Gadgets for the garage. Homemade garage gadgets

Absolutely anyone can make accessories for their garage with their own hands. With the help of such products, the owner of the premises will free up a lot of space, and tools and equipment will always be at hand.

A workbench is a necessary product in every garage

A homemade workbench should be in every garage. It does not take up much space and makes it possible to comfortably carry out repairs and make useful crafts. Typically a workbench is made from strong wooden planks that are attached to a thick wooden beam or profiled pipe. Often the workplace is made of steel blanks. They are quite easy to cut and fasten into one robust construction with help metal corners and universal self-tapping screws.

To make a workbench, as well as other machines for the garage, you need to draw an accurate design plan. At the same time, take into account the space that will be allocated for the product. It is best to place the structure next to shelves or racks. In the drawing, note the presence of drawers and shelves. You will store small fasteners and tools in them. You can also attach a compact vise to the tabletop. Having drawn up a plan, start making the workbench. First, we assemble the tabletop.

If you have small room, then there is no point in making a large homemade product for it. You can connect the boards together using good glue and metal ties. As a rule, the tabletop of a standard workbench consists of 5–10 identical boards. Next, we make special grooves measuring 2.5x2.5 cm on the tabletop. They are needed for stops. As soon as the glue on the product has dried, the surface must be planed. The result should be a perfectly smooth coating. The legs for the structure can be made from several bars measuring 80x10x10 cm.

We make grooves in the front legs into which the brackets will be inserted. In the future, the latter will be connected to the longitudinal beam of the tabletop. Then we assemble the base of the underframe. It consists of two frames, which are made from 5x10 cm boards. The base is attached to the support, after which the frames are cut into the legs of the workbench by 2.5 cm. At the end, we secure the components with bolts. Then you need to attach the back and side to the workbench supporting walls. For their manufacture, sheets of chipboard or centimeter plywood are taken.

The last step will be connecting the tabletop and the upper frame. To do this, you should use powerful bolts. Afterwards we apply drying oil to the surface of the workbench. As soon as it dries, we treat the surface with varnish. As a result of the work, you received a stable structure on which you can not only repair spare parts or make various crafts, but also store tools.

Making a rack - about a complex design in simple words

Every driver probably has a lot of large garage equipment that there is no place to store. Where can you find a place for them so that you can quickly find the right tool? The correct answer is on the rack. This design will allow you to organize free space and save a lot of time. Similar devices for the garage can be made of wood or metal. The second option is more reliable, but it is quite difficult to implement it yourself.

The first one is much easier to accomplish, however, in order for the structure to last for a long time, it is worth choosing strong wood species for work. Beech or oak are perfect for this. Boxes and shelves made from them can withstand significant loads. In principle, the norm for a rack is the ability to withstand a weight of 150–180 kg. In practice, only a few adhere to these recommendations. However, it is definitely worth remembering that the maximum weight of all tools on the rack should not exceed 300 kg. Otherwise, this design will become dangerous for the garage owner himself.

Making a rack with a complex design is very difficult. It requires significant effort, a lot of time and equipment. It is not much inferior to a simplified product, the manufacturing algorithm of which we will consider in more detail. So, the operating procedure is as follows:

1. 1. First you need to take a board 9 cm wide and cut it into pieces of different sizes. In the future, these parts will play the role of supports for the structure.
2. 2. For shelves you will need to take a thicker board. It must be cut into several identical parts.
3. 3. Next, take a board for the base of the rack and mark on it the points at which we will make spacers. They should be located at a distance of 3 cm from the edges of the base.
4. 4. Attach the upper spacer using superglue. We nail the top shelf to it. The same manipulations must be repeated with other spacers and shelves. The bottom expansion part should be attached last.
5. 5. Then you need to turn the assembled product over, tighten the base of the rack with spacers, using screws for this.

After the work done, your rack is almost ready. At the end, all you have to do is clean the surface of the rack sandpaper and treat it with oil varnish. It is best to apply the latter in 2 layers. Attach the structure to the wall with powerful anchor bolts, screwing in the fasteners under the upper and lower flanges of the structure.

Cyclonic vacuum cleaner and press - useful homemade products for those who like to tinker

The list of homemade machines and devices must include a press. This clamping device will become an indispensable assistant to every lover of home creativity. To make a press you will need hydraulic jack, metal platform bed and 4 profile pipes. Two of them should have a cross-section of 4x4 cm, and the rest - 6x6 cm. To make a press, we take two pipes with a smaller cross-section and attach them to the base of the product. At the very top, between these pipes, we weld another pipe with a larger cross-section.

Install the remaining pipe so that it can easily move along the previously installed guides. The device made in this way works on a very simple principle. To connect two products, they need to be placed on the base of the press and covered with a thick plywood sheet. The pipe with the jack installed must be lowered, and then the two short pipes must be turned. By making this simple movement, you will securely connect the two previously supplied products.

The second device is a cyclone vacuum cleaner, it will help you always keep your garage perfectly clean. To make it, prepare a plastic or metal container. Important nuance– the lid of the vessel must be tightly closed. Next, we make 2 small holes in the lid. The first should be located in the center, and the second close to the edge. The hole diameters and cross-sections of the hoses you use must be the same. We connect the pipes to the holes. The first will serve to collect garbage, and with the help of the second you will connect a regular vacuum cleaner

Install a plastic elbow into the inlet pipe. With its help, air will be sucked into the device, like a cyclone. Thanks to the presence of this elbow, the vacuum cleaner will be able to suck in not only dust, but also small stones, sawdust, lumps of dirt and other small debris. All this will remain in the container to which you connected the hoses. If you wish, you can not equip the vacuum cleaner with a knee. But in this case, you will not be able to remove garbage, only dust. In such a device, it is best to use a plastic container and narrow hoses. If you need a more powerful device, then you should make a vacuum cleaner from large hoses, an elbow and a steel container.

Device for making ropes - ropes from plastic bottles

When heated, plastic bottles shrink quickly. Thanks to this, we are able to make fairly strong ropes from them. With their help, the garage owner will be able to connect several different products that are used on the farm. To create the device you need to find two bolts with nuts and washers, a piece of thin board, an electric drill and stationery knife. After that, take two washers and place them in the middle of the board. The centers of the washers should be marked on the board with a marker. We drill holes at the resulting points.

Next, drill holes on the back of the board. This must be done to prevent rotation during operation of the device. The next step is to screw in the bolts. We are testing the device. We put several washers on the protruding ends of the bolts. The final thickness of the rope will depend on the number of bolts. Next, place a stationery knife or a small piece of it on top of the washers. We secure the device with additional washers screwed in until it stops. Next, the device must be fixed on the desktop using clamps.

Then we take a two-liter plastic bottle, cut off its bottom and cut a strip in the remaining part. We place the latter on the device so that it is located under the knife. Next, we take the strip with one hand and pull it, while holding the plastic container with the other hand. As a result, from one unnecessary 2-liter bottle you will get about 20 linear meters ropes.

