Drawing of a hammock made of wooden slats. Hammock stand

A comfortable hammock will always be a favorite place to relax for the whole family. How nice it is to relax in the garden after working in the garden fresh air and swing in a comfortable hammock among tall trees. And you don’t have to buy it in a store, since such a piece of dacha exterior can be easily made with your own hands.

Types of hammocks and their features

The hammock first appeared among the Indians of the Caribbean islands. Since it was impossible to sleep on the ground, enterprising aborigines came up with such a device as a hammock. Seeing such a comfortable and safe bed, the Spaniards immediately adopted it, and later it was used by numerous residents different countries. Naturally, over time, the hammock has been significantly modified and modified, and now we can choose any hammock design at our discretion: fabric, wicker, wood, etc.

According to their design, hammocks can be:

Types of hammocks

The Brazilian hammock is a modification of the Mexican design and is intended for people who are accustomed to maximum comfort. It can be suspended on ropes if you use special straps and a rigid cross beam. The width of such a product reaches two meters. This is a rather expensive and difficult design to manufacture, since certain loads from hanging points are “distributed” along the fabric much more difficult than along the mesh, so installing such a product requires a large number of branches and drawstrings.
A Mexican hammock can be made of fabric or ropes. Has no hard parts. Since it consists of only a piece of fabric and a few strings for stretching, it can be carried with you in a bag, backpack or backpack. The disadvantage of such a product is the need for large quantities fabric (about 3 meters long and 1.5–2 meters wide). To hang it between the supports, a large distance is required. It cannot be made double, since you will need a fairly large piece of fabric that will roll up into a tight “cocoon”, which will make staying in it not entirely comfortable. You can stay in such a hammock for no more than two hours, since then your back starts to hurt and there can be no talk of comfort.
A Vietnamese or Malay hammock is made from a strong fishing net and hung on several support branches with varying degrees of load. Since this design was not very convenient, residents of Asian countries decided to supplement it with transverse bars - traverses. This is a comfortable bed that can easily be made into a double bed. You can stay in such a hammock for an unlimited amount of time without experiencing painful inconvenience.
The Brazilian sitting hammock is a smaller and simplified design that is mounted on a suspension trapezoidal shape. This hanging chair can be manufactured with a semi-rigid or fully rigid structure. That is, the hammock-chair can be completely wicker from natural or artificial rattan.

Photo gallery: hammocks of various types and designs

The wicker hammock chair has a stable wooden frame Hammock rocking on metal frame can be installed anywhere A wooden hammock chair will perfectly decorate country cottage area or children's corner You can make a bright and spectacular knitted hammock chair with your own hands Fabric hammocks are stronger than wicker ones A hanging fabric hammock with two fastenings can be taken with you on a hike. Frame hammocks can be various forms and any color Sleeping in a hammock is not only comfortable, but also useful Since the hammock is used in hot weather, it is very important that the material is environmentally friendly and has good air permeability It is easier to maintain balance in a hammock without cross bars If there is no suitable trees, hammocks can be placed in the gazebo Wicker hammocks will decorate your home and street

What is the best material to make a hammock from: the pros and cons of fabric and mesh

Regardless of the design and type of hammock, there are a few things you need to know general rules, which will help in the manufacture of a comfortable and durable product.

Fabric for making a hammock. Properly selected fabric will significantly extend the service life of the product and increase its strength characteristics. To make a hammock durable and reliable, you need to choose dense fabrics such as canvas, tarpaulin, teak, denim or camouflage. Materials from synthetic fibers are no less durable, but they do not allow air to pass through, so being in a hammock in the hot summer will not be entirely comfortable.
The fabric for a hammock should be as durable as possible, but at the same time allow air to pass through well.
Ropes or ropes for wicker products are also selected based on their strength, practicality and comfort. It is best to purchase products made from cotton threads. It is more convenient and easier to work with such ropes, they knit into knots and weaves more reliably and tightly, and are also pleasant to the body.
It is best to purchase ropes made from natural threads

Regardless of what you choose to make a hammock (fabric or ropes), you should not settle for cheap ones. synthetic materials. If we talk about what is better: fabric or woven rope mesh, then it all depends on the preferences of the owners of such a design. The fabric is denser and less breathable, so even in cool weather this hammock will be comfortable and cozy. The mesh product is ideal for hot and sweltering summers. Blown from all sides by even a small breeze, a wicker hammock will create a wonderful bed for relaxation.

If we talk about the complexity of making a hammock from fabric, then making it will be much easier and faster than weaving a fishing net yourself or learning the macrame technique. Therefore, you can simply buy a ready-made durable mesh, which will serve as the basis for making a rope hammock.

Preparing to make a hammock: drawings and diagrams

Before you begin, you need to know some rules for making a hammock structure.

We will sew a fabric hammock measuring 3x2.2 meters. For this we need a durable mattress teak, calico or camouflage fabric. To make the hammock comfortable and roomy, we focus on an adult (male). Therefore, we use fabric across the entire width.

