Shop sizes. How to make a garden bench with your own hands

DIY bench: drawings with dimensions, photos. How to make a bench with a wooden backrest with your own hands.

A light garden bench will come in handy for relaxing in your country house; on the bench you can sit in the garden and relax in the shade of the trees. Wooden benches will harmoniously decorate your relaxation area in your summer cottage, and if the bench is also made by yourself, it will become a source of pride for the owner.

Materials for making a bench:

• Boards with a section of 20 x 100 mm or similar size.
• Screws.
• Varnish or paint.

Tools:

• Hacksaw.
• Plane.
• Tape measure, square, pencil.
• A screwdriver or a shaped screwdriver.
• Drill with a drill with a diameter of 2 mm (the diameter of the drill should be less than the diameter of the screws).

Bench assembly diagram.

1. - legs.
2. - frame.
3. - backrest supports.
4. — seat slats.
5. — backrest strips.

How to make a bench with a back.

The pictures provide detailed drawings with dimensions for making a garden bench.

Let's start making a garden bench, and start with making the legs for the bench.

Mark the cut lines on the board and use a hacksaw to cut off the leg blanks. Smooth the ends of the legs sandpaper.

Assembling the sides of the bench.

We attach the upper support to the front and rear legs. Align the legs with the support, drill holes and secure them with screws. Let's make two sidewalls.

Assembling the bench seat frame.

We saw off the blanks for the seat frame. We combine the frame blanks, drill holes and screw in screws.

Assembling the frame and sides.

Now you need to connect the sides of the bench and the seat frame.

The back of the bench.

We saw off 3 supports for the back.

We install and secure the seat back supports as shown in the figure.

Install the slats to the seat frame, making sure you place them at equal distances, drill holes and secure the slats with screws.

Now secure the slats to the backrest supports.

Attaching armrests.

Place the armrests on the sides of the bench, drill holes in the armrests and secure them with screws.

The screw heads can be hidden by covering them with wood putty and then allowing the putty to dry for several hours. Sand the hardened putty and then apply several coats of paint or varnish to the bench to improve the appearance of the bench.

How to make a bench photo.

You can relax calmly in the shade of trees in the summer or bask in the sun on a cool autumn day on a wooden bench that you installed in the garden yourself. IN modern design garden furniture is one of the full-fledged elements of landscape design.

Taking into account the decorative value of garden benches made of wood, you should try to choose a model that will harmoniously fit into environment. For a young garden or summer cottage without big trees It is better to choose light furniture options with decorative thin metal legs, simple benches and benches that are laconic in shape. If the garden is old and well-groomed, then seats in the Provence style are suitable - with stylization like antique furniture with wooden decor.

Overgrown country cottage area with an imitation of a wild natural thicket I can decorate benches made with my own hands from natural material- driftwood, driftwood, lightly processed branches. A bench made of logs hewn with an ax would look very good in such a garden. Such seats should be installed in places hidden from view: among flowering bushes or around the bend in the path.

When choosing a place to install a bench for a summer house, you need to pay attention to the views that will open to the eyes of those sitting on it.

It is not advisable to place the bench in such a way as to contemplate an unsightly fence or compost heap. Place it near a pond or flower bed, under a branchy old tree.

Then your relaxation will be complemented by the pleasure of the smell of flowers and the play of light on the water, the rustle of leaves and coolness in the shade.

Various types of benches can be installed on the veranda near the house, in the relaxation area by the pool or outdoor fireplace. They will also find use under a canopy in the garden. In each case, you must adhere to general rules compatibility wooden product with the general style of the site. How to make original benches from pallets, watch this video:

As a material for garden furniture wood is traditionally chosen - an easy-to-process material that allows you to bring almost any idea to life. Currently, along with regular board and as a block, you can use moisture-resistant varieties of thick plywood. Made from durable and aesthetically pleasing sheet material you can assemble designs that are suitable for modern designer landscapes and for an ordinary courtyard that does not have certain style characteristics.

If wooden benches are made in stationary version, then care should be taken to protect them from moisture. A variety of impregnations and paints and varnishes. Outdoor furniture you will have to paint or varnish every 1 to 2 years as the protective layer wears out. Such measures can significantly extend the life of a wooden structure.

How to build benches yourself?

To build with your own hands a comfortable bench, you need to make a sketch of it. Exist optimal sizes garden furniture, which must be observed in this case:

• seat height above the floor - 40 - 50 cm;
• width (depth) of the bench - 50 - 55 cm;
• The height of the backrest above the bench is 35 - 50 cm.

These dimensions allow a person of average height to sit comfortably, lean on the back, and stand up easily. If the owner’s build differs greatly from the average, then the dimensions of the bench will have to be selected individually. The backrest is usually made with a slight tilt back. For more information about wooden benches, watch this video:

To work with wood you will need the following tools:

• hacksaw or jigsaw;
• drill and screws, or hammer and nails;
• roulette;
• pencil.

For product assembly complex shape Wood glue may come in handy. It is used to fasten parts that are connected using the tongue-and-groove method or with a furniture dowel. For plywood products, long metal threaded studs and nuts are useful.

