A “dry drain” is a siphon for drains in shower rooms and other rooms where water is used. Serves to prevent sewer gases from entering the room.
Unlike a conventional siphon with a water lock, a dry drain can perform its functions during long breaks in the use of water.
That is, even in the toilet, after a couple of months of non-use, the water evaporates and air from the sewer begins to flow into the apartment. Which of course is bad. We have the same thing with other siphons with a water seal.
What can be done with the toilet and siphons during a long absence - read here.
The dry drain is designed in such a way that sewer gases are cut off not by a water lock, but by plastic or metal curtains.
There are also dry ladders with a float. In the absence of water, the float sits on the seat and blocks the air supply. But this option is not very good -
if there is excess pressure in the sewer (and this sometimes happens), the gas will be able to lift the float and penetrate into the room.
Water discharge from ladders can be vertical or horizontal. Horizontal ones are more often used. In this case, it is necessary to ensure sufficient deflection sewer pipe, starting from the ladder itself.
Let me remind you of the SNiP requirements for pipes diameter 50 mm - pipe slope 3cm/1m. When laying pipes, we try to avoid straight, and even more so sharp, corners.
If the drain is installed in the floor, then it is very important Right make a slope of the floor towards the ladder. How to do this is described here.
Stanislav Plitochkin was with you. Let me help you save SVDN©!
2 comments
Good day, Lucia Mikhailovna! The best thing I can advise you is to take a photo of the ladder on your phone and show it to the seller at the construction market. Most likely you will be offered to buy the entire ladder, because I have never heard of them being sold in parts.
If three or four sellers tell you so, then you have no other choice - you’ll have to buy. But there is a chance for a positive outcome, so try it!
Good afternoon, Stanislav! Help me please! I have a steel drain installed in my shower. But the grate and something that should block gases from the sewer are missing. I can’t decide which component I should buy, what is the name of this component? Or do I need to change the whole thing and buy it assembled? Could you advise me via WhatsApp? My number is 89256260038. Sincerely, Lyutsia Mikhailovna, pensioner.
Add to bookmarks
Dry shutter – best protection from the penetration of unpleasant odors from the sewer
One of the most popular devices in drainage systems is the sewer drain ladder. They are intended for receiving and discharging wastewater from a horizontal floor surface into the sewer system. These devices are widely used in residential, public and industrial buildings. The design of the ladder must provide the following functions:
- drain water quickly and efficiently;
- filter wastewater from large contaminants;
- prevent the penetration of unpleasant odors into the room.
Advantages and scope of dry drain
Until recently, only ladders with a hydraulic seal were produced. A water seal is a specially filled water seal that prevents unpleasant odors from the sewage system from entering the room. Such a seal requires periodic updating in the form of a spill of water. The most common problem when operating sewer drains with a hydraulic seal is the drying out of water and the unpleasant odors that the sewer system is rich in easily penetrate into the room, causing inconvenience to people.
Assembly diagram for ladders with straight and oblique outlets
Let's figure out what can cause the water seal to dry out. There are many reasons, and the most important among them are: the drain is used sporadically (for example, it is placed in a guest bathroom, in a shower room of a hotel complex, or is intended to drain water in case of an emergency leak, and not for regular everyday use), heated floors, increased air temperature indoors, hot climate, failure of the water seal due to errors in the design of the sewerage system.
Currently, requirements are becoming more stringent; people need comfortable use of devices, eliminating additional labor costs for servicing devices.
The way out of this situation is to use a ladder equipped with a dry seal, and this solution is becoming increasingly popular.
This device does not allow the appearance of an unpleasant odor in the absence of a water seal and does not require frequent maintenance. A dry seal for sewerage can work either independently or in conjunction with a water seal, when each of them complements each other.
Dry shutter device
The most common devices:
- Membrane. Under the pressure of water passing through the drain, the valve opens, and after the water passes, the spring moves the membrane to its original position. Access to unpleasant odors is reliably blocked.
