How to change fittings on a plastic door. How to repair a balcony door with your own hands? Plastic door handle repair

Content:

Plastic doors are made from relatively durable material and are equipped with high-quality fittings. But during long-term use, as a result of natural wear and tear, the mechanisms begin to loosen, the seal loses its plasticity and cracks, defects from mechanical stress appear on the surface of the door, in general, we can say that the plastic door is broken. Many faults can be eliminated by repairing plastic doors yourself.

Do-it-yourself repair of plastic doors

The plastic door on the balcony does not close well. Video

During prolonged use, natural subsidence occurs under its own weight. plastic door. It begins to close and open poorly - clinging to the box.

Recovery normal operation The door is tightened by tightening or adjusting the hinge mechanism.

The entire door is attached to two hinges. Bottom and top. It seems to stand on the bottom one and the top one keeps it from moving horizontally.

To move the door horizontally, you need to turn the adjusting screw located at the end of the canopy on the door leaf, just the top hinge. And to adjust the blade vertically, you need to tighten the screw on the bottom hinge

For more information about how to repair a plastic door if it doesn’t close well, watch the video

The handle is hanging on the door

During operation, it is constantly subject to increased mechanical loads. As a result, a natural gradual unscrewing of the mounting screws occurs. To tighten them, you need to remove them or turn them to the side, it depends on the design of the handle, decorative cover.

Loose screws are tightened using a screwdriver. The decorative cap returns to its place.

The handle on the plastic door is loose, repair - Photo 1

Broken handle, latch or locking mechanism

This failure can occur if the connection between the handle and the core is broken or some part fails. internal element castle To find out the reason, you need to remove or turn the decorative cap. Unscrew the fastening screws.

If the pin connecting the handle to the core is cut off, then you need to knock out its remains. Insert new one.

If the breakdown is related to the handle, then you just need to replace it with a new one. Tighten the mounting screws. Replace the decorative cap.

If it turns out that the lock itself is broken. Then you need to remove the handle and pull out the core. Unscrew the fixing screw at the end of the blade and remove the lock. Install a new lock and assemble the entire locking mechanism in reverse order.

Advice: When buying a new lock or handle, you must have a similar system and the same company.

Replacing the seal

Replacing a plastic door seal - Photo 3

You have noticed that there are drafts from the plastic doors. They cannot be eliminated by adjusting the position of the door leaf. This means the seal needs to be changed.

We buy a new rubber cord and good glue to fix it.

Advice: Today, seals from German companies are characterized by excellent quality and long-term operation. When purchasing a rubber cord, you must carefully ensure that there are no cracked or deformed areas along its entire length..

To restore the tightness of the door, the following operations must be performed:

Carefully remove the old seal from the grooves in the door leaf.
Carefully remove any remaining rubber cord.
Degrease the surface in the grooves.
Apply a continuous tape of glue into the groove.
Installation of the new sealing cord begins from the corner. Lay it in one piece without stretching or compressing.

Advice: To seal throughout long term did not lose its elasticity, it is advisable to apply it twice a year in the off-season thin layer lubricants, such as Vaseline.

Surface restoration doors

Despite the excellent strength of the plastic, small dents and scratches still appear on the surface of the door and frame during long-term use. This significantly affects their attractiveness.

Plastic door repair - Photo 4

At home, you can repair minor damage using a special adhesive. For this area with scratches and dents, you need to degrease it first.

Apply a thin layer of glue carefully. After it hardens fine sandpaper we need to clean these places. After degreasing, cleaned defects are covered with regular or tinted varnish.

To eliminate more serious faults, it is recommended to invite specialists. Especially if the doors are still under warranty.

A metal-plastic balcony door is quite reliable, but it is also subject to wear and tear over time. The most common problems are sagging under its own weight, drying out of the rubber seal, breakage of handles and fittings.

Failures that you should not try to fix yourself include:

Cracks in glass - such work requires replacement of the double-glazed window;

Violation of the integrity of the seams of the door frame or leaf;
“Torn out” loops;
Hardware breakdowns.

Everything else can and should be repaired yourself, so as not to waste money on the work of craftsmen.