A simple bench for a vegetable garden or bathhouse

Even a novice craftsman can make a simple wooden bench with his own hands. Such benches can be seen in abundance at the gates of village courtyards; they can be placed near the beds, in a bathhouse or utility room. They are not distinguished by their sophistication and decorativeness, but they can perform the functions of garden furniture quite successfully. To make a bench you will need a board 2 - 2.5 cm thick and about 20 cm wide.

Benches for a bathhouse or vegetable garden are easy to make

According to the drawing in Fig. 1. you need to cut out the following parts:

• seat - 1 piece;
• apron - 2 parts, the length of each is 10 cm shorter than the seat;
• legs - 2 parts.

File off the corners on one side of each apron piece as shown in the diagram. Measure 2 - 2.5 cm from the edges of the element for the legs on each side in the upper part, cut a groove 10 cm long. If desired, cut out holes for the handles on the bench seat. To learn how to make a bench with your own hands, watch this useful video:

Assemble the product in the following sequence:

1. Drill holes for self-tapping screws in the plane of the apron board at a distance of 10 cm from each end. Place the board in the groove on the leg parts and screw the screws through the holes into the edge of the board. Attach the 2nd leg pattern to the other side of the apron.
2. Repeat all steps and attach the apron to the other side of the bench base.
3. At a distance of 15 cm from each end of the seat, make several holes in the plane of the board. Place the part on top of the base and attach it with self-tapping screws, screwing them into the end of the leg part. For strength you can do additional holes along the length of each side of the seat and attach it to the apron boards.

Sand the surface of the product with coarse sandpaper to remove burrs. If necessary, paint the bench to your taste.

Simple bench with backrest

Another simplest project shown in Fig. 2. To make a bench with a backrest with your own hands, you will need 2 pieces of logs about 25 cm long, boards for the back and seat, and 5x5 cm bars for the backrest posts. If you want the seat to be a little higher, you can take 4 pieces of logs or timber and lay them on top of each other, fastening them with dowels.

The back is screwed on with self-tapping screws on the reverse side

Making the bench is very simple. To ensure that there are no nuts or nail heads on the surface of the product, fasten the parts using dowels and glue. The back can be screwed with self-tapping screws from the wrong side so that they do not drill through the board.

To make dowels, you need wooden rounded rods (a thin handle is suitable for garden tools). Drill 2 holes in the log with a diameter equal to the thickness of the dowel. Based on their location, make corresponding recesses in the underside of the seat. The work must be done very carefully so that during assembly you do not have to adjust parts of the bench. For more information on making a bench with a back, watch this video:

Lubricate a piece of wood for the dowel with glue and insert it into the hole on the log so that a small fragment remains outside. Its length should be equal to the depth of the recess drilled in the seat (Fig. 3). Lubricate the dowels with wood glue and place the board on them. Do the same with another piece of log.

Cut the bars to the required length to make the backrest posts. Screw it to the ends of the logs with self-tapping screws. Drill 2 holes in the upper part for attaching the backrest. The distance between the holes should be less than the width of the board. Screw the screws through the holes into the board. The finished bench can be painted or coated with clear varnish.

Stylish bench with backrest

Making garden furniture according to the proposed project is not difficult at all. The basis of the structure is slabs of porcelain stoneware or concrete and boards 2 - 2.5 cm thick. If desired, heavy materials can be replaced light plywood the same thickness. A wooden bench with a back will be mobile.

Stylish bench has an interesting backrest

The following parts will be required:

• squares 50x50 cm for legs (plywood or board) - 12 pcs.;
• boards or plywood rectangles 15x200 cm - 5 pcs.;
• backrest supports 15x65 cm - 4 pcs.;
• crossbars 15x17.5 cm - 2 pcs.;
• threaded rod M16 55 cm - 4 pcs.;
• nuts and washers M16 - 8 pcs.;
• self-tapping screws

The plywood will first have to be cut into fragments of the required shape and size. If boards and slabs are used, this step can be skipped. To learn how to make an original bench with your own hands, watch this video:

Drill 2 holes at an equal distance from the edges in the upper part of the square parts of the legs. Adjusting the long parts of the seat as in the diagram (Fig. 4), make 2 holes in them on each side. Screw a nut onto one end of each rod and put on a washer. Alternating long and square elements, assemble the bench. Tighten the nuts on the other side of the studs.

This bench can be used without a backrest.

But for convenience, you can do it too. To do this, fix 4 boards 15 x 65 cm with self-tapping screws from the inside of the back of the bench. Glue crossbars between them or place them on dowels.

Decorative benches made from natural materials

Untreated wood is an excellent material for garden furniture. The bench, similar to the throne of a forest king, fits perfectly into the landscape, imitating wildlife. Such seats are very appropriate near rockeries or old trees with a spreading crown in an overgrown corner of the garden. Rustic benches go well with picnic areas trimmed with wild stones or barbecues made of sandstone and boulders. Original shop in this video:

The simplest option for sitting from logs is a monastery bench. To make it, a raw log needs to be sawn in half lengthwise. Legs are made from short sections, laying them cut down on the ground. Long halves of logs are secured to dowels from above, cut side up. To prevent the bench from staining your clothes, it is better to choose logs hardwood and dry them well before assembling the furniture.