- Float It works due to the fact that the float is always on the surface of the water seal, and when the water evaporates, the float ends up at the very bottom and closes the passage.
- Pendulum. Under the influence of gravity mechanical device constantly strives to take a position blocking the sewer pipe.
- Based on the molecular memory properties of the material. Tubes made of elastic material are used, which always tends to return to its original shape.
Dry and combined drains are made from durable materials(mostly plastic body and grille made of of stainless steel) on modern equipment. The lineup these devices expand, you can choose a dry ladder equipped check valve to protect against the entry of wastewater from sewer system in case of flooding, and also select models that can be used in unheated rooms under conditions subzero temperatures, as well as heavy-duty, able to remain sealed under significant impact loads.
Main technical parameters
When choosing any sewer drain, including those with a dry seal, you must pay attention to a number of the following important technical points: direction of the outlet and its diameter, throughput and its height. The outlet of the ladders is either located horizontally (straight and oblique outlets are made) or vertically (pointed down). Next parameter, which must be taken into account is the diameter of the outlet. There are ladders with 50 and 100 mm. In residential construction, drains with a nominal bore of 50 mm are mainly used; they must ensure the removal of wastewater in an amount of at least 0.7 l/s. Drains with a nominal opening of 100 mm are installed in public premises and industrial facilities; they must ensure the removal of wastewater of more than 2.1 l/s. When selecting a sewer drain, great attention should be paid to such a parameter as the height of the drain (in modern models height ranges from 7 to 18 cm). Ladder made from quality materials, has an almost unlimited service life.
Installation of a sewer drain
Installing a dry device is no different from installing a drain with a water seal. It must be remembered that from quality installation, correct connection to the sewer system and its service life, safety of water leakage and aesthetic appearance after finishing. Installation of a drain entails some lifting of the floor in the shower room or other room in which it is necessary to drain waste water from a horizontal floor surface. It is extremely important to create a slope of the floor to direct water towards the drain.
The floor in the room in which the sewer drain is installed must be a system consisting of several layers:
- material that provides thermal and sound insulation (for example, polystyrene foam);
- concrete screed;
- membrane material with waterproofing properties;
- a concrete screed that sets the required slope towards the ladder;
- ceramic floor tiles with a rough surface and a minimum percentage of water absorption, which is laid on a special adhesive solution.
When implementing installation work When connecting to the sewer, you must remember that the drain grate is installed flush with the floor surface and should not protrude above the tiles located in the immediate vicinity. The tiles are laid starting from the ladder. The thickness of the joints between the tiles should not exceed 2 mm; when sealing the joints, water-resistant grout is used. After completion of the work, the ladder is securely concreted into the floor.
Opt for a dry sewer drain and you will be able to forget about the musty smell from the sewer, and you will not need to regularly replenish the water seal with water. This device will serve you long years, perform their functions reliably and delight with ease of maintenance.
The drain HL 310 NPr is used in interior spaces for drainage of wastewater from the floor level. The drain is equipped with a 50 mm water seal (Primus “dry” siphon), which does not allow sewer smells into the room when it dries out. Permissible load on the ladder - maximum 300 kg. Throughput - 0.5 l/s. Drain temperature - no more than 85°C (short-term drainage of water with a temperature of up to 100°C is possible, but for the drain volume - 100-200 liters). Outlet - vertical DN 50/ 75/ 110. Weight of the ladder HL 310 NPr - 0.7 kg.
The 310NPr drain has: a polypropylene extension with a 123x123 mm subframe, into which a 115x115 mm stainless steel grid, “dry siphon,” is inserted. The body is made of polyethylene with a “plate” for catching waterproofing.
The price of the ladder HL 310 NPr is 2237 rubles.
