Defrosting the refrigerator from time to time is necessary for the device of any modification. Even advertised refrigerators with “no frost” technology need to be defrosted, although this takes relatively little time. For older models (such as “Dnepr”, “Stinol”, “Snaige”), cleaning of frost (frost) must be done once every two weeks, for modern ones - once every year and a half.
If you can’t do without defrosting, then let’s at least do it correctly and quickly. You need to know how to quickly defrost a refrigerator in order to save all the food taken out of it. And how much time you will be able to save!
No matter how much engineers teach a refrigerator to defrost itself and get rid of accumulating frost (sometimes they say “frost”, from English word frost), he doesn't care sanitary standards washing and cleaning are required once a year and a half.
Preparatory procedures before quickly defrosting the refrigerator
Before you start defrosting the unit, you need to put the chilled and frozen foods somewhere so that they do not have time to spoil.
Now is the time to start defrosting your refrigerator.
A little theory about modern refrigeration technologies
Modern refrigerators, which, according to manufacturers, do not need to be defrosted at all, operate on the same principle.
- A small fan rotates constantly inside the refrigerator, ensuring uniform cooling of all the air inside. refrigerator. Frost from moist air that enters the unit every time the door is opened does not form over the entire surface of the wall, but only in a few limited places. While the compressor is idle, this frost has time to melt. The water flows into a special tray above the compressor. As soon as it starts working, the heat generated causes the water to evaporate. This is how frost constantly disappears from the refrigerator. And the technology for permanently removing it is called no frost;
- It turned out that the price for constantly removing frost (frost) is increased noise and energy consumption of the refrigerator (the fan is constantly spinning!). Therefore, they learned to ventilate the freezer compartment statically, without using ventilation. Forced ventilation remained only in the freezer to get rid of frost (frost). This development of no frost technology is called frost free.
We remove frost using the no frost technology yourself
Most of all you will have to tinker with older refrigerators. Both Stinol and Bosch are not particularly different in this regard.
- First of all, disconnect the electrical appliance from the network (pull out the plug from the socket.
- Open the refrigerator doors and lock them in the open position.
- Under the freezer compartment you need to insert a special plastic construction designed to collect ice that has fallen off the walls.
- If there is so much ice frozen that a standard tray cannot be inserted, you will have to place a basin of more or less suitable size in the refrigerator.
- The bottom of the refrigerator is lined with a fabric that absorbs water well (you can get by with a few kitchen towels).
- We install a switched-on household fan on a stand (stool, for example) opposite the refrigerator.
- Warm flow kitchen air It will melt the snow relatively quickly so that pieces of ice will fall off into the substituted container. To speed up the process, you can instead household fan use a thermal wind blower.
In a modern refrigerator, frost will only be found in the freezer. Double chamber refrigerator It was precisely designed in order to minimize the opening of the freezer compartment.
- We open it and begin to defrost the snow coat with a stream of warm air from the fan.
No matter how much you are convinced of the usefulness of a household refrigerator for defrosting, such units are not very suitable for this procedure.
You should also not put pots of boiling water in the refrigerator and close the doors.
An old refrigerator (Stinol type) will defrost quickly. But the new “coat” after such “defrosting” will begin to grow very quickly, since the moisture accumulated in the depths of the refrigerator simply does not have time to evaporate.
In refrigerators new system a pan of boiling water can easily damage the thin walls of the freezer and refrigerator.
It’s not worth risking the health of your food storage for the sake of defrosting speed. A two-chamber refrigerator may stop working altogether after such a procedure.
Everything is almost ready
- To do this, use warm water with the addition of grated baby soap or a soda solution (a tablespoon per liter of water).
- You can also use special means for cleaning refrigerators.
- To get rid of unpleasant odor The solution is suitable in the freezer and refrigerator ammonia in warm water (a tablespoon per liter of water).
- The washed refrigerator should be wiped dry with clean, soft cloths.
Now you know how to quickly defrost a refrigerator, saving your time and energy. The advice applies to both devices using no frost technology (no frost, frost free, de frost) and relatively old refrigeration equipment.
How to properly and quickly defrost a refrigerator is an important question that faces owners old model household appliance, and to the owners of modern two-chamber refrigeration units equipped with electronic controls.
To answer this question, you need to consider what refrigerators currently exist, what their defrosting system is, because each model defrosts in its own way.
