According to the rules, after installation plastic windows The protective film must be removed within 10 days. This is due to the fact that the film in direct contact with the frame is very thin and delicate, and under the influence sun rays and high temperatures it is destroyed. As a result, we see the composition “tightly” stuck, and the longer it is not removed, the more it will dry out. Therefore, it is better to remove the protection in time.
How to remove film from plastic windows? What is needed to clean the surface and prevent the adhesive base from sticking even stronger? And what should you do if you couldn’t remove the protective film from the window in time? There are a number of ways to solve this problem.
How to remove solar control film from a window
If you decide to do everything that needs to be done in a timely manner, the film will be removed much easier. How to remove film from plastic windows without damaging the material? Use one of the following methods to solve the problem at home, without the help of specialists.
"Cosmofen"
This special solvent, which can be purchased from a company that installs plastic windows. There are 3 types of “Cosmofen”, differing in the degree of impact: No. 5, No. 10 and No. 20.
The strongest is No. 5, and if used carelessly, you can “dissolve” not only the adhesive base, but also the plastic itself. Therefore, it is better to use the least aggressive composition.
During operation, follow the instructions for use, and removing the protective film will not be difficult.
Knife, blade or scraper
When using sharp objects, be careful not to damage the surface. The edge of the protection is pryed off with a knife or blade, and the remaining part is removed by hand. Remember, the less you use cutting accessories, the less damage there will be to the plastic.
After you remove the film from a plastic window, noticeable traces of glue may remain on the surface. You can wash them using a hard bristled sponge and any foaming product.
Construction hair dryer
How to remove solar control film from a window using construction hair dryer? Follow the basic rule: when removing the protection, direct the air stream only to the frame, without touching the double-glazed windows. Otherwise, the glass may not withstand temperature changes and cracks will appear on it.
The mechanism of action is simple - under the influence of heat, the adhesive base softens, and its removal will not take much effort. You can use a steam generator or a regular hairdryer in the same way. The latter is effective only in cases where the film has not had time to dry much.
Solvent or white spirit
Before using one of these products, test its effect on an inconspicuous area of the surface. If the chemical does not harm the plastic, you can start working.
How to remove the protective film from plastic windows and clean the surface using solvent or white spirit? First, pry up the edge of the protection, and then apply the substance into the gap between it and the plastic. In this way, gradually clean the entire surface.
Paint remover RP6
You will need to apply the product to the surface in a thick layer and wait 7-10 minutes. During this time, you will notice that the remaining protection begins to “bubble”.
After this, put on gloves and glasses and remove the film from the plastic. Remains of the product and adhesive base can be washed with a concentrated soap solution.
Stiff brush and soap solution
This method is effective in cases where the window is located shadow side. The adhesive base does not have time to heat up very much, and its adhesion to the plastic is not so strong.
Prepare a solution of warm water and soap and remove any remaining protection using a stiff brush (not a metal one!).
Denatured alcohol
How to remove film from plastic windows with denatured alcohol? Pour the substance into a spray bottle and “irrigate” the surface evenly. After 3-5 minutes, pry the edge of the film with a knife and carefully remove it with your hands.
When working with chemicals, be sure to protect your hands with rubber gloves.
Detergent "Shumanit"
This chemical can be purchased at a hardware store. Clean plastic strictly following the instructions for use, as this substance is very strong.
After treatment, wash the area to be cleaned. clean water and wipe dry with a piece of soft cloth.
If, after removing the main part of the protection, small “islands” remain on the surface, take a regular eraser and clean the surface.
Why does the film dry out?
How to delete old film from plastic windows, if it has dried “tightly”? First you need to figure out why this happens.
How to remove old film from plastic windows if it has dried out
How to remove old solar control film from windows if it is stuck? You can use the following options:
- Contact specialists who have special tools at their disposal to solve the problem quickly.
- Use a special scraper designed for cleaning plastic and glass surfaces.
- Use a strong concentration of solvent, after testing it on an inconspicuous area of the plastic.
- Use dishwashing detergent and sharp knife. Moisten the surface with a soapy substance, and when it “soaks” a little, remove the protection with a knife.
- In some cases, chemicals used for cleaning can help remove the old protective film. kitchen stoves. The principle of action is the same as in the case of dish gel.
How to remove old film quickly and without much difficulty? Please note one caveat: sunny weather, when the windows warm up well, it will be easier to remove it. If you do not want to wait for suitable weather, warm up the window with a hairdryer before starting work.