Installation features of the HL 310NPr drain: The height of the extension element of the drain is adjustable from 12 to 70 mm (it is cut to the height of the screed). You cannot cut the body! Because this will result in reduced throughput. If it is necessary to increase the height of the ladder, HL extensions (340 N and 85 N) are used. If the drain is installed in a gap in the waterproofing, then the rubber sealing ring is not placed on the extension element. The absence of a ring allows water that gets on the waterproofing to flow freely into the sewer through special channels in the extension element and the drain body. If used as waterproofing sheet material type - bitumen sheet, EPDM or PVC membrane etc., then for a sealed connection of the waterproofing with the drain body it is necessary to use a stainless steel flange HL83.0 (for EPDM/PVC membrane) or HL83.H (for bitumen sheet). Flanges are not included in the delivery set and must be ordered separately.
How does the Primus siphon work?
Siphon while draining water The water seal is drying out Siphon in a “dry” state
1. Siphon body
2. Float
3. Air in the float body
4. Water (water seal)
Components of the HL 310 NPr drain:
|
|
grille HL 037Pr.1E |
|
|
Mounting plug HL 037N.0E |
Add site to bookmarks
- Kinds
- Choice
- Installation
- Finishing
- Repair
- Installation
- Device
- Cleaning
How to choose and install a sewer drain?
Today, many people prefer to implement their ideas for organizing a bathroom instead of installing standard shower cabins. In accessories and finishing materials there is no shortage. If you do without a pallet, you can significantly increase usable area and create your own shower stall design. In order for all these advantages to “earn”, you need to know how to install a floor drain. Without the right one, there is nothing to think about the comfortable use of the bathroom.
Proper installation of a drain will help avoid flooding your neighbors and damaging your bathroom renovation.
What types of ladders are there?
The material used can vary, and these products can be metal, aluminum, plastic, cast iron, or a combination of metal and plastic. The shape of the ladders also varies, but the most common are round, square and rectangular. The height of the products varies from 75 to 180 mm depending on the model. They are all similar in design and consist of the following elements:
- Front panel (grill). May have different sizes and the shape of the drain holes.
- Siphon. Designed to prevent the penetration of odors from the sewer system. It can be made in several versions: water seal, dry seal, mechanical seal. The latter is installed on outdoors or in non-residential premises.
- Seal.
- Elements for sealing (clamping).
- Frame.
Structural features of ladders
- Horizontal. The most commonly used type, since its installation is possible on any floor, regardless of the number of floors.
- Vertical. They differ significantly more throughput, but require special conditions installation
Return to contents
What to consider when choosing a ladder?
It is important to choose the right drain, since after installation it will be difficult to dismantle it: you will need to remove flooring and a screed.
Floor drain structure with combined system shutter
The material used is not that important; everyone chooses what they like best. Nowadays, plastic drains are the most popular, since they have the most interesting design, there are different color combinations. You can buy without fear hardware, they are durable and not subject to corrosion.
You need to decide on the size of the ladder. For showers, they are suitable for medium-sized showers with good flow capacity. If the drain is needed in a drainage or other system, then the size is determined based on the expected volume of drainage. An important point is the configuration of the drainage system in the place where the drain will be installed. For example, the design of household sewer systems allows you to connect up to 3 outlets (pipes from a sink, sink, etc.). The direction and diameter of the outlet is very important, this point must be taken into account.
Optimal characteristics
Corner drains have a PURUS Nood mechanical water seal.
- throughput of at least 1.2 l/sec;
- built-in siphon;
- if in the house sewer pipeline plastic with a cross-section of 110 mm, then the drain must have sleeve connections of the same diameter for vertical drainage or 50 mm for horizontal drainage;
- the grid must be designed for load class A;
- the design of the ladder must ensure adjustment of its installation depth in accordance with the level of the floor covering;
- equipped with seals;
- It is advisable to have installation instructions.
Return to contents
Which drain is better: with a dry or hydraulic seal?
Until recently, manufacturers produced products only with a hydraulic shutter. What is he? This is a tube bent at a certain angle that contains liquid. This is precisely the obstacle that odors coming from the sewer system cannot overcome. Caring for such a shutter is simple: just periodically spill it with water.