Modern refrigerators have two defrosting systems: one group has a drip system, and the other part of the refrigeration units is equipped with a No Frost system.
Drip defrosting system
This defrosting system operates mainly in refrigerators in the mid-price segment.
It only affects the refrigerator compartment. The freezer defrosts on its own, manually. The drip system involves alternating freezing and thawing processes. 
Compressor running certain time, then turns off. After the same period of time it turns on.
Constantly alternating turning the refrigerator on and off leads to frost appearing on the back wall of the refrigerator compartment while the compressor is running.
This means that the temperature in the refrigerator has reached its lowest possible value. The compressor turns off, the temperature in the refrigerator compartment begins to rise, rise, and the ice begins to defrost and turn into water.
Condensation in the form of water flows drop by drop into the hole under the bottom shelf and ends up in the tray. The evaporation of water from the pan leads to the fact that the side walls of the refrigeration unit are always dry.
No frost
This system is more expensive; many modern refrigerators are equipped with it. Translated, No Frost means without frost.
Refrigerators with such a system are otherwise called windy, because they are based on the operation of fans that evenly disperse cold air throughout the household appliance. 
This way, the products receive the same amount of cold.
Moisture settles on the evaporator. Water freezes and forms thin layer ice on it. But in such a refrigerator there is a heater that melts the water, and it flows into the tray. Then it evaporates. The No Frost system is designed for both the refrigerator and freezer compartments.
Why does ice form?
Ice forms when warm air enters the refrigerator and freezer while opening the door, especially when we open household appliances and we think what we should take.
It is best to decide what foods you need before opening the refrigerator, so that only a small amount of air enters the unit.
Why do you need to get rid of ice?
When a fur coat appears on the freezer, it not only prevents you from getting food, but also interferes with the correct operation of the compressor. The compressor starts working in increased mode. Its effect is reduced. In addition, energy costs increase.
How often should you defrost your refrigerator?
Old domestic models Biryusa and others should be defrosted once a month, and no frost, Frost free or Full No Frost two-compressor refrigerators need to be defrosted once every six months.
Preparing for defrosting 
There is no point in defrosting the refrigerator when it is full of food and there is nowhere to put it. There is no need to defrost the refrigerator when high temperature in the apartment, because after defrosting it will take a long time to gain its parameters, which can lead to disruption of the compressor, engine and malfunctions.
Instructions for preparing the refrigerator for defrosting
How to quickly defrost a refrigerator
How to defrost a refrigerator correctly
How to properly defrost an Indesit refrigerator
To defrost an Indesit two-chamber refrigerator, you need to turn off the power to the household appliance, remove the food, open the door and try to defrost it naturally.
Using a hair dryer or boiling water can harm the refrigerator because they cause sudden changes temperature regime. Boiling water negatively affects the operation of the compressor. Therefore, pour warm rather than hot water into a container of water for quick defrosting.
If the refrigerator has two compressors, then the chambers are defrosted one by one. The products are placed in a chamber that works. The power to the compressors is turned off one by one.
After defrosting the refrigerator, clean drainage hole, wash it with soapy water and dry it. You can also use special wet wipes.
The refrigerator stores food, so it is best not to use it to wash it. various means, the composition of which contains toxic substances. This may harm human health.
Wipe the shelves dry, keeping the door open until it is completely dry. Turn on the refrigerator. Before placing food in it, you need to wait a while until the device freezes a little ice.
How to defrost an Electrolux refrigerator correctly
When defrosting the Electrolux refrigeration unit, be sure to disconnect the device from the network; there is mains voltage in some parts of the refrigerator’s electrical wiring. When combined with water, there may be an electric shock.
When defrosting, do not use hot water or sharp objects to avoid damaging the evaporator.
It is better to defrost the device naturally. To speed up the defrosting process, you can use a fan, but with cold air.
How to defrost a Stinol refrigerator correctly
Only the freezer compartment needs to be defrosted. The refrigerator compartment defrosts automatically every time the compressor is turned off.
If the ice layer has reached 3 mm, then turn off the device from the network, take out the food and leave the door open. Place a cloth in the freezer to absorb the thawed water.
Some Stinol refrigerators have a hole at the bottom of the freezer to drain melt water. Then you don’t have to put the cloth in the freezer, but use an empty basin to collect melt water. To speed up the thawing process, you need to place a container of warm water in the freezer.
