How to install a shower tray: practical advice from plumbers for home craftsmen. Installing a shower tray, instructions with photos How to install a shower tray with your own hands

DIY technology for making a brick shower tray

Someone who loves to design and implement design ideas original character, can make the pallet yourself. In this case, the owner can choose both the shape and color scheme.

Construction of a brick pallet

To install a homemade pallet, you will need to purchase a drainage device - a ladder. We will make the side of the pallet from brick.

It is better to purchase a high ladder, since such devices are characterized by high throughput.

Base installation sequence

The arrangement of the pallet is carried out in the following order:

1. They knock down at the work site flooring together with the screed, reaching the concrete slab.
2. A brick wall is laid along the border of the future pallet so that it is at least 50 mm higher drain hole(depending on the height of the ladder).
3. The ladder is disassembled into lower and upper parts (they are connected by two flanges). The lower part is connected to a sewer pipe with a diameter of 50 mm, laid with a slope of 3 cm/m. Usually the ladder is located in the corner. Remember that all connections will be inaccessible, so they need to be sealed not only rubber cuffs, but also silicone sealant. The pipe and drain must be fixed with cement-sand mortar.
4. Next, the site is covered with sheets of extruded polystyrene foam 50 mm thick, in which grooves are cut for all elements of the drainage system.
5. A layer of concrete approximately 40 mm thick should be laid on top of the expanded polystyrene - it should reach the flange of the ladder.
6. Hardened concrete is covered roll waterproofing, for example, roofing felt (fused using gas burner) or “Isoplast”, with mandatory release on the walls and brick side at least to the height of the subsequent layer of screed. For reliability, it can be laid in two layers. Above the gangway in waterproofing material cut a hole with a diameter corresponding to internal diameter flange.
7. The upper part of the ladder is installed, and the waterproofing will be pulled together by two flanges.

Having installed plastic beacons (to ensure a slope towards the ladder), lay a layer of waterproofing cement-polymer screed (for example, Ceresit CR65). Its surface should be lower than the drain grate by the thickness of the tile with glue. Along the corners along the entire perimeter, using adhesive mastic on a polymer-cement basis, you need to glue a waterproofing tape.

Photo: upon request from Yandex and Google

When renovating a bathroom, we first of all replace the finishing materials of the walls, floor and ceiling, and also update the plumbing. If your room is not spacious enough to install a large bathtub in it, then you can significantly “save” space with the help of a shower. This article will talk about how to make a pallet design yourself.

Types of shower trays by materials

Pallet- this is the basis for our shower stall, which means it must be made from really durable materials. They can be classified as follows:

• made of cast iron. These pallets are some of the strongest and most durable. Among the disadvantages are very heavy weight, long warm-up and high price.

• of steel. Very light, inexpensive and quite durable. However, such pallets have very fragile enamel and low sound insulation.

• from ceramics. These pallets are very attractive and easy to use. But they usually have no legs and are very fragile.

• from artificial stone. You will definitely be attracted by the surface texture of such a pallet, but low thermal conductivity, high price and heavy weight may discourage you from purchasing.

• made of acrylic. Practical, light, beautiful, absorbs noise well. Such pallets have only one drawback: they are susceptible to damage and deformation.

• made of wood. Suitable for a cottage or country house. Environmentally friendly material, but will last no more than three to four years.

• made of plastic. A very budget-friendly and short-lived option that we would not recommend for an apartment or house: rather, for a summer shower.

How to make a shower tray with your own hands: step-by-step instructions

For convenience, we suggest dividing the entire process into several stages. The first, important one, is the preparation of all the materials necessary for the work. So, you will need:

• A drain, in other words, a drainage system.
• Several concrete blocks or bricks (optional).
• A little sand and cement. It is also desirable to have plasticizers.
• Ruberoid or a couple of sheets of plastic film, a little water-repellent mastic.
• Among finishing materials – mosaic tiles or tile (at your discretion).
• Tile grout and good glue.

Now about the tools:

• A small bucket in which we will mix the solution.
• Mixer.
• Trowel (construction trowel).
• Laser or water level.
• A hammer drill, a drill, several screwdrivers of different sizes.
• Spatulas and roller.

