The easiest way to transfer any image to fabric or wood. An easy way to transfer an image to wood Transfer an image to wood with an iron

I want to add a couple of nuances when using colorful magazines. Apparently, temperature plays a role here first rather than pressure. therefore, using denser pages increases the warm-up time. but the temperature is more uniform and the heated area lasts longer. more thin sheets there are several disadvantages. 1 this laser printer jams thin paper SOLUTION to pass a sheet of regular 80 paper together with a thin sheet
2. thin paper warms up faster and therefore, in addition to your stencil, a magazine drawing can also stick to the workpiece. SOLUTION It is necessary to control the transfer of the stencil without overheating the sheet too much or simply neglecting it if the drawing does end up on the workpiece. In principle, it does not interfere in my case because I use it for cutting. and then followed by sanding with sandpaper. If, however, the cleanliness of the stencil is still necessary, then experimentally select the temperature of the iron. Because the toner adhesion temperature is lower than the paint peeling temperature.

Here is an example of overheating.

Here is an example of a more precisely adjusted temperature


here is the media sheet from the top second photo. you can see how almost 100% of the stencil design has peeled off, but the magazine design has not been damaged

The work shown in the example was done for a person who is interested in aviation, so the photo for processing was chosen to correspond to his favorite topic. You should choose a photograph that is suitable in its content and mood for the person for whom this work is being prepared. Above is a before and after image.

Step 1. Materials needed for work

Below is a list of all those necessary materials that were used. It is not necessary that you will need this entire list in your specific job. You can get creative and replace some materials with others.
Here's what it took to create this work:

• Printed photograph;
• Wooden plates, same size as photo;
• Gel Medium (gel based on acrylic paint);
• Brush for applying gel to a wooden board;
• Spatula or knife to evenly distribute the image;
• Wood paint and fabric (optional);
• Pigment;
• Sandpaper;
• Wax for smoothing and compacting the applied photograph;
• Wax brush;
• Hanging bracket;
• Brackets for fastening (since two planks were used).

Step 2. Image search and processing

At the first stage of creating a picture, you have to find, process in a graphics editor and print a photograph. Please note that the example used a color photograph, good quality, and the result was a monochrome painting made in an antique style. To ensure that your photo does not come out too noisy when printed, the original image must be of high resolution. We create monochrome and the effect of an old photo using a graphic editor, such as Photoshop. At this stage, you completely form your future picture. How you make it now will determine how it will look when finished.

Step 3: Print the Photo and Find the Wood Plate

Having prepared and processed the image, you need to print it. Decide on the size. The example shows a work of 20x30 cm, that is, A4 format, and perhaps this is the most best option both in price and in size, to do more will cost more and take longer, to do less will result in the work being too small.
Finding the right wooden plaque is a little more difficult than printing a photo. It is quite possible that you will have to go to several hardware stores to do this. There is a more expensive one, but convenient option– you can make a plate of the desired size and format to order. But again, this option may cost you a lot more. You can also take two plates and combine them together, as shown in the example.

Step 4: Apply gel to wood plate

Let's get straight to work. Applying gel to wood is the most crucial moment in creating a picture; the final result depends on how well you do it.
Carefully apply a small layer of gel to the entire surface of the board. If you apply a layer that is too thick, the picture will look unsightly; if you apply a layer that is too thin, it simply won’t adhere and will sag in some places. Try to make the layer as even as possible over the entire surface. Once the gel is applied to the board, it's time to transfer the image. I must say, this is as complex and meticulous a process as applying protective film on your phone screen, it requires enormous concentration and nerves of steel from you. Air bubbles will appear during application in any case, so try to smooth the picture as much as possible and eliminate bubbles. You can smooth it with a spatula, but very carefully so as not to scratch the photo. Also, for this purpose you can take a ruler or fabric; this option is less “traumatic” for the image.
After you have transferred the image to the plate and got rid of any air bubbles, leave the painting overnight and make sure that no one touches it until the next day.

Step 5: Remove paper from wood

Now you need to get rid of the paper in the painting, so that only the ink from the print remains on the board. To do this, take a cloth and moisten it with ordinary water, then pass the damp cloth over all surfaces of the painting. This is a pretty messy process, so it's best to do it in old clothes just in case. In different places, paper can be removed in different ways, somewhere easier, somewhere more difficult, so it is very possible that you will be tired by the end of the work. Also, be prepared for the fact that you will not be able to remove all the paper at one time, and the process will have to be repeated several more times, with an interval of 20-30 minutes. And another small recommendation - keep a vacuum cleaner handy, because there will be quite a lot of dirt.

Step 6. Finish transferring the image

And now the most creative moment of the whole process begins. It is in your hands to make the picture the way you want it to be, to do this, turn on your imagination and get ready to work. In our example, the goal was to make the picture aged, so that it would look like a rare thing. If you want to get the same effect, look through a number of old photographs, images from the early 20th century, analyze them and start designing them.
First, apply a stain of paint to the wood and blot it with a cloth to remove excess, being careful not to overdo it. When the paint dries, rub it a little with the same rag for a more antique effect.