We use it as a frame for a hammock wooden parts. It is best to purchase a 3.6 meter wide fabric, but you can take two 1.4 meter pieces and simply sew them together. If you take canvas, you need to take into account that on ordinary sewing machine It will be very difficult to sew such material.

To fasten the structure, we need a strong rope or clothesline made of cotton fibers.

Material calculation and tools for work

For the manufacture of various options we will need fabric hammocks certain materials and tools.

Fabric hammock with crossbars

Materials:

durable fabric - 3x2.2 m;
padding polyester - 50 cm;
sling - 5.2x3 cm;
nylon halyard - section 4 mm;
wooden block - section 4 mm;
sandpaper;
acrylic paint.

Tools:

metal ruler - meter;
chalk for marking fabric;
wood hacksaw;
chisel;
small brush;
scissors;
basting and regular needles;
centimeter;
sewing machine;
iron.

Ironed parts are thinner, easier to stitch and there is no need to hold the fabric with your hand.

Stages of making a hammock

On the wrong side of the material we draw two rectangles measuring 1.5x2 meters. Cut out the patterns and fold them front side to each other.
We retreat 1.5–2 cm from the edges and sew the short sides of the fabric on both sides. We turn the workpiece inside out. The lower part will serve as the back, and the upper part will serve as the face. Iron seam allowances on one side.
We sew the sling onto the long part of the part with a 5 cm indentation along the edges. The sling is laid along the back along the entire length, and on the front side at a distance of 35 cm from the seam. Next, we wrap the lower part of the workpiece onto the upper one, without cutting the sling.
We prepare 4 pieces of sling, 70 cm long. We sew them to the indicated fastening points, facing the back. Hem the edges to create holes for the crossbars.
We sew the long side sides of the product along the front side in increments of 30 cm from the edge. We cut out strips of padding polyester measuring 25x125 cm and put them in the prepared pockets. Then we fold, baste and stitch the edges so that we get some kind of rolls on the sides of the hammock on the long sides. In order to secure the padding polyester well, we stitch the pockets using the quilting method in several places.
We saw a wooden block into two equal parts. We mark approximately 2 cm from the two edges and make a notch about 1 cm in size. Use a chisel to remove excess shavings. Sandpaper we clean the sawn parts and paint the bars acrylic paint. Let it dry.
We retreat 5 cm from the two ends of the product and sew drawstrings to thread the crossbars into them. By threading the bars, we evenly assemble the base of the hammock on them.
We tie a nylon halyard to two crossbars, so that the knots are in the grooves.

Fabric hammock with eyelets

You can make a slightly different modification of a fabric hammock on grommets with wooden posts.

Materials and tools:

durable material - 2.7–3 m;
eyelets - 22 pcs;
tools for inserting them;
rope 35 m long, diameter 6 mm;
large metal rings;
electric drill and drill bit 12 mm;
beams 30x50 - their length should correspond to the width of the hammock;
sewing machine;
chalk for marking fabric;
scissors.

Manufacturing stages

We measure a piece of fabric and cut it 2.7 meters. We bend the edges by about 6 cm and stitch them on a typewriter. Then we iron them, fold them again and stitch them.
We mark with chalk on the fabric the width of the places where the eyelets are attached with the same spacing. We will get 11 pieces on each side.
In the marked places we cut out small holes and special tool We attach eyelets to them. Our hammock canvas is ready.
For spacers, we take 2 bars with holes drilled in them at the same distance as the eyelets on the hammock. They will keep the fabric from folding under the weight of people.
We pull the ropes through the holes.
We install the hammock straps. For this we make a special frame. But you don’t have to do it. To do this, we attach a metal ring to the hook, lay the hammock on the floor and secure it with a heavy press.
We make a spacer on the frame. We pass each sling through the grommet, and then through the hole in the spacer and the ring. We return the rope back. After completing all the work, we tie its ends. We braid the ring with the remaining ends of the slings. We do the same on the other side of the hammock. We hang it on supports.

All wooden elements We sand the structures and then coat them antiseptic. After this, they can be coated with varnish or paint.

Video: how to make a fabric hammock

Hammock swing

Such a small hammock for sitting can be easily made from a piece of fabric and a children's metal hoop (hula hoop).

Materials and tools:

durable fabric - 3x1.5 m;
hoop with a diameter of 90 cm;
padding polyester - 3x1.5 m;
durable grosgrain ribbon - 8 m;
sewing machine;
scissors;

Stages of work

We cut out two equal squares from fabric, measuring 1.5 x 1.5 meters.
We fold each one four times.
To make a circle out of it, draw a circle from the central corner with a radius of 65 cm and cut it out. We also do the second circle.
We mark the holes for the slings: fold the circle in four and iron it so that the folds are guidelines. The first pair of lines will be located relative to the bend at an angle of 45 0, the second - 30 0.
We also cut out the padding polyester.
To make identical slits on both circles, connect the pieces of fabric and pin them together
We lay the padding polyester between the two parts of the material.
We sew two identical covers on a machine. Then we sew them together, placing between them metal hoop.
We tie a grosgrain ribbon to the hoop in four places, cutting it into 4 equal parts.
The ribbon can be stitched or simply tied with a sea knot
We tie the free ends to a thick tree trunk or other frame at the required height.

