following steps:
- the procedure is carried out similarly to laying paving slabs, so initially you need to carefully prepare the base, which should be well compacted, even and solid;
- a layer of river pebbles is placed on top of it, and its thickness should vary from 6 to 10 cm;
- Next, the cuts are directly laid, for which they are adjusted using a rubber hammer;
- it is important to constantly check the correct positioning of each element by level, which will avoid distortions and other problems on the coating;
- between the cuts there remains a distance not exceeding 1.5 cm;
- then the seams between the elements are filled; the mixture for this can be purchased at finished form or make your own using clay, lard, lime and sawdust;
- often chosen polymer compositions of high quality;
- the mixture is introduced into the seams between the cuts, after which it is rubbed well, it is important to make sure that there are no air pockets, and if voids remain, they can cause cracks or water to penetrate under the floor;
- The procedure for filling the seams is repeated after two days.
Thus, according to the right technology It is very easy to create floors from sawn wood with your own hands, and this results in a high-quality and attractive design in any room.
What to do after creating the floor?
As soon as the floor is made from wood cuts with your own hands, you should polish it well. The best way to use this is scraping machine, and after sanding you need to check the coating for cracks. If they are missing, then at the end it is done hand grinding. After the floor has dried, polishing begins; for an environmentally friendly coating, it is better to use wax or linseed oil.
A floor made from saw cuts is considered interesting choice for any room. It has huge advantages, although it also has disadvantages. It is considered easy to create, therefore, through your own efforts and small financial investments, you can get an original and unique design on the floor.