Stage 1. Screed under the shower tray. First, the surface should be thoroughly cleaned of residues. old tiles, dust and dirt. Now we prime in two layers. As for the primer, it is better that it is moisture resistant. After the soil has dried, the shower tray is waterproofed. To do this, you need to coat it with a special mastic (be especially careful in treating the corners). Then a plastic film is laid on the floor (preferably a couple of layers). Once the mastic has dried, you can pour the cement screed. As for the thickness of the screed, it should be approximately five to eight centimeters.

Advice! When you lay the film, try not to exclude air gaps. If there are any, there will be no effect from waterproofing.


Stage 2. Install a shower drain and drain pipes, make a neck for water drainage. Before installing a drain ladder, you need to bring it to the place where the water drains. sewer pipe(the ladder connects to it). Pay attention to the installation height: the slope must be at least three degrees. Fix it well with cement-sand mortar. This stage is very important, because if you loosely secure the drain and its structure moves during subsequent work, the pan will leak inside in the future. As a result, the entire system will have to be disassembled.




Stage 3. Line the sides of the shower tray with bricks. After the waterproofing along with the drain is installed, we can directly form the shower tray. The sides around the perimeter of the pallet are made of brick. First, the shape of the future pallet is drawn up (the types of pallet shapes are shown in the photo above). The markings are done on the floor using a simple marker. According to the markings, we lay out our brick side using cement-sand mortar.

Advice! The proportion of the solution should be the same as for the screed: one to two. As for the height of the side, it should be close to the level of the grating of our ladder - plus twelve to fifteen centimeters. This will prevent water from leaking onto the bathroom floor.

Stage 4. Pouring the base for shower cabins. Again, we use cement, to which it is worth adding a little special hydro-repellent agent, for example, liquid glass. First you need to fill the layer up to the drain (horizontal). As soon as it dries, install several special beacons (plaster beacon slats). Thanks to this, you will form the right inclined plane.

Advice! Before pouring the base, make sure that the floor is strong. After all concrete base The shower tray is quite thick and, accordingly, weighs a lot.


Stage 5. Waterproofing the pallet. It would be useful to add another layer of waterproofing. Now on the completed structure of our pallet. We coat the base with mastic, as well as the external and internal sides. It is best to apply two layers. Now we can safely call the isolation reliable.

Stage 6. Shower tray lining, decoration. After the water-repellent mastic has dried, cover the pallet with cement plaster. The seams of the shower tray are treated with special care. Please note that the selected plaster must have increased resistance to moisture. also in mandatory used plaster mesh with a small cell. This way the layer of plaster will lie more firmly.

As soon as the surface is dry, we begin to prime it with a moisture-resistant primer (several times). As soon as the primer is dry, you can start working on the decor. Congratulations, your DIY shower tray is ready!

Do you know how to make a shower tray? Share with our users in the comments below the article!

If you don’t have the time or desire to make a shower tray with your own hands, then welcome to our catalog: you will find dozens of stylish and high-quality options from trusted sellers.

You may also be interested in:

A shower stall without a tray is not always convenient in an apartment, so it’s worth choosing a bathtub, because it’s easy to install it yourself. Which trays are best for showers?

To figure out how to make a shower stall with your own hands, you need to study everything possible options. This also applies to the design, the choice of water drainage system, and the selection of materials for the construction and decoration of walls, as well as interior design. Since the number of combinations of all these elements is very large, the output we can get is something unique, and isn’t this a reason for a true engineer and designer to be proud?

So, the shower stall is built approximately according to this scenario:

• Choosing a shower design;
• Pallet installation;
• Floor installation with a slope;
• Installation of cabin partitions;
• Selection of internal equipment.

Self-made cabins can be equipped with a shower tray purchased at the appropriate store, or equipped with a sloping floor along which water flows towards the drain hole. If in the first case everything is clear, then installing an inclined floor will require some additional knowledge from you. If you do not have sufficient skills in working with concrete, then it is better to stop at buying a ready-made pallet, since such pallets are produced in a huge assortment and are not that expensive.

The shower room includes a fence, also made by hand. It’s good if there is a suitable niche for its installation, in which case all that remains is to install special doors or make do with curtains.

When the area of ​​the bathroom allows you to install a cubicle without compromising comfort, then the partitions can be made in a common style with the rest of the room, which will have a beneficial effect on the overall atmosphere and comfort.