To remove splinters and burrs, the cut plane must be planed smoothly with a plane and treated with emery cloth.

A complicated version of such furniture is a bench made of logs, supplemented with a backrest with your own hands (Fig. 5). To attach the backrest, you need wooden or metal supports and a crossbar. These parts can be made from thick wood branches, timber, or steel strips. Fastening is carried out using self-tapping screws of sufficient length or nails.

Examples of original wooden benches

A log bench can be made in another way (Fig. 6). The photo clearly shows the grooves in the upper part of a thick log sawn in half. You need to insert a board at least 4 cm thick or a beautiful cut of a tree trunk into the grooves. If desired, an exclusive piece of furniture made by yourself can be supplemented with a backrest. The supports for it need to be attached to inside legs on a flat surface. The crossbar can be a thick branch or the same cut of wood as for the seat.

Chopped table with benches

A set of table and benches will be convenient at the dacha in the dining area or near the barbecue (Fig. 7). It’s not difficult to make one if you know the basic techniques for making wooden log houses. To begin with, 2 logs of approximately equal thickness are placed on the ground. With an ax you need to cut out semicircular recesses (bowls) at the ends of the logs. The size of the bowls will depend on the diameter of the log that is chosen for the seats. This trunk needs to be sawn lengthwise. An example of chopped furniture in this video:

In the middle of the 2 lower logs, you need to cut out 1 more cup to install the transverse support. It may not be very thick log. Its length should be such that the ends protrude beyond side surfaces trunks.

For the table base you need shorter logs. Their length is approximately equal to the desired width of the tabletop.

In the middle of each trunk, you need to cut out recesses that are suitable in size to the thickness of the crossbar. Lay the parts of the log house with the cups down, covering the transverse log with them. Make a tabletop from the boards and secure it with nails. Place the halves of logs in the places designated for them.

How to make benches from branches or driftwood?

This is the most creative activity. Having found beautiful driftwood and polished driftwood trunks in the forest or on the shore of a reservoir, you can make furniture of amazing beauty (Fig. 8). Each such bench is unique, because it is difficult to find 2 identical branches. Therefore, there can be many solutions for how to make a bench from driftwood.

The main thing for all such products is one thing - the parts are adjusted directly on the spot to fit the already finished legs, seats, and backs. The branches should intertwine harmoniously, forming a structure that will support the weight of an adult. To connect non-standard parts, you can use both self-tapping screws and nails. The most reliable connection is with dowels and glue. Where a tight fit of the pieces of the structure is desired, driftwood can be trimmed with an ax.

The most original benches can be made from branches and driftwood

Such decorative benches can even be used to decorate rooms in a chalet or rustic style. They go well with wild stone trim. They will look harmonious in the garden among flowering bushes or near a pond.

The variety of models of benches that you can make with your own hands from wood is limitless.

The main thing in making furniture from wood is the careful fit of parts.

Then ready product It will turn out neat, without distortions. Treated with moisture-proof impregnations and coated with varnish or paint, any garden seat will last for many years.

Garden furniture can become not only an interior decoration, but also an excellent place to relax. A do-it-yourself bench is a source of pride and a foundation for the future furniture set.

Making this accessory is not as difficult as it seems. It is important to decide on the material and suitable design from the very beginning.

About materials

Plastic parts

Such a bench will have many advantages.

• Affordable price category.
• Easy care.
• Mobility.

Pleases big choice color options.

Plastic furniture also has its disadvantages.

1. Cheap look. Unlike wood.
2. Ability to fade in the sun;
3. The surface quickly deforms.

What about the tree?

Ideal for making furniture. Amenable to any type of processing, has a noble appearance, does not require complex work during installation. Any type of wood can be chosen. The main requirement is the absence of defects and high-quality drying.

Stone products

Material natural origin with an attractive appearance. Will fit into any interior design. The composition will look stylish and unusual, elegant. Natural stone has many advantages, but is not without its disadvantages. This option is also easy to do.

• It is not always safe to sit on such benches, for health reasons as well. Wood has no such disadvantages.
• It is recommended to purchase pillows and warm blankets as a set.
• Such benches cannot be moved from place to place; only stationary installation is possible.

What about metal?

Garden benches made using the forging method, cold or hot, will be an excellent decoration in any garden.

These are stylish and beautiful designs for which it is better to purchase decorative ornaments. Metal will be a good complement to glass or wood. Keep it simple.

Requirements for the bench

1. Convenience. The bench should be ergonomic; this is especially important for relaxation. Comfort and convenience play a role. Good option– the presence of a back in the product.
2. It is important that the bench can withstand even serious loads. Accordingly, the quality of fittings and furniture should be at their best.
3. The material must withstand any changes without deformation weather conditions, because it is created for outdoor installation.

