Is it possible to cut tempered glass? We cut glass at home: with a glass cutter and simple scissors. Cut tempered glass at home.

You can get structures of different shapes from glass sheet, but to do this you need to learn how to cut it. If you have a glass cutter, this task can be easily completed. What if he is not there? How to cut glass without a glass cutter? In fact, there are several ways to cut material using various devices, which will be discussed below.

Preparing for work

Before you start working, you need to prepare the glass itself: rinse it with water, degrease it with gasoline. If it is mounted in a frame, you will have to adjust the product to the desired size. In this case, an additional 2 mm of material must be cut off on each side. This only applies wooden frames, since under atmospheric influences they are capable of contracting and expanding.

Before cutting the glass, you need to prepare the space. To work with it you will need a table or some kind of stand. This will make cutting easier and help the product break more evenly. If a master has to cut material for the first time, then he should practice on small pieces to understand the basic principles. Only then can you proceed to cutting large sheets.

Cutting with a glass cutter

Before using the tools at hand, you need to understand how to cut glass with a glass cutter. Cutting element placed perpendicular to the surface and strictly along the intended line. Lightly press the instrument and gently begin to move it towards you. If everything is done according to the rules, the sound of cutting glass will be heard and a thin white line will appear on the sheet. A creaking sound when cutting indicates that the tool is tilted incorrectly, is broken, or is pressed too hard.

After cutting with a glass cutter, the glass is placed on the edge of the table (or stool) so that the resulting line extends slightly beyond its edge. You need to hold the sheet with one hand and press on the hanging part with the other (it should fall off). If you can’t do it with your hands, you can gently tap with a hammer along the cut line. If necessary, the process is repeated from the very beginning.

We use scissors

Not very thick material can be cut with ordinary scissors. First you have to make markings. How to cut glass using this method? Need to put it in warm water and cut into pieces of the required size. If nothing works or the material begins to crumble, it means that you have found tempered glass (cutting features are indicated below). For cutting big piece You will need a bath or a large bowl of water.

The procedure is performed as follows: follow the markings with the tip of scissors, after which the unnecessary element is broken off. This method is suitable for sheets up to 3 mm thick and allows you to cut out shapes with straight contours. To make the work easier, a template is made from cardboard, which is glued to the workpiece with glue. You should know that the material will be more pliable under a large layer of water.

Twine, gasoline and lighter

The method described below will tell you how to cut glass evenly if you don’t have a glass cutter at hand. Everyone knows that the material is afraid of sudden temperature changes. This property can be used to cut it. For work you will need: twine with a maximum thickness of 2 mm (cotton only), lighter, gasoline (kerosene).

The glass sheet is placed on the table and a line along which it needs to be cut is marked with a marker. Measure and cut the twine so that it covers the entire length of the cut. After that, it is poured with gasoline and applied to the line on the glass. The twine must be set on fire so that it lights up along its entire length. When the thread goes out, it is watered cold water. As a result, the glass will crack at the location of the temperature difference. If the crack does not extend across the entire sheet, then you need to repeat the procedure and lightly tap along the cut line.

We work with a soldering iron

How to cut glass if you have a soldering iron at hand? The material is placed on a flat surface and, using a needle file, marks are made along the edges. A ruler is applied to it and touched with a soldering iron with a distance of 2-3 mm from it. Each place must be heated until the glass cracks. The soldering iron is passed over the entire cut - this way it will turn out quite even.

Break the glass with special tongs or place it on the edge of the table. The break will go exactly along the groove when sticking adhesive tape or wet newspaper along the cut. If the product needs to be inserted into the frame, you will have to cover the installation site with putty or strips of rubber. It is applied to the frame and covered with glazing beads, under which a rubber seal is placed.

Charcoal cutting

Below we will talk about how to properly cut glass using a charcoal pencil (you can do it yourself). It allows you to cut various shapes from the material. To make the tool you will need: charcoal(linden, birch) and gum arabic. The coal is ground into powder, gum arabic is added to it and a kind of dough is kneaded. Round sticks are made from the mass, after which they are thoroughly dried.