We have created a comfortable and small hammock that does not require several support posts.

Video: how to make a hammock chair

Wicker hammocks have been known for a very long time, since in our country they were used everywhere, unlike fabric ones. For the most part, their base resembles an ordinary fishing or volleyball net, which is suspended between two trees.

Consider a hammock 2.5 meters long and 90 cm wide.

Materials and tools:

two wooden slats thickness - 1.5 m;
ropes or thick rope 170 meters - diameter 8 mm;
scissors;
electric drill and drill bit;
brush;
varnish or paint;
antiseptic;
metal rings - 2 pcs.

Weaving stages

We drill holes in the planks in increments of 4–5 cm.
We cut off 20 meters of rope, which will be used for fasteners. And we cut 150 meters into equal parts of 6 meters.
We fasten each rope with a loop and tie a knot on the bar.
We choose any weaving pattern with a cell size of at least 7 cm.
Having finished weaving, we attach the ends of the rope with knots to the second plank and make fasteners for the two planks. For this we use metal rings.
The ropes are secured to a wooden plank using loops and knots
We check the strength of the product and attach it to the supports.

Video: how to make a wicker hammock

How to hang a hammock

In order to hang such a hammock on two trees, it is necessary to stuff special support bars onto the trunks. They will prevent the halyard from sliding down.

But it is best to use metal or wooden poles, driven at a certain distance from each other. Special hooks must be welded to the pillars at a height of about 1.5 meters. If this wooden supports, then you can make special hoops with hooks.

Wooden frame for hammock

You can make your own wooden support frame for a portable hammock. To make such a design we will need:

wooden beam - 80x80 mm;
board - 100x30 mm;
studs, M10 bolts and nuts;
hooks for hanging a hammock;
sander;
electric circular saw;
electric drill;
keys;
paint or varnish;
antiseptics.

Assembly steps

We will make the lower support from two 3-meter bars and two 1.5-meter cross bars. Two side mounting beams are made of 2-meter timber and two 1.45-meter supports.

First we make the jibs. This is the side part of the stand on which we will hang the hammock using hooks. To do this, we fasten the beam and the stop together and saw it off at the bottom so that we get a vertical, but strong and stable part with a camber at the upper points of at least 4 meters.
The finished structure must withstand not only the vertical load created by the weight of a person, but also the overturning load
We install and fasten the side elements between 2 longitudinal bars. They should be in a mirror image of each other.
The width of the legs must be more than 1 m
We make the crossbar from two boards, 1.3 and 1.5 meters, and place them one on top of the other to ensure maximum stability for our structure. At the end, we fasten the longitudinal bars with transverse strips at a distance of 60 cm from each end.
To assemble the structure, you can use bolts or screws
We sand all the wooden parts with a sander, cover them with an antiseptic and let them dry. Then we cover it with paint or varnish.

Second frame option

The second design is more convenient and requires the same materials and tools as the first option.

In this case, we make the jib in a slightly different way, and also add a handle with which you can easily rise from the hammock.

Metal structure

Using the same principle, if desired, you can weld a metal support for a hammock from profile pipes square or round.

Video: metal hammock stand

If you stick to correct technique making a hammock, you will get a comfortable product where you can relax on hot summer days. A fabric or wicker hammock is a great option that will replace a bulky expensive one. garden furniture, and thanks to their mobility, such a structure can be hung in any convenient location on a personal plot.

Singletracks.com

This hammock can be made from ordinary cheap lining fabric, tarpaulin, linen, cotton, burlap - or anything. It looks simple, but it can be assembled in literally minutes.

What do you need

2 thick strong ropes 3–4 m long.

How to do

Fold the fabric in half lengthwise, fold the edge like an accordion and make a small loop out of it. Thread a rope through it and tie knots as shown in the video. Tie the second rope to the other edge of the fabric in the same way.

You can first prepare a hammock to which the ropes will be tied, or you can first tie the ropes to the support and then to the hammock. The knot described below is suitable for both methods. Just choose the one that is more convenient for you.

Wrap the rope around a tree, pole or other support. Make a small loop at the long end of the rope to which the hammock is attached. Thread the same side of the rope into it and tighten it. Thread the other end of the rope into the resulting loop and tighten again.

Carabiners will make the design more convenient and mobile.

What do you need

2 carbines;
2 thick strong ropes 0.5 m long;
a rectangular piece of fabric (approximately 3 × 1.5 m or less);
2 thick strong ropes 3–4 m long or 2 lashing straps 1–1.5 m long with loops at the ends.

How to do

Attach a carabiner to the middle of a short rope. Fold the fabric in half lengthwise, fold the edge like an accordion and make a small loop out of it. Thread the fastened carabiner into it and tie a knot, as shown in the video. Tie the carabiner to the other end of the fabric in the same way.