In addition, it is necessary to measure the bathroom space, determine the places where pipes for supplying and draining water will be laid, and provide for the possibility of installing light. You also need to decide in advance on the type of mixer, or maybe a shower column with additional options, such as hydromassage.

Pallet installation

If you decide not to tempt fate and buy a ready-made pallet, then to install it you need to prepare a flat area; it is advisable to place a concrete screed on the bathroom floor, after laying down a waterproofing material. This is necessary in case of an accident and subsequent repair of the drainage system. Before installing the pan on the racks included in the kit, you need to install pipes for water drainage and install a siphon. Pay attention to the installation height of the tray in advance, this will help you choose the appropriate siphon. Installation of the shower tray should be done using a long building level. To make it easier to seal the joint between the wall and the pallet, it is recommended to make a small recess in the wall and push the edge of the pallet into it. It is better to cladding with ceramic tiles or other material after installing the pallet.

Inclined floor device

If you decide not to buy a ready-made shower tray, you can build a cabin with an inclined floor yourself. With size and shape, in this case, nothing will limit you.

The main difficulty associated with installing a shower stall with a sloping floor is the need to raise the floor level to such an extent that water can drain on its own into the sewer system. To do this, you can lay out a shower curtain around the perimeter. For these purposes, you can use brick or foam concrete. The latter is more convenient to process and give it rounded shapes. The side must match the shape of the shower stall. Next, you need to connect the sewer pipe and install a drain. You should not use siphons designed for installation in a tray, as there will be problems with cleaning it. The ladder is installed lower than the height of the sides to ensure the required slope, which should be 3-4 centimeters. Channels for pipes can be installed in the wall. Such channels are cut with a hammer drill, and after installation they are sealed with concrete mortar. Also on sale ready-made kits drainage channels with ladders.

After installing the channels and drains, you can begin pouring the inclined floor. For these works they use concrete mortar with the addition of silicate glue. When pouring, it is necessary to take into account that the drain grate must be flush with the inclined floor, so it is necessary to leave a gap for the thickness of the facing material. The final surface should be sufficiently flat so that protruding areas do not have to be chiselled during cladding.

After work with the sloping floor is completed, you can begin laying facing tiles. Since such a floor is not a flat surface, it is most convenient to do this in small ceramic tiles, which are sold in the form of ready-made mosaics on a special substrate. For installation, use special waterproof glue.

Installation of cabin partitions

To construct enclosing elements, you can use various materials and their combinations. It is better to build the frame from a metal profile, but if you choose wood, you need to dry it well and treat it with a special protective composition To avoid rotting processes, larch has the best water-resistant properties. To build walls, many people prefer to use a material such as plasterboard, but we recommend choosing gypsum fiber boards; they do not contain cardboard, and as a result are more moisture resistant.

From gypsum fiber boards you can build a seat and shelves, which are subsequently lined with the same material as the partitions. Cladding work must be done with the same waterproof glue.

Partitions made from glass blocks look good. They are available in the most different colors, and some contain various decorative elements, such as: plant compositions, shells or starfish.

As a cheap alternative, polycarbonate or plastic panels. These materials do not need to be decorated; simply screw them to the frame with self-tapping screws.

It is very important to ensure a good seal between the pallet and the partitions; a special sealant is used for this. When working with such sealant, use an excess amount; the excess can be removed with a soft spatula or cut off with a knife after complete drying.

To arrange the entrance to the shower stall, you can use simple curtains that are hung on a rod using rings. The lower ends of such curtains are usually located inside the tray so that water falling on them does not flow out. If you want to see a more rigid structure in this place, then ready-made sets of special hermetic doors are available for sale. Such doors can be hinged or sliding. The latter are convenient because in the open position they do not take up much space. If you decide to install hydromassage in your shower, then ordinary curtains will not suit you.

If the ceiling of the bathroom is too high to install partitions under it, it is necessary to install a ceiling on the shower stall itself. Plastic panels on a frame are best suited for this. It is convenient to install additional lighting and hood in such a ceiling.

Tag Cloud:

DIY shower cabin without tray

The acrylic shower tray is collapsing around the steam generator nozzle. Two years ago the acrylic was already repaired, but now cracks have appeared over a larger area.

Last time they explained to you that the Chinese steam generator produces steam that is too hot for acrylic, although the tray itself is very good.

We'll fix it again, but now we have to think about what to do with the steam.