Door adjustment

The most frequent malfunction metal-plastic balcony doors - sagging. If the door catches on the frame when closing and you have to lift it by the handle, you need to adjust the hinges. Otherwise, the fittings are subject to severe wear and tear, and subsequently they will be destroyed and replaced.

The door adjustment is carried out in this way: take a simple pencil and mark with it the places where the door clings to the frame. When such places are identified, the sash needs to be moved in the opposite direction. That is, if the door clings to the frame with the lower right corner, then when adjusting the hinges it will need to be pulled up and to the left. Work must begin from the top loop. As a rule, the top bolt on the hinge is responsible for the vertical movement of the sash, and the bottom one is responsible for the horizontal movement. These are usually 2, 3, or two and a half hex screws.

In most fitting systems, the adjusting bolts are hidden behind decorative plastic caps. To gain access to the adjustment, they must be carefully removed.

The second option for adjusting the door is to shift the center of mass. This is done by moving the glass unit in the desired direction. Carefully remove the beads that hold the glass unit in the door and move it to the side so as to eliminate the sagging of the sash. To keep the glass unit in this position, place plastic gaskets, and then install the glazing beads in place.

When removing glazing beads, be sure to remember their location or mark where they were removed from. Under no circumstances should you confuse the top bead with the bottom or the left with the right - their sizes may differ by several millimeters. Installing a larger bead instead of a smaller one may result in the formation of cracks.

Eliminating drafts

Another type of repair of plastic doors on the balcony that you can do yourself is eliminating drafts. If door leaf set level, but it still blows from the balcony - needs to be changed sealing gum along the perimeter of the door and frame.

This is done this way:

The rubber seal in the door dries out very quickly. So that it does not need to be changed too often, it needs to be processed every six months special compounds on silicone based. You can purchase one from the same company that installed your doors.

When installing the seal, do not tighten it under any circumstances!

You can also eliminate smaller misunderstandings yourself:

If a door handle or lock is broken, it should not be repaired, but replaced.

By the way, about castles

If in your balcony door a lock has been installed (what if?), which does not behave as you would like, you can also fix it yourself. In particular, you can fix problems such as a jammed lock or a broken core.

If the lock sticks:

Remove the plastic lock trim and handle;
Unscrew the fastening bolts of the lock and the core (located at the end of the door);
Remove the lock and disassemble it;
Lubricate the moving parts with machine oil;
Assemble the castle;
Reinstall it and the handle by performing the steps in reverse order.

If there is a problem with the core, everything is much simpler. Repairing it, even if possible, is definitely not cost-effective. Therefore, the “secret” of the lock simply needs to be replaced.

This can be done without even removing the handle or removing the lock from the door leaf:

Open the door and unscrew the core mounting bolt. It is located immediately under the bolt (retractable part) of the lock;
Push the core out of the door leaf;
Install a new secret in its place;
Screw the mounting bolt into place.

These simple manipulations will allow you to return your metal-plastic balcony door to its former functionality and reliability. Remember that in case of more serious damage, it is highly not recommended to undertake the repair of plastic balcony doors yourself. If something goes wrong, you can only make the situation worse. Your unsuccessful attempt may either significantly increase the cost repair work, or lead to the need to replace a broken door.

Repair and adjustment of plastic balcony doors

Plastic balcony doors are made from fairly durable material, and their fittings are of very high quality. But as a result of a long service life, due to natural wear and tear, the mechanisms begin to become loose, the seal becomes less durable, and cracks appear on it. On the surface of the door appear various defects from mechanical influences. This means that the balcony door has become unusable. Many shortcomings can be eliminated by making repairs yourself and without resorting to the help of specialists.

Types of balcony door faults

Before starting repairs, it is necessary to determine the type of malfunction that has occurred. Problems can be serious and can be fixed on your own. Serious problems can only be eliminated professional craftsmen, in this case, the damaged part is basically completely replaced or the door is dismantled.

Such serious malfunctions include:

a crack in the glass of the balcony, in this case it is necessary to completely replace the double-glazed window;
destruction of fittings;
integrity violation welds sashes or frames;
torn loops.

You cannot fix these problems on your own.