How to defrost an Atlant refrigerator correctly
The Atlant two-chamber refrigerator is defrosted differently depending on whether it has two compressors or one.
If there are two compressors, then the chambers can be defrosted alternately or together. If there is only one compressor, then the chambers are defrosted simultaneously.
The fresh mechanism assumes the presence of a water drain. It is necessary to ensure that the drain does not become clogged, otherwise the water does not flow out, it ends up on metal parts, which can lead to corrosion and damage to the thermal insulation. Clean the drain thoroughly with a brush.
Today we tried to answer the question of how to defrost a refrigerator correctly and quickly. We hope that we were able to consider all the nuances of defrosting refrigerators of different systems.
Refrigerators with the No Frost system (literally “no frost”) are designed to save the time of their owners by relieving them of the lengthy defrosting procedure. Manufacturers unanimously claim that “when normal conditions operation, frost is removed from the evaporator of the refrigeration chamber automatically every time the compressor is turned off.” Therefore, units with No Frost technology do not need to be defrosted. But is this really so? Let's figure it out.
No Frost refrigerator: to defrost or not?
Of course, the manufacturers’ statement that their units do not need defrosting should not be taken too literally. The presence of the “magic” automatic defrosting function does not eliminate the need for periodic cleaning of the refrigerator chambers.
The thing is that during operation, various contaminants could form inside the refrigerator, food residues, crumbs, etc. could accumulate. And then, in order to eliminate the possibility of the development of an environment unfavorable for the products, the unit will have to be defrosted manually periodically (1-2 times a year).
In addition, even the most sophisticated No Frost refrigerator can freeze slightly over time, lose cooling capacity, etc. And then manual defrosting will be easy forced measure, otherwise the refrigerator will not work properly.
Attention! If the refrigerator No Frost a lot of ice and snow freezes in the freezer, this indicates a malfunction of the unit. Defrosting will help get rid of ice for a maximum of 1-2 weeks, but may aggravate the breakdown. We recommend calling a technician to repair your equipment.
Defrosting a No Frost refrigerator - read the instructions
So, what needs to be done before proceeding directly to defrosting? That's right - read the instruction manual. It will probably contain information on how to properly care for the unit. If it so happens that you have lost the paper instruction manual, you can find the instructions you need by following the link, or by studying our tips on proper defrosting.
General recommendations for defrosting and cleaning a No Frost system refrigerator
- Unplug the refrigerator. Before you start defrosting the unit, unplug it from the outlet.
- Empty the refrigerator compartments. Remove all products, shelves and trays from it. After this, the door should be left open.
- Do not try to speed up the defrosting process. Allow the refrigerator compartments to thaw naturally; in a No Frost unit this will not take much time. Do not try to speed up defrosting by using a hair dryer, containers with hot water or sharp objects - thereby you risk damaging the equipment.
- Do a wet cleaning of the refrigerator compartments. Once the unit has completely thawed, wipe down all interior and exterior surfaces of the refrigerator, as well as drawers and shelves, with a damp sponge. It is important to remember that you do not need to use aggressive cleaning agents for this purpose, which can damage the plastic. Dishwashing liquid or a solution of table soda is sufficient. After treatment, you need to wait until all surfaces of the refrigerator are completely dry.
- For refrigerators with partial No Frost: clean the drainage hole. If your unit has a drip defrosting system for the refrigerator compartment, it would be a good idea to clean the drainage hole to remove condensate. It is usually located at the bottom of the back wall (above or behind the fruit and vegetable drawers). It can be rinsed with warm water from a syringe and/or cleaned with a cotton swab.
- Plug in the refrigerator. After defrosting and cleaning, turn on the refrigerator. But you should not immediately place the products on the shelves; wait until the unit reaches the set temperature.
The refrigerator allows you to keep food fresh for a long time. As for any household appliances, the refrigerator requires regular care - both the old country Biryusa and the brand new two-chamber Indesit will have to be defrosted and washed periodically. It is important to know some features and nuances proper defrosting to extend the life of your assistant.
Why defrost the refrigerator?
Food is stored in the refrigerator, so crumbs constantly appear, liquids spill, which after a while causes an unpleasant odor to form in the refrigerator. Therefore, when defrosting, the device must be thoroughly washed. Hygienic care with defrosting will prevent the growth of bacteria.