The Chinese acrylic pan is cracked and leaking.

The hot water deformed the plastic and peeled off from the fiberglass.

The reinforcing layer is full of holes, so the sawdust under the bottom has rotted. Now the bottom bends a lot, so it cracks even more. We need to make a new bottom.

Cracks and chips on the bottom acrylic bathtub. I put a glossy magazine so that you could see the color of the acrylic in the photo. What and how can you do?

The crack runs along the frame channel. This means the bottom is weak. Chips are nonsense. We'll have to strengthen the bottom. The color of the bath is clear and available. We'll handle it during the day. It will be durable and quite beautiful.

Shower cabin Aqua Joy AJ-A-120A L (size 120x80x215). Country of manufacture, when we bought it, they wrote that it was
Kaliningrad, although most likely China. Two thin parallel cracks, each about 35 cm long, appeared at the bottom of the pan.

Water does not leak from them onto the floor. It seems to me that if you step between the cracks, then in this place the bottom bends down. But it’s difficult for me to understand whether this place falls on the convex or concave part of the bottom relief (the photographs show the bottom topography from below).

After the cracks formed, the cabin began to squeak a lot when you were in it, but after some time during the washing process, the creaking almost stopped.

Chipboard stiffening ribs are glued under the bottom of the pallet.

In theory, there should be a solid slab of chipboard, not pieces. Saving on sawdust. The plastic is very thin and bends and breaks along the stiffening rib.

The acrylic has already cracked, and the polyester putty with fiberglass underneath has not yet had time to break. That's why it's not leaking yet. During the washing process, the reinforcing layer gets wet and creaks less. The bottom needs to be strengthened well. There is no point in doing anything under the bottom unless you build additional support. We will work with front side. It seems that it can be done very firmly and almost imperceptibly. It’s hard to say exactly how many hours you’ll have to work, but we’ll do it in one day.

My shower tray leaked on the Serena SE-12013G high tray, 90x90, round.

Apparently, there is a delamination of the acrylic, and maybe a break (it is pressed when pressed). There is a small crack inside and outside (but in slightly different places, not through). The pallet is undermining. How much will the repair cost, and is repair possible, or does the pallet need to be replaced?

Judging by the description, the Chinese acrylic tray broke under the weight of a person.

Since the cracks on the pallet and under it are in different places, this means that the plastic has become deformed and peeled off from polyester resin with fiberglass. The strength of the trough has decreased significantly.

How to install a shower cabin with your own hands

It should be strengthened on both sides if possible. The cost of the work will be slightly higher than the minimum order value.

The acrylic shower tray is cracked and leaking.

It bends a little. What can be done?

An ordinary Chinese grayish flimsy pallet, that's why it broke.

It is necessary to thoroughly strengthen the place where the hole is, and at the same time the entire bottom. You can also support it from below. Choosing a color is not a problem.

My pallet broke in the “first step zone”, a crack 1.5-2 cm long, along the entire length of the “pimples” (the pallet has a pimply surface, in squares).

From below in this place one of the beams of the fastening cross passes, at the end of which legs are installed. And if you look at the pallet from below, there is a delamination of acrylic (I think) to the right of the crack, you can see brown stains, through which water drips (collects and drips).

But they are not end-to-end. I'm sending photos. The plumber coated the inside of the pan with something like liquid rubber, I don’t know for sure, but it casts off easily if you pull. The pallet itself
tall, quarter circle, 90x90cm. Is it possible to repair the pallet? In what time frame can this be done?

The profile of the frame cross almost does not touch the bathtub.

No under pallet for strength chipboards. There is only fiberglass, which broke safely. The acrylic peeled off from the polyester resin.

The pan is leaking because the acrylic and fiberglass are torn. You will have to work under the pallet and in the pallet.

We'll get it done in a day. It will turn out beautifully.

Tell me how much it will cost to repair the bathtub - see the through damage in the photo - temporarily sealed with tape. Dimensions approximately: 30*5 mm. The sliding door fell.

In the photo, you can't see if there are any cracks around the hole.

The complexity of the repair depends on this. In any case, it can be fixed. It will turn out more beautiful if you can reach the hole with your hand from the outside.

A shower cabin is installed in the beauty salon. I would like to update the coating to make it look good.

The photo shows damage from chemicals under the water intake hole and on the nozzles; most likely there are cracks there.