How to make a viewing hole - detailed instructions for beginners

Whatever one may say, sooner or later the car has to be repaired. And so that the car owner does not have to crawl under the car and “squirm”, bending double, it is necessary to dig a hole in the garage floor for inspection and repair. First of all, those who want to do this need to mark the area of ​​the room where the car is parked. To do this, the area of ​​the garage is marked with chalk. When creating markup there are several things to consider: important factors. The length of the pit must correspond to the length of the car, and another 1 meter must be added to this value. The width should be such that it is comfortable for you to work. However, be careful - this value should not be greater than the distance between the wheels of the car.

The depth of the hole is calculated taking into account the height of the garage owner. Another 20 cm is added to this indicator.

“Having taken measurements”, start digging a hole. Once you've done this, think about the arrangement inside. First of all, this concerns the walls of the pit. For this purpose, bricks can be laid on the sides, building blocks or concrete. The thickness of the walls directly depends on the material. So, if you use ceramic bricks, then this figure should be equal to 20 cm. If you purchased cement, then the wall thickness should be 12 cm. If you want to make walls from blocks, then their thickness should not exceed 22 cm.

Do not forget that the walls of the pit will require hydrophobic impregnation. It will protect materials from moisture. Impregnation must be applied from the inside of the brick or blocks. To make entry and exit more comfortable, we make steps in the front part of the pit. It is best to use cement for this. You need to start from the lowest step, gradually rising higher. Each of the staircase elements must be the same. To achieve this, first measure the height of the rise and calculate the number of steps.

Shelves in the room - for storing loose fasteners and more

Sometimes the garage space does not allow you to make and install a large, spacious shelving unit. In this case, you can make shelves of different sizes. They will be attached directly to the walls at any height convenient for you. This will make it possible to save space on the floor of the room. First of all, you will need to determine where the shelves will be fixed. On the selected section of the wall we make approximate markings, dividing the area into equal squares. Dowels will be screwed into the corners of these squares to hold the shelves.

To screw in the fasteners, drill holes for them using a hammer drill. If possible, it is worth purchasing special dowels with hooks at the ends - they will provide better fixation of the products. Next, we take a thin board and attach hangers with eyes to it. When calculating the distance, be guided by the markings you made on the wall surface. To secure metal hangers, use reliable self-tapping screws. After that, all that remains is to make the shelves. We take several boards and cut them into equal parts - they will serve as bottoms for the products. Then we cut out the walls of the shelves from thicker boards. We nail or glue them to the bottoms. If desired, the products can be painted or varnished.

The final stage will be the installation of finished shelves in the designated places. When installing each of them, carefully ensure that the products stand level and move freely along the guides. If you want, you can glue turned wooden handles to the front walls of the drawers. It will be more convenient to use the shelves with them. Very interesting idea will be making shelves from plastic canisters.

If you have a sufficient number of these containers, and in the future you do not plan to use them for their intended purpose, then you can use them according to this principle. First, we cut holes in the outer walls of the canisters. At the same time, make sure that only the right or only the left wall of each container is cut off. Otherwise, the shelves will look inorganic. After cutting out the outer walls, clean the plastic from burrs. To do this, use a file. After this, all that remains is to install the shelves in place in the wall or use them as drawers in the shelving unit.

An ideal garage should organically combine the functions of a reliable shelter for a car and a well-equipped place for performing various repairs and other work. There are a number of useful recommendations for interior design garage, and you can make most of the necessary accessories yourself without spending money on their purchase.

Work on the interior arrangement of a garage involves the use of many different useful devices. Read the suggested instructions and your garage will become the most convenient and comfortable.

Usually in the garage you have to store not only the car, but also many tools and other accessories. To conveniently place all this, you need to equip the garage with racks, shelves, hooks and other similar devices.

The best option is a spacious rack. You can do it yourself. Remaining free place fill in convenient shelves. There is nothing complicated in making them either. You will receive more detailed instructions below.

Get to grips with your tools. Arrange them according to frequency of use. The items you use most often should be stored in the drawers closest to the workbench. Store heavy equipment on the lower shelves of the rack; allocate space near the ceiling for spare tires - you will need them least often.

Secure the brackets

These devices will help you conveniently store replacement tires. Place the brackets closer to the ceiling, so the wheels will not take up space. usable space. For tires, buy large bags, or better yet, special covers to protect them from dust.

He's a workbench. The structure can be easily assembled with your own hands from boards and bars. You can attach a vice and other tools needed in the garage to the table. It is more convenient when the workbench is installed next to shelves and racks.

Organize your lighting system wisely

You will need several lamps: above the place where the car hood is usually located, above the work table, in other important places in the garage. Ideally, the lighting system should be organized so that you can turn on all the lamps at the same time and each of them separately. An ordinary double switch will help you do this.

Install an outlet near your garage door and above your workbench.

Designate a place to store your work uniform. One shelf or at least a basic hook will be enough. Also provide a place to store work shoes and personal protective equipment.

Security questions

Substances such as gasoline, oil, etc. are stored in the garage. To store them, you need to allocate a separate cabinet or at least a shelf not far from the gate. Place a box of sand nearby and hang a fire extinguisher on the wall.

Each tool in the garage must have its own place, otherwise there will simply be no order in the room. For organization convenient storage things, assemble a homemade rack. Ready-made models are quite expensive, and do not always meet the needs of a particular person. Therefore, it is much more profitable and rational to make a rack “for yourself” right away.

Assemble the rack in such a way that it can withstand a load of at least 150 kg. In this case, the load on each individual section should not exceed 500 kg. The rack can be assembled from wood or metal. The design can be straight or angular.

As for wood, preference should be given to the most durable species such as oak, hornbeam, beech, etc. Everything before assembly wooden elements designs are processed antiseptic impregnation. Thanks to this treatment, the wood will be more resistant to moisture and various bacteria and will last much longer.

If possible, plan and sand all frame elements with high quality.

Make shelves from plywood or chipboard. DVL and OSB boards are also suitable. The main thing is that the plate has a thickness of at least 4 mm. The higher the expected load on the shelves, the thicker they should be.

To give the shelves a more presentable appearance, it is recommended to cover them with decorative film or paint them. Also, such processing will allow you to better get rid of contaminants in the future.

The simplest rack is made in several steps. Complete each of them in sequence. Various sizes will be given below. You can stick to them or change the dimensions at your discretion.

First step. Take a board 9 cm wide and cut it into several pieces different lengths: 30 cm, 27.5 cm and 18 cm. From these pieces you will make spacers.

Second step. Take a board 19 cm wide and cut it into the required number of 36 cm long sections. From these sections you will make shelves for your rack.

Third step. Mark on the board that serves as the base the places for attaching the spacers. It is recommended to install spacers at a distance of 2.5 cm from each edge of the base. Glue the top brace in place, then nail the top shelf to it with the pre-attached brace. Do similar manipulations with the remaining spacers and shelves. The lower strut is attached to last resort.

Fourth step. Turn the rack over and tighten the spacers to the base of the structure using screws.

Fifth step. Carefully sand all wooden surfaces and apply a double coat of oil varnish. If you wish, you can cover the shelves with decorative film or decorate them with other material at your discretion.

Sixth step. Attach the shelving unit to the wall using anchor screws. Place fasteners under the lower and upper shelves.