In addition, the formation of ice puts additional stress on the compressor and, as a result, your electricity bill will increase. And placing food in the freezer with a frozen “fur coat” is quite problematic.
How often should you defrost the device?
Here the level of education of the naledi will tell you. Signal for cleaning refrigerators without automatic system defrosting is caused by the formation of ice 7–10 mm thick.
In matters of the required defrosting frequency, you need to focus not on the manufacturer of the equipment, but on the built-in defrosting system:
- Older “Soviet” models of refrigerators that do not have an auto-defrost system need to be defrosted quite often - at least once every 2 months.
- Models of the 21st century are produced on the basis of two automatic defrosting systems:
- drip technology: while the compressor is operating, ice (frost) forms on the back wall of the refrigerator. Then the compressor turns off, the frost melts, flowing drop by drop into a special container, and evaporates there. Therefore, this technology was nicknamed “crying”. The disadvantage of the drip system is that automatic defrosting only applies to the refrigerator compartment, but not to the freezer, which still has to be defrosted manually;
Refrigerators with drip system defrosters are quite quiet and consume less electricity than their counterparts
- The No Frost system (so-called “dry freezing”) is based on the operation of a fan that distributes cold air. Moisture condenses and evaporates directly in the cooling element, and a properly functioning refrigerator defrosts itself by controlling the melting of ice.
The No Frost system applies not only to the refrigerator, but also to the freezer
- drip technology: while the compressor is operating, ice (frost) forms on the back wall of the refrigerator. Then the compressor turns off, the frost melts, flowing drop by drop into a special container, and evaporates there. Therefore, this technology was nicknamed “crying”. The disadvantage of the drip system is that automatic defrosting only applies to the refrigerator compartment, but not to the freezer, which still has to be defrosted manually;
There are no devices that absolutely do not require defrosting. Even refrigerators with No Frost technology periodically need to be cleaned - at least once a year, you need to remove all shelves, containers and wash the inside walls warm water. It is not recommended to do this while the unit is turned on - the compressor will be overloaded.
How to defrost a refrigerator
The main tasks when defrosting a refrigerator are to remove ice and keep food fresh. If you have a two-compressor refrigerator: you can put them in one chamber and defrost the second, and then do the opposite. If your unit has one compressor, then the products will have to be removed from it completely.
It is not advisable to defrost the refrigerator in the summer - yes, the defrosting process will happen faster, but then it will cool down to desired temperature it will be more difficult for the compressor due to the large difference in degrees.
Defrosting a refrigerator includes several steps:
- Remove food from chambers. You can store food while defrosting a single-compressor refrigerator in different ways:
- Remove all shelves, drawers, and containers from the refrigerator. Wash them using a soft sponge and liquid dishwashing detergent.
Powders and any other abrasives, as well as hard sponges, should not be used when washing shelves and the inside surface of the refrigerator!
While the refrigerator is defrosting, wash its shelves and drawers
- If there is ice on the walls of the refrigerator, you will have to wait until everything thaws completely. The best option defrosting - naturally - just leave it for a few hours or overnight (depending on the amount of ice). If there is no ice, start cleaning the refrigerator.
- If the refrigerator has a special container for defrosting, pour out the water as it accumulates. If not, then place a small ladle or old towels near the back wall of the device.
Place a towel under the refrigerator to prevent water from damaging the flooring.
- Prepare soda solution- 1 tablespoon per 1 liter warm water. In addition to removing stains and other contaminants, the soda solution destroys unpleasant odors.
- Wash the walls of the refrigerator with the resulting solution using a microfiber cloth or other soft material. The same solution can be used to wash the outer walls of the refrigerator.
Use soft materials to clean the walls of the refrigerator.
Be careful not to allow moisture to get into the switch or lighting system when washing.
Set the temperature of the refrigerator compartment to 0 ° C and disconnect the refrigerator from the mains by removing the plug from the socket.
Set the temperature regulator to zero
Removing stains when washing the device
To remove dried stains, use the following cleaning mixture:
The described defrosting method is the most gentle on equipment and is applicable for any model of refrigerator - from the humming Soviet ZIL to modern models Bosch, Indesit, Beko, LG, etc. The method is also suitable for built-in refrigerators, but be careful: assemble melt water in time, do not allow liquid to enter the rear panel of the unit.