Before cutting, markings are made on the glass and the edges are filed with a file. The pencil is set on fire on one side and drawn along the line. The result is cracks through which the product breaks easily.

Cutting different types of glass

There should be no problems when cutting regular glass. They will help you cope with this task various instruments: from scissors to special glass cutters. But how to cut Below we will talk about exactly this. At home, you can also cut organic and corrugated glass.

Corrugated products are in great demand because they are inserted into doors and various interior structures. This material is easy to cut (like regular glass), so you can use the tools described above. It should be remembered that the cut must be made on the smooth side.

Making holes

Cutting a piece of glass sheet can be done easily and simply using ordinary tools. How to make a hole in it and what will be needed for this? It is necessary to stock up on wet fine sand, lead (tin) and a container for melting it, acetone, and a template. The template is a stick with a cone-shaped end, the diameter of which should match the size of the future hole.

To do the job you need:

• lay the glass on a flat surface;
• degrease the cut area and sprinkle it with sand so that you get a slide 50 mm high;
• take a template and make a hole in the top of the slide;
• melt lead in an aluminum or enamel bowl (can be heated on gas or with a blowtorch);
• pour hot lead in a thin stream into the sand funnel;
• wait 5-7 minutes and remove the sand around the hole;
• Use your finger to carefully check the cooling of the casting and remove it.

There will be a less-than-ideal hole under the casting. However, a handle, decorative elements, fasteners and other closing parts can be easily inserted into the resulting structure. Before cutting glass in this way, you need to practice on scraps of material so as not to ruin the whole canvas.

From what is described above it is clear that it is possible without special glass cutters. However, during the work you need to be careful and follow some rules so as not to damage the material and accidentally injure yourself.

Since glass is one of the most common building materials, it is often used for a variety of household needs. For example, to replace an accidentally broken window, as a decorative insert in interior door or greenhouse design. And then the need inevitably arises to cut out a piece from a large canvas the right size. A glass cutter is usually used for this. And at first glance it seems that this is not so difficult. However, craftsmen who first faced the question of how to cut glass with a glass cutter should keep in mind that this matter has its own subtleties and nuances.

How to properly cut glass with a glass cutter: general recommendations

Working with glass requires care and precision. It is imperative to take care of your own protection - wear thick gloves and large glasses so as not to be harmed by fragments and glass dust. It is more convenient to cut glass on a table; it should be covered with cloth or newspapers.

Those who do not know how to cut glass with a glass cutter should listen to the following recommendations from professionals:

• the sheet of material must first be cleaned and marked;
• The glass cutter must be positioned perpendicular to glass surface;
• you need to move it along the line smoothly - from the far end to yourself;
• the degree of pressure should be sufficient, but not excessive - the glass should crack slightly when cut;
• the pressure should be uniform along the entire length of the cut.

Before starting work, you should also choose a tool, because there are different types of glass cutters: roller and diamond.

How to cut glass correctly roller glass cutter?

This glass cutter has a metal roller with a diameter of slightly more than 6 mm. With this tool you can cut thin glass – no more than 4 mm thick. When working with a roller glass cutter, you should press it lightly so that a clearly visible white stripe remains behind. After all the lines have been drawn, you need to carefully tap them with the handle of a tool with reverse side glass, and then press hard on the edges and break the sheet.

How to cut glass correctly with a diamond glass cutter?

This glass cutter cuts thanks to special diamond edges. It is more convenient and durable, but also costs more than roller. Most often, the tool is used for cutting thick glass - up to 10 mm inclusive. A beginner should choose a model with a beveled edge. The cutting technology is generally similar to that described above, only the pressure on the glass during cutting should be slightly stronger.

Is it possible to cut tempered glass glass cutter?

Tempered or tempered glass is a strong but fragile material. So cut it regular glass cutter If it doesn’t work, it will definitely crumble. For this you need special machine with a diamond wheel, which is supplied with a special cooling compound.