Today there are several types of film, each of which is intended for reliable protection homes from the scorching rays of the sun. At correct use This material allows you to reduce the summer temperature in the rooms by five to ten degrees.
This protective agent has only one serious drawback - the difficulty of removing it from windows. Each film contains an adhesive substance with which it is fixed to the glass. And in many cases, when removed, it can leave visible marks on the window, which will negatively affect its appearance.
Sun protection film on the window
All existing species films are made from materials that reflect light, and many of them contain aluminum, which can also leave unsightly spots on glass. It is quite difficult to remove them without causing any harm to the glass surface. But if you use the series chemical substances designed to clean complex stains, you can try to remove traces of use protective film with minimal damage to glass.
All modern materials, which are designed to protect premises from excessive high temperature, contain aluminum and other substances that make them difficult to remove from surfaces. In order not to leave unsightly streaks and noticeable stains on the glass, remove such protective equipment should be approached as carefully and responsibly as possible. There are several most common ways to be careful, each of which can lead to success.
Steaming
If you peel the sun protection material from windows without preliminary preparation, then the likelihood of stains and noticeable traces from the adhesive is enormous.
The ideal way to prepare the film for removal is to use a modern steamer.
The procedure for cleaning windows from material using a steamer is carried out in several stages:
- A small area is heated using hot steam from a steamer. It is very important that the steam is directed to a specific place on the window.
- About five minutes after steam treatment, you should pick up a piece of film and gently pull it towards you, separating it from the window.
- The new section of the window is heated again until the material begins to move away from the glass.
The film area is heated using a steamer 
After five minutes it separates from the window
This is the most gentle and simple way to remove sun protection film. In this case, a minimal amount of marks remain on the window, which can be easily removed with a simple soap solution. This is just one of the simple answers to the question of how to remove film from window glass without visible marks.
Detergents and cleaning products
From others effective ways We can highlight the use of powerful ones designed for cleaning glass surfaces. They allow you to remove stains and traces of film from the window without special effort, but when using them, safety precautions must be observed, which consists of the following rules:
- When treating surfaces with chemicals, it is necessary to use the provided protective equipment. These include gloves, closed clothing and a respirator;
- compliance with the dosage specified by the manufacturer on the detergent container;
- compliance with the manufacturer's recommendations to avoid contact of the substance with certain materials that are sensitive to the components of the cleaning product.
Use protective equipment 
Study the dosage
You can clean windows using these effective means, How:
- Domax. This substance is intended for gentle care of glass ceramics and does not contain abrasive substances;
- Cosmofen;
- Schumann;
- Fenosol.
Schumanite is an effective remedy
However, even modern powerful preparations designed for cleaning surfaces cannot always cope with the consequences of the protective film material remaining on window glass. In this case, stains and other marks will have to be removed using a more rigid scraper, which is designed for cleaning glass ceramics. The remaining traces are then removed using a modern Fenosol cleaner. After this, the glass is washed first with a soap solution and then with warm, clean water.
All the methods described above, which tell you how to remove sun protection film from glass, are also suitable for cleaning wooden windows and for modern PVC and metal-plastic profiles. Compliance with safety precautions and the dosage of cleaning products will allow you to rid your windows of residues protective material without any particular harm to the glass and without harm to health.
Scraper for cleaning glass ceramics
other methods
There are other ways you can try to remove film from your window. One of them is to use a utility knife or other sharp object, such as scissors. During the procedure, you need to carefully pry the edge of the film with a knife to separate it from the glass, and then pull it towards you. It is recommended to roll up the already peeled off areas into a tube so that they do not stick to the window again.
You can also remove some types of film using newspapers and soapy water. The procedure is carried out in several stages:
- Regular newspapers are placed over the entire glass area.
- The newspapers are sprayed with soapy water until they begin to stick to the surface.
- Leave for an hour, regularly wetting the paper.
- Remove newspapers and film, which will come off much easier after the procedure.
Newspapers are placed on all glass 
They are sprayed with soapy water 
Leave for an hour, constantly moistening 
Easily remove newspapers and film
Precautions when removing film stains from glass
When carrying out work to clean windows from traces of solar control film, you should follow the recommended precautions. Some chemical cleaners may have negative impact on human skin and respiratory tract, and using sharp objects can cause injury. Therefore, when removing film stains, you must adhere to the following rules:
- carry out all work related to chemical cleaning substances only with strong, impermeable gloves;
- when wiping off marks, do not press hard on the glass, as this may damage its integrity;
- when working with sharp objects (knife, scissors, scraper), you should act as carefully as possible so as not to get hurt or damage the window;
- avoid getting hit chemicals on unprotected skin, eyes or respiratory tract;
- Keep materials and tools intended for removing marks from glass surfaces out of the reach of children.