You can attach carabiners to a rope or to tension straps.

Tie the rope to the support in the same way as in the previous method. Thread the long end of the rope into the carabiner and pull it out. Wrap the extended part around the stretched rope four times and tie a knot as shown in the video.

The advantage of this knot is that it allows you to adjust the height of the hammock. The knot moves freely along the rope, but remains motionless when tensioned.

If using a strap, wrap it around the support, thread one end of the strap into the loop at the other end and tighten. Attach the carabiner to the loop on the long side of the belt.

bonniechristine.com

A simple option for those who don't want to bother with knots.

What do you need

a rectangular piece of fabric (about 2 × 1 m or more);
threads;
needle or sewing machine;
2 thick strong ropes 4–5 m long.

How to do

Fold the fabric on both narrow sides by 10–15 cm and sew. If possible, it is better to use sewing machine. The seams must be very strong.

outsidemom.com

Thread the ropes into the resulting loops and pull the fabric in the middle. Then tie the ropes to the supports with strong knots.

Laconic, convenient and quite simple design.

What do you need

a rectangular piece of fabric (approximately 2.5 × 1 m or more);
threads;
needle or sewing machine;
scissors;
32–36 large eyelets;
drill;
2 metal rings;
2 strong ropes 10–15 m long;
2 carbines - optional;
2 strong ropes 3–4 m long or 2 lashing straps 1–1.5 m long with loops at the ends.

How to do

Fold the fabric on both narrow sides by 5–10 cm and sew by hand or by machine. Make holes for eyelets at the same distance on these folds and secure them to the fabric.

littledogvintage.blogspot.com

Using a drill or other tool, make holes on the slats at the same distance as between the grommets.

Thread the rope into the metal ring and leave an end of 30–40 cm. Thread the long end into the first hole in the rail, then into the grommet with outside. From the wrong side of the hammock, thread the rope through the next eyelet, through the rail and again into the metal ring.

From the grommet you can thread the rope into the same hole on the rail through which it passed before. This method will provide an even stronger attachment. But to do this you need to take a longer rope and make wider holes in the slats.

littledogvintage.blogspot.com

Secure the remaining ends of the rope to the ring with strong knots. Make the same design at the other end of the hammock.

You can attach carabiners to the metal rings and hang the hammock from the supports as shown in the previous methods. You can also thread other strong ropes through the rings and tie them to the supports.

This option is more complicated, but such a hammock will become a real decoration of the garden plot.

What do you need

a rectangular piece of fabric (approximately 2 × 1 m);
30 not too thick ropes 50 cm long - optional;
stationery pins - optional;
threads;
needle or sewing machine;
14 beads - optional;
scissors;
2 wooden slats along the width of the fabric for the hammock;
24 small nails;
hammer;
2 metal rings;
2 strong ropes 15 m long;
2 carbines;
2 tie straps 1–1.5 m long with loops at the ends.

How to do

You can decorate the hammock in advance if you want it to look more interesting. Fold the long edges of the fabric a couple of centimeters, place the ropes vertically at equal distances and pin them together for security. Then sew the fabric along with the ropes and weave them into a pattern, as shown in the video. You can add beads for beauty.

On the narrow sides of the fabric, make 5cm long cuts approximately 8cm apart. In the middle of each slats, nail 12 nails at a distance of 3-4 cm. Place a ring 60 cm from the slats, thread ropes through it and weave a pattern, as shown in the video.

You will get two parts from rings and ropes. To attach them to the hammock, thread each loop of rope under the slits on the narrow sides of the fabric. Fold them over, pin them and sew them. Then hang the hammock using carabiners and straps.

Hammock using macrame technique

With wicker elements you can not only decorate a product and give it strength, but also make a hammock out of them from scratch.

What do you need

drill;
2 wooden slats 1 m long;
10 braided cords 9–10 m long;
2 metal rings;
2 carbines - optional;
2 tie-down straps 1–1.5 m long with loops at the ends or 2 strong ropes 3–4 m long.

How to do

Using a drill or other tool, make 20 holes in each rail at the same distance from each other.

Take one cord, fold it in half, thread it into a ring and tie a knot. Tie all other cords to the ring in the same way.

For convenience, hang the ring on a hook. Thread each cord through the holes on the rail. The distance between the ring and the rail should be about 20 cm. Then weave the pattern as shown in the video.

Finally, thread the cords through the holes of the second rail and tie to another ring. You can tie such a hammock using carabiners, belts or ropes, as in the instructions for fabric hammocks.

By the way, if you have absolutely nothing to tie the hammock to, you can make the supports yourself. For example, a massive wooden stand that resembles a boat:

Or a simple support of two beams:

minartanddoori.com

Perhaps the most unusual way do cozy place for relax. A hammock chair will not take up much space, so it can be hung not only in the garden, but even on the veranda or balcony.