Using this scheme, you can assemble a rack from the required number of sections. To strengthen the structure, place between sections wooden blocks. This will help distribute loads evenly throughout the system.

If there is no space to install a full-fledged rack or, on the contrary, you have installed racks and there is little unoccupied space left, be sure to make several convenient and simple shelves for storing various accessories.

First step. Determine where to place the shelves. In accordance with this, set the required quantity and optimal sizes of products.

Second step. Prepare the required number of boards and fasteners in accordance with the plan drawn up at the previous stage.

Third step. Mark on the walls where the future shelves will be attached.

Fourth step. Armed with a hammer drill, prepare holes in the walls in accordance with the markings and screw dowels into them. It is best to use dowels with hooks - they will provide a more reliable fixation of the shelves.

Fifth step. Attach eye hangers to the board. When choosing a distance, refer to the markings on the wall. Use self-tapping screws to attach metal hangers. If you don't have them, you can get by with ordinary nails.

Metal shelves

Metal shelves for garage

Metal shelves

Sixth step. Fix the finished shelves in their intended places.

Remember: it is better to make several short shelves than one long one, which will break under the weight of the objects placed on it.

If you wish, you can do decorative finishing shelves, for example, cover them with film or paint them. Make sure the shelves hang level. A tool called a level will help you control this moment.

To make working in the garage as comfortable and productive as possible, assemble and install a workbench in a convenient place. With it you can repair both car parts and other household accessories. A homemade workbench has a big advantage over a ready-made factory-made model - you can make a table of the size that you need.

Workbench assembly kit

1. Boards.
2. Bars.
3. Fasteners.
4. Plane.
5. Ties.
6. Tool for wood processing.
7. Wood glue.
8. Sandpaper.
9. Drying oil.

First step. Consider the optimal design of your workbench. The main elements of such a product are the underframe and the tabletop. The design also includes one or more clamping devices.

Second step. Assemble the tabletop. The best option is a tabletop made of 20 boards measuring 200x10x5 cm. Prepare grooves for stops measuring 2.5x2.5 cm in the 5th and 16th boards. Place the grooves in 25 cm increments.

Use glue and metal ties to connect the boards. Before gluing, the surfaces of the boards must be planed.

Third step. Plan the dry tabletop thoroughly. It should be smooth flat surface. Over time, the wood will shrink. You need not to miss this moment and tighten the nuts on the ties in a timely manner.

Fourth step. Make the legs. To do this, use high-quality blocks measuring 80x10x10 cm. Make grooves for the brackets in the front supports. The brackets will later be connected to the longitudinal beam. This type of beam is commonly used in the construction of window frames.

Fifth step. Assemble the base of the table from two frames and fasten it to the supports. Assemble the frames from 10x5 cm boards. Use a tenon joint. The frames are directly cut into the table legs to a depth of 2.5 cm and bolted to them. Attach a sheet of plywood to the bottom frame. A sheet 1 cm thick will be enough.

Sixth step. Attach the side and back support walls to the table. To make the walls, use chipboard or plywood 1 cm thick. Build a convenient cabinet with a hinged door on the left of the table.

Seventh step. Connect the workbench top to the top frame using bolts. It is recommended to prepare the holes for the bolts in advance - this will make connections faster and easier. Tighten the bolts so that their heads are recessed into the wood.

Eighth step. Make a miter box. This device will help you in the future to cut workpieces at the required angles. The miter box is assembled from wooden strips 2 cm thick. Attach the finished miter box to the table using stoppers.

Ninth step. Process your homemade workbench drying oil and varnish. Let the paint dry and you can start using the table. If necessary, install a vice on it or, for example, circular saw. At this point, focus on your needs.

Video - DIY garage accessories

A garage press is assembled from scrap materials. No complex parts are needed; it is made practically from scrap metal scraps. We will need:

• Two sections of channel, 80 cm long each, with shelf dimensions of 50x30 cm.
• A piece of profile pipe with a diameter of 40 or 60 mm, 2.5 meters long.
• Iron plate 8 mm thick, dimensions 250x250 cm.
• Two corners, one of which is 300 mm long, with a cross-section of 50x50 mm, the second is 250 mm long, with a cross-section of 25x25 mm.
• The hydraulic jack is the main mechanism of the press.
• Two springs and bolts of different diameters for fastening. They are selected locally.

The base on which the press is located can be any plane, as long as it is strong and solid. Usually the press is installed on a workbench.

Homemade press on a workbench

First we make the side racks on which the entire mechanism rests. To do this, we take two sections of channel. From the bottom, for emphasis on each, corners are attached with the letter T. You can immediately make fastening points in them for subsequent installation on the base by drilling holes in four places on each edge. Then, using the same principle, a corner is attached to the upper part of the channel, and the pressing part of the press - a metal plate - is attached to it.

Now on the bottom of the support channels you need to make fastenings for the springs that return the press mechanism back. To do this, two holes are drilled and a bolt is screwed in from the inside. Then, using the same principle, the two upper fasteners are prepared on the underside of the pressure sheet.

Now all that remains is to make a stand for the improvised press. To do this, two profile pipes are cut, the length of which is slightly longer than the side supports from the channel. Connect them in such a way that they tightly grip the vertical posts of the press, but do not clamp them. A jack is installed under them, and holes are drilled in place for its fastening.

Improvised press on a stand

The homemade press is ready. For smooth movement, the side channel is lubricated with grease or oil. When the need arises to use it, the mechanism is installed on prepared mounts and the frame is tightened with bolts.

It’s easy to build an alarm system in the garage with your own hands; you don’t need any fancy “devices” for this. All that is needed is an old push-button telephone, a sealed contact, a spring switch, or better yet, a breaker and wires.

Do-it-yourself telephone alarm for the garage

The alarm is assembled as follows:

1. On your phone, you need to set up a one-click call and enter your number.
2. Then carefully disassemble it to connect the alarm wires.
3. If the “hang up” and “call” functions on the device are controlled by one key, then the first wire is soldered to it, and the second to the speed dial digit.
4. If these functions operate separately, then the third wire from the alarm breaker goes to the key.
5. If the button is used with two contacts, then they are soldered onto the call and dial function button.

Assembling a homemade garage alarm from a telephone

When making such homemade products, keep in mind that the breaker button will play a major role. It must be installed on the edge of the garage door between its opening and closing parts. At the same time, it should be positioned so that rain and snow do not fall on it. And the phone needs to be hidden in an inaccessible place, for example, in the far corner of the rack you built. To do this, you need to solder long wires to the contacts in advance. When closing the garage, the breaker button is pressed by the garage door leaf, and at this time the alarm is in standby mode. When the gate is broken or opened, the contact opens and the circuit signal is sent to the telephone, which will dial the entered number.

Remember that DIY projects like garage alarms require a certain amount of secrecy. You don’t need to tell everyone what a craftsman you are.

It is simply impossible without such structures as racks with shelves. You can put all the little things, spare parts, tools on them and attach a homemade press in disassembled form. To ensure that such homemade products fit into the garage space, first determine the location for their installation. They are usually constructed on one side of a wall or at the end of a room. The width must be calculated so that there is free access to the car and the open doors do not touch the pillars.