Many users, faced with the problem of window film firmly “fused” to the PVC profile, rush to experiment, which does not always end well. Especially in the case of colored windows, there is a risk of destroying them. The OKNA MEDIA portal will tell you how to effectively and without disastrous consequences remove old protective film from plastic windows.
All plastic windows come to the market with frames protected by the manufacturer using self-adhesive film. According to the rules, the protective film must be removed as soon as possible after completing the window installation - especially when the PVC window is exposed to direct sunlight.
Why is it so difficult to remove old protective film from PVC windows?
Unfortunately, this happens quite often, and due to the negligence of installers or the user himself, the protective film on the PVC profile can remain even for several years. In this case, when they get around to putting the new plastic windows in order, the user will be in for an unpleasant surprise - it’s almost impossible to remove protective covering.
It is difficult to remove old window film from a plastic window profile because it consists of two layers. Outer layer ( transparencies) Under the influence ultraviolet rays starts to peel and is relatively easy to clean. But at the bottom there is a second layer of white plastic with markings applied - it is this that sticks so strongly to the substrate.
The presence of old film looks especially bad in the case of a tree-like profile, because usually a protective coating is used white. When exposed to UV rays, the film undergoes vulcanization and adheres very firmly to PVC surface window. At the same time, it becomes less durable and breaks easily.
|
|
Some try to wash away protective layer gasoline, acetone or other solvents - this helps a little, but at the same time you can remove the wood texture that is used to laminate the frame ( white PVC windows, of course, are insured against this). Experts do not recommend exposing the surface of colored PVC profile too much mechanical stress (scraping or sanding), because it is very easy to damage the lamination layer.
Eureka: There is a way to get rid of old protective film!
Fortunately, there are several ways to get rid of the protective film, we suggest you consider one of them. This method is simple, effective and, most importantly, will not destroy the plastic window. However, the procedure will take quite a long time and will require the use of a device with a steam cleaning function.
Such a device can be bought without problems; they are often sold in supermarkets. Please note that the package includes a special hose that allows you to fix the nozzle. Versions of this device often appear on sale, in which steam exits directly from the tank through a nozzle. In this case, you will have to constantly hold the heater in your hands during cleaning, but it will soon become clear that heating the film in the lower part of the frame is impossible in this case (the window sill gets in the way).
Work begins by filling the purifier with water and connecting to the power supply. After a few minutes you can start heating small area protective film with a jet of steam (hold the nozzle directly above the film or even touch it). Heat a small section of 1-2 cm across the entire width. If the window film is too old to peel off, you will have to reheat it (after cooling). At this time, you can heat the protective coating of the window from the other end.
To remove the protective film using steam, shortly after heating a small area, you should try to separate the film from the substrate with your fingernail. This must be done carefully and slowly, across the entire width of the tape. This is the most important point. It is necessary to ensure that a small piece of the film peels off across its entire width. Then you can grab the end and slowly (!) tear off the film while simultaneously heating with steam from above and below (at the points of contact with the substrate).
If the protective film begins to tear and its fragment does not come off, you need to use a fingernail in this place and lead to a situation where it peels off again across its entire width. After removing a sufficiently long fragment, cut it off with scissors, leaving 2-3 cm so that there is something to cling to to continue further cleaning of the PVC profile.
After removing the protective layer on the surface window frame remains white coating, which is quite difficult to wash off. And here there is a proven method - you can use a glass cleaner for this purpose (for example, Mister Muscle).
When buying new plastic windows, do not ignore the advice of the window company, which is clearly stated in the operating instructions, when it is worth removing the protective film from the PVC profile. This will allow you to save time and money, and save your nerves. In general, following the manufacturer’s recommendations not only in this point, but also in all others, is the key to the impeccable appearance and durability of your plastic windows.
——————————————————————————————————
Good afternoon.
I am asking for advice on the issue stated in the title.
What do I know?
1) Remove immediately. After installation it’s easy and simple.
2) Pour boiling water.
3) Heat with a hairdryer and rub with a plastic spatula or kitchen sponge made of wire or fishing line.