What do you need

padding polyester;
scissors;
1 metal hoop with a diameter of 95–100 cm;
threads;
1 strip of fabric 3 m long and 20 cm wide;
needle;
stationery pins;
square piece of fabric (approximately 1.5 x 1.5 m);
4 tie-down straps, approximately 3 m long.

How to do

Cut several strips of padding polyester approximately 20 cm wide. It is necessary to make it more comfortable to sit in the hammock. Wrap the padding polyester around the hoop and tie with thread.

Then wrap a strip of fabric around the hoop and sew it so that the padding polyester is not visible. For convenience, secure the fabric with pins.

Place the hoop in the middle big piece fabric and cut a circle, the diameter of which should be 20–25 cm larger than the diameter of the hoop. Cut small symmetrical notches on the fabric blank on four sides. They are needed to provide a place to hang a hammock.

The hoop should be located exactly in the center of the fabric circle. Pull it lightly under the hoop, bend it and sew it very firmly to the hoop.

In those places where there were notches in the fabric, the hoop will be visible. Thread a belt through this hole and sew it up so that a loop is formed around the hoop. Sew three more belts in the same way.

Tie the straps to the supports so that the hammock hangs at an angle.

This chair will appeal to both adults and children.

What do you need

drill;
nails or screws;
hammer or screwdriver;
a rectangular piece of fabric (sizes will be stated in the description);
threads;
needle or sewing machine;

How to do

Using a drill, make holes in two thick slats on both sides at a distance of approximately 9 cm from the ends of the slats. The diameter of the holes should be such that thin slats can be inserted into them.

After 5 cm from these holes, make another hole of a slightly smaller diameter. The rope will be inserted there. Insert thin slats into wide holes on thick slats and secure with nails or screws.

The width of the fabric should fit between the small holes for the ropes, and its length should be greater than the length of the prepared one. wooden structure. Firstly, the fabric will need to be folded, and secondly, it should sag a little so that you can sit in the chair.

Wrap the narrow side of the fabric around the thick slats and sew by hand or machine. Insert a short rope into the free holes in the top rail of the hammock and tie each of them with a strong knot near the rail. In the same way, tie two long ropes to the bottom rail.

Then tie all four ropes to the third thick batten. Make two more holes in it for the rope, insert it, tie it and hang the chair by some hook or thick branch.

This hammock looks more impressive, but it will take a lot of cord to make.

What do you need

drill;
3 thick wooden slats approximately 80 cm long;
2 thin wooden slats approximately 90 cm long;
nails or screws;
hammer or screwdriver;
2 thick strong ropes approximately 1.5 m long;
3 thick strong ropes approximately 2.5 m long.
16 braided cords 8–9 m long.

How to do

Make exactly the same wooden frame as for the fabric hammock chair. You can immediately tie ropes to it and connect it to the third rail, to which the frame will be suspended. This is also done in the same way as in the previous method.

But the seat itself will be woven from cords. Fold each of them in half and tie it to the top rail of the hammock (if you immediately connected the structure to the third rail, then the rail you need will be in the middle). Then you can weave a chair in the same way as a regular hammock made using the macrame technique. But you can make a more original pattern.

When you tie all the cords to the rail, you will have 32 cords hanging down. Take four of them and place the first cord under the last one.

hunker.com

Place the last cord under the middle two and pass it through the loop. To finish the knot, repeat the same steps again. Then make knots from the remaining cords in the same way.

hunker.com

In the second row and in all even rows, repeat the knot, starting from the third cord from the beginning, and in odd rows - from the first cord.

hunker.com

The entire hammock will consist of identical nodes, which alternate with each other in a checkerboard pattern. This is what this weave looks like:

To tie the hammock base to the bottom rail, wrap four cords around it and tie a strong knot.

The hammock is hung in the same way as the previous one.

A hammock with a metal frame is simple, convenient and durable. The main thing is to do reliable design, it can be disassembled or welded tightly - as they say, there are no comrades in taste and color.

To make it easier for you to decide, let’s consider different variants How to make a metal hammock stand with your own hands.

Yes, if you don’t have a hammock yet, don’t rush to buy one, perhaps you’ll decide to make one yourself - take a look at our article: “how to make a hammock with your own hands.”

DIY metal hammock stand

Let's start our selection with simpler options.

In general, in most cases round and square metal pipes will be involved; we will discuss different options for connecting them together (which is especially important for those who do not have welding).

So, the first round hammock stand metal pipes no welding. In the photo below, on the left in disassembled condition, on the right - in assembled form, ready to have a hammock hung on it (by the way, two at once). How was it made? – look at the photo instructions below.

The author made three racks (for two hammocks), if you need to hang only one hammock, you will accordingly make two “tripods”. Each tripod consists of four pieces of pipe. Three are legs, and the fourth will go to the crossbar, on which the hammock will later be hung. The crossbar is assembled from two halves; a half with a reduced pipe diameter at the end is tied to one tripod - so that it fits tightly into the pipe tied to the other stand.

Here you may need welding: weld a piece of pipe of a smaller diameter to the edge of one pipe to ensure a tight connection; Or you can get away with little pain, for example, buy threaded pipes for the crossbar and use fittings to connect metal pipes.