To install shelving you will need:

• block with a cross section of 50x50 mm,
• sheets of chipboard or OSB for the construction of shelves,
• iron corners and nails.

The base of the rack must be strong, because the considerable weight of the laid out tools presses on the shelves. Carry out all the calculations in advance and only then start working.

The basis of a homemade tool rack

The block is attached to the ceiling first. To do this, you will need self-tapping screws with plastic plugs. Using a hammer drill, holes are drilled along a pre-marked line in increments of 20–30 cm. Plugs are installed in them and the block is attached to them with self-tapping screws. Then the plumb line determines the installation location of the lower bar. Both the top and bottom bars should be on the same horizontal line to keep the shelving level and strong.

Now you need to install the vertical posts. For better stability of a rack with shelves, they need to be fastened every 40–50 cm. They are fixed with nails, which are driven in using the “oblique hammering” method or using iron corners. We measure the distance from the top bar to the bottom and according to the size we prepare the vertical elements of the shelving frame.

Now you need to install horizontal jumpers to support the shelves, but first you need to mark the places for their attachment. For this you will need a tape measure. From the floor, mark the distance to install the first row of shelves on the rack on each vertically installed block. Then measure the distance between each stand. We cut the bars to these sizes. Now they need to be secured. We insert one between the posts and secure it with screws from the end, two on each side. This way we install all the frame elements. Then, from the installed bars, the second row of shelves on the rack is marked with a tape measure. They are installed in the same way.

Installation of frame elements of a homemade rack

Before installation, it would be better to calculate in advance the number of shelves on the racks and assemble the frame according to the drawn-up drawing or diagram.

Having assembled the outer frame, all that remains is to secure the bars to the wall to install the shelves. On the wall, at the level of each row cross beams on the frame, a line is marked. Then building level The horizontal position is checked and the timber is attached along the entire length of the structure according to the markings.

All that remains is to make the shelves for the rack and install them. We measure the distance from the wall to the edge of the frame and from one vertical post to another. According to the obtained dimensions, we cut the chipboard sheet, install it in place and, for reliability, fix it on top with self-tapping screws. We do all the shelves in the same way.

Shelves usually don’t have doors; you can hang a dark fabric curtain along the entire length. That's all, the place to store the necessary things is ready. All that remains is to model a homemade workbench and it will be completed in the garage.

It is impossible to make homemade items in the garage without having a workbench at your disposal. First, its support is assembled from corners or a profile pipe. It is better to connect these parts by welding. But if this is not possible, then bolted fastening is allowed. But for this you will have to additionally mark the joints and drill holes. The convenient height of the finished workbench is 90 cm from the floor. This will make it more convenient to carry out work at the workbench. But for some it is better to repair while sitting, in which case the height of the workbench will be different. The dimensions and dimensions for each garage are different. And it’s better to decide on them before assembly.

Having assembled the base, we move on to making the tabletop for the workbench. Recommended thickness is 7–7.5 cm. Can be made from a single sheet of multilayer plywood 100 mm thick. If this is not possible, we will do it differently. Let's glue together a table top from several sheets of regular plywood. The standard thickness is 1 cm and in this case 7 pieces will be enough. Having decided in advance on the size of the workbench (its upper part, where the table top will be attached), we saw off the plywood along it. You can use PVA glue for connection, but better moment or BF. It must be applied to each sheet separately and after waiting for 3-5 minutes, connect all the sheets.

Making a workbench top from plywood

After this, the glued sheets must be laid on a flat place and pressed down on top with a heavy load; everything should remain in this state for 24 hours. In order not to cut each sheet of plywood to size, you can first glue them together, and then cut out the table top for the workbench from the prepared material.

Now you need to cut off an iron sheet for the top covering of the working surface of the workbench, on which all work will be carried out (metal 4–6 mm thick is required). For accuracy, it is better to place it on plywood and trace the outline with an awl or nail. Then cut the sheet with a jigsaw equipped with a metal file. You need to fasten the tabletop with bolts, having previously drilled holes in it and on the workbench. After assembling the workbench, you can make small shelves and cabinets with doors in its lower part. Any plywood or pieces of chipboard left over after making the racks will be suitable for this.

Iron sheet for workbench top cover

A variety of homemade products make the life and work process of a car enthusiast much easier. There is no need to look in the corners to see where everything is, all the details are in their place. A simple-to-assemble alarm system will reliably protect the garage from burglary or car theft.

For the rational use of space, communications and do-it-yourself garage accessories from scrap materials are used. It is necessary to use walls and an underground level in the process, place machines inside the room, and organize normal lighting.

Homemade gadgets for the garage

For comfortable operation of a room intended for car storage, you should adhere to certain recommendations:

• the tool must be as accessible as possible;
• storage spaces equipped with shelves/racks are much more convenient;
• workbenches, inspection pits, homemade machines and do-it-yourself garage accessories expand the capabilities of the car owner;
• the cellar allows you to save space;
• The productivity of work and minor repairs depends on the quality of lighting.

Organization of work space inside the garage

Depending on the dimensions of the building, the area occupied by equipment, fixtures, and communications should not be more than 10–20% of the size of the garage floor.

Storage areas, racks, workbenches

In 80% of cases, do-it-yourself garage fixtures are built to store accessories, tools, and vehicle equipment. It should be taken into account that the most bulky parts of the car are sets of winter/summer tires, depending on the season.

Tire storage rules

It is more convenient to store wheels on brackets of the following design:

• two triangular frames from a corner, connected by jumpers from any rolled metal;
• the triangles are attached to the wall, the wheels are installed perpendicular to the supporting structure, falling slightly between the jumpers.

Wheel storage brackets

This is the most economical option storing tires in the off-season. The most popular among car enthusiasts are straight and corner workbenches. The lower space is usually filled with shelves or drawers; sharpening machines and a vice are located on the tabletop.

Homemade garage workbench

An example of organizing a corner workplace

A folding workbench can be very convenient

Tree - universal material for both workbenches and shelving

It’s easier to build a wooden workbench yourself, but it has a shorter lifespan than its rolled metal counterpart, which needs to be welded. If in load-bearing walls During construction, corners for shelves were not included; it is easier to make racks from rolled metal or lumber.

Homemade garage shelving

Use for glass bottle racks

Built-in wardrobes are very compact

Original hanging shelves are suitable for storing long items

The design and arrangement of shelving inside each garage is too individual to follow general recommendations.

Inspection pit and cellar

A necessary accessory for a DIY garage is an inspection hole. Moreover, the owner does not have to carry out all the repairs himself. Underground communications can be used in the following cases:

• inspection of the chassis, steering, and brake systems before a long trip;
• oil change, which allows you to save money and does not take much time;
• minor repairs that can be carried out by the owner's qualifications.

Inspection hole in the garage

It is more convenient to make the entrance to the cellar from a hole, as this will allow you to concrete several steps instead of using an extension ladder.

Cellar under the garage

The main nuances of these designs are:

• swelling clay soils harmful to underground structures;
• therefore, all elements of the pit and cellar are insulated from the outside with expanded polystyrene;
• sand or crushed stone is used in the underlying layer before concreting and backfilling of the pit sinuses;
• Drains are laid along the perimeter of underground structures at the base level to collect and drain water.