Video: general cleaning and defrosting the refrigerator
When defrosting the refrigerator, do not use knives, screwdrivers, hammers, etc. Even if you carefully break off the ice, there is a risk of damaging the surface. Repairs in this case will not be cheap, so it is better to take your time and let the refrigerator defrost naturally.
Ways to speed up defrosting
There are situations when the refrigerator or freezer needs to be defrosted faster than naturally. To begin, unplug the device, remove the food and all removable parts. Then let it sit with the door open for at least half an hour.
There are several ways to speed up the defrosting process:
- Wet a soft cloth in hot water (from the tap) and wipe the ice layer. Repeat as the fabric cools.
- Fill a rubber heating pad with hot water and place it on a clean cloth in the freezer. Leave the freezer door open.
A hot water bottle will help defrost your refrigerator faster.
- Place in the freezer cutting board made of wood and place a pan of hot water on it. It is not recommended to use boiling water; there is a risk of damaging the plastic.
Steam from hot water speeds up the melting of ice in the freezer
- If you don't have a heater, you can replace it with a hairdryer. However, this is not very convenient, since you will have to hold the hair dryer in your hands the entire time it defrosts. Placing it inside the freezer is dangerous, like any other electrical appliance. Do not direct hot air at the seal - this will damage the lining.
The fan heater can be replaced with a hairdryer
- Convenient to use for defrosting washing vacuum cleaner: you need to switch the mode to blowing, change the wide brush to narrow nozzle and direct the air alternately to different areas of the ice.
Fill a spray bottle with warm water and spray onto the ice layer. Repeat the process, collecting any melted water with a rag.
Spraying ice with warm water is effective and sufficient quick way defrosting
For emergency defrosting, you can also use special “defrosters”. Their operating principle is based on accelerating the melting process with the help of special substances in the composition. Depending on the thickness of the ice layer, defrosting the refrigerator using the product will take 25 minutes.
Professional product - defrost - suitable for all models of refrigerators
To speed up defrosting, you can use a heater or fan heater. Place it opposite the refrigerator so that melted ice does not reach the appliance and hot air does not blow directly onto the rubber door seal.
One of the most effective ways quickly defrost the refrigerator - use a fan heater
If ice forms in your refrigerator too quickly, it may need to be replaced. rubber seal. Due to poor fit warm air enters the refrigerator and ice forms.
Video: how to quickly defrost a freezer
You should not abuse emergency defrosting methods - this is still a load on the entire refrigerator as a whole and the compressor in particular.
Restarting the refrigerator after defrosting
The rule is very simple - place dry, clean shelves in a refrigerator that is completely ice-free.
The refrigerator can become your faithful assistant on long years. To do this, follow simple rules of operation and regular maintenance. Even modern models need cleaning. In models not equipped with automatic defrosting, check the level of ice and get rid of it in a timely manner. Do not abuse emergency defrosting methods and do not use foreign objects to remove ice.
A refrigerator exists in every house or apartment because food is stored in it. Today, the range of such units on the market is overwhelming, and it is not always easy to make your choice. In addition, you can often hear about the No Frost system, but what is it? This is an opportunity not to constantly defrost the refrigerator. But this does not mean that you no longer need to unplug it and wash it.
Therefore, “how to defrost No Frost refrigerators” - actual question. You need to know that this is a specific operation that has its own sequence and certain stages. It is profitable to purchase a No Frost installation, but you need to turn to theory, which will then be put into practice. This is required so as not to send your refrigerator for repair.
How is everything going?
Know Frost is not such a complex technology that you can’t figure it out. In simple words, there is a special ventilation system inside, it drives the cold throughout the entire area. Do not forget that the compressor stops and, to prevent ice from forming, the existing liquid is discharged according to a special scheme. This is precisely why education does not occur large quantity condensation, which then becomes an ice crust. In addition, bacteria and microorganisms do not appear.
As a result, knowing how this process works, I want to understand whether it is necessary to defrost the No Frost refrigerator. Masters say that this operation should be carried out in mandatory, because this prevents the formation and accumulation of negative bacteria that harm the products inside. Once every few months is enough to maintain cleanliness and comfortable conditions food storage. But the washing should be of the highest quality.
Why does a frost crust form?
The system has a unique operating process, but why does frost still collect on the walls? There are a number of reasons for this:
These are the main reasons. Although it also happens that when jars are placed close to the wall or food is placed, frostbite occurs upon contact. Because the cold air has nowhere to escape, it accumulates and a crust of ice grows.