Malfunctions that can be resolved independently include:

Problems that arise when opening and closing the door - to fix problems, it is necessary to move the double-glazed window or adjust the door leaf using the capabilities of the fittings;

the doors are not pressed tightly against the frame - the pressure of the plastic doors should be adjusted;
the integrity of the seal is compromised;
the profile surface is slightly damaged (this may be abrasive damage or scratches);
loose handle.
Repairing a balcony door by adjusting the fittings

The most common malfunction of a balcony door is its sagging under its own weight. As a result, it is slightly deformed, but there are no problems with opening and closing it. You just have to lift it a little by the handle. This is not only inconvenient, but also has a negative impact on the service life of such fittings.

Repairing a balcony door begins with making a mark, which is placed in the place where the door leaf touches the frame. The segment where the mark begins to shift away from the straight line is problematic. Repairing a balcony door by adjusting the fittings involves moving the door leaf in the direction opposite to the point at which it touches the frame. For example, if the lower corner of the sash touches the threshold or frame, you should move it in the direction opposite to the corner or up.

Adjustment starts from the top loop. A hex wrench is installed in the slot of the adjusting screw and several turns are made clockwise, bringing the sash to the hinge. After this, the same adjustment is made on the lower loop. In most fitting systems, the top screw helps move the sash up and down, and the side screw moves it horizontally.

Repairing a plastic door leaf using double glazing

This repair consists of the following:

remove the glazing beads that hold the glass unit in place;
using a plastic or wooden spatula, move the glass unit to the side so that the sash disappears;
spacer plastic spacers should be inserted into the gap instead of the blade;
after that, the progress of the door is checked, if everything is fine, the beads are put in place.

You should pay attention to the fact that beads must be installed. observing the position, i.e. the top should not be confused with the bottom, and the left with the right. This is necessary because the sizes of the beads differ from each other by several millimeters, and if you install such a larger part in place of a smaller one, a crack may form.

Replacing the seal

If the plastic door does not close tightly, then the repair will consist of replacing the sealing rubber. Basically, it is changed after several years of use, because it begins to lose its properties. Sometimes the seal wears out due to mechanical damage.

Before repairing the door. you should purchase a seal. the configuration of which is similar to the previous one. Using available tools, remove the old seal from the groove and insert the new seal. It should be rolled out evenly without stretching. At the corners, the seal should be trimmed and additionally fixed with rubber glue.

Plastic door handle repair

Failure of this element results in plastic construction it will be impossible to open or it will constantly jam. The handle may turn very tightly or not turn all the way. In this case, to eliminate the problem, it is necessary to perform a horizontal adjustment of the door.

The latch is a device that holds the door in place. closed position after someone went out onto the balcony. This element begins to wear out over time and may break. Therefore, you need to buy a new latch and install it. It is secured with screws at the end of the door, and in order to replace it, the screws must be unscrewed, the broken latch removed and a new one inserted.

If the connection between the handle and the core is broken, the locking mechanism, handle or latch may fail. To determine the cause of the malfunction, it is necessary to remove and rotate the decorative cover, and then unscrew the fastening screws. Next, you should check the pin that connects the handle and the core. If it turns out that it is cut, then its remains must be knocked out and a new one inserted. If the problem is in the handle, then it is replaced with a new one. After this, the fastening screws are screwed back in. and the decorative cover is put in place.

Conclusion

It is not advisable to repair a plastic balcony door yourself, because only specialists can qualitatively eliminate all the shortcomings that arose during its operation. In case of quite serious problems, when repairs cannot solve anything, you will need to install a new plastic door.

Advantages metal-plastic doors and there is no need to list the windows - they are well known. Among the disadvantages, the most often cited is the inability to repair plastic balcony doors on your own. This is partly true - significant damage can be eliminated only by replacement, but more often we are talking about broken glass or a loose hinge. You can handle this kind of work yourself, armed with knowledge and a simple tool.

To begin with, determine the scope of work

The most common “disease” of any door is rubbing, caused by weakening or displacement of the hinges. In this case, replacement of fittings is required extremely rarely; usually it is enough to carry out adjustment work. Before undertaking the repair of plastic balcony doors, it is recommended to watch a video that clearly demonstrates the upcoming process.

To work you will need:

hex key for the slot of the adjusting bolt (usually 4 mm);
Phillips and straight screwdrivers;
steel hammer;
pliers;
sharp knife;
narrow spatula;
rubber or wooden hammer(for working with glazing).