Now we sand the edges, get rid of excess gel and continue to give the painting an antique effect. Now we apply pigment along the edges. Using the applied pigment, you can create something like a vignetting effect, or you can add pigment only on opposite edges to create a kind of frame. To apply the pigment, you can use a regular sponge or porous cloth. The pigment package is smaller in volume than the paint package, so use it sparingly so that you don’t end up without pigment at the most crucial moment.

When additional effects using paint and pigment have been applied, we proceed to the last stage of work in this part. Apply wax to the finished image to give a glossy effect. Use a medium brush to apply a thin, even layer to the print. Just like paint, the wax must dry thoroughly. When the wax dries, go over it with a cloth to smooth the surface and remove excess. In the example we used soft wax, so the resulting surface is not too shiny, but the surface looks smooth and beautiful.

Step 7. Hang the picture

When the work is done, the painting is presented, help the owner hang your masterpiece on the most appropriate place. If, as in the example, you used two boards folded together instead of one solid one, then you should first combine them together with two small mounting brackets, which can be purchased at any hardware store.

Then, attach two mounting brackets to the upper corners so that the painting can be hung on the wall. When attaching the brackets to the picture, make sure that the length of the screws is less than the thickness of the wooden plate. I wouldn’t really want to ruin all the work done because some little detail was not taken into account.
For a picture more small size You can attach a small board at the back, just like they do on frames. You don’t need to hang such a picture on the wall, but simply put it on a shelf.

It’s nice to turn ordinary things “like everyone else’s,” with a little effort, into your own, cozy, personalized ones. Good way– decorate them with an original design. And even if you consistently skipped art classes at school, and even draw a little worse than a fifth grader, it doesn’t matter. This simple method will allow you to decorate all the textiles and wooden surfaces in the house with funny designs. And please your friends with original gifts.

Authors of a resource popular among designers shutterstock offer to try simple technology home printing. It is available to every owner laser printer. Or someone who is not too lazy to go to the nearest copy center and print out the desired design. This method will allow you to easily transfer the image onto fabric or wooden surface.

You will need:
Acetone (or a nail polish remover based on it);
Cotton pads;
Plastic card;
Scotch;
Ruler;
T-shirt/fabric/wooden surface on which the design will be transferred;
Desired image.

Step 1: print the picture on laser printer in a mirror version. An inkjet printer is a bad helper in this matter, because... does not guarantee even distribution of ink, which will be reflected in the final result. The darker the original image, the better.

Step 2: put the sheet down face down onto a fabric or wooden surface. It is advisable to secure it on one side with tape so that the picture does not “run away”. Soak a cotton pad or brush in acetone and carefully wipe the back of the design until the paper becomes wet.

Step 3: take plastic card and using it like a scraper, go over the entire back side drawing. It's like you're rubbing it in. First from bottom to top, then from top to bottom, repeat several times. Do not press the “scraper” too hard so as not to tear the print. The main rule is that all this time paper with an image should be damp with acetone. This will help the design adhere to the fabric or wood.

Step 4: Gently pull back the edge of the sheet with the image and evaluate how the “imprinting” process is progressing. When the drawing is completely transferred, remove the paper.

Probably, in every house where attention is paid to the interior, there are paintings or their modern analogue - photographs. Even most offices and offices have works of art. Most often, these are amateur works that depict a landscape, and such design of the room will not surprise anyone. Today I want to invite you to consider interesting works artist, thanks to whom you can add a fresh touch to your interior.

Thanks to today's master class, you will learn how to transfer an image from a photograph to a board. The author offers us urban scenes from the beginning of the last century, but you can use this method of image transfer for any photographs.

Such works look great among modern surroundings.

For work we will need:
- board;
- photo;
- laser printer;
- fine sandpaper;
- PVA glue;
- acrylic lacquer;
- sponge;
- warm water;
- acrylic paint.

The photo below shows a step-by-step and accessible way for everyone to transfer any image onto a wooden surface.
1. Enlarge the selected photo to the desired size, and then print it on a laser printer so that the reverse image is obtained.
2. Sand the board on which the image will be with fine sandpaper or, if possible, sand it with a machine (the surface of the board should be smooth).
3. Cover the surface of the board with PVA glue (using it gives the most good result) or acrylic varnish.
4. Carefully place our printout with the image down, smooth the surface with a sponge, expelling air bubbles and trying not to make folds (the procedure is similar to gluing wallpaper).
5. Leave the image to dry (it will take about 12 hours).
6. Using warm water and a sponge, carefully remove the paper from the board. If the paper cannot be removed with a sponge, you can roll it up with your fingers - the design will not be damaged. We remove absolutely all paper from the image.
7. When the image is dry from moisture, cover it with acrylic varnish.
8. Wait for the varnish to dry.
9. The image can be left as it is, or it can be aged using acrylic paint. You can stamp the image different colors- in this case, one color is superimposed on another. To prevent colors from mixing, intermediate drying is necessary. The protruding parts of the image are carefully processed with fine sandpaper.