How can you cut glass other than a glass cutter?

If a situation arises where you need to find glass sheet certain size, but you don’t have a glass cutter at hand, you can use other tools. For example, regular large tailor's scissors will do the job perfectly. You will also need a container with hot water. The glass should be prepared, markings should be applied to it, then lines should be drawn with scissors and water should be poured into them. Then break the glass by pressing on the edges. Of course, the cuts in this case may turn out uneven, so they need to be cleaned sandpaper or a file. Thick glass and plexiglass can be cut with a grinder saw. In addition, the acrylic sheet can be cut with a hacksaw with fine sharp teeth.

Glass products have always been extremely popular: frescoes, dishes and many other things created from scraps of this material have always amazed people with their grace and smooth lines. Looking at this magnificence, it seems that to create it you need to be a real professional who has extensive experience working with glass and a lot of necessary tools, and a mere “mortal” will never master this complex science. In fact, not everything is as sad as it seems at first glance, and anyone can learn how to cut glass at home.

Preparing glass for cutting

A lot depends on this stage, and the preparation process itself depends on what kind of glass you decide to use for cutting. New glass, purchased specifically for this purpose, can be simply wiped, and it is best to use old newspaper for this (this will avoid streaks and settling of small fibers). You will have to work with used material, spending much more effort. Firstly, it must be rinsed thoroughly using special means for washing glass. Secondly, degrease with a cloth soaked, for example, in kerosene and, finally, dry in indoors to avoid dust getting on the surface.

In addition, preparing glass also involves cutting it. As you know, you are unlikely to achieve completely waste-free production when working with glass, especially if you are planning to get a product that is not entirely correct. geometric shape. However, accurate calculation will reduce possible waste to a minimum. At this stage, more rational decision there will be a combination of the longer side of the glass with the long side of the workpiece. Please note that the resulting scraps should not be thrown away; they can be used in the future to create new products.

What tools to use?

Many of us are accustomed to thinking that glass can only be cut correctly and efficiently with a glass cutter. But what to do if you need to cut a piece of glass urgently, but you don’t have this tool at hand? There is another unusual one, but no less effective method, who helped our great-grandfathers get out of this situation. Such a tool is ordinary scissors, available to any owner. Let's look at each method in detail.

Option 1: glass cutter

The technology for cutting glass with a glass cutter is quite simple. To do this, you must comply certain conditions and choose the right glass cutter. Today, the choice of this tool is quite wide, which allows you to turn work into pleasure.

• Diamond glass cutter, time-tested and remains a leader in its field to this day. For home use glass cutters with a beveled edge are suitable cutting edge. This tool is designed to cut glass up to ten kilometers and is suitable for any thickness of the material used. From time to time, such a glass cutter needs to be sharpened on a special whetstone.
• Roller. As the name suggests, cutting part This glass cutter is made in the form of a roller made of a durable cobalt-tungsten alloy. The number of rollers can be from one to six.
• Oil. This tool works on the principle of a roller glass cutter, with the difference that a reservoir with oil is built into its handle, which is automatically supplied to the roller. Suitable for cutting thick glass.

To learn how to choose a good glass cutter, watch the video:

So, having dealt with the glass cutter, place the glass on a flat surface. Mark the glass and get to work. To make the task easier, you can use a ruler. It is worth considering the point that the line must be drawn the first time, otherwise a repeated attempt will lead to cracking of the surface. When cutting glass with a glass cutter, you need to apply equal force along the entire length of the line.

Option 2: ordinary scissors

Cutting glass with scissors like paper is not a fairy tale, but a completely everyday reality. For this purpose, you will need the scissors themselves (sewing scissors are best for this) and a tank of water (preferably hot). It is necessary to apply markings on the glass in advance, and then elementary physics comes into play: scissors create a microcrack, and the capillary effect completes the process. Of course, the result obtained will differ from that achieved with a glass cutter, but if necessary, this method can help out significantly.

Types of glass and features of work

Cutting ordinary glass does not pose any difficulties. Not only glass cutters, but also ordinary tailor’s scissors do an excellent job with this task. But what should those who have set themselves the task of obtaining a glass product with a more complex configuration do? To do this, it is worth familiarizing yourself with the properties of some glasses.

• Tempered glass products. In fact, it is impossible to cut tempered glass at home - it loses its properties. If you want to purchase an item with elements of this material, it is worth considering cutting it in the early stages. In addition, work with it must be carried out by professionals, since the hardening process of the resulting product can only be carried out under certain conditions.
• Fluted glass. This patterned glass is particularly popular in glazing doors or creating decorative elements interior Unlike tempered glass, you can cut such glass yourself. Working with it is not much different from working with ordinary glass, the only difference is that the cut is made from the smooth side. A roller glass cutter is best suited for this.
• Acrylic or organic glass - This transparent plastic, created on the basis of synthetic resins. No special tools are required to cut it. At home, a metal saw, cutter and other tools used for edge processing do an excellent job of this task. In addition, a regular stationery knife can handle glass whose thickness does not exceed 2 mm.

In any case, it is worth remembering that working with any glass must be accompanied by compliance with certain precautions. The presence of thick gloves and safety glasses are the main conditions for ensuring your own safety. It will not be superfluous to take care of the arrangement of the workplace. Since working with glass involves the presence of fragments, cover the work surface with any material that you won’t mind getting rid of. Feeling safe will allow you to achieve the best results.

(No ratings yet)

Discussion:

Pavel said:

For some reason, everyone writes about scissors as science fiction. About 25 years ago I read somewhere about this method... and tried it - I had to cut it out figured glass. In a basin of water, ordinary scissors, glass and off you go! – I didn’t expect it to be so simple! Of course, it didn’t cut, but pieces broke off, but exactly in the right place!..

Cutting tempered glass is a long and difficult procedure that requires careful preparation. It will not be possible to cut tempered glass in the same way as ordinary glass. The reason is its increased mechanical strength. This is due to the fact that at the end of the hardening process the crystal structure of the material changes. Many hardware stores sell such glass under the slogan “the most durable.” Therefore, attempts to cut such material in the same way as ordinary glass at home will not be successful - the material will collapse into pieces. a large number of small pieces. However, there are technologies for cutting such material at home.

Cutting tempered glass occurs after careful preparation of the material.

What kind of material is this?

Tempered glass is the name given to the most ordinary sheet glass (the manufacturing temperature and the tempering temperature in the production of ordinary glass are the same and equal to approximately 660 o C), which is cooled very quickly using blowing (cold air) on both sides of the finished sheet. Hardening (process) occurs due to very rapid cooling. Glass tempered in this way has high mechanical strength and resistance to high temperatures and increased safety (in case of destruction, glass breaks up into a large number of small and non-sharp pieces, which will not cause much harm to a person).

Tempered glass is used as showcases.

Residents former USSR This type of glass is familiar - it was called “Stalinist”. This is due to the fact that with such cooling, residual compressive stress appears in the crystal lattice of such glass. Thanks to its three positive qualities Such glasses have become widespread in construction industry, in the production of tableware, they are used as display windows in supermarkets, in various social institutions (schools, universities, hospitals, etc.), in the production of cars and other machines.

The main disadvantage of this material is its vulnerability to mechanical impacts at the ends. Even with a slight blow to the edge of the sheet, the glass breaks into a bunch of small fragments, and the entire sheet becomes unusable. However, even this drawback has found its application in everyday life - it is used if you want to create the effect of “ broken glass"(in the design of furniture or tableware).

Most often you can find tables or cabinets with “broken glass”. This effect is achieved by using 3 sheets at once: the top one is whole, the middle one is broken, the bottom one is whole.

Manufacturers of such sheet glass do not recommend (and some even prohibit) cutting such glass at home, since there is a high probability of damage to the sheet. How then does the cutting of tempered glass take place? living conditions?