The width of the pit should allow the driver to enter it without lighting.

Lighting and ventilation

Parallel circuits are more often used in garages lighting fixtures. One lamp allows you to use a specific area, several devices are turned on during a major renovation or a visit to the cellar. Minimum consumption electricity is provided by LED lamps. Daylighting devices have a great resource.

Cars use toxic, harmful fuels and lubricants, so do-it-yourself garage ventilation devices that allow you to create air exchange are becoming relevant. The influx is organized from below:

• garage - vents in the masonry, protected by bars;
• cellar - pipe from the garage or from the street.

Ventilation of the garage and cellar underneath

The hood is mounted under the ceiling of the cellar, the roof of the garage, or has the form of vents in the main walls at the highest points.

Related article:

Ventilation in the garage with your own hands. From this publication you will learn why garage ventilation is so important, what air exchange schemes exist, and installation nuances.

Other useful ideas

Useful accessories for the garage with your own hands can be made from used dishes, equipment, and materials left over from construction. For example, by gluing the lids of plastic cans horizontally/vertically, the owner receives convenient transparent containers for equipment or hardware, which are always at hand.

Device for storing small parts, tools, hardware

Interesting rack for storing screwdrivers made of PVC pipe

Homemade machines

From power tools you can assemble homemade machines and accessories for the garage:

• drilling - a drill fixed with clamps in a device that moves with a gear along a rack;

Drilling machine from a drill

• cutting - an angle grinder clamped in a similar way with equipment for metal or wood;

Angle grinder cutting machine

• wood lathe - the front headstock is made of a drill, the back headstock is made of a chuck, mounted on a frame made of a square pipe.

Drill lathe

The advantage of the machines is more accurate positioning of the equipment relative to the workpiece. The equipment turns out to be dismountable, the drill and angle grinder can be removed and used for their intended purpose.

Related article:

Metal lathe for the garage. Types of machines specifications, design, review of popular models in a special publication in our online magazine.

Hydropress

The simplest design of a hydraulic press is obtained from a car hydraulic jack. To press out/press in bearings and press/compress parts, you will need to build a frame and a removable movable stop. The frame consists of 4 channels welded to each other. At the top, the structure is reinforced with stiffening ribs (kerchiefs), and at the bottom, transverse corners are added, giving the frame stability.

Do-it-yourself hydraulic press from a jack

The stop is pulled in the normal position to the top crossbar of the frame by powerful springs. A hydraulic jack is installed between them, pressing the stop against the lower crossbar of the frame as necessary. The press force is regulated by a jack, the dimensions of the working area are selected depending on the size of the workpieces.

And finally, a few more examples of useful things for the garage.

Shelving near the ceiling

Pockets for storing cutting discs from disposable plates

Device for convenient use of threads and ropes

Trimmings PVC pipes - perfect material to create convenient storage spaces

Convenient pull-out racks for storing tools

Interesting DIY projects for the garage

Over time, a finished “motorhome” acquires a large number of tools. Conventional homemade products for the garage bring practical benefits without overpayments. Any machines made by yourself will not be inferior in quality to their factory counterparts. Let's look at some devices.

Knife sharpening device

Thus, the useful device receives a hole for the rod in the bolt. The rod is made by hand from thin wire. The carving is made taking into account the length of the sharpening bars.

The bar clamp can be created from:

• organic glass;
• ebonite;
• saw clamp.

The upper part of the plate acts as a clamp. Surface with two drilled holes applied to the bed. Then, closer to the knife, the general through hole. The thread is cut in the frame.

So, the homemade do-it-yourself device is almost ready. The second hole is made only on the plate away from the knife. Then cut a thread for the bolt (needed for tightening). A simple homemade mechanism for the garage allows you to sharpen knives on the go.

The artificial diamond stone is affordable and very wear-resistant.

Pulley for adjusting the speed and load on the machine motor

• metal;
• PCB;
• plywood (something between wood and metal).

One small and two larger circles are cut out in plywood with a jigsaw. The center of the molds must correspond to the diameter of the shaft. To avoid problems with further manipulations, the circles are glued together or seated on a screw and tightened with a nut.

Details useful device tightened with screws. Then the pulley should be processed with sandpaper or a file, placing the structure on the drill chuck. The finished machine fragment can be additionally polished.

1. Avoid vibration, make sure that the center of gravity is on the axis of rotation.
2. You can make a toothed pulley. Small channels are made at the central circle before all stages of assembly.
3. If necessary, a small pulley can be made from a thick piece of plywood (one circle). A groove is made in the mold and the part is placed on a screw. A narrow file is applied to the rotating circle.

Do-it-yourself vacuum molding of sheet plastic

• top and bottom frames;
• molding plastic;
• coupling bolts;
• perforated MDF;
• opening for the vacuum chamber;
• plywood base with a hole in the middle.

A hole is made in a piece of MDF or plywood (50 by 50 cm) for a PVC pipe with a three-inch diameter. A frame of beams (30 by 30 cm) is attached to the resulting base with glue. To achieve tightness, all cavities are sealed with sealant.

The edge of the water pipe is glued to the base with one end, and the other is connected to the vacuum cleaner hose. The entire structure stands on legs.

Certain holes are cut in the upper and lower frames to accommodate the vacuum chamber frame (firmly glued to the base). Along the perimeter of the frame, cavities for fastening elements are made at equal distances.

Types of thermoplastic plastic used:

DIY jigsaw

1. A steel square with a bolt soldered into it is made with your own hands as a file holder block.
2. The improved block is soldered to the previous saw holder.
3. Attention is paid to the desktop. Plywood is chosen as the base. The narrow table area is the same size as a jigsaw.
4. Furniture legs are mounted in the front plane of the table, and a small wooden stand is fixed to the rear plane of the working area.
5. To create leverage, use only hard wood.
6. The lever hole must be created slightly larger than the diameter of the pin (it regulates the spring tension).

Described homemade craft should stand on a “sole” that will not interfere with the work process. If necessary, a corner is cut in the area of ​​the base plate.

Do-it-yourself set of cutters for artistic turning

A semicircular grooved chisel-cutter is used for rough turning. The part is made from strips of tool steel.

A universal cutting device used for finishing parts. The tool is made from standard straight chisels.

Shaped cutters:

chisel scraper.

a tool based on a straight chisel with one-sided sharpening levels the surface of cylindrical workpieces;

a homemade device helps to fill threads and apply decorative marks to a wooden rod.

Cutting tools for soft wood (aspen, linden) have a smaller sharpening angle compared to the sharpening angle of a device for processing boxwood, oak, and birch.

Homemade extension cord with two sockets

The “branded” extension cord reel is made from two plywood disks that are bolted together. The fragments are separated by a duralumin tube and washers.

On one side of the reel, the bolts are recessed to ensure contact with the handle without injury. On the other side, two holes for sockets are drilled at a certain distance. Socket boxes are attached with screws.

Proper storage and use of the tool

Each pipe is attached to a plywood plate with self-tapping screws through a slot. To prevent the pipe fragment from becoming loose during operation, pieces of glazing beads are glued under the sides of the holder with PVA glue.