Design and its features

1500 millimeters - this length for the back and seat of the bench is enough for three people to sit comfortably. Other dimensions also matter. The seat width reaches 400 mm, the back angle is 18-20 degrees. The height of the backrest is 900 millimeters, the height of the seat is 450.

From the materials we need to take:

• Varnish, primer;
• Sandpaper effect for wood;
• Screwdriver;
• Electric planer for wood. We will use it to process chamfers and polish the surfaces of boards.
• We will cut the boards using an electric jigsaw.
• Required number of screws.
• We will strengthen the structure of the bench with our own hands using self-tapping screws with dimensions of 40 by 40 mm.
• We make blanks for the front legs of the bench. Thickness – 35-40 millimeters, size – 360 by 150.
• Holders for the back and legs of the bench also require separate blanks. The thickness is the same 35-40 millimeters, but the size is 900 by 150.
• Do not make a product with your own hands without wooden planks. The thickness is the same, and the dimensions are 1500 by 150 mm.

We make a wooden structure

• You can immediately purchase boards of the required size for the bench. If suitable option no - we use a jigsaw to cut the boards with our own hands. Miter saw will also become an indispensable assistant. This can be done quickly.

• The wood must be carefully processed after the desired length has been achieved. Sanding requires blanks for the seat and backrest. You need to use an electric planer to process the ends of the boards. The best option– rounded shapes.

• We set the correct angle of inclination with our own hands to the long rear legs of the bench. They also play the role of the frame of the entire structure. We apply markings to two wooden blanks with a length of 900 millimeters. It's not all that difficult to do.

• 400 millimeters is the height of the bench; we mark it with our own hands first. Additional processing No material is needed in this area. We make a 20 degree cut along the entire length of the product, starting from the segment. This is how the angle of inclination for the backrest is formed. The angle of inclination and height on the two legs at the back should be the same.

• The bench legs are assembled first. 280 mm – distance between elements front and rear. The beam that connects the legs is cut across the entire width of the bench. Its size is 500 mm. It’s good if the strapping is on top and bottom.

• The sides of the bench are connected to each other with your own hands after the assembly is completed. To connect, we use boards on which you will need to sit. They are screwed to the upper bars of the trim using self-tapping screws. Gaps between wooden blanks must have different sizes. They help remove moisture and organize circulation.

• Let's move on to strengthening the bench with our own hands. Without this action, the product will not be durable and stable. We use timber to make bottom trim on the legs. We screw two blanks with a length of 1500 mm to the front and rear elements. There can be only one crossbar if there is not enough lumber.

• We install the backrest in the bench with our own hands. This is one of last steps. It is recommended to maintain a distance of 380 millimeters from the seat for the second board, 200 millimeters from the seat for the first.

• All that remains is the final covering of the bench. Varnish and deep impregnation will always help provide maximum protection against external influences. You can forget about pests, mold and moisture.

Related article: Note board: 3 super master classes

How to work with metal?

Garden plots are decorated not only with furniture made of wood. Metal can also become an indispensable assistant in creating comfortable places to relax. It is not necessary to master hot forging techniques for this.

Cold forging is also quite suitable for this. We simply weld a frame from metal blanks into a single structure. Decorative elements will enhance the appearance.

detailed instructions

• We start with developing the dimensions and dimensions of the bench. Standard height backrests – 800-900 mm. Width – 400-500 mm. Length 1500 mm. The most simple work– with angular shapes. It is recommended to start working with simpler models.

• We make a frame for the seat. We cut out a metal pipe. The dimensions we need are: 2 fragments of 400 mm and 2 of 1500 mm. We weld the parts so that they become rectangular shape. It is permissible to weld 2 additional stiffeners to make the structure more durable.

• Next we need legs. Metal pipe cut into 4 parts, 460 mm each. The blanks are then connected to the corners of the bench. Additional stiffening ribs between the front and rear legs will not be superfluous.

• We make the back. We weld together one piece 1500 mm long into another 440 mm long. We then weld the structure to the part of the bench, which is already ready. 15-20 degrees – optimal angle backrest tilt. Then your vacation will be comfortable.

• The backrest can also be strengthened with stiffening ribs.

• At the final stage, all seams are cleaned. The frame is coated with a primer.

Beam and board: the simplest forms

Execution and design options exist a large number of. There are also the simplest ones, some prefer wood carving. They become real works of art.

A wooden bench without a back is the simplest solution. It is allowed to use boards up to 75 mm thick. Each element consists of two parts.

We assemble a seat from two boards, the ends are beveled. It is better to provide a gap between the elements if you plan to place the structure on open area where there is no heating. The gaps compensate for the swelling of the wood and allow you to get rid of moisture in large quantities.

Related article: How to make a beautiful and durable metal bench

Each leg consists of two glued elements. A pin or dowel will make the connection more reliable. Two short beams for support must be secured to each of the legs. This will allow you to secure the seat itself. Self-tapping screws and glue, grooves – irreplaceable helpers for fastening. Beams and legs are attached to each board during the final stages of work.

Radial cutouts and curly elements complicate the work a little, but if desired, this task can be solved without problems. For example, choose a rectangle shape.

The drawings are not dogmas; they can be changed at your discretion.

The beam is at the bottom unless the bench is very long. The beam itself becomes a stiffening rib in such a situation. The dowel involves the use of both closed and open mounting, the last option is quite unusual. The material can be in any form. It is even possible to use options that are used to build wooden houses.

Video gallery

Photo gallery

To garden plot was quite comfortable, it should be properly equipped. An important component are garden benches. They can be made independently in different ways and from different materials.

Bench made of concrete slabs and boards with backrest

By looking at the drawings of the bench, you can find out the features of its structure. You can make such a design with your own hands relatively easily, quickly and without high financial costs.

Making a bench with a backrest with your own hands in step by step instructions described in great detail.

Assembly: initial stage

After preparatory work The time for wood processing is approaching. In order for a hand-made bench with a back to serve for a long time and decorate the area, the materials must be pre-treated.

The tree is covered antiseptic compounds and let it dry. After this you can start collecting backrests

On one of the two-meter boards, fifty centimeters are measured from the edges. At this level the edges of the beton slabs. From this mark another fifteen centimeters are measured towards the center of the board. This is where the first boards will be attached. From the resulting marks we measure seventeen and a half centimeters - the gap between the back boards. Next, we measure fifteen centimeters for two more boards. There should be a gap of five centimeters between them. All this can be seen in the drawing.

Wood glue is applied to fifteen centimeter sections. They are attached to boards, the length of which is sixty-five centimeters. Additionally, they are secured with self-tapping screws.

On top, between the boards of the back, pieces of seventeen and a half centimeters are glued. To ensure that the parts stick together well, they are clamped and held until the glue sets. After gluing is completed, the back is covered with an antiseptic.

All wooden parts can be covered varnish. This will give them additional stability and attractiveness.

Assembly of the main part

It is better to assemble the main part of the bench from both sides. Placed between the boards concrete plates, and in drilled holes insert M16 threaded rods fifty-five centimeters long. You will need four of them.

The rods are fastened with M16 nuts and washers. They are twisted simultaneously from different sides to make the bench level.

Simple DIY bench

You can make benches for your garden with your own hands quite quickly if you follow the instructions. Let's consider four options for such garden structures.

On drawings benches, all its features are indicated in detail. Making such a bench with your own hands is quite simple. The only difficult element is the concave seat.

The number of parts and their dimensions are indicated in the table.

We begin making a bench with our own hands from wood with blanks necessary details. Boards and beams are cut into pieces of the required length.

Making seat supports will be somewhat more difficult. You will need to mark the blanks. Two points are marked along the edges at a distance of seven and a half centimeters from bottom side, and in the center a point at a distance of four and a half centimeters. They are connected using a flexible plastic ruler and cut out jigsaw. The sections are processed with sandpaper.

The seat supports are attached to the two upper drawers. One on each edge and one in the middle. Next, screw in the supports, spaced from the outer ones by the width of the leg. All connections are made with self-tapping screws.

Boards are attached to the resulting base seats. It is advisable to deepen the screw caps.

Then attach legs. They are attached to the seat supports. The lower drawers help secure the legs.

The finished product is coated antiseptic and varnish.

Simple bench No. 2

To make such a garden bench with your own hands, you will need concrete flower girls and boards. Flower girls are required to create the base of the bench. Use two s rectangular base and two cubic ones.

To make the base stable, the flower boxes must be glued or connected from the inside with staples secured with self-tapping screws. The container is filled with a layer of drainage and soil. This increases their stability.

The seat for the bench is made of boards. To do this, they are cut into pieces of the required length. These blanks are laid so that there is a distance of half a centimeter between them. Then they are connected using transverse strips. The planks are placed in three places: at the edges and in the middle. Corners are attached to the slats. With their help, the seat will be secured to the flower girls.

DIY bench with backrest

Prepare the bench parts shown in the figure. They are being processed antiseptics before connecting.

Then the parts are assembled into supports. The corners are first rounded and chamfered. First, parts A and B are connected with a bolt, and then B, C and D are also connected using a bolt.

The inclination of the backrest is determined by part D, after which it is connected to part A. Similarly, but in a mirror image, another support is made.

After this, the back and seat are assembled. To do this, the supports are placed so that there is a distance of one meter and twenty centimeters between them. First, the front and rear strips are screwed to the supports, then all the rest, and finally the stops are screwed in.

On last stage The back of this bench is screwed on.

Bench No. 4Another option for a simple DIY bench. Its length is one hundred twenty centimeters. The height from the ground to the seat is fifty centimeters, the height of the backrest is also fifty centimeters.

The base is made from boards, the thickness of which is five centimeters and the width from ten to twelve. One of the legs continues and serves as a support for the back. The supports are connected using the “half-tree” method and secured with bolts.

The basis for the seat is a block secured with self-tapping screws. The short supports on the back of the bench are connected with a collet to increase stability. The seat and back are covered with boards of less thickness. The surface is painted or varnished.

A simple bench with a back for a summer cottage

The dimensions of the structure and wooden parts can be seen on drawings benches. If we consider how to make a bench with our own hands, then this option will be the most optimal in terms of the simplicity of the process and the result obtained.

It is better to purchase materials already cut to size. If this is not an option, then you need to cut them yourself.

The resulting blanks polished. The ends of the boards are processed with an electric planer.

The back legs of this simple DIY bench also support the backrest. To create the desired level of inclination, the workpieces are marked.

At a height of forty centimeters, mark the attachment point seats. Above, the board is cut at an angle of twenty degrees. The cuts on the two workpieces must be identical.

First they collect legs benches: the front ones are connected to the back ones using a beam. It is better to do this from above and below.

When the side parts are assembled, they can be connected to each other with seat boards. Screw the boards with self-tapping screws, leaving a distance of one or two centimeters.

To strengthen the structure and increase its stability, make the lower harness timber along the legs. Two boards are attached for the back.

Finish the work with finishing coated, which will protect the product from moisture and adverse conditions.

DIY pallet bench

Make a bench with your own hands from pallets It’s not difficult if you use your imagination. To do this you will need three or four of these wooden structures. Some will need to be cut to get additional details. The simplest DIY bench design is made from pallets, when two pallets are attached perpendicular to each other, creating a back and seat.

To prevent the design from becoming too bulky, it is better to cut the pallets according the right sizes. The elements are fastened with self-tapping screws. Add side parts to enhance strength and make legs. All this can be seen in the photo.

Since the material of the pallets is untreated and rough, it will be required first polish. This will allow you to avoid splinters.

The manufacture of a bench with your own hands from pallets is completed by coating it with varnish or paint.

Bench puzzle

You can make such a bench with your own hands if you have a wide board and cuttings for shovels. Curly seats are cut out of the board in the form of puzzle pieces. Legs made from cuttings for shovels are attached to them. The result is separate stools that quickly assemble into one long bench. All manufacturing stages are discussed in detail in step-by-step photos.

Benches from unnecessary chairs: two DIY options

First option

To create such a bench for your dacha with your own hands, you will need four old chair.

From the first two chairs remove parts from the front of the seat.

The remaining sawed off the front legs are slightly lower than the seat structure.

From the resulting parts you need take off old varnish or paint. To do this, apply to the parts special remedy, dissolving paint coatings. Then the softened layer can be removed with a spatula.

The racks should drill holes for dowels. Holes are required on the front and end sides.

The dowels are lubricated with glue and inserted into the drilled holes.

When the dowels are glued, you can assemble base benches. To make the structure durable, the parts are fastened with self-tapping screws. Surface of the structure sanded.

For seats benches choose a board that is suitable in size, saw off the excess.

If several narrower boards are used, they are glued together with wood glue. For a tight connection, they are clamped with clamps and wait for the glue to dry.

The finished seat is also glued to the base with wood glue. Heavy objects are placed on the board and clamped together with the base with clamps.

When the glue dries, close the seat masking tape And paint paint the remaining structural elements for wood.

The tape is removed and the seat is treated stain. Finally, the entire bench is varnished.

Second option

To make a second garden bench with your own hands from old furniture you will need two chairs. It is better if the back and hind legs are not separated.

Two identical chairs clean up all parts of the structure except the rear legs with the back.

They take bars five centimeters wide and three centimeters thick. Cut two parts equal in length to the width of the chairs, and two pieces of the same length as the finished bench. A rectangle is assembled from these four parts. It is secured to the backs of chairs with self-tapping screws.

Another frame is assembled in the same way. Several transverse strips are attached to it. This design is attached under the seat, makes the bench more reliable and acts as a shelf.

If the chairs have old covering, then remove it with sandpaper. After this, the surface is puttied special composition or coated with a primer. When the layer has dried, it must be sanded with fine-grained sandpaper. Finally, the structure is coated with paint.

The seat for the garden bench is made by hand from Chipboard or plywood. A rectangle is cut out of the selected material, which is half a centimeter larger than the base on each side. Then cut out a piece foam rubber with the same dimensions. From upholstery fabric cut out a rectangle. It should be five centimeters larger than the seat on each side.

Foam rubber is placed on a sheet of plywood and covered with fabric on top. The fabric is attached from the inside out to the furniture stapler.

The seat is attached to the base with a piano hinge.

Bench-swing

To make such a bench for your dacha with your own hands, you should prepare necessary materials. Manufacturing begins with creation basics designs. The seat bars are attached to the back bars at the selected angle.

Additional ones are installed along the seat ribs, providing rigidity.

Attached to the seat planks, drilling holes for fastening in the base bars. The same goes for the back.

Armrests are installed on both sides of the seat. They can be secured with bolts.

The resulting bench cover wood protection products and varnish. It is very important to paint everything as carefully as possible.

The bottom of the bench is reinforced with metal profile. Chains are attached to the profile on which the swing bench will be suspended. It is imperative to check the reliability of the beams on which the bench will be suspended.

Log bench

To make such a bench with your own hands from wood you will need chainsaw. The main material is a thick log one meter long.

Log mark, so that you get two slightly unequal parts. The smaller one will be used to make the backrest, and the larger one will be used to make the seat.

Chainsaw log sawed along the mark. The resulting irregularities are immediately cut off with the same saw.

The cut triangular piece is cut into pieces and inserted into the holes in the seat. The back is secured on top. The bench is almost ready. All that remains is to give it a more decorative look.

Can the seat be placed on legs. To do this, recesses are made in the lower part to install a pair of logs as legs.

Transformable bench

The design features of the transformer can be seen in the drawings of the bench. A transformer bench is made with your own hands from planed boards, which is sawn to the specified dimensions.

Sliced timber parts holes for fasteners are drilled.

At the table top, the boards located on the edge can be made wavy.

In material intended for countertops, drill holes with a diameter of twenty-two millimeters and a depth of three centimeters. Cuttings of the same diameter will be inserted into them.

The edges of parts and edges are processed and rounded.

All elements are assembled using screws and screws. Screws are needed with dimensions 6x70 and 6x90, screws - 8x80.

Wooden parts are painted stain.

The structural parts that will move are connected by hinges.

Parts of a round shape are placed between the boards of the tabletop. cuttings

Install a stop for backrests

A hand-made transformer bench is covered varnish.

Rocking bench

Making an original bench with a backrest with your own hands is not difficult if you have the tools and materials. First you need to consider the drawings of the bench, which contain a small number of parts.

The side parts according to the pattern are transferred to Europlywood three centimeters thick. They are cut out using a jigsaw and the ends are processed with a grinder.

To attach the connecting strips, markings are made. Then the holes are drilled. After assembling the frame, the slats are attached using self-tapping screws. The fastening points are sprayed, and the entire product is varnished.

Bench around a tree

The simplest version of such a bench is hexagonal The size depends on the size of the tree. Measurements are taken at the seat height. To the obtained result, add another margin of fifteen to twenty centimeters. If you divide the result by 1.75, you will get the length of the inner side.

To cut boards ten centimeters wide, they are laid in four rows with intervals of one centimeter.

The cutting location is marked immediately for all rows with an angle of thirty degrees. So cut out six sets of blanks.

Legs are used with a height of sixty to seventy centimeters. They are connected by cross members by drilling holes and using bolts and nuts.

The seat is installed so that the joints are located in the center of the ribs of the legs. The outer parts are screwed on first, and then the inner ones. In this way, the entire hexagonal structure around the tree is assembled.

Finally, the back is made and the apron is installed. The result is a DIY circular bench with a backrest.

The finished product is processed oil impregnation.

Bench made of curved branches

A bench made of curved branches will look original. It will require branches for the front part, two legs, a horizontal top and a pair of transverse branches.

Sawing branches so that they fit each other as accurately as possible. Next they are connected by metal corners.

The back part is made in the same way and connected to the front.

The finished product is placed on a flat surface and the seat is assembled.

Bench options

• Log bench which goes well with surrounding nature. It consists of half a log used for a seat and two short round logs, which are the legs.
  
• Beautiful wooden bench with a back and armrests, reminiscent of a sofa. Curved and cut elements make it more attractive, while leaving knots and irregularities gives the structure a natural look.
  
• Bench made of wood and metal. The base of the structure is metal. The wooden parts of the seat and back are attached to it. Thanks to the small thickness metal parts she looks light.
  
• The bench has a simple, classic shape. It is made of wooden, pretty wide boards. This width allows you to sit comfortably on the bench. Armrests make the design more complete.
  
• Original bench made of wood with figured details. This option is well suited for a site with a natural, rural design. Carved legs and armrests, a figured back - all this gives the product originality.
  
• Bench with backrest interesting shape . The curved parts gradually bend back, creating a unique design. The seat is slightly curved but has a more traditional appearance.
  
• Wooden complex- a table with two benches. The design looks traditional due to the material used. An original solution is the fastening of all components into a single structure.
  
• The bench is made of solid log . A single piece is cut out of it, combining the back and seat. The legs are attached to the bottom. The log required is quite large.
  
• Bench with storage box for toys. Outwardly it looks like an ordinary wooden bench-sofa, but under the seat there is a drawer in which you can put various things.
  
• A comfortable bench made of wood with a simple shape. The base is made in the form of a rectangular box. The back is also simple with a straight shape. The seat has soft cushions for additional comfort.
  
• Wooden bench located around a tree. It is made as if it consists of four benches, each of which has one armrest. The composition looks attractive and comfortable.
  
• A simple bench made of wide boards. It looks solid, but its dimensions are somewhat concealed due to the gaps between the boards and the light blue, in which it is painted.
  

Garden benches are the most popular small architectural forms. They can be made of any size and design, but in addition to their direct purpose, benches also serve decorative function. You can make a garden bench for yourself using our drawings and photographs.

How to make a bench from waste materials

The easiest way is to make a bench out of wood. This is a traditional material for garden furniture, affordable and easy to process. But even in this case, you can save money by choosing as the main material the one that literally lies under your feet.

The first option is trees, poles and stumps from your own site or a nearby forest plantation, in which sanitary felling is carried out.