What is the disadvantage of this design? The fact is that the shower valve dries out when used infrequently: unpleasant odors are starting to cause inconvenience. is also possible for other reasons: design errors, increased room temperature, use of a “warm floor” system.
With the advent of drains equipped with a dry seal on the market, many problems resolved themselves, and these designs became very popular. Such products are also convenient in that they can work either independently or in combination with a water seal.
Return to contents
How is the shutter at the ladder arranged?
Return to contents
Membrane
The valve is equipped with a membrane to which a spring is attached. When water is drained, the membrane opens and lets it through, and when the flow ends, it closes the inlet into the waste pipe under the action of a spring.
Return to contents
Float
On the surface of the water in the water seal tube there is a kind of float, which, as the water flow decreases, falls and blocks the passage hole.
Return to contents
Pendulum
Its work is based on the principle of gravitational force. Under its influence, the mechanical valve device always strives to take a position in which it blocks the pipe.
Return to contents
Installation of a sewer drain
Installation of products with dry and water seals is practically no different. The basic rule: the floor should be made in such a way as to ensure the proper level of slope to the drain for unhindered drainage of water into the riser. Therefore, installing a drain funnel often involves raising the floor level or dismantling the existing floor covering.
Basic installation rules:
The material of manufacture is not important, the main thing is that it is moisture resistant.
- the facing grid of the ladder must be flush with the surface facing covering gender;
- finishing begins with laying tiles from the ladder;
- seams between tiles should not exceed 2 mm;
- the grout used is moisture resistant;
- The floor surface must provide a slope for water drainage.
Materials you will need:
- cement;
- sand (sifted);
- waterproofing membrane;
- warmth and soundproofing material(foam is often used);
- mastic or adhesive composition for laying tiles;
- tiles that provide an anti-slip floor surface (rough).
If you need high-quality, convenient, inexpensive plumbing fixtures and want to find all the necessary items for your bathroom in one place, check out our online store. Our company is the official representative of many manufacturers, which means that we have exclusive rights to sell their products. This allows you to set prices at an affordable level.
Assortment of plumbing fixtures
Our catalog includes:
- shower cabins;
- baths;
- sanitaryware;
- bathroom furniture;
- faucets;
- shower corners and doors.
Buying plumbing in an online store means finding everything you need without leaving your home. The range includes heated towel rails, mini pools, water heating tanks, kitchen sinks, filters for water. We work with factories from different countries, such as Germany, Spain, Italy, China, Russia, offering furniture and equipment at competitive prices.
Having decided to purchase plumbing products from us, you don’t have to worry about their quality and durability. We cooperate with official companies that have been able to break into the global market and maintain their position in it with dignity. Our plumbing store is located in Moscow, there are representative offices in Yekaterinburg, Tyumen, Chelyabinsk, Perm, St. Petersburg. Wherever you are, no matter what you order, the goods will be delivered in a short time.
Why is it better to cooperate with us?
If you contact us for your purchase, you will not encounter large markups. Don't be afraid to order online because we carefully inspect your order before we ship it to minimize the chance of receiving defective products.
The quality of plumbing fixtures in the store site is confirmed by manufacturer guarantees, hygienic conclusions, and certificates of conformity. We adhere to the laws in force in the country; if a manufacturing defect is detected, we undertake to return the money or exchange the goods.
Features of the service
People contact us with questions related to the purchase of plumbing equipment. If you have no idea what to look for or which brand is better, visiting our showroom will definitely get your questions answered. Qualified and experienced specialists will help you make a choice you won’t regret. We often hold promotions and offer discounts, which adds benefits.
Would you like to buy plumbing fixtures in Moscow? good quality and cheap? Then stop at the Shower website, select the product you need and fill out the application. Payment can be made upon delivery or against an invoice. The website contains the addresses of our branches in major cities.