A modern country house is designed to provide the best living conditions. Currently, all conditions have been created for this - abundance constructive solutions in house construction, a variety of traditional and new proven materials.
One of the elements of private buildings is currently a terrace - a fully or partially open area equipped with a roof. It allows you to fully feel like a part of nature, practically without leaving your home. What materials and in compliance with what requirements can be used to finish the terrace will be discussed further.
Users often search:
Classic terrace design
Structurally, an extension to a house, called a terrace or veranda, is a podium raised above the ground on one of the types of foundations, and a roof made of some material, supported by several support beams. According to their design, such structures are divided into:
- open;
- partially closed;
- closed.
Open veranda
This view is good when located on the leeward sunny side. Due to the absence of fences, there are practically no boundaries between the veranda and the space surrounding it. It is better if the floor height of such a structure is low. This is especially true when children live in a country house.
Photo: 3D project country house with veranda
Due to the lack of complete isolation from the atmosphere, the operation of structures of the first and second types is possible only in the warm season. It is impossible to properly insulate them due to the design features, and it is quite difficult to completely protect visitors to such a terrace from the wind and raindrops flying inside.
Closed terraces
This type is most suitable for year-round use as an additional room. Even in the winter cold, closed from the wind and frost, you can enjoy hot tea while admiring the beauty of nature. In this case, it is better to combine the interior decoration of the veranda with insulation of all its walls. This will minimize heating costs for the house as a whole.
Veranda finishing options
The manufacturing process of the described structures is not complicated and is quite accessible with your own hands, as is finishing the veranda inside or outside. Since the topic of the article suggests more detailed introduction With the second part of the work, we will consider them, focusing on possible options, their features, advantages and disadvantages.
Currently, the interior of the veranda is covered using the following materials:
- wooden lining;
- plastic panels;
- MDF panels;
- cement plaster and cement-based artificial stone.
Decorating the veranda with wood
The classic option is the use of natural wood materials for wall decoration not only interior spaces houses, but also outbuildings. The lining is distinguished by its good appearance, ease of installation and low requirements for the quality of base preparation.
Its installation is carried out on a lathing made of 40x40 mm bars using special fasteners - clamps, which grab the panels by the groove and securely fix them. Finishing parts can be placed vertically, horizontally or at an angle to the floor.
Thematic material:
When finishing the exterior, you can sheathe the veranda only by installing the lining parallel to the soil with the ridges up to prevent the accumulation of water in the grooves.
Plastic finish
Also quite a common option. It is better to decorate the veranda with such panels closed type. In this case, temperature changes are less sensitive to the material, which helps to increase its service life.
Unlike wood materials, plastic is practically not afraid of water. Modern retail chains offer many options for both color and texture design. plastic panels.
Installation plastic trim easier than wood. Thanks to the considerable width of the panels, the process is faster.
It is convenient to attach finishing parts to the sheathing using construction stapler, driving staples into a wide shelf along the edge of the products. Plastic panels do not require further finishing with paintwork, they can be easily washed with a damp cloth, and dust does not settle on them.
Interior finishing with MDF panels
Another common finishing material for interior works– MDF panels. Like the previous option, they are distinguished by a large working width, which allows for sheathing to be carried out quite quickly. For fastening to wooden sheathing, clamps are used, similar to those used when installing wooden lining.
Thanks to a large number colors imitating natural wood, stone and even leather, such interior decoration of the veranda will have a very quality look. With all its advantages, MDF also has a significant drawback - very low moisture resistance. In this regard, it is better not to use them for finishing open terraces. Otherwise you will need additional protection in the form of varnishing all sides of the panels.
Decorating veranda walls with cement materials
In the case of using cement-containing materials for the manufacture of terraces building materials– blocks with one or another filling, or bricks, it is better to finish the walls with mixtures or details that are similar in composition.
Please note that gypsum-based plaster and gypsum artificial stone are not suitable for covering the walls of open verandas.
Often home owners are stopped by the high cost of cement finishing materials. At the same time, it is not difficult to produce the required quantity of original artificial stone independently in a home workshop. By adding aniline dye, you can get a unique interior in the room being finished.
Polycarbonate for finishing terraces
As already noted, the materials listed above, used in finishing the interior space of verandas, have certain disadvantages that limit their use. IN last years increasingly wider external walls and the roofs of the terraces are covered with polycarbonate - artificial transparent material, allowing you to get a closed space while maintaining visual contact with the surrounding nature.
There are two main types of this plastic:
- Cellular. It is characterized by minimal weight, high light transmittance, and durability, therefore it is often used for roofing terrace roofs.
- Monolithic. Its properties are close to real quartz glass, but unlike it it does not have such high fragility. This determined its use in vertical frame structures - windows, doors, transparent walls.
Modern manufacturers are not limited to producing colorless sheets. To create a soft shadow, we recommend using green, blue, red, yellow cellular polycarbonate for the roof. You can combine several colors, giving the entire design brightness and uniqueness.
Covering veranda walls with cellular polycarbonate is quite easy to do yourself. To work you will need a minimum set of tools:
- cutting knife - any construction knife will do;
- screwdriver
The polycarbonate installation technology involves the following list of works.
The installation of cellular polycarbonate on the roof of the terrace is carried out in a similar way. If there is a ridge - the junction of two roof slopes, use a special ridge profile, sold in organizations that sell sheets.
In the absence of cutting experience, cutting sheets to the required sizes can also be done by workers at construction bases.
As follows from our review, the amount of materials for covering terraces is sufficient to create a unique structure. Before finishing your veranda with any of them, carefully study all the operating features in a particular case.
The veranda should be as comfortable and aesthetically pleasing as the entire building. This could be the front entrance, which gives the first impression of the interior, or an extension intended for recreation or household needs. One way or another, one of its main purposes is to serve as decoration, without which the house would not look so elegant. It can be designed in the same style as the main building, or differ from it, creating an interesting composition with it and successfully complementing the facade. The walls and ceiling will require a durable and fireproof finish, so we’ll tell you what you can use to cover them. unheated veranda outside and inside.
How to cover an unheated veranda inside and outside
Material requirements
One of the main tasks is to create a coating that does not allow heat to pass through and protects from drafts. The walls must breathe, otherwise during the cold season it will be stuffy and uncomfortable inside, especially when the radiator is on. A vent valve may solve the problem. Such devices are usually used in city apartments where impenetrable plastic double-glazed windows are installed.