4) Lift it up a little with a plastic “something sharp” and spray it with WD-40, then see above.
5) Cleaners Cosmofen 5, 10, 20. Then again see point 3.
For these 1...5 points = any comments, advice and experience.
I will also be grateful for a different EXPERIENCE...!
P.S.
The problem is relevant.
I'm asking everywhere now.
It turned out to be not so simple...
I don’t know the composition of this film, but at one time, while installing my mother-in-law’s greenhouse, I did not remove the white protective film from some sections of the polycarbonate sheets. I left it specifically to shade some areas of the greenhouse. Three years later I wanted to take it off - it’s just figurines. Dried in frost and sun. Neither heat nor solvents helped. It has completely lost its elasticity and cannot be removed with film. And picking out pieces of a couple of millimeters is ineffective.
By the way, you can’t give a damn and paint the top with paint. Because gradually the film still peels off in small pieces.
———————————————————————————————————————
The problem is that this is the gate of my main employer; I hired the gate installers for him.
And the fact is that neither the gate installers nor the Uzbek guards ( they most likely did not read the inscription on the film “remove immediately”) did not remove the film immediately or earlier,
It will be my fault anyway. It’s okay, but “fiiii...” will be said to me...
P.S.
I don't blame the Uzbeks.
And for the lazy installers, I wish you “0” orders in the New Year.
P.S. No. 2
By the way, after buying an apartment in a new building, I did not remove the film from the outside frames.
8 years have passed and it almost fell off on its own. If you rub it with your palm, everything immediately crumbles.
But the “boss” won’t wait 8 years, IMHO.
When I bought the Opel, a pre-sale protective striped film was pasted on the driver's threshold. I didn’t take off the couple for six months, it dried up and came off in pieces. Cleaned it with a solvent (like white spirit)
————————————————————————————————————————-
I was tearing off the remains of worn out advertising from the sides of my truck: Spatula and warm water with fairy..
All other methods did not help... Namely: hot air gun, sunflower oil, solvents...
The film stuck tightly for 7 years... The area is huge... Destroyed in two evenings...
—————————————————————————————————————————
So far I only read about failures:
This is a general problem - all kinds of protective films on windows, roller shutters, and gates must be removed by installers upon completion of installation. Next, so as not to get dirty installed structures, customer on our own must protect them (for example, polyethylene and masking tape). If you leave the original protective films, they will inevitably stick to death. Not shot films- a sign of either poor qualifications of the installer, or his indifference to everything that happens. For example, I insist on removing films after installation, even when the Customer asks to leave them.
How much in the Kyiv region? costs sectional doors with burnt film - it’s impossible to count... and how many bright green windows... in general, dear customers - don’t be lazy, force workers to remove the original films and cover everything with masking tape - it’s cheaper than then tearing off the results with tweezers for weeks...
———————————————————————————————————————
Thank you.
Yes…
I also read all this sad and hopeless stuff.
“Said” has a week to create a miracle with a small heat gun instead of a hair dryer. If he can’t, I’ll come to him next Thursday with VeDeshka and a kitchen wire sponge.
—————————————————————————————————————————
here's a hard washcloth with Fairy or oil or white spirit - it might work. The paint on the iron roller gates does not seem to be the most delicate. You can also rub it lightly.
not more than a month ago I took it off.. from just such a gate.. dorkhan, or whatever is correct.. I cut it along the top and bottom stationery knife on the edge metal corner.. was removed in large pieces.. the gate stood for 5 years..
I peeled off a 3*2m gate for about thirty minutes..no big deal..
——————————————————————————————————————————
lucky. Willy obviously can’t do this...
——————————————————————————————————————————
I removed it with a Karcher cutter and it flew off for my dear soul.
——————————————————————————————————————————-
Ahead) Plus to Karcher.
Too Willie. Myself and a friend sometimes work around the gates, I’ve already installed a lot of them, removing the film is at the customer’s request, but for free. Many people install gates, but there is no finishing yet, so the installers don’t peel off the film. We always warn our clients not to delay removing the film.
——————————————————————————————————————————
The most important thing is that it’s not so dreary, everything is like entertainment, you just need to pay a little attention to where to point the cutter. The best remedy.
——————————————————————————————————————————
Guys, thank you very much. For the mud cutter...
We have a Karcher. I won’t be too insolent if I ask you to recommend the TYPE or ARTICLE of a cutter - there are a lot of them in the Karcher catalogue...