Repairing a balcony door begins with inspecting the hinges for loose fasteners and checking the diagonals of the door. A noticeable change in the rectangularity of the canvas is rare and can be eliminated by adjusting the spacer inserts that push the glass unit apart. Removing glazing beads for this procedure is discussed below.

If everything is in order with the door and replacement of the seal is not required, proceed immediately to adjusting the hinges.

Adjusting door hardware

Having decided on the direction of displacement and closing the door, move it up and remove the plastic barriers blocking access. decorative overlays.

Modern hinges allow you to adjust the door in several directions:

By rotating the vertical screw of the lower hinge clockwise, the door is raised, and counterclockwise, it is lowered. Access - with the door closed through the upper end of the hinge. The power reserve is usually sufficient to eliminate rubbing of the threshold under the hinge and across the entire width. Rubbing of the far corner of the door is eliminated by adjusting the top hinge.
When the door is open, a second, horizontal adjustment screw is accessible, located at the base of the hinge frame. Its rotation changes the distance from the end of the door to the frame to eliminate rubbing of the end part.
Access to the horizontal screw of the top hinge, located on its door part, is possible only with the door open. By rotating the head clockwise, the upper end of the door is moved away from the frame, and bottom corner the canvas is raised to eliminate chafing.
The tightness of the fabric to door frame Adjustable by eccentrics on the end surfaces of the door. How less distance from the eccentric head to the frame, the tighter the clamp.

If it is necessary to thoroughly disassemble a plastic balcony door, as is the case when replacing the seal, work begins by removing the decorative trims. Then, using pliers, remove the pin connecting the frame and sash parts of the upper hinge. The design of the lower loop allows you to tilt the canvas away from the horizontal and move the upper corner outside the box. Now, to remove it from the lower axle, simply lift the doors. Reinstallation is performed in reverse order. Considering the weight of the product, it is better to do the work together.

Something as simple as replacing or repairing a balcony door handle requires a minimum of time. Access to the handle fastener is closed by a plastic cover, which you just need to pull towards yourself and turn 90˚.

If tightening the fasteners does not help and the cause of the play is in the handle itself, purchase a new one with similar fitting dimensions. Replacing latches and microlifts depends on the specific design and is carried out in accordance with the manufacturer's recommendations.

If there are drafts in the house

Over time, the rubber of the seal wrinkles, loses elasticity and no longer provides proper tightness. In this case, replacing the old rubber cord with a new one will help repair the plastic balcony door. The profile height and shape of the lock must match the old one or be as close as possible to its dimensions. Good feedback has German products. The cord should be taken with a small margin.

A plastic door can be properly repaired only after dismantling it and removing the interfering upper hinge. It is easier to start removing the old cord from the places of the greatest bend - in the corners. The grooves are cleaned of dust and traces of glue at the joint. The new seal for the balcony door is tucked in from the joint - in the middle of the upper groove, and freely along the entire perimeter of the door, without tension or gluing. After cutting in place and aligning the ends, the ends of the cord are glued to the groove and to each other. The seal on the door frame is replaced in the same way.

Self-repair of double-glazed windows

Replacing a damaged glass unit with a new one takes 10-15 minutes, but replacing one of the glass units will take significantly more time and effort. You should know that “branded” double-glazed windows with energy-saving glass, gas injection and other useful options cannot be restored. A double-glazed window manufactured at home is of the same quality as mass-produced inexpensive products. But if one was installed, you can safely carry out the repairs yourself.

It is not recommended to remove glass fragments in the frame - the probability of bending the spacer (distance frame) or cutting yourself is quite high. Only parts that threaten to fall out are removed. Using a knife, wide screwdriver or spatula, remove the glazing beads holding the bag. The blade is driven between the bead and the frame, uniformly widening the gap along the entire length until the lock disengages. It is recommended to start with the side elements. Having freed the glass from the beads, remove the spacer inserts that are pushing it apart, remembering their location. The damaged glass unit is removed from the frame and placed broken glass up onto the table.

In the photo - removing glazing beads using a knife

The outer, hardened layer of sealant (polymer or silicone) on the end surfaces of the bag is cut through thin sharp knife to the spacer frame. The fragments are quite easily separated from the inner adhesive layer (butyl sealant). Large areas separated by inserting a knife between the glass and the spacer. Part of the butyl layer and outer sealant are removed from the plane of the spacer frame freed from glass. The cut is made at a bevel external corner spacer, covering approximately a third of the width of its plane.