If the house is intended to be lived in all year round, the covering will be required to have good thermal insulation properties. It is advisable to put a layer of thermal insulation under the finishing, covering it with a film that does not allow moisture to pass through. Without such protective measures, water will penetrate into the voids and begin to destroy the material, expanding when it freezes. There will be a damp smell in the room, and mold may appear in the corners.
If the building is garden plot used only in summer, the outer finishing layer must still have good waterproofing properties and reliably protect brick, concrete or wood from getting wet.
One of the most important requirements- fire safety. For a log house or structure made of timber, relaxation can be allowed, but it is still worth making a choice in favor of a non-combustible coating. In the event of a fire, it will retard the flames and may save the lives of people in the building.
Important qualities are environmental friendliness and non-toxicity. The coating should not cause allergies. If it has a strong chemical smell, it should not be used under any circumstances. Even in open space It will be impossible to get rid of such a “flavor”. When burned, the material will likely release toxic gas. Unscrupulous manufacturers try to sell their goods as quickly as possible. It is usually sold in markets where no one monitors the quality, and is very cheap, so it is better to purchase it in construction stores, where the quality of the product is beyond doubt. Price serves as one of the indicators of quality.
The cladding is required to maintain its properties despite frost, rain and exposure to ultraviolet radiation. If you plan to paint it, it is better to choose the most durable compounds.
How to properly finish the inside of the veranda?
A veranda or terrace in a private house is an excellent place for its inhabitants to relax.
To make it comfortable and create an atmosphere home comfort and peace, his interior design needs to be given the appropriate look.
The most commonly used material for constructing a veranda is wood. And before you start decorating the veranda, you need to wood parts cover with an antiseptic solution.
It must be taken into account that this is a non-residential and unheated room, therefore special requirements are imposed on the materials used for interior decoration. To interior decoration of the veranda a long period had a good time appearance and didn't demand frequent repairs, it is required to use high-quality, moisture-resistant materials. If you have basic skills in performing repair work finishing the veranda can be done with your own hands.
This work must begin with drawing up an estimate. Plan the order of work, select and purchase in advance required material so that the interior finishing is done quickly and efficiently. List of works for finishing the veranda:
- Selection of materials.
- Ceiling finishing.
- Covering the walls of the veranda.
- Floor covering.
What materials are used to finish the veranda?
If you want to receive beautiful finish verandas, the choice of quality materials is critical. The peculiarity of the selection of materials is that in most cases an unglazed veranda attached to a house is more like an open terrace, which is seriously exposed to the external environment. Therefore, the material must not only match specific design, but also be resistant to high humidity, temperature changes and sunlight.
Diagram of the structure of the timber imitation panel.
The most common material for such work is wood lining. This material can be used to cover both the walls and the ceiling of the veranda. This is an environmentally friendly natural material that has a beautiful appearance and a pleasant smell of wood.
Drywall is waterproof. Environmentally friendly, non-flammable material, easy to install, easy to process, allows for a wide variety of finishing.
MDF is a material that imitates wood. Durable material, the surface of which is made with wood imitation. However, when it gets wet, it swells and loses its quality. Can be used for finishing closed verandas.
PVC panels. Inexpensive, moisture-resistant material, has a rich texture, a wide variety of colors and shades. Easy to install, easy to clean. Durable and non-flammable material.
Siding - practical, inexpensive material. Available various colors, with imitation wood, House block, lining. Does not rot, is resistant to fire, temperature changes, has a long service life, and is easy to maintain.
Ceiling finishing procedure
Diagram of a device for insulating a veranda wall.
The process of making a ceiling begins with its preparation. First of all, it is necessary to treat with an antiseptic and fire retardants. wooden structures veranda ceiling. Then install the frame under the sheathing. The frame is made of bars measuring approximately 30x50 mm. Before installation, the bars are impregnated with an antiseptic.
After it has dried, using self-tapping screws, the bars are attached to the roof rafters in increments of about 50 cm, maintaining horizontality, which is maintained using a level.
If the veranda is closed, the ceiling is insulated, which allows you to use the veranda until late autumn. To insulate the ceiling, first install waterproofing film and attached to the rafters, then insulation is installed between the rafters. Mineral wool or expanded polystyrene is used as insulation. After completing this work, the ceiling is sheathed with clapboard or other material.
The lining is laid perpendicular to the frame slats and nailed into the end with thin galvanized nails. After installation, the surface of the lining is sanded and varnished.
Scheme of a wooden veranda.
When covering with PVC panels, a starting profile is installed in the corner of the room on the sheathing; it helps to assemble the panels together. Then a panel sheet is inserted into the profile groove. It is attached with self-tapping screws or special holders. The next panel is placed in the groove, secured, and so on. During installation, a compensation gap of about 2 cm is provided, which is then covered with a plinth.
Similarly, the ceiling of the veranda is covered with siding and MDF.
To install drywall, instead of wooden blocks, it is better to use a special metal profile as lathing. Elements are installed on the profile, to which sheets of plasterboard are attached using self-tapping screws.
After this, the surface of the veranda ceiling is puttied, cleaned, and it is ready for finishing. You can glue it as a decoration vinyl wallpaper, paint or cover with artistic plaster.
Veranda wall cladding
A frame made of wooden blocks is installed on the walls, the verticality of which is checked with a level. If necessary, the walls are insulated. WITH outside A waterproofing film is installed on the wall, which is secured with slats, then insulation is installed and the sheathing is attached. Wooden elements are pre-treated with an antiseptic. Then lining or other finishing material is attached to the frame. And their finishing is carried out.
Veranda floor covering
Scheme of the installation of insulation of the veranda with false ceilings.
One of the finishing elements of the veranda that gives it a decorative, finished look is the veranda floor covering. Today the flooring market represents the widest range of materials.
Wood remains one of the popular coverings. However, such coating requires careful maintenance and is expensive.
When finishing a veranda with your own hands, laminate is widely used. It has a long service life, is resistant to abrasion, is very easy to install, and does not require additional maintenance. However, it is afraid of moisture, and can only be used as a floor covering on a closed veranda.
For an open veranda the best option may be porcelain stoneware or PVC tiles.
Porcelain tiles - modern look flooring: strong, durable and not afraid of temperature changes, moisture, or sunlight.
PVC tiles - the new kind floor covering. Made from quartz sand and vinyl with the addition of polyurethane. This is a very durable, wear-resistant material, not afraid of moisture, and resistant to ultraviolet radiation.
Self-leveling floors are manufactured using self-leveling mixtures. If the manufacturing technology is followed, the result is a floor with a perfectly flat surface. It can be applied to any surface. It is very durable, resistant to moisture, alkali and acid solutions. Does not require any additional care.
Scheme of the terrace arrangement.
Linoleum, a traditional flooring material. Very easy to install. Placed on a flat surface to which it is glued bitumen mastic. It is not afraid of moisture, wear-resistant, but is sensitive to sudden temperature changes, so it is better to use for closed veranda.
The veranda overlooking the garden is a great place to relax and socialize. The colorfully designed interior will create a feeling of comfort and coziness. Properly done decoration of the veranda with your own hands will be wonderful designer decoration any home.
How to sheathe the inside of a veranda inexpensively
Veranda owners may often ask themselves the question of decorating this comfortable space. There are two types of finishing, which are determined by the scope of work. The first is covering the veranda from the outside, the second is working from the inside. On our website you could find information about materials for external cladding. And this article will be devoted to internal work. At the same time, you will consider economical cladding options that are worthy and have been used for many years. Then your veranda will be beautiful and protected.
After all, this room is adjacent to the living room and can be used for different purposes. We can say that for owners of private houses this is additional space. Let's find out what to cover the inside of the veranda inexpensively and how to do it. Then you can make full use of the veranda area.
Features of the room
It is clear that the requirements for material for interior decoration are much lower when it comes to exterior decoration. But still, the veranda has some peculiarities, so the selection of products for covering must also be done wisely. The fact is that the veranda has its own special microclimate and can be an unheated room. Therefore, the finishing material must meet the following requirements:
- Practicality.
- Attractiveness.
- Resistance to temperature changes.
- Moisture resistant.
- Resistance to mechanical damage.
- Environmentally friendly, since we are talking about the premises inside.
There are quite a lot of materials that meet these requirements. However, not all of them are affordable in terms of price. Therefore, we recommend that you consider using MDF panels, wood paneling and PVC. They solve assigned tasks perfectly and cope with all negative factors. And their price is low. Let's look at each material in more detail.
MDF panels for the veranda
Often the veranda is covered with MDF panels. In some ways, the material resembles lining, as it is produced in wide boards. Their length can reach from 2.6 to 3 m, and their width can range from 15 to 30 cm. In the store you can see a fairly large color scheme products, which allows you not to use standard set, but to expand the spectrum. Thanks to this, you can harmoniously match the style of the entire house, or make a veranda of any color. Moreover, MDF boards can be made to look like natural wood, imitating it.
Here are the advantages of this material:
- Quite attractive and comes in a wide range of tones.
- It is a practical material for covering a veranda, as it is easy to wash. The surface will practically not collect dirt, and dust can be easily removed with a damp cloth. This is important for the veranda, because people often take off their shoes there.
- Installation of MDF panels is quite simple, so even a non-professional can cope with this task.
- Low cost, which allows you to buy this material for the veranda, despite a limited budget.
As you can see, the cladding looks pretty good. Therefore, it is a worthy analogue of expensive materials for covering a veranda. And the installation process is completely simple. You just need to make a frame on the walls from slats, the thickness of which is 2 cm and the width is 4 cm. Next, the fastening of the slats themselves is carried out MDF boards to the slats with nails. The process is very similar to covering a veranda with clapboard.
In order for the veranda trim to be neat and even, it is recommended to use a plumb line or level when working to control everything. The main thing is to set the starting level correctly, and then things will go like clockwork. The panels have grooves, thanks to which the fixation will be reliable and durable. If necessary, the panel can be easily adjusted to size. They can be cut with a saw or jigsaw. After completing the covering of the veranda, you can hide the joints near the ceiling and floor, covering them with skirting boards of identical color.
Now your veranda is ready for use. You can relax in it, make it a dining area, workplace or your greenhouse.
PVC panels for finishing the veranda
Decorating rooms with plastic panels is also quite popular. This option is loved by many specialists and is used everywhere. Plastic panels are the same lining, but made of plastic. Due to this material, finishing has many advantages:
- Long service life.
- Excellent resistance to moisture.
- Easy to care for. The coating can be washed with a cloth.
- Resistance to ultraviolet rays.
- Light weight, which allows you not to weigh down the structure.
- Quite attractive and at the same time practical.
- Installation is very simple.
- The price is reasonable.
- The range of products is large, so the veranda can turn into anything.
It will not take much time to treat a large veranda. The work is done quickly and effortlessly. A veranda finished with this material can be used for various purposes. Besides, PVC panels you can cover both the ceiling and walls of the veranda.
If you try, then all the cladding work can be completed in one day. Installation is also carried out on a frame made of slats, 30×20 or 30×10 mm thick. PVC panels are fastened with nails. The disadvantage of the material is its fragility. By hitting the trim, you can make a dent in it.
Wooden lining for the veranda
And finally, we have come to one of the most popular materials, which has earned an honorable place among homeowners. The lining is made from natural wood, so it is 100% safe. The material is ideal for interior decoration of both walls and ceilings. And the appearance of the cladding is simply magnificent.
Main advantages of the material:
- The lining is durable and resistant to impacts and all kinds of loads.
- Is practical.
- Has an attractive appearance.
- It does not release any toxins, but, on the contrary, enriches the room with the pleasant smell of natural wood.
- The cost is not exorbitant, but quite affordable. In this case, the material is divided into classes, which allows you to choose your category.
- Installation is quite easy.
- You can choose a board of different shades.
- Durability, the material with proper care and protection will last 20 years.
As for the classes mentioned above, the lining is divided into 4 groups:
The quality of the material in this list is listed in ascending order. The cheapest lining option for finishing a veranda is class “C”. In products greatest number knots and minor defects. To finish the veranda, it is recommended to use class “B” or “A”, since “Extra” is very expensive.
How to cover the inside of the veranda with clapboard? The technology should be familiar to you:
- Vertical slats (lathing) are placed on the wall.
- After which the first plank is fixed, starting from the corner.
- This is the most critical stage, since the evenness of the entire finish will depend on it. When working, use a level.
- Further boards are fixed to each other through grooves.
The method of fixing the bar may be different. They are nailed with galvanized nails, wood screws, a regular stapler or clamps. After installation is complete, it is recommended to protect the lining with varnish or other impregnations. This will extend the life of the covering on the veranda.
Let's sum it up
As you can see, you don’t need to spend incredible amounts of money on covering a veranda, buying expensive material and hiring workers who will do everything for you. hard work. Thanks to these easy-to-install materials, which are inexpensive, you can sheathe your veranda with high quality, creating comfort, beauty and protecting the walls from various factors.
External and internal decoration of the veranda
A modern country house is designed to provide the best living conditions. Currently, all conditions have been created for this - an abundance of design solutions in house construction, a variety of traditional and new proven materials.
One of the elements of private buildings is currently a terrace - a fully or partially open area equipped with a roof. It allows you to fully feel like a part of nature, practically without leaving your home. What materials and in compliance with what requirements can be used to finish the terrace will be discussed further.
Classic terrace design
Structurally, an extension to a house, called a terrace or veranda, is a podium raised above the ground on one of the types of foundations, and a roof made of some material, supported by several support beams. According to their design, such structures are divided into:
Open veranda
This view is good when located on the leeward sunny side. Due to the absence of fences, there are practically no boundaries between the veranda and the space surrounding it. It is better if the floor height of such a structure is low. This is especially true when children live in a country house.
This option requires minimum costs for its construction. Yes, and finishing the veranda will not be required high expenses. But maximum demands must be made on its quality, since the structural elements will be under constant influence of excessive moisture, frost, winds, and temperature changes.
Partially closed option
Such a terrace retains its airiness and openness, but ensures high safety for household members and their guests. The main difference from the previous option is the presence of fences made of timber, in the form of a frame structure made of lumber, as well as from blocks or bricks, followed by finishing of the veranda walls outside and inside.
Photo: 3D project of a country house with a veranda
Due to the lack of complete isolation from the atmosphere, the operation of structures of the first and second types is possible only in the warm season. It is impossible to properly insulate them due to the design features, and it is quite difficult to completely protect visitors to such a terrace from the wind and raindrops flying inside.
Closed terraces
This type is most suitable for year-round use as an additional room. Even in the winter cold, closed from the wind and frost, you can enjoy hot tea while admiring the beauty of nature. In this case, it is better to combine the interior decoration of the veranda with insulation of all its walls. This will minimize heating costs for the house as a whole.
Veranda finishing options
The manufacturing process of the described structures is not complicated and is quite accessible with your own hands, as is finishing the veranda inside or outside. Since the topic of the article involves a more detailed introduction to the second part of the work, we will consider them, focusing on possible options, their features, advantages and disadvantages.
Currently, the interior of the veranda is covered using the following materials:
- wooden lining;
- plastic panels;
- MDF panels;
- cement plaster and cement-based artificial stone.
Decorating the veranda with wood
The classic option is the use of natural wood materials for finishing walls not only in the interior of the house, but also in extensions. The lining is distinguished by its good appearance, ease of installation and low requirements for the quality of base preparation.
Its installation is carried out on a lathing made of 40x40 mm bars using special fasteners - clamps, which grab the panels by the groove and securely fix them. Finishing parts can be placed vertically, horizontally or at an angle to the floor.
When finishing the exterior, you can sheathe the veranda only by installing the lining parallel to the soil with the ridges up to prevent the accumulation of water in the grooves.
Plastic finish
Also quite a common option. It is better to decorate a closed veranda with such panels. In this case, temperature changes are less sensitive to the material, which helps to increase its service life.
Unlike wood materials, plastic is practically not afraid of water. Modern retail chains offer many options for both color and texture design of plastic panels.
Installation of plastic trim is easier than wood trim. Thanks to the considerable width of the panels, the process is faster.
It is convenient to fasten the finishing parts to the sheathing using a construction stapler, driving the staples into a wide shelf along the edge of the products. Plastic panels do not require further finishing with paintwork, they can be easily washed with a damp cloth, and dust does not settle on them.
Interior finishing with MDF panels
Another common finishing material for interior work is MDF panels. Like the previous option, they are distinguished by a large working width, which allows for sheathing to be carried out quite quickly. For fastening to wooden sheathing, clamps are used, similar to those used when installing wooden lining.
Thanks to the large number of colors that imitate natural wood, stone and even leather, this interior decoration of the veranda will have a very high quality look. With all its advantages, MDF also has a significant drawback - very low moisture resistance. In this regard, it is better not to use them for finishing open terraces. Otherwise, additional protection will be required in the form of varnishing all sides of the panels.
Decorating veranda walls with cement materials
In the case of using cement-containing building materials - blocks with one or another filling, or bricks - to make a terrace, it is better to finish the walls with mixtures or parts that are similar in composition.
Please note that gypsum-based plaster and gypsum artificial stone are not suitable for covering the walls of open verandas.
Often home owners are stopped by the high cost of cement finishing materials. At the same time, it is not difficult to produce the required amount of original artificial stone yourself in a home workshop. By adding aniline dye, you can get a unique interior in the room being finished.
Polycarbonate for finishing terraces
As already noted, the materials listed above, used in finishing the interior space of verandas, have certain disadvantages that limit their use. In recent years, external walls and roofs of terraces have increasingly been covered with polycarbonate - an artificial transparent material that allows you to create a closed space while maintaining visual contact with the surrounding nature.
There are two main types of this plastic:
- Cell phone. It is characterized by minimal weight, high light transmittance, and durability, therefore it is often used for roofing terrace roofs.
- Monolithic. Its properties are close to real quartz glass, but unlike it it does not have such high fragility. This determined its use in vertical frame structures - windows, doors, transparent walls.
Modern manufacturers are not limited to producing colorless sheets. To create a soft shadow, we recommend using green, blue, red, yellow cellular polycarbonate for the roof. You can combine several colors, giving the entire design brightness and uniqueness.
Covering veranda walls with cellular polycarbonate is quite easy to do yourself. To work you will need a minimum set of tools:
- cutting knife - any construction knife will do;
- screwdriver
The polycarbonate installation technology involves the following list of works.
The installation of cellular polycarbonate on the roof of the terrace is carried out in a similar way. If there is a ridge - the junction of two roof slopes, use a special ridge profile, sold in organizations that sell sheets.
In the absence of cutting experience, cutting sheets to the required sizes can also be done by workers at construction bases.
As follows from our review, the amount of materials for covering terraces is sufficient to create a unique structure. Before finishing your veranda with any of them, carefully study all the operating features in a particular case.
The veranda in a private house is used by the owners in different ways. For some, it’s just a vestibule for transition from the street to a living space, for others, it’s a place to store food supplies and rarely used items. But the majority prefer to relax here, spending free time on fresh air. When deciding how to cover an unheated veranda inside, you need to take into account its purpose and realistically assess your budget. But it is much more important to choose materials that will withstand difficult operating conditions and retain their original appearance for a long time.
Materials for interior cladding
Any unheated room is susceptible to temperature fluctuations and changes in air humidity, so it must be finished with materials that can easily withstand such influences. But there is a big difference between closed glazed verandas and buildings open to all the winds, not protected from direct contact with precipitation, sunlight and other factors.
If desired, the glazed veranda can be insulated and equipped with a heater to extend its life. seasonal use. Together with a closed contour, this will allow you to diversify interior design, choosing the appropriate type of finish from quite large assortment suitable materials. With an open terrace, such a trick will not work; accordingly, the materials for it need to be selected those that are intended for exterior decoration.
Open verandas
Such verandas are most often light frame buildings - terraces with a canopy, standing directly on the ground or raised above it to the floor level of the house. Less common are brick, timber or log structures, and they, as a rule, are erected simultaneously with the main building on the same foundation. If the masonry is done carefully, with jointing or wood treatment with protective and decorative compounds, the walls of such a veranda do not need any additional finishing. Otherwise, the choice of how to cover a terrace with these materials will not differ from the same question regarding frame walls.
Since the interior decoration of walls and ceilings must withstand harsh and changeable weather conditions, only a few can be chosen from the wide variety of cladding materials. This is wood, siding, polycarbonate:
- Wood for cladding is used in the most different types. These are slats, edged and tongue-and-groove boards, figured moldings, lining. The most common option is lining, which today comes in many types depending on the shape of the profile. With its help they sheathe interior walls By wooden frame. Ordinary lumber is used in the same way, but if it is sanded on all sides, boards or slats can be used to fill the frame under the railings between support pillars in the form of continuous flooring, picket fence, lattice. This will allow you to solve two problems in one fell swoop and no longer have to think about how to cover the outside of the terrace.
It is important! Wood needs mandatory protective coating, protecting it from rotting, fire, and damage by insects. This is especially important when used on outdoors. Protective compounds can be colorless or tinted, which will give the cladding the desired shade without additional processing. This coating must be applied periodically, at least once every 2-3 years.
Of all the types of siding, only metal is not suitable for interior decoration of open terraces; it gets very hot in summer and is unpleasant. cold in winter. Vinyl, fiber cement and others façade panels can be used both indoors and outdoors. Their main advantages are durability, ease of maintenance, and preservation of appearance without the application of protective or decorative compounds.
Video description
This video shows an example of finishing with fiber cement panels:
- Monolithic or cellular polycarbonate is an ideal solution for summer outdoor terraces. It can be used as the main finishing material by inserting colored or transparent sheets into frames and covering the under-rail space with them. Or attach the canvas to a wooden balustrade from the inside.
Advice! Before installation, sheathing elements made of cellular polycarbonate must be closed around the perimeter with end caps in the form U-shaped profile. Otherwise, dust and debris will clog the air channels inside the material, which, together with the moisture condensing in them, will become an excellent breeding ground for microalgae. And after a couple of seasons the finish will lose its appearance.
The same materials, with the exception of heavy types of siding, are also suitable for ceiling cladding. Problems can only arise with transparent polycarbonate, behind which it is impossible to hide the wiring electrical wires for lighting. But it can be solved with the help of decorative ceiling beams or cable channels.
As with walls, polycarbonate usually becomes a single exterior and interior finishing material if it is used to cover a roof.
Enclosed verandas
In home extensions, in which windows and doors are installed and the ceiling is lined, it is always warmer and drier than outside in frost or rain. The wind does not penetrate here, straight Sun rays and precipitation, so the question of how to sheathe the inside of an unheated veranda cheaply can be answered in more detail.
To the materials already described, you can safely add plastic, MDF, plasterboard and other sheet materials that serve as the basis for subsequent finishing.
- By plastic we mean seamless Wall panels and lining made of polyvinyl chloride (PVC) - a material that is absolutely resistant to moisture. It does not rot, does not attract interest from insects and rodents, and does not become a source of breeding ground for mold fungi. In their structure, these panels resemble cellular polycarbonate, but they are not transparent and are distinguished by a huge variety of patterns, colors and textures. And they are mounted similarly to wooden lining - they are attached to the sheathing and connected to each other using a tongue-and-groove lock. Its light weight and ease of cleaning make this inexpensive material ideal for ceiling cladding.
On a note! When working with PVC cladding, one must take into account its fragility when the air temperature drops greatly. In this case, the panels themselves do not crack, but this easily occurs with an accidental impact.
Video description
In this video you will find detailed instructions for installation of plastic panels:
- MDF panels, unlike plastic, are almost natural material, as they are made from wood chips pressed under high pressure. During the process, the chips are glued together with lignin, a substance found in the wood itself, which makes it possible to do without synthetic resins. But that's exactly what natural origin The material makes it not very resistant to moisture. When deciding how to cover the inside of the veranda and choosing MDF panels, you should make sure that all ends are closed or treated with sealant, since moisture is absorbed mainly through unprotected areas of the material. Including through chips on the surface. The technology for installing such panels is similar to installing wooden lining.
- In such operating conditions, only moisture-resistant plasterboard is used, and if a stove or barbecue is installed on the veranda, then fire-moisture resistant. This material is not a finishing material, but serves as an ideal base for painting, decorative plaster or tiling.
- Instead of drywall, you can use another sheet material– OSB or DSP boards that are not afraid of moisture and other atmospheric influences. Before sheathing the veranda with such sheets, it is necessary to build a reliable frame from metal profiles or wooden blocks, the pitch between which is selected taking into account the size of the canvas.
As for the subsequent finishing of the prepared base, it must also be resistant to frost and high humidity. Therefore, only the paint that is intended for outdoor use is selected. Plaster – preferably cement or polymer based, gypsum is not suitable, as it will absorb moisture.
Wall coverings look very impressive on verandas decorative stone or brick. The composition of the raw materials for the manufacture of such tiles also varies, and you must definitely pay attention to it, avoiding the purchase of gypsum products.
Don't forget that adhesive compositions for installation of tiles and grout for joints should also be selected according to operating conditions, otherwise the cladding may fall off the walls over time.
Advice! Before sheathing the veranda with such a finish, you need to estimate how much distance the frame, base and coating itself will “eat,” and whether it will become critical for the area of a small room.
Video description
The following video shows how to decorate walls with brick tiles:
In addition to being resistant to weather conditions, materials for covering verandas should be easy to maintain: easy to wash and clean, since they get dirty easier and faster than finishing in the house.
Exterior cladding materials
Thinking about how to cover the outside of the veranda is always associated with the desire to create a complete image of the house and its extension. Therefore, most often they choose the same materials with which the facade is finished, or those that are similar in appearance to it. For example, if a house is built from rounded logs, frame veranda It would be logical to clad the outside with a wooden or metal blockhouse. And if it is covered with siding, the extension is also finished with the same material.
But this is not a rule, but rather the result of the practical thinking of most homeowners. Architects and designers often offer more interesting solutions, creating a single ensemble from seemingly incompatible materials.
If you are deciding how to cover the outside of the veranda cheaply and beautifully, you can return to already known materials - wooden lining and siding.
- If for interior decoration they often choose ordinary lining or an imitation of timber with a relatively flat surface, then panels with a more pronounced relief are suitable for the exterior - a blockhouse that imitates a log, or an American panel that gives the impression of overlapping planks, a herringbone pattern.
It is important! Having chosen horizontal cladding, it is necessary to place the lining boards with the grooves down so that water does not flow into them.
- Even more cheap option- overlapping cladding with edged, unedged boards or even a slab with the bark removed. In this case, fixation is performed directly through the boards, right through to the frame or solid base.
- Any siding is suitable for external cladding, including metal. But you need to take into account that without a layer of thermal insulation between the outer and inner cladding, such a veranda will be very hot in the summer.
- Most affordable option How to sheathe a veranda from the outside inexpensively, this is a metal profiled sheet - an analogue of metal siding in terms of characteristics and operational parameters, it allows you to complete the work in a very short time due to large area simultaneously overlapping surface.
- Moisture-resistant OSB-3 boards will cost even less, but they can only be considered as a temporary option or a basis for future decorative finishing.
If you are not too limited in funds, you can choose a more expensive, practical and durable option for plank wood trim. These are non-grooved boards made of larch, ash, cedar and other types of wood that are resistant to rotting. They are not mounted end-to-end, but with a small gap between the planks, which avoids their deformation when exposed to moisture.
Planken comes with straight or beveled edges, with a smooth or grooved surface, untreated or factory-painted. Some manufacturers impregnate products with antiseptic compounds under pressure, which significantly increases their service life, and also complete them with a frame system and fasteners.
Advice! When purchasing untreated plank, it is impregnated with special synthetic compounds or linseed oil before installation.
A separate question is how to sheathe the veranda from the outside between the ground level and the walls, if it stands on a screw or columnar foundation. There can be many options from brickwork before covering the frame with any suitable material:
- basement siding;
- metal siding;
- plastic base panels;
- insulated composite panels with decorative layer from clinker tiles, etc.
Video description
An option for finishing the plinth with TechnoNIKOL soft facade tiles is shown in the following video:
Conclusion
Before sheathing the veranda inside or outside, you need to study the features of different facing materials, the technology of their installation and the need to maintain their characteristics using protective and decorative agents. Some materials in the store may cost much more than others, but in the end they will cost less due to ease of installation and low requirements for regular processing and restoration decorative covering. Great importance It also has the appearance of the cladding, its combination with the rest of the elements of the house. Therefore, the choice always remains with the owner.
A modern country house is designed to provide the best living conditions. Currently, all conditions have been created for this - an abundance of design solutions in house construction, a variety of traditional and new proven materials.
One of the elements of private buildings is currently a terrace - a fully or partially open area equipped with a roof. It allows you to fully feel like a part of nature, practically without leaving your home. What materials and in compliance with what requirements can be used to finish the terrace will be discussed further.
Users often search:
Classic terrace design
Structurally, an extension to a house, called a terrace or veranda, is a podium raised above the ground on one of the types of foundations, and a roof made of some material, supported by several support beams. According to their design, such structures are divided into:
- open;
- partially closed;
- closed.
Open veranda
This view is good when located on the leeward sunny side. Due to the absence of fences, there are practically no boundaries between the veranda and the space surrounding it. It is better if the floor height of such a structure is low. This is especially true when children live in a country house.
Photo: 3D project of a country house with a veranda
Due to the lack of complete isolation from the atmosphere, the operation of structures of the first and second types is possible only in the warm season. It is impossible to properly insulate them due to the design features, and it is quite difficult to completely protect visitors to such a terrace from the wind and raindrops flying inside.
Closed terraces
This type is most suitable for year-round use as an additional room. Even in the winter cold, closed from the wind and frost, you can enjoy hot tea while admiring the beauty of nature. In this case, it is better to combine the interior decoration of the veranda with insulation of all its walls. This will minimize heating costs for the house as a whole.
Veranda finishing options
The manufacturing process of the described structures is not complicated and is quite accessible with your own hands, as is finishing the veranda inside or outside. Since the topic of the article involves a more detailed introduction to the second part of the work, we will consider them, focusing on possible options, their features, advantages and disadvantages.
Currently, the interior of the veranda is covered using the following materials:
- wooden lining;
- plastic panels;
- MDF panels;
- cement plaster and cement-based artificial stone.
Decorating the veranda with wood
The classic option is the use of natural wood materials for finishing walls not only in the interior of the house, but also in extensions. The lining is distinguished by its good appearance, ease of installation and low requirements for the quality of base preparation.
Its installation is carried out on a lathing made of 40x40 mm bars using special fasteners - clamps, which grab the panels by the groove and securely fix them. Finishing parts can be placed vertically, horizontally or at an angle to the floor.
Thematic material:
When finishing the exterior, you can sheathe the veranda only by installing the lining parallel to the soil with the ridges up to prevent the accumulation of water in the grooves.
Plastic finish
Also quite a common option. It is better to decorate a closed veranda with such panels. In this case, temperature changes are less sensitive to the material, which helps to increase its service life.
Unlike wood materials, plastic is practically not afraid of water. Modern retail chains offer many options for both color and texture design of plastic panels.
Installation of plastic trim is easier than wood trim. Thanks to the considerable width of the panels, the process is faster.
It is convenient to fasten the finishing parts to the sheathing using a construction stapler, driving the staples into a wide shelf along the edge of the products. Plastic panels do not require further finishing with paintwork, they can be easily washed with a damp cloth, and dust does not settle on them.
Interior finishing with MDF panels
Another common finishing material for interior work is MDF panels. Like the previous option, they are distinguished by a large working width, which allows for sheathing to be carried out quite quickly. For fastening to wooden sheathing, clamps are used, similar to those used when installing wooden lining.
Thanks to the large number of colors that imitate natural wood, stone and even leather, this interior decoration of the veranda will have a very high quality look. With all its advantages, MDF also has a significant drawback - very low moisture resistance. In this regard, it is better not to use them for finishing open terraces. Otherwise, additional protection will be required in the form of varnishing all sides of the panels.
Decorating veranda walls with cement materials
In the case of using cement-containing building materials - blocks with one or another filling, or bricks - to make a terrace, it is better to finish the walls with mixtures or parts that are similar in composition.
Please note that gypsum-based plaster and gypsum artificial stone are not suitable for covering the walls of open verandas.
Often home owners are stopped by the high cost of cement finishing materials. At the same time, it is not difficult to produce the required amount of original artificial stone yourself in a home workshop. By adding aniline dye, you can get a unique interior in the room being finished.
Polycarbonate for finishing terraces
As already noted, the materials listed above, used in finishing the interior space of verandas, have certain disadvantages that limit their use. In recent years, external walls and roofs of terraces have increasingly been covered with polycarbonate - an artificial transparent material that allows you to create a closed space while maintaining visual contact with the surrounding nature.
There are two main types of this plastic:
- Cellular. It is characterized by minimal weight, high light transmittance, and durability, therefore it is often used for roofing terrace roofs.
- Monolithic. Its properties are close to real quartz glass, but unlike it it does not have such high fragility. This determined its use in vertical frame structures - windows, doors, transparent walls.
Modern manufacturers are not limited to producing colorless sheets. To create a soft shadow, we recommend using green, blue, red, yellow cellular polycarbonate for the roof. You can combine several colors, giving the entire design brightness and uniqueness.
Covering veranda walls with cellular polycarbonate is quite easy to do yourself. To work you will need a minimum set of tools:
- cutting knife - any construction knife will do;
- screwdriver
The polycarbonate installation technology involves the following list of works.
The installation of cellular polycarbonate on the roof of the terrace is carried out in a similar way. If there is a ridge - the junction of two roof slopes, use a special ridge profile, sold in organizations that sell sheets.
In the absence of cutting experience, cutting sheets to the required sizes can also be done by workers at construction bases.
As follows from our review, the amount of materials for covering terraces is sufficient to create a unique structure. Before finishing your veranda with any of them, carefully study all the operating features in a particular case.
The content of the article:
Finishing a veranda is a set of measures aimed at its improvement. A veranda is an extension adjacent to the wall of a house. She belongs to the summer species unheated premises and may be indoors or open version execution. Depending on the type of extension, the interior walls are finished. In addition, the configuration of the veranda and its external design should fit well into the exterior of the entire building. Having simple skills in performing construction work, you can finish the walls of the veranda with your own hands.
The choice of material for finishing the walls of the veranda
The materials chosen for finishing the walls of the veranda must meet practical and aesthetic requirements. The peculiarity of their choice is the lack of heating in the closed extension and the serious impact of climatic conditions on the structures of the open veranda. Therefore, the material used for decoration must not only be visually attractive and match the design, but also withstand exposure to the sun, high humidity and temperature fluctuations.
Covering the walls of the veranda can be done in many ways finishing materials which are used for interior and exterior work:
- . It belongs to the classics of the genre, as it is the most popular material for wall cladding due to its environmental friendliness, excellent appearance and pleasant aroma, exuded by natural wood.
- Gypsum plasterboard sheets (GKL). For verandas, their moisture-resistant version is suitable. Such products differ from conventional gypsum boards in their green. The material is environmentally friendly, easy to install and can be easily processed in numerous ways. It can take almost any shape, and this is important when decorating walls. This type of cladding is used in closed verandas.
- . This material imitates natural wood. It is quite durable, but a humid environment is not for it. Therefore, MDF can be used to cover the walls of a closed veranda.
- PVC panels. This is a durable and inexpensive moisture-resistant material. It is presented in a rich assortment of various shades and colors, can have different textures, is very easy to work with and is not particularly demanding to care for. Suitable for cladding walls of any type of extension.
- Siding panels. They are practical to use and affordable. Often imitate wood and come in a variety of colors. The material does not rot, is resistant to temperature changes and fire, easy to care for and durable. Most often used for exterior wall decoration on the veranda.
Preparatory work before finishing the walls on the veranda
If the veranda has glazing, it is better to finish its walls after installing thermal insulation under the windows. In this case, the room can be used almost until frost sets in.
To insulate a closed veranda you can use mineral wool or polystyrene foam. To begin with, waterproofing should be secured to the walls; you can use a moisture-proof polyethylene film as it. It is laid with an overlap of 150-200 mm, the joints of the canvases must be glued with metallized tape.
After this, it is necessary to install lathing on the walls. The material for it can be a wooden beam, pre-treated with an antiseptic. The cross-section of the beam should be selected according to the thickness of the insulation, and the size of the sheathing cell should correspond to the width of the insulation.
Then the insulation, in particular mineral wool, should be packaged in waterproof material and placed in the cells of the sheathing. Wrapping the insulation will protect it from moisture and maintain its functionality for many years.
After this, a foil membrane should be secured to the sheathing on top of the insulation and its joints should be taped. During the insulation process, it plays the role of a heat-reflecting screen. At this point, the thermal insulation of the walls can be completed.
Veranda wall finishing technology
Having chosen what to cover the walls on the veranda with, you can begin finishing them. Below we will look at several of its options.
Decorating veranda walls with PVC panels
This finishing method is inexpensive, but it can make an ordinary room cozy and interesting. The panels are not afraid of high air humidity and sudden changes in its temperature - they are not capable of causing deformation of this material. Installation of the panels is easy and without any tricks.
The disadvantage of the material is its fragility, although currently you can purchase “armored” panels, the cost of which will be twice as much as usual. Therefore, after installing such cladding, you should be more careful when moving chairs towards it or leaning on the wall. To minimize risks, there is such a construction trick: the first plank of the panel sheathing is mounted at the level of the knees, the second - at the pelvis, and the third - at the shoulder.
The frame for plastic panels is made of wooden slats or profiles, which are used when installing gypsum boards. The slats can have a cross-section of 30x10 or 30x20 mm; before use they should be treated with an antiseptic.
The sheathing slats should be fastened in a perpendicular direction relative to the installation of the panels. For example, if the plastic on the wall needs to be placed vertically, then the slats for attaching it should be placed horizontally on the wall, the step between them should not exceed 50 cm.
After making the sheathing in the corner of the room, you need to secure the mounting angle or starting profile with screws or nails. The corner will allow you to join the panels to each other. The starting profile is installed if the adjacent wall will be sheathed with a different material. You need to install a mounting strip for the baseboard on the ceiling.
The first panel is inserted into the guide profile with the tenon facing towards the installation. Then it needs to be fixed to the sheathing using a self-tapping screw with a press washer. Then the tenon of the next PVC panel must be tightly inserted into the groove of the previous one and secured. All other cladding panels are installed in the same way.
Due to the fact that plastic has thermal expansion, a gap of 20-30 mm should be left at the bottom and top of the wall to compensate for it, masking it with a plinth.
Important! Panels with a pattern when covering walls are installed from left to right. Plain panels can be mounted starting from any side.
Decorating veranda walls with MDF panels
This material is quite popular among adherents self-finishing. MDF panels are stronger than plastic, but are not resistant to moisture. Therefore, they should only be used on closed verandas.
The installation process of MDF panels is similar to the previous one. Only in this case their fastening is done using metal special devices- clamps, which are fixed to the material with small nails or a construction stapler. This must be done through a guide; it will prevent damage to the edge of the panel.
Decorating the walls of the veranda with clapboard
They call it lining wooden board up to 22 mm thick, having special grooves with the help of which the installation and joining of cladding elements is carried out. If the material is treated with an antiseptic, its service life can be extended to 20 years.
According to the production method, the cladding board can be solid or spliced. In the latter case, pieces of high-quality wood are connected to each other in a special way. Such products do not have flaws in the form of knots or cracks, but are not suitable for covering the walls of an open veranda.
The reason for this is the formation of cracks in the places where the boards meet at high humidity, which spoil the appearance of the finished cladding. The most expensive lining is almost always spliced. It has an “extra” class, and products of classes A, B and C are made from solid wood.
Before finishing the walls on the veranda with cladding boards, the material must be left to adapt in a closed room for several days, and then the lining must be treated protective composition. Installing boards on veranda walls is similar to installing PVC and MDF panels.
There are several ways to attach it:
- The simplest of them is fastening using galvanized nails. In this case, they are driven in along the center of the planks, and the caps are recessed into the wood using a punch.
- Fixing the sheathing board with self-tapping screws is more labor-intensive, but the fastening points are not visible. A hole with a depth of about 10 mm is drilled in the board on the tenon side. The diameters of the drill and fastener heads must match each other. Then the plank is screwed to the sheathing batten, and the screw is recessed into the hole and closed with a dowel on top. The fastening area is then sanded.
- The board can be attached to the sheathing using mounting brackets. For this, a pneumatic or mechanical construction stapler is used.
- Another way is fastening wood paneling kleimers. In this case, it is first attached to the rear wall of the mounting groove of the first strip. Then it is fastened with nails to the wall and only then the clamp is fixed. The same clamp is installed on the second board, its tenon is inserted into the groove of the previous plank and the clamp is secured to the sheathing batten. Using such fasteners, only internal wall cladding is performed.
Before painting the walls on the veranda, it is recommended to apply the selected varnish to a sample of the material and let it dry. It happens that after drying the shade of the coating changes, and it is quite difficult to remove a layer of varnish that does not correspond to the design. Therefore, it would be better to buy a small container with a painting composition for testing, and if it suits, purchase the rest.
If there is a need to leave the cladding wood in its original form, a colorless glaze containing an ultraviolet filter can be applied to it. It will help prevent the walls of the veranda from fading from exposure to the sun.
Exterior wall decoration of the veranda
It can be done using lining or siding. Wood cladding in this regard, it is somewhat capricious. Despite the treatment of its elements with various antiseptics, when exposed to precipitation, sunlight and seasonal temperature changes, the cladding may lose its original appearance if it is not taken care of.
Therefore, every year you will have to carry out various measures to preserve it: impregnation, painting, etc. But if the choice towards using wood has already been made, it is important to remember that horizontal mount External cladding boards should be made with the tenon facing up, fixing them in 2 rows on each side of the key joint.
Exterior decoration of veranda walls with siding is more good option. This type of cladding got its name in the 19th century. Planed and painted boards were attached at an angle to the plane of the wall so that each subsequent horizontal element slightly overhangs the previous one. This position of the boards allowed water to roll down the cladding without delay. Nowadays, siding performs two functions - protective and aesthetic.
Most commonly used for external wall cladding vinyl siding. Its popularity is due to ease of installation, practicality and affordable price. Externally the material looks like regular board, which is used for façade cladding.
However, vinyl will not lose its appearance even after a couple of decades, despite seasonal temperature fluctuations, bitter frosts and heavy rainfalls. In addition, dirt does not stick to this material and maintenance is minimal - just wash off the dust from the cladding with a garden hose. Thanks to a huge number of shades, siding can be matched to any home exterior; it will fit perfectly into the overall ensemble.
Installation of vinyl siding panels is carried out in the following order:
- First, you need to make and install sheathing for cladding the walls of the veranda. This will require unedged board 30 mm thick or wooden beam with dimensions cross section 40x50 mm. It must be fixed in a vertical position in increments of 400-500 mm over the entire surface of the walls. Additional wooden blocks should be installed around the windows, at the corners of the veranda, along the upper and lower edges of the future cladding.
- From below, along the perimeter of the walls in a strictly horizontal position, it is necessary to secure the starting profile to the sheathing using self-tapping screws.
- After this you need to install corner profiles around openings, as well as in all corners of the building. The lower edge of the corner profile should be located 5-6 mm below the level of the starting strip.
- Then you should cut the panels. Vinyl is easy to cut with scissors, a hacksaw or electric jigsaw. Due to vinyl panels have temperature expansions, each of them needs to be made shorter than the wall by 5-7 mm.
- After this, the prepared panel must be slightly bent in the center, and its edges inserted into the grooves of the profiles located at the corners of the wall. Then the panel should be aligned and its lower edge should be inserted into the starting profile. The upper edge must be secured with self-tapping screws to the sheathing through special holes.
- Pressing the screw heads tightly against the panel material is unacceptable. The oval shape of the fastening holes is specially designed for free movement of material relative to the screw part of the fastener when air temperature changes. There should be a distance of 1.5 mm between the screw head and the sheathing.
- The next panel must also be inserted into the corner profiles, snapped into the groove of the previous element and secured to the wall sheathing.
- Before installing the last panel, it is necessary to level the finishing profile on the sheathing. Then you need to cut the panel to the required width and snap it into the previous paneling element, simply inserting the free edge of the product into the finishing profile. This completes the covering of the veranda walls with siding.