A few words about the design. Everything you need to connect three pipes is shown in photo No. 1.

Namely:

Plugs for pipes (on the bottom so that the legs do not sink into the ground);
Anchor bolts with rings and nuts for them (the nuts should not fit freely into the pipe);
An anchor bracket with a threaded pin (for connecting three rings from anchor bolts together).

Actually, everything is quite simple: you need to hammer one nut into three pipes with a hammer, screw the anchor bolts into them. Which are then connected together using an anchor bracket. Next, tie the “crossbar” pipes to the cord. And so make two tripods.

Those. for an iron hammock stand (one) you will need: 6 pieces steel pipe 180 cm each, two 150 cm each; 6 plugs; 6 anchor bolts with rings and nuts for them; 2 anchor brackets. You can change the dimensions of the pipes (length and diameter) at your discretion.

In addition, using this principle, you can make a stand in reverse for four hammocks at once. What can be useful on a hike, hunting or fishing. And at the dacha it will be very useful for relaxing with friends.

An alternative option for such a stand: drill holes in the pipes and connect them with bolts and nuts.

Please note: for greater stability, the legs were additionally connected with a cord almost in the middle.

And another modernization, but here they already used welding. And notice that the pipes are flattened at the joints with bolts. And a board as a crossbar.

By the way, it is more convenient and easier to work with wood - perhaps you will like our selection more: “”.

In addition, the middle was stabilized using pipes and clamps.

Overall, it turned out to be a good metal hammock stand.

Those who have welding skills can make the following iron hammock stand (by the way, it can also be disassembled and reassembled at any time). This design has only 4 legs. I won’t describe much, everything is visible in the photo, you can experiment with the sizes.

This is what this stand looks like when assembled.

Notes have been made for clarity different colors.

We have already mentioned threaded pipes and fittings for connecting metal pipes; with their help, you can assemble a very reliable stand for a hammock.

To begin with, I suggest you visual diagram such a stand for a hammock made of metal pipes.

And a couple of live examples.

And modernization.

You can find a lot of useful things at a hardware store. Give free rein to your imagination!

Metal hammock stand drawing

I present to your attention a simple drawing of a hammock stand. To create a stand based on it, you will need welding to one degree or another. Below the cut are several different ideas.

The first option with a minimum of welding. Namely: sections of 15-20 centimeters were welded to the support pipes (on which the hammock is hung) from below. They were then fixed with bolts between two pipes at the base, which made it possible to create robust construction(which can be disassembled for easy transportation or storage).

In the same stand, all parts are welded, and with external parties reinforcing bars were added to stabilize the structure.

In this hammock stand, the bottom was “reinforced” by further adding iron corners on both sides along the entire length of the bottom beam (top right corner).

Video with an example of assembling a factory stand, in principle by analogy (if available necessary materials and skill) you can make such a stand with your own hands.

In the first two videos, a profile was used: 60*40 and 40*40, thickness 2 mm, thrust bearings - strip 80*5 mm.

By the way, you can use old pipes, if available. Paint the finished metal hammock stand in your favorite color, and the result will exceed all expectations.

And on next photo The example shows the necessary thing: a system of sliding racks. This great way increase the distance between the hooks on the supports. After all, the hammock may stretch out, or you simply want to hang a new hammock that is longer than the old one.

Factory model: on it, pay attention to the holes drilled on the supports themselves (for the hooks), i.e. You can adjust the height of the hammock - another useful bonus.

The only thing I want to point out is Special attention: in the above options, it may be unsafe to place the iron support in the middle at the bottom. Especially if you have small children! Or make it as low to the ground as possible and not too large. Or check out the stand below with a rectangular base.

And finally, a photo example from the “author burns” series. To connect the structure, special metal corners(pictured No. 1), but not timber was inserted into them (which is much more appropriate), but metal pipes with a large diameter. It’s hard to imagine the weight of such a stand, but one person obviously can’t move it. In general, experiment, but without fanaticism!

Original do-it-yourself metal hammock frame

At the finish line, I offer you a hammock on a metal frame in the shape of a boat, or whatever associations you have. True, to create such a miracle of technology, you will need, in addition to welding, a special machine with the help of which the profile is rounded.

Such a round frame for a hammock can be made from a single pipe on legs or assembled from several parts.

I hope we answered your question: how to make a hammock stand with your own hands from metal. And that's all for me. I wish you inspiration and creative success!

Making a frame for a hammock with your own hands is good idea. These products are quite expensive, but their design is simple. Therefore, creating a stand for a summer house yourself will not be difficult. You just need to choose suitable drawing, purchase some materials and spend a few hours of time.

A lot of effort will have to be put in if you need a stand with rounded shapes, as in the photo. In this case, you need to have a special tool for bending wood. This is quite labor-intensive and requires some experience. There are simpler drawings for beginners.

What to make it from?

A DIY hammock stand is made of wood or metal. The difficulty of working with both materials is approximately the same. Below are drawings of frames for summer cottages made of wood and metal.