As you can see, this method of transferring an image onto a wooden surface is simple and accessible to anyone who wants to create a unique and original work of art. Thanks to imagination and the use of acrylic paints, you can create not only a series of urban scenes and portraits in a retro style, but also interesting still lifes. Such an image can be not only a wonderful decoration for your home, but also an extraordinary gift to friends and relatives on the occasion of a special event. Try it, you will definitely succeed!

In the variety of materials used for finishing, wood occupies a special place. This material is notable for its unique texture, environmental friendliness and natural origin. The wood itself, especially when varnished or otherwise decorated, is quite beautiful. However, at the same time, it often becomes the basis for placing certain images. Moreover, the latter can be transferred independently. And there are several ways to do this.

Unlike paper and canvas, painting on wood is something new and interesting in our design. Therefore, such paintings will attract attention, and those people who want to create an interior that can surprise can consider this particular option.

In addition, you can decorate the wood that is used directly in the decoration, making the interior that is familiar to many look completely new. In addition, this way you can decorate a variety of wooden crafts, starting from boxes and ending with furniture.

Finally, transferring an image onto a wooden surface can be a hobby for children and adults, and for some, a way to earn money. After all, things self made are actively being acquired today.

What needs to be done with the drawing and wood before transferring

• Transferring an image onto a wood surface, like any other, is in some cases impossible without the mirroring effect. In the case of an image, this is not so important, but it is better to initially make letters and numbers mirrored, so that after transfer they will take on correct view;
• Any drawing is best transferred in high resolution. During the work process, blurriness may appear, and if the image resolution was initially low, this can greatly deteriorate the quality of the final result;
• The quality of the transfer directly depends on how clean and smooth the surface is. Any contamination is unacceptable, as are unevenness. In the latter case, you can use sandpaper;
• The color of the wood can also play a role in transfer. It is best to use options that are as light as possible.

Transfer with sublimation paper

A special type of paper that, when heated, can adhere to a surface, such as wood. Anything can be printed on such paper, and the process of transferring an image with its help is as simple as possible.

Ironing paper

It is often used when it is necessary to transfer images to wood for subsequent tracing with a special soldering iron and thus creating a picture. Some people draw by hand, but others prefer similar method. However, the method is also suitable for creating final products, and due to its cheapness and simplicity, it is very accessible and popular.

To transfer, you need to print the desired image on a sheet of paper. The sheet itself is laid on a perfectly cleaned and smooth wood surface. In this case, the paper is moistened with a small amount of acetone, which will make the process of transferring pigment from it to wood when heated better.

Important! When working with acetone, all precautions should be taken. Remember that the material has strong smell and actively evaporates. It is best to work in a ventilated area, and you should protect your respiratory system with a respirator or at least a mask. It is also important to have a fire extinguisher on hand to prevent static electricity.

By stretching the paper soaked in acetone until required sizes, we begin to iron it with a hot iron, and after a while the image will be transferred.

Transfer using decoupage film

Decoupage is becoming a very popular hobby, so many people know how to handle film from it. Having printed the required image on it, also prepare acrylic paint white.

It is necessary to perfectly clean the wood and also give it a smooth surface. Next, we apply pre-slightly diluted paint in two layers. Moreover, the application directions must be perpendicular to each other.

The paint must be allowed to dry. After this has happened, dampened decoupage paper (about 30 seconds soaking in water room temperature) are placed on the surface, removing the base and rubbing with a sponge to ensure a tight fit. After waiting for it to dry, you can treat the surface with varnish.

Transfer using PVA or gel medium

Regardless of the material chosen, the process is approximately the same. However, in the case of gel, the application occurs directly on the board, well, the glue is applied to the photograph. The photo itself can be a simple printout on plain paper. If this is important to the image, it is necessary to have a mirrored version of the photo, as later the picture will take on the correct appearance. The following is the procedure:

• The wood must be thoroughly cleaned and perfectly sanded to create a smooth surface. Can be used sandpaper with grit 120;
• Processing photos with glue or wood gel. In the case of the latter, it is necessary to do everything as carefully as possible, without missing the slightest fragment;
• The sheet must be glued to the lubricated surface, and then passed over it with a roller for a better fit, absence of folds and air bubbles. This stage is extremely important, since it determines how well the drawing will be translated;
• Leave the product overnight, then, as soon as the gel is completely dry, wet the sheet and remove it with a dishwashing sponge. The image is translated quite reliably, and it is not so easy to erase it. However, it is still better not to try too hard. However, in the case of PVA glue, it will be more difficult to erase the paper layer;
• Once all the paper has been removed, make sure that there are no traces of paper left on the surface, as they may interfere with the next stage– varnish coating. You can use waterproof or clear acrylic varnish.

Return