Remove splinters and dust from the bottom glass and, if necessary, wipe clean with newspaper using detergents. The inner surface of the glass being laid is also cleaned and degreased. The edges of the folded glass unit are slightly crimped by hand to adhere the glass to sticky layer primary sealant on the spacer. The groove around the perimeter is filled silicone sealant, trying to use all the previously cut space. To harden silicone room temperature 6-8 hours is enough.

Of course, most of these manipulations are not required if you buy a ready-made package. As in the case of individual glass, it is better to take measurements for ordering using the existing glass unit. If this is not possible, measure inner space frames and subtract 3-5 mm on each side for frame deformation and thermal expansion. It is better to purchase double-glazed windows from the manufacturer installed door or a company with good reputation. The new package is installed in the door frame and is expanded with remote plastic inserts.

Installation of glazing beads is carried out in the reverse order - first the short ones, then the long ones.

Steel tools should not be used to press in fragile plastics. A rubber mallet or wooden block no sharp edges. The blows should be applied quite strongly, sliding the tool along the plane of the glass and evenly passing over the entire surface of the bead until it is completely seated in place.

Replacement of glass or replacement of sandwich panels is carried out in the same way. The reason for installing plastic may be the presence in the family small child, for which ordinary glass within reach poses a threat, or economic considerations. For the lower part of the balcony PVC doors this is completely justified both aesthetically and practically. The thermal conductivity of the simplest panel filled with polystyrene foam is significantly lower than that of glass, and there is nothing to say about the weight.

While the door is under warranty, there is a great opportunity to solve problems with the help of specialists from the company that installed the door. By not being shy to ask questions, you can learn a lot from them. Regular lubrication, adjustment of fittings and replacement of the seal will make repairs to the balcony door simply unnecessary and will allow it to far outlast the warranty period.

Reading time: 8 minutes.

The window and door facing the balcony room form balcony block. The structural parts are hermetically connected to each other with a special profile. In addition to providing free access to the balcony and back to the living space, the balcony door should remain a reliable sealed protection of the house or apartment from cold, dust and noise. Its quality functioning is ensured correct selection, installation, configuration of mandatory and additional accessories.

Mandatory door hardware

Loops

Top hinge for PVC doors

This is the most loaded structural element. The hinges ensure reliable fastening of the door leaf to the frame and sufficient rotation of the hinged door when opening it. Door and openable casement in metal-plastic structures they differ in size, but they perform the same tasks. Therefore, for balcony doors, standard anti-corrosion (zinc-aluminum-magnesium alloy) hinges are used, which are also suitable for windows. They can withstand loads of up to 80-130 kg.

Bottom hinge of balcony door

The frame frame and door leaf are connected with hinges during the production of the balcony block according to custom sizes at the manufacturer. Therefore, you will not have to install the hinges yourself and adjust the operation of the door during installation. If during operation after the warranty period there is a need to adjust the door, the following knowledge will help:

Important! If the warranty period of the company that installed and adjusted the balcony block has not yet passed, do not bother self-configuration and, moreover, the replacement of any structural elements.

Sealant

The use of an expensive multi-chamber profile and special energy-saving double-glazed windows does not guarantee that the declared performance characteristics of the door correspond to the actual ones. For the correct “working” of a metal-plastic structure, the role of a conventional seal is invaluable - an elastic band with a relief cross-section profile, which is fixed in special recesses around the perimeter plastic profile doors. At closed door The seal is pressed tightly against the frame and performs the following functions:

isolates the room from noise, drafts, moisture, odors, dust;
protects the room from cold and heat, helps maintain a comfortable microclimate;
saves metal fittings from dangerous condensation.

Modern seal materials are non-toxic, suitable for long-term use, resistant to deformation loads, maintain performance characteristics over a wide temperature range and are almost resistant to ultraviolet radiation. For the production of seals, polyvinyl chloride, ethylene propylene rubber, thermoplastic elastomer, vulcanized rubber (classical rubber), and silicone are used.