Wood frame

The wooden support has long term service, is quite durable and aesthetically attractive. She will not only become useful item for a pleasant stay, but also for decorating the dacha.

For work you will need:

saw, jigsaw or grinder;
hammer, mallet;
screwdriver;
furniture conductor;
clamps.

Materials:

Wood. Beams and boards are required.
Hardware – self-tapping screws, screws, nuts, washers, hooks (eyes).
Furniture glue or PVA.

The stand is created in several stages:

Preparation of all parts future design.
- Base. Consists of two beams 1850 mm long and two boards 1500 mm long. Grooves are made on the beams at a distance of 200 mm from the edges. The depth is equal to the thickness of the boards used, the width is the width of the boards. At the ends of the beams, at a distance of 20–40 mm, holes are made for bolts. The beams are laid on boards parallel to each other at a distance equal to the thickness of the support beams used (on which the hammock will be hung). For better fixation, you can connect them using wood glue or PVA. In this case, the product must be clamped at the joints.
- Supports. 2 beams 1700 mm long are required. At one end a cut is made at an angle of 45°, at the other there is a hole for a hook. 2 supports with a length of 520 mm are also made.
Opening with varnish. Since the stand will be used in the country, under open air, it can be opened alkyd compounds– the smell will dissipate fairly quickly. All openings must be protected before processing.
Assembly of the structure. If the parts are made correctly, then there will be no problems with assembly - the drawing provided above will allow you to complete the work without difficulty.

Metal frame

The presented drawing shows a rack made using metal pipes and special connecting elements. The dimensions of the support can be selected independently, depending on the dimensions of the hammock, the number free space in the country. The main thing is not to change the width of the support. The drawings indicate the optimal value that is guaranteed to make the product stable. The connection points can be additionally secured with through bolts. You can also cut threads.

Bentwood frame

This product is well suited for those who love complex tasks. The frame has simple design, the most difficult thing in the work is to bend the beams. To give wood a similar shape, it is necessary to soften, bend and dry it. There are several ways to make a material plastic:

Steam finishing. The beams are loaded into a pre-prepared box, and steam is supplied to it. For every centimeter of beam thickness, approximately 1 hour of processing is required. You can also perform treatment with a steam generator.
Soak in hot water.
Use ammonia solution. The longer the tree is in it, the more plastic it becomes.

After the required softness is achieved, the wood is bent. To do this, either use special machines, or simply place the beam on supports, and place a load in the middle. The greater the bend and the longer the material, the higher the supports will be required.

A hammock is the key to a great summer holiday in the country. Find out how to make a hammock with your own hands here. And today we’ll talk about how to make a wooden hammock stand with your own hands.

Because it’s not enough to just make a hammock, you still need to put it somewhere. And the wooden frame is the most best option, accessible to everyone. You can always buy it, or you can make it yourself. It will be cheaper that way, and appearance The finished stand will fit into your landscape design.

When you make a hammock frame with your own hands, pay attention to safety precautions! Especially if you have small children. Firstly, try to bury all kinds of nuts and bolts in the finished rack, and it is better to cut off the excess protruding threaded parts. Well, take care in general about the reliability of your hammock stand - choose thick boards and beams, and make the lower part solid (so that the stand does not tip over).

Hammock stand made of wood, drawings with dimensions

Let's start our selection of master classes by looking at a simple drawing of a hammock stand.

In general, it is quite convenient to work with wood, therefore, for those whose hands grow where they should, all the drawings and ideas will be simple.

Hammock stand drawing No. 1

As you can see, it's a fairly simple design.

This wooden frame is made of:

The bases are two beams in the center (in the photo under the letter “A”) and legs that give the rack strength (in the drawing “D”);
Support beams “B”, which are attached between the lower bars. Their lower part should have a cut at an angle of 45° - this way they will be screwed on at an angle, which will significantly increase the space for hanging the hammock;
The thrust inserts are labeled “C” in the figure. On one side, a cut is made at an angle of 45° (this part will be connected to the supporting beam). And the second edge remains smooth; it is also fixed at a right angle between two boards at the base.

There is a bonus in the drawing - under the letter “E”, this is a stand for a sun umbrella.

Of course, a garden umbrella stand is an addition you can do without. But there will probably be those who will find it useful. After all, not everyone has trees or gazebos in their yard or at home that create shade. And this way it will be possible to hide from the scorching summer sun. In this case, you will need to add only one piece of timber to your frame, with a hole drilled in it for the umbrella handle.

Moreover, for those who have free time and the issue with the sun is relevant, I advise you to look at our other selection: how to make a frame for a hammock with a canopy and roof.

All dimensions are indicated on the drawing. Of course, you can change them as you wish. And now a small master class with step-by-step photos.

The result is a beautiful wooden hammock frame that is comfortable and easy to move.

If you doubt the reliability of this rack, just take a thicker beam. Of course, in this case, move alone finished frame By garden plot it will be hard. But there will be no doubt about its strength - and its carrying capacity will increase.

I found a video for you with a similar stand made of 100x100 timber.

Mounting studs cut:

The first into 4 parts of 25 cm - fastening the legs;
The second into 3 parts of 33 cm each (+ from the third I cut off a piece of 33 cm) - intermediate connecting ones;
The remainder of the third goes to connecting the struts diagonally with the load-bearing beams.

The author names all the sizes in the video, so take a look.

And here is another option for modernizing the original drawing.

Under point No. 9, a cut of the upper part of the hammock’s supporting board is shown - this is an option for fixing a hammock without screws with a loop, an eye bolt or anchor bolt. In general, for those who don’t have them and don’t want to buy them.

Please note: the connection between the supporting board and the thrust board was secured with pieces of plywood on both sides.

And one more option wooden stand for a hammock. This time, mostly medium-sized timber was used, and the thrust inserts were made of boards and placed on both sides (lower right corner in the photo).

DIY hammock frame drawing No. 2

The second option is similar to the previous one, here we also make the base, but the mounting option load-bearing beams and the struts change. They change places, of course, and their angles of inclination change.

For stability under lateral loads (swinging), a cord/rope or metal cable must be added to the finished wooden stand - in photo No. 6.

Video example.

Cool video tutorial with double bracing.

By the way, the finished rack can be painted in any beautiful colour. The author painted his hammock frame in Blue colour, you can paint it in your favorite color.

This video review is for those who are afraid to deal with angles other than 45°.

Above I presented to your attention an example of such stands made of timber. However, it can be easily assembled from boards. Let's look at the step-by-step photos.

And of course a video for better understanding. In fact, such a stand can easily be assembled by yourself or with a little help from your wife.

And little pranksters (who have them) will always gladly come to the rescue - especially for testing a ready-made hammock stand.

Now let's look at some simplified examples. Bearing supports(those on which the hammock is hung) can be attached to the base perpendicularly, so make 45° cuts on the support boards (provided that an isosceles triangle is formed).

And by the way, for greater stability of the hammock stand, you can make not 2 legs, but four.

In addition, the finished stand can be decorated with night lanterns. This way you can enjoy your evening relaxation in a hammock.

Or this option: load-bearing boards are additionally connected to each other, and the legs of the hammock are fixed to the ground. True, I am confused by the pegs sticking out of the ground - I would not recommend leaving them like that. If you really want to firmly attach the hammock to the ground, then do it using reinforcement as shown in the upper part of the photo in the middle. Well, in general, of course, in this case it’s easier to concrete two beams and hang a hammock between them.

The third version of the hammock stand drawings

We smoothly moved on to the next version of the wooden stand. I signed everything on the diagrams in detail. It is assembled from boards.

If you process the entire board - rounding the edges, etc. the result is pleasing to the eye.

Simplified version.

Therefore, in the same principle, you can make hammock stands from timber.

By the way, a cable or cord is also useful here to stabilize the stand.

Their fixation is close.

If there is no cable, you can use boards by analogy.

As a matter of fact, this technique is also applicable to previous models of stands.

Inspired by other people's ideas, you can come up with your own unique hammock stand.

Here are some more interesting ideas for you.

Hammock stand in the form of a frame; if you remove the hammock, children can use it as a football goal.

And here’s an unusual option: you can take the trouble to make this beautiful stand for your child’s room.

Folding Wooden Hammock Stands

Thorough beautiful frames This is great for hammocks, but there isn't always room to store them. The summer season will fly by quickly, and in our weather conditions It is better to remove the wooden stand (this way it will last much longer).

Therefore, I bring to your attention a small selection of folding racks.

The first stand, when assembled, looks like one of those we reviewed above.

However, it folds up very conveniently, allowing you to save space in the yard and garage.

I specially painted the boards in different colors to make it clear how it works. I hope you figure it out.

And here is a very simple version of a folding wooden stand for a children's hammock.

Couple useful videos examples.

This interesting option The stand is made of plywood, its structure resembles the stands from the previous videos.

Do-it-yourself hammock frame made of timber

All previous drawings are applicable to timber; moreover, we gave examples of racks made from timber. However, I brought out a couple of options separately, because they are fundamentally different from the previous stands.

Let's start with the most beautiful, in my opinion, frame. Look how amazing he is, and most importantly, reliable. This stand will decorate any garden.

All parts are cut from timber of the same diameter. In the photo, under point 1, I wrote the length of each piece from this rack. The edges of each cut are mirror-cut at an angle of 45 degrees.

In general, the work can be divided into two stages:

Cut the timber into the required pieces, cut off their corners;
Proceed with assembly (using screws we assemble all the pieces into a single structure).

The result is simply excellent!

The following type of racks is widely available in stores; you can buy them without any problems.

But if you want to make such a stand at home with your own hands, but you don’t have the opportunity to weld iron corners like in the video. Pay attention to the mounting angles that are sold in hardware stores. With their help, you can assemble a rack just as good, and it will hardly put a dent in your pocket.