How to cut tempered glass

Cutting tempered glass requires considerable effort and preparation. It should be noted right away that it is practically impossible to cut a large sheet of such material in domestic conditions. The only option is a laser machine, which will cut such a product quickly without damaging the structure of the material. In everyday life, this option is not feasible. The only acceptable option is to re-anneal the glass. In this case, you should pay Special attention on the glass cooling process. So, if the upper surface has already cooled down, the lower one may still be hot. But all this is described in more detail below.

What to cook

Safety glasses must be used when cutting glass.

In order to carry out such a complex operation at home, you will need:

1. Stove. It must be special and be able to heat up to 700 degrees Celsius. Some were lucky with such units - there were quite a lot of them in various research institutes, which were closed frequently in the 90s. Even now there is an option to purchase such a stove for laboratory work. If there is no special equipment, then you can turn to familiar blacksmiths or build your own brick oven in the image and likeness of blacksmiths.
2. Thermometer. It should have a high upper threshold of 700 degrees. If the furnace is laboratory, then it should have a built-in thermometer and temperature regulator.
3. Instruments for measuring, marking. These are rulers, squares, markers, etc.
4. Stones for grinding.
5. Wooden rods.
6. Diamond glass cutters.
7. Protective equipment (glasses, special clothing).
8. Powerful ventilation unit.
9. Strained glass.
10. Water.

Preparation and cutting process

In order to cut tempered glass, the first step is to reduce its strength and change its structure. For these purposes, annealing is used. It eliminates the stresses that were created by tempering this glass during its production.

Annealing is carried out using the technology described below:

Before cutting the glass, it must be marked.

1. First important stage- You need to soak the glass. This should be done in water at a constant temperature. The water temperature is gradually increased until the viscosity of the glass is equal to the viscosity in the furnace. This will require careful timing. The viscosity inside the oven is 1013 Poise. Different brands glass from different companies have different meanings viscosity, so there is no point in citing them. Also, the duration of the procedure directly depends on the size of the glass being soaked. Large sheets(window) are soaked for an average of 12-16 hours.
2. The next step is heating the glass in the furnace. The glass must be heated to its incandescent temperature. Depending on the manufacturer and brand, it can be different - from 470 to 680 degrees Celsius. It cannot be higher than 680. The required number can be found on the markings or in the accompanying documents for the glass. It is important to remember that American manufacturers indicate temperatures in Fahrenheit, so these values ​​should be converted to Celsius. You should not keep the glass in the oven for a long time; it is enough just to reach the required temperature.
3. When the glass has reached the required peak temperature, it is removed and cooled. Cooling must occur to temperatures that less temperature deformations (1014 Poise). In this case, it is necessary to ensure the slowest possible cooling. Next, the glass should cool to a temperature of 20-25 degrees Celsius. To do this, the glass is simply left in the room (or other room).
4. When glass became room temperature, cut lines should be marked on it using markers and rulers. After which cutting is carried out. It is made in the same way as ordinary glass - a glass cutter is used to make a “groove” along the cut line, and then the unwanted pieces are knocked off with light blows. For a more accurate cut, wooden rods of small diameter are placed under the “groove”. This is required if you need to make a very neat cut line.
5. When the glass is cut, you should take care of tempering it. At the first and second stages, the texture was “simplified” and tempered glass became the most common. Therefore, it is necessary to harden it again to give it its previous (initial) properties. To do this, steps 1 and 2 are completely repeated - the glass is prepared according to its viscosity, then heated in an oven to the temperature specified by the manufacturer.
6. Cooling during tempering differs significantly from cooling when imparting normal properties to tempered glass. To do this, pre-install open area ventilation unit(powerful), and ideally they lower the room temperature to 10 degrees Celsius (which does not eliminate the need for a fan). The glass is laid out on a pre-prepared machine (it should allow air access from both sides of the sheet) and the fan is turned on for intense airflow. Both sides of the sheet should be blown at the same time. After the workpiece has cooled to room temperature, the glass becomes ready for installation.

It is important to follow safety regulations and use personal protective equipment when performing all work.

After reading the glass cutting method described above, many people will prefer to abandon this procedure. And they will be 100% right. Because it is difficult, unreasonably expensive and dangerous to life and health. In addition, without experience, there is a high probability that the workpieces will deteriorate and this “experiment” will turn out to be very expensive. It is much cheaper, easier and safer to contact enterprises that have laser cutter or order glass of the required size from the manufacturer.

To process such a fragile material as glass, a special cutting tool. Of course, glass cutters greatly simplify the cutting process, but you can cope with their work with the help of other improvised objects. If you are faced with the need to cut glass and don’t have a glass cutter at hand, we will tell you what you can use to replace it.

How to cut glass without a glass cutter

Tools for cutting glass were not always as widespread as they are today. In the second half of the last century, people came up with their own ways to conquer this capricious material, without using a glass cutter. In fact, to cut non-tempered glass up to 8 mm thick, you can use many available items, you just need to have a little skill.

It is better to start listing items suitable for working with glass by identifying the types of impact on this material. The main methods include thermal, when glass is heated in a certain place, and physical, when it is cut by brute force. In industry, the waterjet cutting method is used, when glass is processed on expensive equipment under strong water pressure.

To cut glass thermal method, a small piece of twine and a flammable liquid like alcohol or acetone are enough; a soldering iron and a burning device can also be used as a cutter. To cut glass by physical force, you can use a file, a Pobedit drill, a nail, a thin diamond blade and even ordinary tailor's scissors. Of course, some of the listed items are difficult to get a good chip, but with the right skill, a quite suitable result can come out. Now, knowing how you can cut glass without a glass cutter, you can move on to the process itself.

How to cut glass without a glass cutter

Before you start detailed description glass cutting techniques, we would like to remind you about safety. Always wear work gloves and safety glasses while working to avoid cuts and small debris getting into your eyes. Be careful not to apply excessive pressure to the glass.

Burning thread

A very common method, mainly used for cutting glass bottles. Straight glass can also be cut using this method, but with minor nuances. All you need to make an even glass chip is a piece of wool thread, flammable liquid (alcohol, kerosene, etc.) and a container of cold water.

We soak the thread in flammable liquid and fix it on the glass along the cutting line. We set it on fire, wait for it to burn completely and immediately place it in cold water or pour it onto the heating area. The main thing is that the glass cools down as quickly as possible and bursts due to temperature changes. A characteristic click will signal the success of the work. If the glass does not crack, you can try repeating the operation.

Similar method It breaks bottles quite smoothly, but does not always work with large glass sizes. It is also very fire hazardous and requires a fire extinguisher or a container of water on hand, which is already required.

A very interesting, but rather slow method of thermal cutting of glass. It is more suitable for curly cutting, but it will also make a regular straight line without any problems. For this operation you will need a file and a heating element(soldering iron or burning machine).

Having marked the line of the future cut on the glass, take a file and make a small groove with it from the very edge. Having retreated 1-2 mm from it, we heat the place with a soldering iron until a microcrack forms between it and the mark. Next, we retreat from the crack itself to the same distance and gradually move towards the finish point. This takes a long time to cut glass, but you can get any shape. To speed up the process slightly, the glass can be periodically cooled by applying a damp cloth to it.

Scissors in water

A simple method of directional chipping of glass. Allows you to easily cut out round shapes, but is not suitable for creating straight lines. For such cutting, you will need ordinary scissors and a container of water, which will serve as a kind of lubricant. Maximum thickness glass should not exceed 4 mm.

The cutting process using this technique is extremely simple. We take a piece of glass to be processed, immerse it in water and break off small pieces from the edges with scissors. Water will prevent the glass from cracking, allowing you to make a controlled chip. In this way you can get oval and round shape.