Why defrost?
How to defrost a No Frost refrigerator and for what purpose? Before starting the process, it is worth understanding why this is being done. One of the necessary operations is washing the unit.
Because it is not so easy to maintain careful operation all the time. As a result, plaque appears on the walls. In addition, you may forget to close the door all the way. It is worth remembering that the unit stores a variety of products with their own odors that can accumulate. To completely remove any odors, the No Frost refrigerator must be defrosted.
When a suitable environment for bacteria is formed, they begin to actively multiply. Everyone tries to remove them, and the only solution is to wipe and disinfect them in a timely manner. The procedure itself is simple, but before you begin, you should understand what is at stake. Experts believe that by making mistakes, it is possible to create conditions for the unit to fail.
Defrosting methods
Conventionally, the entire process is divided into several types. But it is important to understand how to defrost a No Frost refrigerator. Most often there are two options - drip and wind. In addition, you can always use the two methods together and create a quick process of complete defrosting. Below we will consider both methods in more detail.
In such a situation, the operation of the main device slows down its operation process, and heating is already minimal. As a result, the droplets in the form of condensate simply evaporate without leaving a residue, after which the operation of the motor resumes. There is a big plus - frost does not form and the temperature is different throughout the chamber. And another plus is that the maximum cold temperature is restored quickly, even when the unit is open. In this case, both the refrigerator itself and the chamber can have such a process. There is a downside - all products must always be closed. Since air currents will dry out everything that is there. Another disadvantage is the high noise during operation. The evaporator is large and space is limited when installing it.
Drip method
What is the essence of the operation? Its meaning lies in the presence of a flat evaporator on the back wall of the refrigerator. When the compressor is started, frost begins to form on it, the motor turns off, and liquid appears. And all the water that appears leaves through a specially created path. The container is not located in the chamber; when heat appears, any liquid evaporates. As a result, nothing unnecessary will form in the chamber of the device.
One of the main advantages is low cost and maximum efficiency. The equipment itself is basic, so any breakdowns do not require large financial investments. Experts talk about the reliability of the entire installation; repairs are rarely required. But there are always negative sides. The method is not suitable for the cold chamber, nor is it suitable for the freezer compartment. And in order to completely defrost the No Frost refrigerator, you need to turn it off at for a long time. This will take more than a day.
What methods will bring quick results?
Does No Frost refrigerator defrost? It is now clear that the answer to this question is positive. Moreover, if you comply simple recommendations, then defrosting will take place quickly and the service life of the unit will be extended.
How to defrost a Samsung No Frost refrigerator? The first thing is to take the instructions and read what is written there on this issue. It is in such papers that everything is needed and it is described which actions are completely prohibited.
When the apartment or house is too hot, such processes are not recommended. Because sudden temperature changes threaten the compressor with malfunctions. There are units on sale with two or one cooling circuit. When there are two of them, you can perform ice removal procedures on one camera. Most often you have to unplug the refrigerator.
Sometimes it is worth carrying out a complete flushing operation. To do this, the unit is moved away from the wall and everything is cleaned. A lot of dust often collects on the back wall. It needs to be removed first. Not everyone can expect long time, and to make the procedure go faster, some use a hairdryer. It helps not only the moisture evaporate quickly, but also the temperature inside to become positive.
There is not always time to use a hairdryer. In such a situation, the doors are opened and the unit is left for two hours. Do not forcefully remove pieces of ice with sharp objects, otherwise damage to the walls and more may occur. When such a refrigerator with the No Frost system is washed and dried, it quickly gains cold after being plugged in (which means food is immediately put into it).
How much to wait?
The best time is 24 hours for complete thawing to occur. If it is necessary to turn on the unit earlier, wait at least 12 hours. And there are reasons for this, since when the compressor operates on the condenser high pressure, and after disconnecting it drops. But this happens gradually; if you turn it on immediately, the pressure will jump. At this second, the motor will be under heavy load and will fail.
Conclusion
So, we found out whether it is necessary to defrost the No Frost refrigerator and how to do it correctly. Everyone should know that it is better to predict unpleasant situations than to correct them later. To do this, you need to create preventative measures for your equipment. Don't wait until big ice appears and something goes wrong. If you regularly carry out cleaning, you will not need much time in the future for procedures of this nature.