When it is necessary to hang the holder on the garage wall, the handle is inserted into the holder tube. The handle post fits tightly into the slot and is fixed. With this additional equipment, the reel is mounted on the ceiling or on the bottom of the shelves.

In order for the extension ram to rotate easily, a small handle is mounted on the edge of the device disk, which consists of tubular sections of various diameters. A larger diameter pipe is placed on a smaller hose and firmly fixed with a flat screw.

DIY crafts for the garage: the best ideas with photos

Useful homemade products for the garage with your own hands

Most often, during the initial arrangement, all the necessary furniture is ordered. But if you rent a room or don’t want to take money out of the family budget for this, then you can quite easily arrange it on your own, especially if you know how to hold it in your hands. basic tools. To help yourself and for inspiration, you can use the video from homemade products for the garage with your own hands (YouTube can please you with a variety of ideas), and you can also take into account tips on arrangement, which will be the basis for a successful layout.

If you look at the photo that shows the optimal set of useful furniture elements, you will notice useful nuances for yourself. First, the location of any storage system must be located at a certain distance from the walls. It is believed that there should be at least half a meter between the machine standing indoors and the rack for normal, comfortable work inside. If the shape of your car storage is more like a rectangle rather than a square (this happens quite often), then it is worth moving all the storage for tools and useful things to one area along the far wall opposite the door. This is where you can place not only a table or shelving unit, but even a carpentry or lathe with maximum convenience. It would be worth mentioning that all storage of your tools should be located inside the garage only if it is securely closed or is protected by a tightly closed gate in the country. Otherwise, it is better to place there only the most necessary things, preferably those that are not of particular value to robbers.

If you plan to install windows with your own hands in a separate room, which is located on the territory of your suburban area, then it is better to make them, so-called mansard type, that is, located in the roof, and choose a place just above such a working area. In summer and spring period This arrangement of windows will help you save on lighting, there will be enough sunlight for all types of work, and besides, you will also be able to ventilate the room, because ventilation cannot always cope properly, especially if you are going to work inside, like in a workshop.

If there is a total shortage of money or out of love for art, you can make an original storage system using old empty cans. Any motorist accumulates quite a lot of them over the course of a year, and if you ask your fellow neighbors, there will be enough for each compartment. interesting cabinet. Of course, there is nothing complicated here and to perform such homemade garage DIY video-lessons are not needed at all. You need to take plastic canister, wash it well so that no traces of its contents remain. Armed with metal scissors, a knife or other tool, we cut off the front cover of the canister, but so that the sides remain and the contents do not fall over the edge. To make the structure more stable, you can fix it on the back wall using self-tapping screws, but we will, of course, drive them not into the wall, but into wooden slats, which we attach to dowels.

Do-it-yourself garage crafts photo

The same option as shown in the photo can be used in homemade projects for the dacha, where you also often need to set up a workshop, and even less space is allocated for it than is left in the garage. For such a design, you will need to build a frame from wooden boards, and make notches along its upper and lower edges where the cells will be inserted. Most likely, the inspiration for this design was the classic hives that are used for breeding bees; the system here is exactly the same. The sheets that are inserted inside have a perforated surface and the presence of these small holes will allow you to screw nails inside, hang hooks to hang tools and useful devices as conveniently as possible so that they do not fly off when pulling out and retracting.

Exactly the same perforation can be included in a furniture set. Having such a complete set of everything necessary for home handyman, you can build many useful homemade products for the garage with your own hands, video with whom you are online. In popularity, such resources may soon overtake popular hand-made projects, because men, no less than women, want to make the space around them, their kingdom, beautiful, functional, and comfortable.

Interesting DIY crafts for the garage

We are used to either simply throwing away tires that are completely worn out, or making crafts from tires for the garden with our own hands. Having spent last winter's set on a swan or a flowerpot, this year you can easily allocate it to your loved one by making an entire furniture set. Frankly speaking, you will need not only car tires for this purpose, but also bicycle tires, because they can be used to construct the backrest, turning a stool into a chair.

Practice making such furniture and soon you will be able to replace yours. Coffee table on such a table in the living room with your own hands, crafts made from tires not only look beautiful, but can also become part of the original design concept.

A table and chairs are great; there will be somewhere to sit, but with the question of what to cook a delicious kebab on, our next idea will help. The fact is that an ordinary folding barbecue may not maintain the required temperature of the coals for a long time, and if you like to sit near the fire for a long time, you should make something larger. We will slightly modernize crafts made from wheels for the garden and present to your attention a barbecue made on the basis of a wheel rim. In order for the rim to maintain the set temperature well and not allow the coals to cool, it needs to be lined with bricks, but for maximum decorativeness of such a homemade product, it is better to file them a little using a grinder to fold them in a circle. The bottom must be filled with any available material, which does not support combustion, for example, fine crushed stone.

Homemade products for the garage with your own hands drawings

If you plan to spend quite a lot of time in your makeshift workshop, then among those you are interested in DIY DIY for the garage - heating, lighting, ventilation, that is, the arrangement of a fully comfortable stay inside for a long time. Some people prefer to install infrared heaters, but from the point of view of the cost of electricity this will not be a very rational option. A good option can be water heating, but it is best designed in garages that are located next to a residential building.

You can place solid fuel boilers of any design inside any type of garage, even make your own potbelly stove out of metal using welding machine. But do not forget that with this type of heating, the interior decoration must be made of non-combustible materials, and the ventilation must be done efficiently, even at the stage when we are building the roof with our own hands, in order to promptly remove all combustion products from the room.

DIY homemade machines for the garage

If you have a need for some specific work, then you can use special machines, for example, a pipe bending machine, which can be useful not only for motorists, but also for motorcycle owners.

DIY Garage Tools – Turn your camper into a home workshop!

Required tools and materials

Any car enthusiast can make a variety of garage accessories with his own hands, using inexpensive materials and the simplest tools. Such homemade crafts by a home craftsman turn a motorhome into a full-fledged workshop.

Garage workbench – it’s hard to live without it!

If you plan to do independent maintenance of your vehicle in the garage, as well as perform a variety of renovation work and make your own crafts, it will be difficult to do without a workbench. It is usually made from wooden planks that are mounted on solid foundation(profiled metal pipe or thick wooden beam).

It is also possible to make a desktop from metal blanks. They are easy to cut to the required sizes and assembled into one durable structure using steel corners and hardware (universal screws, screw connections, bolts, etc.) or using a welding machine.

Manufacturing of wooden or metal workbench always start by drawing up a detailed design drawing. You must correctly assess the workspace of your garage and fit the desktop into it as harmoniously as possible. It is advisable to provide shelves and drawers (pull-out) on the workbench. They will allow you to keep all kinds of tools at hand. It is recommended to install a small vice on the tabletop.

Making a metal workbench

If your garage has shelves or racks (or you want to mount them), experts advise installing a workbench next to them.

Then you will get an excellent work area where you can do any home creativity, producing original and useful homemade products for home.