Seals are made from various materials and forms

You need to familiarize yourself with the characteristics of various materials and select the necessary seal at the stage of ordering a balcony block or before self-replacement old material. The need for replacement will be warned by emerging drafts, increased street noise, noticeable cracks and other mechanical damage to the sealing material, the appearance of condensation, fungus or mold on the seal. Sometimes problems are eliminated by adjusting the position of the sash and the force of its pressing against the frame. In other cases, the seal is changed.

Replacing worn-out material yourself does not cause difficulties and is performed in the following order:

The rubber band to be replaced is hooked and removed from the groove in the profile along the perimeter of the door leaf.
The groove is cleared of dust.
In the corners of the frame, glue is applied to the groove to securely fix the seal.
A new sealing cord is inserted into the groove along the entire perimeter, and the excess is cut off.
The joint of the seal (preferably located in any corner of the perimeter) is carefully glued.

Door knob

Double-sided balcony handle

To this item door design force is constantly applied, sometimes excessive, to influence other mechanisms. The handle will work correctly and reliably with careful use and timely elimination of emerging problems, which can be easily solved by a caring home craftsman on his own:

Fittings

There is a fitting around the perimeter of the door leaf. Its task is to transmit mechanical force from the handle to the pins, which will block the door in the “closed” position. If necessary, the harness includes “scissors”, with the help of which the function of tilting the door to the “ventilation” position is realized. Replacing fittings is extremely rare and is usually entrusted to specialists from a specialized company. But it is useful to know the sequence of actions for dismantling old fittings to understand the principle of its functioning:

Remove the plastic cover from the top hinge.
The handle is set to “closed” so that the door does not fall in the future. By using mounting handle remove the pin from the top loop.
The handle turns to “open”. Holding the door leaf, we tilt it towards ourselves and lift it until it exits the lower canopy.
The removed door is placed on the floor (the handle is located at the top). The handle is removed first.
All screws are unscrewed around the perimeter.
The central lock in which the handle was secured is dismantled.
Then the middle locks are removed at the bottom and top of the sash.
The corner gears are removed last.

Door leaf body kit new fittings performed in reverse order.

Additional fittings for balcony doors

The presence of these fittings is not mandatory. The decision about their need to increase the functionality of the door structure is made by the owners of the house or apartment.

Opening limiters

These popular accessories can be divided into three groups:

Accessories for organizing micro-ventilation

Micro-ventilation mechanisms

Transfer from wooden structures to metal-plastic is natural. Tightness and high thermal insulation properties plastic windows and doors are the main criteria that determine their choice by consumers. These same qualities become a barrier to the influx into residential premises fresh air.

We must remember! High humidity in the absence of a change in air, it leads to a feeling of general discomfort, reduces the body’s defenses, and causes lethargy. In such a microclimate, ideal conditions for the reproduction of viruses, bacteria, fungi.

Micro-ventilation mechanisms allow you to provide an influx of fresh air at a convenient time and in the right volume.

Multi-stage micro-ventilation system

Thanks to special fittings organize slot micro-ventilation. When the handle is fixed between the vertical and horizontal positions, a ventilation gap of several millimeters is obtained at the top of the folding door (adjustable by the position of the handle).

Another option is to install a climate valve. It can be installed in the door profile at the stage of production of the balcony block or on the profile of a finished structure in use. Such ventilation mechanisms are controlled manually or automatically. They are able to regulate the volume of supply air.

Air valve for micro ventilation

Any fittings require careful use, regular maintenance, correct settings and further adjustment. This will increase the durability of the entire metal-plastic structure and the period of its trouble-free operation.

If you have problems with your balcony door fittings, watch our video:

Today, plastic doors can be found anywhere: in an apartment, private house, office or store. Which is not at all surprising, plastic doors can safely be called unique: they are attractive, affordable, airtight and fit perfectly into any interior.

Stylish balcony door design

However, like any other doors, plastic ones tend to wear out and break. The causes of malfunctions can be very different, which you can solve.

Most of the breakdowns and problems can be fixed on your own, without calling for the help of a specialist, especially without spending your own money on him.

But don't forget about warranty period: if it has not yet expired, be sure to contact specialists who will solve any problem professionally, efficiently, and most importantly, free of charge.

Today we’ll talk about problems that you can solve on your own.

What can happen to the balcony door?