Near the steam generator, the acrylic is damaged by hot steam and, possibly, aromatic oil. There are cracks in the bottom of the shower tray. The sawdust under the plastic has swollen and in those places where the frame profiles are located, the acrylic is torn. It seems that there is little point in repairing this Chinese pallet; it won’t work out beautifully.

Hello!

We retail shower cabins that we ourselves imported from China. During transportation, some pallets were damaged - approximately 20 pallets (scratches, cracks and chips). Would you like to offer you to repair/restore our pallets (for further sale)?

It is impossible to RELIABLY seal CRACKS on Chinese pallets so that they are completely invisible.

Recording a low pressure shower. One of the eternal questions that every person encounters in his life is the choice of a bathtub or shower.

Currently shower low level can be considered one of the most hygienic and practical options. The cabin installation instructions will help you deal with any possible problems.

When installing this format in the bathroom, you can reduce water consumption by water procedures Besides, you don't spend a lot of time lounging in the bathroom and relaxing.

One of the most important issues is the height of the side of the pallet. Depending on what the owners of the house are.

Low range showers are those that have a side height of 0.5-1 cm. For all people, this height is comfortable. If, however, elderly people or small children live in the house or home, it is important that the cabin is as comfortable as possible for all family members.

Shower enclosures with a low palette are a modern and aesthetic option.

You can easily step on the bottom to use the shower.

Advantages of a low tray

Using a low pressure shower has many positive aspects:

• all models are sorted by model, so they fit perfectly into any interior and become more alive;
• Shower for low temperatures perfect for small room, its installation does not take much time;
• models of this type are very diverse, completely complement the interior and fit perfectly;
• Due to the low palette and the presence of a tight door, water does not fall on the floor; in addition, the interior is very simple;
• Taking water in the bathroom is very convenient to accompany a child or help the elderly.

However, the cabin installation has a low defect spectrum.

weak sides

Disadvantages of low level pallets include the following:

• such models do not always have good sealing, so you need to install curtains or doors;
• The low sides make it impossible to collect water to buy a child. You also won't be able to use the tank to store different types of products;
• The tray heats up very slowly, which may cause discomfort to many people.

Variety of low range showers

Shower enclosures vary depending on the materials from which they are made and depending on the type, shape and availability of certain functions.

How to install a shower with a palette yourself

Pallets are often made of cast iron, steel, spores or acrylic:

• Cast iron is a material that is not only heavy, but also very expensive. Significantly maintains heat compared to steel and acrylic;
• a steel tray is “louder”, it can also bend under the weight of a person;
• many people prefer acrylic because it softens the sound of water, it is more durable and comes in different colors;
• quarrel - very interesting material, which combines the advantages of acrylic and the beauty of a stone product.

  If desired, the shower cabin can be made from natural stone by individual order.

If the size of your bathtub allows you to purchase a larger stall, you can choose a model with a sit-on seat.

In some low concentration showers you can use fragrances and music. These models have a touch screen that allows you to switch modes.

Shower cabins with sliding doors are very popular.

But if you have enough space in your bathroom, you can install a model with a swing door.

Corner models of low-class shower cabin - great option for very small bathrooms.

In addition, if you want to install such a device, you do not need to have special skills - it is very important to simply approach this issue responsibly and familiarize yourself with the stand installation diagram.

Installation of shower cable

When shopping for a shower, consider your bathroom options.

Don't forget that the choice of cast iron pallets will be good decision, as they are durable and easy to use.

If you bought simple model with low light, you can watch installation instructions video online. Here you can find out what tools you will need to install the structure.

Installation of a shower product can be roughly divided into the following stages:

• siphon installation, which means the placement is below the bottom of the shower.

  The lower part refers to the installation location, describing the example and drains. When it moves to the intended area, a low siphon is installed.

  The cabin is then fixed and the pallet is loaded and compressed;

• Wall installation begins with the assembly of the locks or frame, as well as the vertical stand. After this, the fabrics are inserted into the recesses and secured with rubber parts. For strength, the walls are screwed in. Use self-tapping screws and fasteners to perfectly fit the profile.

  If you want to cover the screen of the closed storm cable more tightly, you need to connect the canvas to the frame brackets, then pull it and grease the profile parts;

• door installation. The fabric door is attached to the top and bottom through specially prepared holes.