MORE HELPFUL...!!!
P.S.
Although other acquaintances were already skeptical and predicted that I would suffer with the cutter.
They say they were all wet, but to no avail.
On the sunny side it gets really hot.
Ours is sunny. One summer has passed.
Plastic windows are often equipped with various films that are needed to protect from the sun, give the glass greater strength, and decoration. When purchasing an apartment, the windows can be covered with such films, but the new owner does not always need them. In addition, if the time has come to update the windows, since films tend to become unusable, the question arises of how to remove the solar control film from the window.
Coating removal methods
You can remove the sun protection film from the glass different ways, choosing the most convenient and affordable. This is done both mechanically and with the help of various detergents; they also use a combined approach in order to clean efficiently.
The film can be quite useful: it has a small thickness, but at the same time it makes the window much stronger; it can no longer be broken with a simple stone. Exist different types films that help protect the glass unit even from strong impacts, such as a shot; They are classified as protective. It will not be possible to remove perforated film from glass or any other type of protective or tinting from the outside: an attacker will not do this, since the process requires a lot of time, effort, and attracts the attention of others. Most films are applied with inside, with the exception of protective.
Knowing how to remove film from window glass may be necessary if you want to replace it when updating the interior or replacing a double-glazed window. Sometimes a product loses its visual appeal and requires updating, or the owners of the room want to change its lighting, make the room lighter or darker. The process of removing film is simple and does not require hiring a specialist, but it is worth considering that you will have to spend a sufficient amount of time and effort on this. You need to work carefully: in the process it is easy to damage the glass and scratch it, especially if you remove the film using hard materials like a spatula or a rough brush.
What should you do when you need to remove film from a window?
When choosing a method, means, or option for cleaning glass, room owners take into account several parameters:
- You must not harm the glass.
- Spend as little time as possible on this.
- The option should be inexpensive.
- There should be no traces of glue, film residues, or various contaminants left on the glass.
The easiest way to remove the sun-protective film from glass is to use a spatula and your fingers. Some types can be carefully pryed off by grabbing the edge and tearing it off, but this does not always happen due to the fact that the film is glued unevenly, is damaged in places and peels off.
It is quite difficult to remove film adhesive from glass. It is difficult to remove with detergents and is not susceptible to mechanical action. In order to remove it, you can use white spirit or another alcohol-containing substance that can gently clean the surface. You should not use rags with coarse pile, as this may leave marks on the glass that are visible in the sun.
Understand , how to remove old film from plastic windows, it may be necessary if it is damaged or you want to change it appearance windows, renew the old coating, which has already deteriorated.
What methods for dismantling are there?
Removal methods can be divided into two – mechanical and chemical. The first allows you to remove film from plastic windows without spending much money, but with the risk of scratching the glass. The second will take longer and cost more, but with the right products you can thoroughly clean the surface without causing harm to it. For greater effectiveness, it is best to combine the methods: first, you will need to tear off all swollen, cracked or otherwise deteriorated film.
You can remove the film from plastic windows by hand, then get rid of the glue using substances such as COSMOFEN 10, FENOSOL. These detergents have more cheap analogue, which you can buy at a hardware store: it's called P-12.
It will be much easier to remove the protective film from plastic windows if you heat it up with a hair dryer before tearing it off. Heated glue becomes more viscous and allows parts of the structure to be peeled off. However, it is better to remove the glue itself when it has cooled a little.
You should try to heat the surface evenly: the better you do this, the easier it will be to remove the self-adhesive film from the glass and the remnants of its glue. The latter will not be easy to remove; you will need to use a solvent, a scraper and detergents. You need to act carefully, otherwise you may scratch the glass. A steam generator can help in this matter. You can use it to remove stained glass film from glass. ,
get rid of tinting or protective film, glue residues. If you don't have a steam generator at hand or powerful hair dryer, do not try to heat it up with an iron. This way, the film will not be removed, but it will partially stick to the surface of the iron, which can significantly damage it, and after cooling it will not be easy to tear it off from the iron.
You can remove the self-adhesive film from the glass, if it is warmed up well, using a hard eraser for artists. Eraser residue can be easily removed from the window. To do this you need a dry sponge or rag. If there is any glue left, you can reapply the eraser or use a solvent. Most hardware stores will have something to remove film from glass.
Before removing film from glass, you need to carefully study all the methods, purchase suitable detergents and tools with which you can clean the surface.