If you notice problems with your balcony door, you should figure out what happened. You shouldn’t start repairs right away: every problem definitely has its own solution, so you shouldn’t “dispossess” the plastic door.

Repairing a plastic balcony door with your own hands is real

First, let's define a specific problem:

door fittings are broken;
the door was askew;
the door seal is worn out;
the door hinges sagged under the weight of the balcony door;
the shape of the sash has changed;
the door sagged.

We are confident that you can solve all these problems quickly and easily.

Of course, in case of cracks in the glass, cutting off hinges, serious damage to the frame and welds, you will have to contact a specialist immediately, and without hesitation. Fixing such malfunctions yourself is fraught with even more serious consequences.

Balcony decoration is an important part of the interior

Signs that a plastic door requires careful inspection and repair:

the door began to touch the frame;
the door handle began to act up: the door does not close or open well;
you began to feel cold near the door or real drafts in the house;
To close the door tightly, you have to lift and press the door, applying force.

You need to conduct a thorough inspection of the door, check its level and the operation of the fittings. Having identified the breakdown, proceed to repair it according to our instructions.

How to replace the seal of a plastic balcony door?

If you begin to feel a loss of heat in the house and the appearance of drafts, the balcony door has lost its tightness. Seal wear is one of the causes of this problem.

Repair of a balcony door must be carried out strictly according to the instructions

Seal replacement procedure:

First, buy a new seal for a plastic door in the store. Check it well for cracks and damage. Best manufacturer Germany is considered to be the manufacturer of rubber seals. A cheaper seal will have to be replaced after about four years.
Also in the store buy high-quality glue for attaching the seal.
Carefully remove the old one rubber compressor from the profile of a plastic door.
Thoroughly clean the door grooves from any remaining adhesive, particles of dirt or dust. Wait until the door is completely dry from moisture.
Lubricate the grooves with glue along the perimeter of the profile.
Install the seal from the top corner, going down, do not stretch the cord or press too hard.

For longer-term and functional operation, the rubber seal can be lubricated with a special product.

How to repair door handles?

The handles of plastic doors break quite often, because they are subject to a high load.

Is your balcony door starting to act up? We are repairing!

More often than not, they simply become loose – it’s not a big deal. You just need to remove the decorative trims from the handle and tighten the screws.

If the handle or locks are broken, you should not repair, but completely replace the door handles.

The problem of faulty door handles is the most common problem and the easiest to solve.

What to do if the plastic door is sagging?

Often the reason for the sagging of a balcony door lies in its own heaviness. Sometimes the hinges simply cannot support the weight of the balcony door, causing them to sag.

You need:

Open the door. Place it in the swivel position.
The top hinge has a screw that you need to turn clockwise. Use an adjustment wrench. Once you pull the sash towards the hinge, close it.
Also lift the bottom hinge flap using the key.
The sash must be lifted so that it does not touch the frame with its edge.

Once you have lifted the door, be sure to check how easily it closes and opens.

What to do if the balcony door begins to touch the frame?

If your door begins to touch the door frame, this means that the sash has moved. To fix this problem, you need to move the sash a little closer to the hinges.

You need:

Take the adjusting wrench and use it to turn the side screw, which is located at the bottom hinge, until the lower corner of the sash is pulled into the desired position.
Adjust the top screw in the same way by turning it clockwise. After all manipulations, close the sash.

Experts say that this work is quite enough to adjust balcony doors. Otherwise, call a specialist.

What to do if there are scratches or abrasions on the plastic door?

We're talking about small things mechanical damage, which can appear completely accidentally and even unnoticed.

In this case, the plastic door requires minor cosmetic repairs.

In the production of plastic doors, there is a special glue that helps eliminate any door defects.

After treating the plastic door with special glue, wait until it dries. Then sand the surface of the door with fine sandpaper and apply special solvent For plastic surfaces and paint it.

Unfortunately, not all materials can be found in our construction hypermarkets, so we recommend contacting the manufacturer directly or a professional distributor.

As you have seen for yourself, repairing plastic doors does not take much time, effort and money. And having experience in repairing balcony doors in your arsenal will never hurt, but will even help a lot and perhaps even save you. critical situation. So don’t hesitate and don’t doubt, and we will be happy to help you with this!