  The doors are first connected to the rollers at the top and then the buttons are used for alignment. On a suspended canvas in the upper part it is mounted on lower rollers by a spring. This completes the installation process.

If you are confident in your abilities, you cannot invite professionals to install the shower and do everything yourself using special designs.

Installing a short-range booth is not a complicated process, but it does require some skill. If you are careful and pay attention to details, you will get a shower that will keep you strong and safe.

The differences in a deep bowl setup aren't that big of a deal, so you shouldn't have too much trouble.

For the manufacture of shower trays, various materials are used, the properties of which determine the characteristics of the finished products. Today we want to talk about steel models, consider their advantages and disadvantages, and also pay attention to how to install a steel shower tray with your own hands.

Steel shower trays

Characteristics and Features

If we look at shower bowls and divide them into groups according to the materials from which they are made, we will notice that steel products will be the most budget-friendly:

Cheapness is one of the indisputable advantages of steel models, but it can also have the opposite effect: most buyers believe that low cost is a sign of low quality.

This is not entirely true, and often the low price is caused by the peculiarities of product production, the cost of materials, as well as (and this is especially important) existing market trends and the related marketing policies of product manufacturers.

When steel pallets It’s impossible to say that they are definitely worse than their analogues, but in some positions metal models really lose. Their lineup is not that diverse, especially in terms of design. Quite difficult to find the bowl unusual shape, square and rectangular shapes, corner models are much less common.

There is also a limitation on the depth of the vessel, and it is almost impossible to find really deep steel shower trays, since this parameter is limited to 160 mm. At the same time, models with a maximum depth of 130 mm are more common, and any pallet with a depth of more than 40 mm is called deep. However, this feature is not unique to this class.

On the other hand, steel is an excellent structural material, which is characterized by high strength and durability, which is not afraid of high temperatures, shocks, falls of heavy objects, fungal infections and other similar influences. Low cost makes steel models especially in demand for installation in country and country showers.

The products are made from carbon steel coated with anti-corrosion wear-resistant enamel. If you remember cast iron bath, then you can imagine what we are talking about. The bowl can be equipped with a frame for installation, special legs or supplied without them.

Important!
By the way, bathtubs can last for decades and still look good, so stereotypes about the quality of steel bowls are largely far-fetched.

Advantages and disadvantages

Despite their low cost, steel pallets have a number of advantages, thanks to which the demand for this class of products remains quite stable.

We list the main ones:

• High strength characteristics of steel. The material is not afraid of high temperatures, does not crack, does not split, can withstand significant weight, and withstands impacts and falling objects;
• Low cost. With quite acceptable quality, the products are several times and orders of magnitude cheaper than analogues made of ceramics or artificial stone. Even acrylic bowls cost about two to three times more;
• Possibility to choose enamel color. Unlike ceramic and acrylic counterparts, steel bowls can be coated with enamel various colors and shades, which makes it possible to fit it much more harmoniously into the interior of the bathroom;
• Easy DIY installation. The product is quite easy to install using ordinary tools, without any special skills in construction or plumbing.

Important!
When installed on a frame, the need for wet processes and brick podium construction is eliminated, making installation much easier and faster.

Of course, there are also disadvantages.

We will list only the most significant of them; if they do not confuse you, then you can ignore the rest:

• Steel is afraid of electrochemical corrosion. Enamel coating may become detached from the surface or damaged by mechanical impact, and then the bowl will begin to actively rust and deteriorate;
• The appearance and variety of forms leave much to be desired;
• Steel surfaces are very slippery, especially if they are not corrugated;
• When water flows from the shower, a noticeable noise occurs;
• If there is no frame under the bottom or solid foundation, it can bend under the weight of an adult. This is dangerous due to cracking of the enamel.

Important!
It should be noted that, unlike steel, it heats up quickly enough from water, and you can use the booth practically without preheating the bowl.

Installation

Installation of steel pallets is done in two ways: on a podium made of brick or concrete, as well as on a special steel frame with legs. It is advisable to choose a model with a frame and adjustable legs.

If there is no frame at the installation site, a brick podium is first laid out. To do this, the floor is stripped of finishing down to a clean screed, on which a ceramic brick structure is laid (silicate brick is not suitable due to low moisture resistance).

The design is a parapet 0.5 - 1.5 bricks high around the perimeter of the bowl: