The best ideas for DIY crafts made from plastic bottles for your garden. DIY country crafts from plastic bottles

A plastic bottle is not just ordinary waste (garbage), it is a decorative option, if used skillfully. Bottles, depending on the liquid stored in them, vary in shape, color and size. These features will allow you to do interesting crafts from plastic bottles for a do-it-yourself dacha.

Massive buildings

Plastic bottles are used in this case as a substitute various materials all kinds of designs. They can replace bricks and even slate. To provide the necessary strength, the bottle is covered with sand, and in order to achieve a certain shape, use pressing and scissors.

Gazebos, greenhouse buildings

The essence of the building is PVC installation products using fastening materials in the form of wires or ropes. Ultimately, when using sufficiently strong frames, decent supporting walls for any structures emerge.

Enclosing elements

The principle of the craft is the same as in the point described earlier. It is also possible to decorate an existing fence or gate using plastic bottles, cutting them, and gluing mosaics.

Awnings

The structure can be used by you as a shelter from the rain. You can hide not only yourself, but also leave your car or equipment behind. To build it, you need to install a strong frame onto which bottles are attached using wire.

Water heater

With proper construction and combination of containers, you can make Summer shower, the water of which will heat up in bottles under the influence of sunlight.

Plastic furniture

Using bottles you can make outdoor benches, chairs, and even sofas that can be upholstered for greater comfort.

Shades for lamps

Use bottles made of heat-resistant plastic. You can make a lampshade of any shape and color, depending on the design of your summer cottage and the requirements.

Flower pots

Usually bottles act as containers used for initial planting, but with skillful processing you can get beautiful pots and flowerpots.

Flower beds made from plastic bottles

By subjecting the bottle to physical processing in combination with other fastening materials, for example, stones, you can mount an exquisite flower bed and, if necessary, paint over the resulting products.

Birdhouses

Hanging products from bottles for bird feeders are made with just a couple of cuts in the base of the bottle. At additional processing, the feeder can look quite aesthetically pleasing.

Home decoration

All kinds of animal shapes, lanterns and even curtains can be made with a skillful hand.

boats

With a certain number of bottles and a couple of video lessons, you can make your own boat and go fishing.

Playgrounds for children

It is possible to cut out figures, slides, for plant lovers - artificial palm trees, flowers and much more.

Children's slide made of bottles

Installations for land cover

animal figures, aircraft and much more. The most popular crafts and instructions for making them are described below.

Swans-pots

In order to do original design in the form of a swan, we need a certain number of large bottles (5-6 approximately, depending on the size of the bird), as well as:

wire made of copper or any available metal;
putty (finishing);
metal grid;
tight-fitting material (bandages, gauze);
knife (for shaping);
spatulas of various sizes.

Swan from bottles

Step-by-step production:

Cut a large bottle lengthwise, do not try to make two identical halves, this is completely unnecessary for the craft. The approximate shape resulting from such an operation should resemble a voluminous flowerpot. Next, add wet sand in order to achieve the desired deformation of the bottle.
We attach the wire to the lid, having previously made a hole in it. To make this process easier, you can use a heated nail or hand drill. The wire will become the bird's neck in the future. We throw the diluted putty onto the prepared polyethylene bedding in a layer of 5-6 cm. Place the bottle of sand discussed in the previous paragraphs on the resulting kind of foundation. Using a spatula and mortar, shape the swan's body into the required shape.
Give the wire a curved shape, reminiscent of a neck. Attach the knurled ovals of putty to the wire and secure everything tightly with gauze or bandage. The transition from the base of the swan to the neck should not be abrupt, otherwise the design will not be aesthetically pleasing. At the end of the wire, make a head out of putty by adding eyes and a beak.
We attach the metal mesh to the body using a solution and get wonderful wings. The solution is applied to the mesh and the result should be wings of the shape you choose. The process is quite painstaking, so be patient and strong. Using spatulas, create the curves of a swan.
After drying, sand the resulting product with emery cloth. The next step is to prime the bird and paint it, not forgetting to draw all the attributes of the swan's face.

cacti

Enough original idea and very easy to install. Using wire, we make the base of the cactus and fix it in the ground. Afterwards, we put on the bottles of the required shape and color.

Cacti from plastic bottles

Flowers

For the manufacture of plastic flowers we need to have:

knife and scissors;
bottles of the required shape and color;
paints and varnish for finishing works.

Step-by-step manufacturing instructions:

Cut off the top of the bottle. Next, we make several cuts to the base with scissors. One stripe should be wider than the next three, since it will represent the petal, and thin stripes will play the role of stamens.
Larger strips are cut with scissors, giving them a sharp shape. Thin strips are twisted and bent down using a knife.
Petals - wide stripes are painted with green paint or varnish.
The stand is made from the remaining material by cutting the bottle in half, not reaching the bottom 4-5 cm. The middle of the bottom remains intact. Give the workpiece the appropriate shape and place it on the ground.

Owl made of disks and bottles

Necessary materials:

bottles of different sizes (2 x 5 liters and 40 x 2);
special glue (epoxy);
screws for fastening;
discs and beads for eyes;
knife and scissors;
foam for framing.

Manufacturing instructions

The outlines of the future face are organized by cutting it out of foam plastic; also allocate places for the eyes. Using packaging from button batteries we make eyes. Place the beads inside the empty package and pour epoxy glue into it. After drying, the eyes are attached to the head. If desired, you can glue regular CDs in front of the beads, which will give your eyes a more interesting look.
Having chosen a bottle of a dark color, a beak is cut out of it, which is then attached to the head in Right place. The rest of the bottle is not thrown away; feathers can be made from it. After cutting, the feathers are glued along the back of the eyes. Eyelids are cut out of the remaining plastic, which, when glued, should cover the places where the feathers are attached.
The next step is making the wings. Taking a large bottle, use it to create a frame for the wings; pre-cut feathers from a two-liter bottle are attached to it. When gluing the feathers, you must cover the neck of the large bottle. Afterwards, attach smaller feathers in several rows, and the last row Using a knife, bend it over the base of a large bottle.
Using the second large bottle, make the base for the owl's body along with the back of the head. The body is covered with feathers in several rows, as are the wings. The part that should not have feathers is the back; the rest is covered with feathers in random order.
Using self-tapping screws, we attach the resulting parts (head and wings) to the owl’s body. Before doing this, cover the back of your head with cutouts from the middle of the bottles. The joints are also covered with feathers. After securing all the parts, paint the owl in the desired color.

bottle pig

Necessary materials:

bottles different sizes(one 5-liter and 4 one and a half liter);
arakal color of future eyes and nose;
nails for fastening;
knife and scissors;
paints or markers;
pen or pencil;
paper.

Manufacturing instructions

One and a half liter bottles are cut diagonally to remove the neck. The cut off part will be used for hooves in the future. Draw eyes, ears and nose on paper. Using a marker, move the drawn outline onto the arkal. The part of the bottle that remains after cutting is used to organize the ears. Cut a tail from any bottle and shape it into a twisted shape using a knife.
After marking the future attachment points for the ears, hooves and tail, use a pre-heated nail to make holes. The parts are cut at the fastening points and at the joints the resulting edges are bent for greater strength.
The last stage is painting the pig. After it dries, glue on the eyes and nostrils. Paint the hooves black. The piglet is ready, you can install it in a flowerbed or anywhere in your summer cottage.

Palm trees

Necessary materials:

bottles desired color(green and brown);
knife and scissors;
copper wire or rod.

Manufacturing instructions:

Cut the bottle in half and make jagged cuts on the top. Prepare as many pieces as possible, as the palm trees must be large.
A metal pin or thick wire is attached to the ground. It is necessary to ensure the reliability of the fastening so that the structure does not fall in the future.
Plastic blanks are strung on a pin and bent for a more natural structure of the palm tree.
Green bottles are needed for branches and leaves. Using scissors, the bottom is cut off, and the rest of the part takes on the desired shape using cuts. The shape of the leaves can be any, it all depends on your imagination.
The last stage is securing the leaves to the pins and connecting all the parts into a common structure. In order to fasten everything together, you can use welding or ordinary harnesses, which can be purchased on the shelves of any hardware store.

Flowerbeds

Necessary materials:

cement and sand;
crushed stone or gravel;
tire or barrel cut in half;
bottles (can be glass).

Manufacturing instructions:

Place the blank in the place of the future flower bed.
Prepare a solution (mix cement with sand in a ratio of 1:2, gradually adding water).
Coat the workpiece with the solution (the layer should be quite dense) and insert the bottles with their necks into the solution. When inserting bottles, follow a checkerboard pattern.
After hardening, pour gravel or slag onto the bottom of the workpiece to organize drainage. Afterwards, fill the flowerbed with soil. The structure is ready, now you can plant it with any flowers you want.

Crafts from the bottom (bottom) of a bottle

The bottles are cut (the lower halves are used for work). The color scheme can be any to your taste. After organizing a mound of soil so that it becomes a slide required diameter, blanks from bottles are stuck into it. With a dense arrangement of bottles and the right color, original plastic buildings are obtained.

Ladybug made from bottles

Decorating garden beds

In order not to waste time on solid plastic crafts, you can simply decorate the area by making contours for the garden or paths using plastic bottles. The bottles are cut, the neck is removed to the narrowing point, filled with sand or earth and dug in along the contour of the bed, flower bed or plot.

Decorating a garden bed with plastic bottles

If necessary, the bottles are painted, which gives your frame an even more aesthetic appearance. This type of decor is quite diverse, since it is possible to organize any shapes and colors according to your desire.

Flowerpots

Hanging pots or just mini flower beds can be easily made from plastic bottles. By cutting off the top, we get a straight pot, by cutting off the bottom - cone-shaped, or the middle - for hanging models. Afterwards, the workpiece is filled with soil and the plants you need are planted in it. Bottles can be painted or left transparent. You can install pot models along the path or decorate the fence with hanging plant pots.

Bottle fence

Making a fence is, in principle, simple; such a construction is very economical and will allow you to protect the area from the penetration of animals and other unwanted guests. For construction, pins are used, firmly fixed in the ground, on which plastic bottles are strung.

Bottle gazebo

In the presence of required material and free time, you can make a gazebo. For the base of the gazebo you will need a lot of wire and rods. The foundation can also be made from plastic bottles filled with sand or soil. If desired, the gazebo can be covered with protective fabric or tarpaulin. The bottle components can be painted and easily replaced at any time.

Trap for bloodsuckers

To make a mosquito trap from a plastic bottle, you will need a two-liter container, which is then cut in half. The upper part is turned over and inserted into the lower one, creating a funnel, and the lower part, in turn, is filled with sweet water. Then the entire workpiece is darkened by painting or gluing. The trap is ready. To attract flies and wasps, you can add a little jam, honey or syrup to the container.

Scheme for making a mosquito trap from a plastic bottle

Scarecrow for moles

For this craft, make three cuts in the bottle and bend the plastic so that you get blades. Place small stones at the bottom of the bottle, and place the bottle itself on a rod buried in the ground. In the presence of minimal wind, the structure will produce sounds that are not tolerated by moles.

Mole scarer made from plastic bottles

Irrigation structures

Bottles can also be used for watering plants in your summer cottage. Uniform watering can be organized in several ways. An option is to cut the bottom of the bottle and bury its neck in the ground. Before burying the neck, a hole is made in the lid, and grass is placed at the bottom of the hole to prevent the lid from clogging with soil.

You can also cut off the bottom of a plastic bottle and hang it over a flowerbed or in the desired area of plantings. In this case, watering will be carried out through the neck of the bottle with the lid loosely screwed on. Watering is regulated by tightening the plug more or less.

Crafts from lids

When working with plastic bottles, there may be a fair amount of cork left behind. Using them correctly can give them a second life and help avoid the recycling process.

Curtains made from lids

Organization is very simple, using a drill or thin nail, holes are made in the lids different colors and with the help of fishing line the elements are attached to each other and to the cornice.

Paintings from traffic jams

Having some experience and a sufficient number of covers of different colors, you can create a wonderful decor for any surface.

When working with bottles of any size or color, make sure they can withstand weather your climate region. Before carrying out any operations, take care to remove the labels from the surface of the bottle.

Conclusion

Plastic bottles and caps do not have to be thrown away after their direct use; they can be indispensable decorative elements for your dacha. After reading this article, you will be convinced of sustainable recycling plastic containers and you can make them good crafts with your own hands.

The more reverently we treat our site, the more pleasure we strive there not only for work, but also for relaxation. When we decorate a garden plot with our own hands, it becomes even more familiar and attractive. This can be done with the help of original figures made from the simplest and available materials, for example, from plastic bottles. Indeed, plastic is easy to cut, model, paint and retain its shape for a long time. The main thing is to show your imagination and devote some time to work. The following are possible options figurines that are appropriate for any garden plot.

Palm

Making palm trees from plastic bottles is a fun and easy process. Therefore, a large number of summer residents decorate with this exotic plant your site. If you want to join their ranks, stock up on a large number of plastic containers of different sizes (preferably from 1.5 to 2.5 liters) in brown and green shades.

Trunk

The wings consist of two parts: the upper one is assembled from small feathers cut from the bottoms; the lower one is more difficult to manufacture. First you need to cut out the middle part of the bottle, cut it into two parts, and then each of them into rectangles same size.

Using scissors, the bottle is cut according to the marks made, while the neck remains in the upper part - it is necessary to secure the swan's neck in the hole.
The neck frame is made from a hose with wire. It is pushed into the neck and given the desired shape.

Feathers are cut from a small plastic bottle. To do this, the bottom and neck are cut off, and feathers of any desired shape are made from the remaining cylinder. It is best to cut the edges of the feathers a little in the form of a fringe, and then outside Warm each feather with a candle.

The feathers are collected in twos and secured with wire.
For the neck, it is best to use small bottles without a bottom, which are threaded onto the hose upside down. You will need at least 15-20 of them.
At the place where the hose ends, you need to make 2 holes in the bottle and the hose itself. Pull the wire through the holes and secure it.
The beak itself is best made from a large cap (usually bottles with chemicals). The cap must be cut into 2 parts so that a shape resembling the letter “M” is obtained. The finished beak should be painted.

Finally, your favorite plants should be planted in the finished swan.

Making swans from plastic bottles is a process that requires care and precision. But the result is a very cute and practical craft.

Christmas trees

Of course, almost every garden has living trees, but this does not mean that there is not a little place for a beautiful “artificial” Christmas tree. It can even be decorated during the New Year celebration at the dacha.

It is necessary to prepare in advance plastic bottles of different sizes - 2; 1.5 and 1 liter. For a Christmas tree about 1.2 meters high you will need at least 35-40 green bottles, washed and dried. To make it you will also need scissors, a candle, and a pin.

Manufacturing process:

Cut off the bottom of each bottle, cut the side walls into strips about 1.5 cm wide and round their ends. Coniferous branches will look even more interesting if you melt them a little with a candle at the same pitch (about 2 cm).

To build a tree trunk - for this it is best to strengthen an iron rod in the ground.
Attach the branch to the base: simply string 2-liter bottles onto the trunk, bottom down, then 1.5-liter bottles, and 1-liter bottles on top.

If containers of the same volume are used, then after assembling their branches can simply be trimmed so that the tree turns out to be cone-shaped. The lower branches must be straightened, and the upper ones can be left in their original position.

That's all, the Christmas tree from a plastic bottle is ready.

Lamb

In 2015, it’s simply impossible not to decorate your country cottage area symbol of the coming year - a lamb. It will surely bring good luck to the whole family. Creating such a figure is quite a large-scale undertaking, but the result is impressive.
To work you will need:

Plastic bottles: for legs – 4 pcs. 1.5 l and 4 pcs. 2 l each; for the body – 7 pcs. 2 l each; for the head – 3 pcs. 1 l each; for a fur coat - about 20 pieces, 2 liters each (it is important that they have figured bottoms).
The wire is best copper.
Aerosol paint (white and golden).

A sheep made from plastic bottles is made in the following sequence:

The necks of two 2-liter bottles are cut off, and their bases are inserted into each other. Long but narrow ears are attached to them using wire.

2-liter bottles are connected as the body and neck. First, the base is made, and then other bottles are attached to it using wire or tape.

The head is attached to the neck.
The lower part of the legs is made from 1.5-liter bottles, and the upper part is made from 2-liter bottles. The legs are tightly fixed to the body with wire so that the sheep does not dangle on them.

The curly bottoms from 2-liter bottles are cut off and connected to each other with wire. This creates a sheep's coat that covers the body. It is attached to the stomach.

The easiest way to make eyes is from corks.
The finished sheep can be painted with white spray first, and then a little gold paint is sprayed on top of it.

Such a sheep will look simply wonderful in the summer surrounded by greenery and flowers.

Penguins

A penguin craft made from a plastic bottle is a cute and funny creature that can be used to decorate both your home and garden. This figure is quite simple to make, so your children can become full-fledged assistants in this process.
To make penguins you will need:

2 plastic bottles of 2 liters;
yellow, black and white paints, as well as a brush for them;
pompon;
braid;
glue (it’s good if you have a hot glue gun).

Manufacturing process:

The bottles are cut crosswise into 2 equal parts.

The lower parts are used. They need to be inserted into each other. The halves can be fixed with glue, but even without it the parts are held together quite firmly. The bottom of one bottle functions as the head, the bottom of the other serves as the penguin's paws.
Next you need to decorate the penguin figurine - first in the basic White color, and then use black paint to depict the characteristic penguin toe. The hat can be made in any color (in our example it is blue). To bring the penguin to life, he needs to draw eyes and a nose.

DIY crafts from plastic bottles will diversify your garden landscape and will also become good helpers summer residents in their difficult but exciting work.

Let's start with the simplest, but very useful crafts from plastic bottles. You can make a garden broom, dustpan and plant pots with your own hands.

Country broom and dustpan

Making this craft from plastic bottles with your own hands will take you no more than 20 minutes, and the result will delight you for a long time, especially during the autumn leaf fall season. You will need:

4 plastic bottles with a volume of 1.5-2 l;

a long wooden stick for attaching a broom;

glue "Moment".

Progress

1. Cut off the bottoms of 3 plastic bottles.

2. Insert the cut bottles into each other and, using scissors, cut from the bottom to form a “fringe” - these will be the twigs of the panicle.

3. Use a knife to adjust the diameter wooden handle to the diameter of the bottle neck.

4. Insert the handle into the neck of the bottle and secure it with Moment glue for strength.

5. Cut the bottom of the 4th plastic bottle and cut out half the middle - this will be the scoop.

Self-watering plant pots

This DIY craft from plastic bottles will make caring for seedlings much easier.

You will need:

2 liter plastic bottles;

thick lace;

stationery knife.

Progress

1. Cut a plastic bottle in half by unscrewing the cap.

2. Punch a hole in the middle of the bottle cap using an awl.

3. Cut about 7 cm of lace and fold the piece in half.

4. Thread the string through the hole and secure it to the lid with a knot. This cord will conduct water from the lower section for irrigation to the upper section, in which the plants will be planted.

5. Screw the cap to the neck of the bottle and, turning it upside down, insert the top part into the bottom.

6. Fill the bottom of the bottle with water.

7. Place soil in the upper part and sow seedlings.

8. After planting the seeds, water the ground; the plants will receive water from the lower compartment along the cord.

Kittens and piglets

Making crafts from plastic bottles with your own hands is doubly enjoyable if you have little helpers to help you. You can involve children in working on your garden landscape by inviting them to make figurines of funny animals.

You will need:

wide plastic canisters for water volume 5 l;

plastic bottles with caps;

Oil paint;

glue "Moment";

stationery knife.

Progress

1. The body for the piglet or kitten figurine will be a 5-liter canister with a lid.

2. Make the legs from bottle caps, attaching them with glue to the lower part of the “torso”.

3. From plastic bottles, cut out blanks for the ears, tail and, when working on a kitten figurine, a mustache.

4. Attach the whiskers, tail and ears by making proportional slits in the 5-liter canister.

5. Color the figure as you wish.

Using a permanent marker, you can make the cutest flower pot in the shape of a cat from a painted five-liter canister in a couple of minutes.

Princess Frog

And this DIY craft from plastic bottles can become the talisman of your site. Place the beautiful frog in the brightest flowerbed - in a place of honor.

You will need:

2 plastic bottles of 2 liters;

paint for external finishing works in a can, oil paints;

additional decorative elements at your discretion - beads, rhinestones, ribbons, etc.

glue "Moment";

stationery knife.

Progress

1. Cut off the top part of the bottles, making a kind of pots about 15 cm high.

2. Take the 2 lower parts and insert one into the other, connecting them with cuts so that you get a barrel.

3. From the remaining pieces of plastic bottles, cut out the front and back legs of the frog.

4. Attach the front legs to the base of the barrel blank using Moment glue.

5. Place the hind legs in the appropriately sized slots, previously made stationery knife on the side walls of the barrel.

6. Paint the frog's body green.

7. Draw the eyes and mouth.

8. Make a crown from scraps of plastic bottles, decorate it and attach it to the frog’s head with glue.

From a plastic bottle and pine cones you can make another cute garden inhabitant - .

Many homestead owners create all sorts of products from plastic bottles to decorate their place. You can create real works of art by spending a minimum of money.

Not only decorative items are made from plastic, but even furniture. All you need is a knife, an awl and a little imagination.

In this article we will look in detail at how to make crafts from plastic bottles with your own hands.

Decorating the site

Which ones homemade products you won't see on personal plots. There are flowers, animals, and trees. You can create beautiful sculptural compositions, which will not only decorate the garden, but will also give a great mood.

Let's look at a couple of instructions for beginners that will help you easily create crafts from plastic bottles. It will be a palm tree and a pig.

Bottle palm

To make a palm tree you need to create a frame. Its length should be equal to the height of the tree.

Take bottles of the same size, cut off their bottoms and place them on top of each other. Then the leaves are cut out. They are attached to the top of the created structure. When everything is ready, the palm tree is painted green.

Funny pig made from bottles

The pig will look great anywhere in the garden. To make it you will need:

5 liter bottle;
four bottle necks for making legs;
one top part from a bottle, which is cut into two parts to make ears;
wire for tail;
two beads for eyes;
glue;
pink paint.

The parts are connected and secured with glue. Ready product needs to be painted. You can take oil or spray paint. To prevent the piglet from being blown away by the wind, you need to pour sand into it.

Besides decorative function the structure can serve as a flower bed. To do this, the top is cut off, filled with soil and flowers are planted.

Crafts made from plastic bottles for the garden can serve as flower beds, borders or paths. To make a path, bottles are inserted into the ground with their necks.

Both whole and cut plastic are used. It is important to fill the bottles with soil so that they do not become deformed when they are walked on.

Use of bottles on the farm

Bottles are used not only for decoration. These can be used to make a dustpan, washbasin, or pest trap.

Undoubtedly, everyone needs a container for storing some items. To make it, just cut off the neck.

The washbasin is also very easy to make with your own hands. The bottom of the bottle is cut off and holes are made through which the rope is threaded. The structure is hung in the desired place and water is poured. To wash your face, just unscrew the cap a little.

To make a trap, you need to cut the container in half. To catch insects, some kind of bait is placed at the bottom. For example, sugar syrup with yeast is suitable for this.

Will need hot water, in which sugar and yeast will dissolve. The cooled liquid must be poured into the trap. Not only flies and wasps, but also mosquitoes will flock to this delicacy.
Note!

Even a child can make a scoop. First you need to outline its shape and then cut it out.

Can be made from plastic flower pots, greenhouses or containers for seedlings. Descriptions of such crafts made from plastic bottles can be found on the Internet at large quantities, but to create something unique, you need to show your imagination.

It is fashionable to build a self-watering device from plastic containers. To do this, cut the bottle, make holes on the sides and insert the hose into the neck. With the help of such a device, the plants will be perfectly hydrated.

For plants that do not like surface watering, make the following device. The bottom of plastic containers is not completely cut off. A trench is opened on the side of the plant where stones are placed. The bottle is buried upside down.

Then pour required quantity water for irrigation. You can place the bottles upside down, but in this case you will need to make holes in the container.

Use plastic container and for heating plants. To do this, bottles are filled warm water and place them around the plant.

Note!

For inspiration you can look various photos crafts from plastic bottles. You don't need to put in a lot of effort to make original decoration or a useful item for your garden that will last for many years.