1. Assemble the tabletop from boards suitable for you geometric parameters(for example, 200 by 10 by 5 cm), connecting wooden crafts between each other with metal ties and good glue. For a standard workbench suitable for any garage, it is enough to take 20 of these boards.
2. Make special grooves on the tabletop (on the 5th and 16th boards) for the stops. The parameters of the grooves are 2.5 by 2.5 cm.
3. After the glue has dried, the tabletop must be planed so that a perfectly flat working surface is obtained.
4. Use 80 x 10 x 10 cm bars to make legs for the workbench. Grooves should be provided in the front supports. You will insert brackets into them, which you will then connect to the beam (longitudinal).
5. Assemble the base of the table from two frames made of 10 x 5 cm boards and fix it to the support. The frames are cut into the legs of the workbench by about 2.5 cm, and then they are secured with bolts.
6. Attach the supporting walls (back and side) to the resulting structure. They can be made from centimeter plywood or chipboard sheets.

Now you need to connect the top frame to the tabletop. This operation can be carried out without problems using bolts. Don't forget to apply drying oil to the made wooden workbench and coat it with varnish. On such a table you will make any crafts with special pleasure!

A shelving unit is a must for the garage!

Over time, any vehicle owner’s motorhome turns into a kind of warehouse where a variety of items and tools are stored. They all need to find comfortable spot so that each device is easy to find. A self-made rack allows you to efficiently organize the storage of tools.

You can make such a structure from metal and wood. In the latter case, use solid wood - beech or oak. Shelves and drawers made from them can withstand quite serious loads. Rack by accepted standards must maintain a pressure of at least 150–160 kg. At the same time, it is not recommended to load home-made structures with things that generally weigh more than 500 kg.

Wooden shelving

Let's see how you can quickly make a garage shelving unit while spending a minimum of money on purchasing materials. The work flow diagram is as follows:

1. Take a board 9 cm wide and cut it into pieces of different sizes (18–30 cm). We will use these pieces as supports for the rack.
2. Make the shelves from a thicker board - 19 cm thick. To do this, you will need to cut it into pieces of the required length.
3. Mark the board for the base of the structure, indicating on it the locations of the spacers (they are usually spaced 2.5–3 cm from the edge of the base). Now you need to attach (it is advisable to use construction adhesive) the top spacer and nail the top shelf of the rack to it (with regular nails of suitable sizes). Then repeat these manipulations with other shelves and spacers. Lastly, the lower expansion element is attached.
4. Turn over the assembled structure, tighten the base of the rack with spacers using screws.

Storage facility various instruments and things are almost ready. You just need to sand the rack and then apply an oil varnish to the wood (it’s better to do two layers), and then attach the homemade structure to the wall with anchor screws. The places where the rack is attached to the wall are under the lowest and highest shelves.

Useful technical homemade products for the garage - a press and a cyclone vacuum cleaner

A homemade clamping device, which is sometimes impossible to do without in home-made projects, is very simple to make. You will need:

• hydraulic jack;
• metal platform bed;
• profile pipes with a cross section of 6x6 and 4x4 centimeters (two pieces of each will be required).

The press is done this way:

1. Attach two vertical guides (4 by 4 cm pipes) to the base of the structure.
2. Weld between them (at the very top) a piece of pipe 6 by 6 cm.
3. Install another 6 by 6 cm pipe so that it moves without difficulty along the mounted guides.

Homemade garage press

The use of such a technical homemade product is elementary - place the products you want to connect on the working surface of the press, cover them with a thick plywood sheet, lower the jumper pipe with the jack placed on it. You only need to apply pressure to the jack to glue two products or your own crafts together for centuries.

But with the help of the following homemade product - cyclonic vacuum cleaner, you can always point perfect order in the garage. It is made from thick plastic or (which is better) from a metal container. It must be sealed. Homemade manufacturing scheme for effective cleaning garbage in a motorhome is as follows:

1. Make two holes in the lid of the container. Place the first one at the edge, the second one in the central part. The diameters of the holes must correspond to the cross-sections of the hoses that you will connect to the device. One hose is connected to the hole from the edge, it is intended for collecting debris, the other is needed to connect a regular vacuum cleaner.
2. In the inlet pipe of the described homemade product you need to install a plastic elbow. It will ensure the process of swirling (cyclone) air in the tank. Due to this elbow, the effectiveness of such a homemade product increases, which easily and quickly absorbs small stones, lumps of dirt, sawdust and other solid contaminants. All of them will collect in the tank that you connected to the vacuum cleaner.

Device for making strong rope from plastic bottles

When heated, the material from which bottles are made mineral water and various drinks, is capable of shrinking. This gives us the opportunity to make excellent rope from such containers. With its help, you can very firmly connect various parts and assemblies in a motorhome and in the household in general.

Rope made from a plastic bottle

To make a device for making homemade cords, you need to stock up on two bolts with washers and nuts, metal washers, a piece of thin board or plywood, a utility blade and an electric drill. We make the device like this:

1. Place two washers in the middle of the board or plywood and mark their centers.
2. Drill holes in the marked centers with a drill.
3. Drill holes on the back side (this is a mandatory procedure to ensure that there are no twists or rotations when using the device).
4. Screw in the bolts.

The use of this craft is simple. You need to put several washers on the protruding areas of the bolts (their number determines the thickness of the rope being cut). Then you should place a utility knife on top of the washers (you can even use a piece of it) and strengthen the structure by installing several more washers and tightening the nuts until they stop. After that homemade device must be secured with clamps to garage workbench or other work surface.

Next we take plastic bottle volume of two liters, cut out the bottom, cut a strip (very small) of the required length and place our “blank” under the knife. You need to pull the tape with one hand, and hold the container being cut with the other. From one 2 liter bottle you will get about 25 linear meters of excellent rope with high shrink characteristics.

Under the tool - useful homemade products for the garage with your own hands

I live in the city of Veliky Novgorod, our plant produces containers, they produce drainage EP and EPP. For any city, this is very useful thing. Since these drainage units are needed for draining oils, oil, and fecal waste. I learned a lot on the site useful information, quality, dimensions, purpose of drainage containers. The NOVZERO company provides us with various containers for water towers and air collectors. You can order everything in Veliky Novgorod, there are numbers for orders. This company also provides a guarantee, services, such as equipment installation and more. Every city should have such factories and such products. novzero.com www.novzero.com/produktsiya/emkosti-ep-i-epp

#15 Homemade gadgets for the garage

DIY garage accessories

Homemade garage gadgets #tools

Homemade machines. DIY machines

Things #8 you can't live without in your garage, do it yourself

DIY hydraulic press

#15 Homemade gadgets for the garage

Under the tool - useful homemade products for the garage with your own hands

DIY garage accessories

DIY tools for the home workshop and garage

Homemade tools for the garage, ROLLING JACK

When creating, almost any owner strives to do something with his own hands, be it shelves for parts, a workbench, gates, ventilation or heating. We’ll talk about this in this article, namely how to create all these garage homemade products.

Lift gates made with my own hands, much better and more efficient than conventional gates with wings.

After all, everyone knows how much trouble these gates cause in winter, when ice accumulates on them, and there is a lot of snow on the area behind the gate. All this causes a lot of difficulties when moving the car out of the garage.

Therefore, such homemade products in the garage, such as overhead gates on one leaf, will be very convenient. The gates are equipped with a special device, thanks to which they rise. There is no need to apply much effort when lifting, since the total weight of the gate is compensated by 2 cylindrical springs.

The work is carried out thanks to a system of levers with springs and rollers that open along guides. It is thanks to this system that the sash rises. In this case, the compensating springs face outward, and the upper one goes inward (rolling along the guides).

Construction details: gate frame, opening mechanism, lifting leaf. The assembly mechanism is lightweight and convenient.

The gate frame is assembled quite simply with the help of 2 vertical bars and 1 horizontal one. The vertical bars have a length of 2300 mm and a cross-section of 120x80 mm. The horizontal beams have a length of 2750 mm and exactly the same cross-section. They are connected to each other thanks to angles and metal plates. The box is secured in the opening using metal pins with a diameter of 10x200 mm. IN concrete base the lower ends of the box posts are deepened by 20 mm.

The sash is made of a board panel (which is sheathed on the outside with sheet steel), a corner and a frame with ribs. The shield is attached to the frame using furniture bolts with metal strips. The frame is made of rolled steel and has dimensions of 2500×2100 mm.

Gate mechanism

When lifted, the upper part of the gate moves under the ceiling along guide rails. The rails consist of steel angles, 2100 mm long and 40 x 40 x 4 mm in size.

The fully manufactured rail is attached at one end to a steel plate for further attachment to the vertically located frame posts. At a distance of 120-150 mm, a section of channel is attached to the other end of the guides. The guides must be positioned strictly horizontally. This is achieved by placing a washer between the beam and the channel.

The gate lift is adjusted using a screw and spring tension. It is important to ensure that the sash is always in a stationary position. The gates are closed with special locks, which are located in the corners of the gate leaves. At the bottom and in the middle there is a handle with a height of approximately 20 mm.

In addition to garage doors, homemade products for the garage also include all kinds of shelves for storing tools. They can be either large, mounted in the far wall of the garage, or small, located on the sides of the room.

DIY garage shelves

The simplest and most basic shelves can be made using cables, which are sold in all kinds of hardware stores. They have high strength for hundreds and thousands of kilograms. Sold in a variety of sizes and diameters. Each shelf is supported by 4 such cables.

The next part that is needed when making shelves is a piece of metal or plastic tube. It is necessary to determine the distance between the shelves of the rack. They are fastened using special bushings with a locking bolt. The bolt is screwed into a threaded hole. As a result, the shelf rests on all 4 bushings (on each side).

Such shelves are very mobile and light, both in terms of weight and in terms of changing width. You can change the width to the required one at any time. However, it is worth remembering that they require good and durable ceilings.

For those shelves that will be attached to the walls, you can use wire about 4-6 mm thick, which is sold in any stores that sell metal in coils or cut pieces. A kind of “herringbone” is made along the width of the inter-ceiling space. Accordingly, to attach the shelves you need two identical “herringbones”. For one and the other side.

It is best to make these “Christmas trees” at the same time (for greater symmetry). You can use the shelf itself as a template. If you create these Christmas tree pendants with some reserve, then in the future it is possible to remove or insert additional shelves. Installation to the wall is carried out using self-tapping screws, staples or wood grouse.

Perhaps at first glance this design may seem fragile, but this is not entirely true. In fact, they are very strong and stable. Not a single element of such a triangle can be changed. The angles and lengths of the sides are quite strong and, moreover, elastic.

Making a workbench

In the garage, besides various works related to cars, many also perform plumbing, carpentry and other repair work. This is exactly what a workbench with a vice is for. Of course, it is much easier to use an industrial workbench, but a layout board is also used.

The sizes of workbenches and layout boards can be completely different. The height should be appropriate and convenient for the work being done. The best height is considered when the worker makes it at the level of the center of the palms of the lowered hand.

Making a workbench with your own hands is quite simple. Smooth boards with a thickness of 4-5 centimeters are used. The boards are connected to each other along the width. The main components of a workbench are considered to be a recess with a wedge, a stop, and holes with pegs.

The emphasis is needed to hold materials during work (planing). It is secured with screws or nails at some distance from the edge on the left side of the table. Looks like wooden plank about 10-12 centimeters wide, about 20 centimeters long and about 2 centimeters thick. The boards rest against their ends during planing.

The notch is necessary to clamp materials in a vertical position. In this case, all materials are secured using a wedge.

Holes with pegs are used for required emphasis when planing boards with a planer, cross-cutting material and some other processes. At a certain distance from the rear edge, holes are drilled along the entire length of the workbench. The pegs inserted into them are stops, so it is important that they are small height. Ideally, for products of different heights you need to have different sized pegs.

The workbench table itself is mounted on 4 legs, which are connected to each other by bars. Afterwards it is covered with drying oil to prevent drying out.

Room heater

DIY homemade products for the garage are not only all kinds of devices for equipment and repairs. These can also be devices for heating and ventilation. Let's consider an example of equipping a garage with a special stove, which is extremely necessary in winter time of the year.

It is known how often in winter it is necessary to warm up the transmission, and sometimes antifreeze (with severe frosts). The situation is greatly simplified when a special heating stove is used, which does not consume so much fuel and at the same time maintains the engine temperature at the desired level.

The operating principle of such a stove is based on the occurrence of chemical processes. Heat is released not due to fuel combustion, but due to the fact that fuel vapors on the surface of the heating element are oxidized by atmospheric oxygen.

Stove diagram

The stove consists of a burner, a fuel tank, and a fabric or asbestos wick. A heating element in the form of two metal meshes and a frame, which are impregnated with a catalyst, is placed in the burner. The wick supplies fuel from the tank to the burner itself. The upper part of this wick opens evenly under the mesh, and the lower part must be on the bottom of the tank.

When pouring fuel into the tank, you must ensure that it does not spill out into the outer part. Fuel should only be kept inside for safety reasons. After filling the fuel, the tank must be thoroughly wiped with a dry cloth.

The heater is started at a distance of 25 meters from the car. It is ignited according to the following principle. First, 50-100 ml of fuel is poured onto the grid of the heating element. Next it is ignited with a match. After the flame goes out, fuel vapors are sucked from the tank to the heated surface. In the presence of a catalyst under the influence of oxygen, they begin to oxidize. The temperature gradually rises and flameless combustion begins.

Often hot spots spread gradually, with a corresponding increase in temperature. Flameless combustion does not immediately cover the entire working area of ​​the burner. If you do not stop this process, it will continue until all the fuel runs out.

To make the heating element, long-fiber asbestos is used. For one hour, it is impregnated with a catalyst from a solution of platinum chloride or a cobalt-chromium solution. For 100 g of asbestos you need 1000 cubic centimeters of solution. The resulting mass is dried, tugged and calcined. The result is a dark and loose asbestos mixture. It is evenly scattered through wire mesh. And for a burner with an approximate surface area of ​​10 dm², the catalyst consumption is about 300 g.

Rules for operating the heater

Avoid contact with oil, dirt and water on the work surface. Following simple technology in the production of the heating element and proper operation will ensure the operation of the device for many years.

Return