Having carefully cut off a couple of medium-sized stumps, they can be placed on the base of the bench. Use poles to make a bottom crossbar for structural rigidity. And for sitting, loosen part of the trunk on the circular. If there is no equipment for longitudinal sawing, then you can take an unedged board 75 mm thick.

In this example, the bench is already more comfortable - in addition to the seat, it also has a backrest. The model is a little more complicated, since you will have to find a higher part of the trunk and process it in two steps - first make a profile cut with a “ledge”, and then split the workpiece into two halves.

And to assemble the next bench, you will need:

• two short logs of the same diameter for the base;
• two medium-thick poles for back support;
• one long log, sawn into two halves (for the seat and back).

In short logs, you need to choose a groove so that the long log fits into it. Then the seat is secured in the grooves, and each pole is fixed at two points - to the base and to the seat. For fastening, it is better to choose powerful self-tapping wood bolts.

Another budget material for a country bench - pallets ( wooden pallets). But not just any pallet is suitable for making garden furniture. Ideally, you need one from a good edged boards, the so-called Euro pallet, which can be identified by the EUR marking.

Basically, standard width The euro pallet is somewhat large for the seat - 80 cm. You can shorten it to 67 cm by cutting it along the contour of the central bar. But you don’t have to do this. Here are some examples simple designs With different options bases and seats:

1. A bench made of four pallets uncut to width. Three serve as the base, and the fourth serves as the back. You will have to remove some of the support bars from the pallet for the backrest, and ensure the rigidity of the bench using wooden slats.

2. In this case, four pallets are also used, but already trimmed. Three ropes woven with a braid are used to secure the backrest, and wallpaper nails are used for decoration.

3. This bench is made from just two pallets. One is whole, and the second is cut and, as it were, bent at an angle - it serves as both a seat and a backrest. The design is good for its mobility - there are small wheels as legs.

Perhaps the only inconvenience of using Euro pallets as source material- This standard sizes 80x120 cm. They to some extent limit the possibilities for creativity. The use of ordinary lumber (boards, beams and beams) allows you to make a garden bench to suit every taste.

Board and block

It’s worth saying right away that any bench drawing can be adjusted for specific conditions. The only limitation is that the thickness of the board and the cross-section of the beam are sufficient to provide load-bearing properties.

Below is a drawing of a bench, which is made of only three “paired” elements:

• seat and back;
• a short support (back leg) made of a trapezoid-shaped board;
• long support (front leg).

1- front leg; 2 - rear leg; 3 - seat; 4 - back; 5 - front view; 6 - side view

The result is a stable structure with a triangle at the base and two transverse stiffeners.

This is what this bench looks like in real life.

This drawing shows the bench in a more complex design. To make it, you need a 40x140 mm board (supports, back and seat), a 40x70 mm block (short bundles of supports) and a 20 mm board (long bundle between the sidewalls).

And this is the same design, but using a board and a block 75 mm thick. Small differences in the base and attachment of the ligaments are not fundamental.

In principle, there is only one condition - the boards in the seat are fastened with a small gap, sufficient to compensate for the expansion of the wood under high humidity.

Large forms

Wooden benches in a “large format” look original.

For example, this “fat” one unedged board across the entire width of the log. Covered with transparent varnish, it conveys the natural beauty of wood with all its color transitions.

From rounded logs you can build not only a cottage or a bathhouse, but also a garden bench like this.

And from timber you can assemble original chair, capable of serving not only under a canopy, but also on outdoors— removable pillows are easy to bring into the house in bad weather.

Stone and wood

Stone, like wood, also fits organically into the landscape suburban area. Certainly, flat slab It is practically not found in nature, but sawn stone can be used.

The next option is easier to implement - the bench is made of small blocks wild stone. And since such a surface is not only cold, but also uneven, you can’t do without pillows.

Pillows add comfort, but you have to constantly bring them in and out. That is why wood is used for seats on garden benches, regardless of the base material. Like this one original bench, at the base of which a gabion is used (a mesh cage filled with stone, crushed stone or pebbles).

Concrete is no less popular for making the base of a bench. But it’s difficult to make a form with a complex contour for pouring at once, but small formwork is simple. And even a “cold seam” when poured in two steps will not affect the strength of the structure (such as in this photo).

Another option artificial stone– hollow construction concrete blocks. It is enough to fasten them together with good masonry glue, and lay a beam in the cavity, and the bench is ready.

Metal and wood

The simplest benches in design metal frame use a square profile.

Can be welded from profile pipe two sidewalls in the form of the letter “H”, and a solid wooden seat will also serve as a “stiffening rib”.

The following example also uses solid wood as a stiffening element, but the supports are made in the form of a square with a cross member for attaching the seat.

And this is the simplest self-supporting structure from square profile, in which the strength and rigidity of the welded base is sufficient to make the seat from a wooden block.

The following photo shows a factory-made bench.

But if you have a pipe bender in your home workshop (and it’s easy to make one with your own hands), then bend two types of arches and a “wave” from round pipe Just. Then the metal blanks must be welded, plastic plugs must be placed on the legs (sold for any profile and pipe size) and the bars must be secured to the “wave”.

Return