Diamond blade

Not the best safe way cutting glass, requiring increased care and mandatory compliance with safety rules. It can easily break glass and throw a fragment in any direction. Otherwise, the method is quite effective and can cope with the task. For cutting, you will need a special tool (grinder, drill or drill) with a diamond disk 0.1 mm thick.

The cutting process itself is quite simple, but it requires some skill and a steady hand to guide the tool clearly along the line. We place the piece of glass to be processed on a flat place, then take a cutter and draw a line on the surface of the glass with a disk. The main thing is not to dive deep, but only lightly touch it so that a small hollow is formed, similar to a wide line from a glass cutter. Next, we simply break the glass into in the right place.

To reduce the likelihood of glass chipping and reduce the amount of glass dust while working, you can periodically water the cutting area with water.

File

Another way to cut glass at home without a glass cutter or expensive power tools. To work, you will need a file and a little experience in handling glass. Please note that the file must have corners, so a round one will not work.

To cut glass, it is enough to make several cuts on its surface with the corner of a file. You need to apply a little more pressure on the file than average so that the force is enough to form a clear groove, similar to the cut of a glass cutter. When the place of the chip is marked, we simply break the glass on the edge of the table or by placing a match under the place of the cut.

This method requires a certain skill, and if you are faced with cutting glass for the first time, we strongly recommend that you practice on small, unnecessary fragments before moving on to the main material.

Pobedit drill

If you know first-hand what glass cutting is, then we suggest considering another way to cut glass without a glass cutter. If you have some experience, one drill with a Pobedit tip may be sufficient for this operation. The main thing is that the drill is more or less new, with sharp corners on the head.

The process of cutting glass with a drill is in many ways similar to a conventional roller glass cutter. The differences include more high strength pressure, but otherwise all actions are standard. We lay the glass on a flat surface, mark the cutting line, apply a bar, and draw a line along it from top to bottom. Before cutting, rotate the tip so that the sharpest angle makes contact with the glass. Having received a clear line, we break the glass along the cutting line.

The method of cutting glass with a Pobedit drill requires skill and practical experience in handling this material. Beginning craftsmen have very little chance of making an accurate cut using this method, but with patience and straight hands, the desired result can be obtained.

How to cut a mirror without a glass cutter

The mirrors around us: in the car, bathroom or women's cosmetic bag, are in structure ordinary glass with a layer of metal applied to the back surface. Cutting glass with a mirror coating is practically no different from regular glass and can be done with a regular glass cutter or using the methods described above. When not at hand special tool, most effective device For cutting there will be a file or a diamond blade. Let's take a closer look at how to cut a mirror at home without a glass cutter, using improvised means.

The first step is to prepare the surface to be treated: wash, degrease and dry. The mirror must be clean, without stains or strong streaks. Otherwise, the cut line may be drawn and the chip will be uneven. Working surface where the cutting will be done should be smooth and not very hard. You can lay a thick cloth or a piece of linoleum on the table.

Having prepared the material and workplace, mark the line of the future cut on the mirror. It is better to draw straight lines using a ruler or staff with a height of at least 5 mm. To prevent the stop from slipping, you can glue a strip of electrical tape to its bottom. Next, take a file, grinder or other tool and make a cut along the marked line. More detailed process various methods cutting, described above.

When the cut is ready, all that remains is to break off the mirror in the right place. To do this, you can place a small object (match, pencil, nail) under the cut line and apply light pressure on both sides. You can chip the glass on the edge of the table or gently tap it from below with a small metal object(drill or spoon). If the glass does not break, you do not need to press very hard. It is better to make the second cut a couple of centimeters from the first.

Bottom line

The above methods have the right to life and give good result with skillful handling of glass. Perhaps, without experience in glass work, you will not be able to get an even chip the first time. Before you start processing the main material, we recommend that you first get your hands on unnecessary fragments. If you want to get a high-quality cut without much practice, it would be better to purchase a roller or oil glass cutter.

Save this page on your social media. network and return to it at a convenient time.

Return