When choosing a material for final finishing Every person wants to get a beautiful and practical final result that can last for many years and at the same time maintain its original appearance throughout the entire period of operation. Lamb plaster is perfect for these purposes. It is intended for internal and external works, so it can be used everywhere.
Good resistance to atmospheric influences and climatic features of any region makes it important element finishing on a vast country scale. Therefore, it is worth taking a close look at this option, as it will perfectly combine good quality at affordable price, which is very important in modern crisis conditions.
Features of finishing material
Decorative “lamb” plaster got its name for the characteristic structure that is obtained after applying the material to the surface. It became an actual replacement for sand-cement material, which in the domestic space was called “fur coat”. New material in all respects it surpassed the outdated model, which had a whole lot of shortcomings.
Thanks to the use modern technologies It turned out to create a practical mixture with a beautiful textured pattern that remains on the wall after the plaster hardens. At the same time, the relief can be adjusted to a certain extent, so it all depends on the skill of the plasterer.
Facade plaster “lamb” has the following properties:
- . Color is achieved not by adding dyes to the surface, but by directly introducing special additives into the structure itself. Therefore, the plaster does not fade in the sun and is not erased by accidental touches.
- . The material allows steam to pass through well, but is completely waterproofed, so water from the street will not be able to penetrate into the interior rooms, and the steam, in turn, will calmly escape from the interior. This property is very important, because otherwise condensation droplets will form on the walls, which will ultimately lead to the appearance of mold or the development of fungal organisms.
- . The material in the frozen state has high level impact strength. So it will absolutely not go astray during accidental collisions with a person. Of course, it will not withstand special blows from a hammer, but it will be reliably protected from any unplanned touches.
- . It has a high level of resistance to acidic and alkaline environments, does not accumulate salts, so can be used in the coastal zone, and is not sensitive to the effects of household gases. Plaster performs well in any situation, so it can be used in rooms for any purpose without any problems.
- . The material dries very quickly, so you don’t have to close the room for several days after plastering the walls.
Available for sale a large number of options, so it’s better to first look at all the photos of “lamb” plaster in order to make the right choice.
Types of plaster
Any building material has several varieties so that it can interest the target audience as much as possible. Acrylic “lamb” plaster allows you not only to beautifully design surfaces, but also to level them in order to achieve the most attractive results. It consists of special elements that have the ability to fill all the cracks encountered along the way, so that after applying the plaster the surface becomes completely flat.
At the same time, to reduce consumption, it is better to pre-treat the walls special mixture, which will be much cheaper. And finishing work can already be done using finishing. For the street it may not be so important that the wall is perfectly flat, but in indoors This is an absolutely mandatory attribute of a successful repair.
The “lamb” “bark beetle” plaster has an even more attractive texture, since here, in addition to the “fluffy” relief, various patterns will be scattered along the entire contour. By appearance they resemble the “work” of a wood pest, which makes asymmetrical moves in the wood structure. Externally, it looks very beautiful, so many users choose this option for decorating their premises.
How to work with decorative plaster?
From the video about working with “lamb” plaster, you can determine that the procedure is not particularly difficult, but requires careful preparation and accuracy. To do this you will need to purchase in advance necessary set tools that will not differ from the kit for working with any other types of finishing material. You can easily find it in a specialized store.
The application of decorative “lamb” plaster is carried out according to the following scheme:
- . The working surface is cleaned of any foreign elements that could disrupt adhesion. To do this you need to use sandpaper or a special scraper.
- . Next, you should additionally prime the surface to kill all bacteria and improve the adhesion of the two materials to each other.
- . Next, you need to dilute the plaster using the method indicated on the package. For mixing, it is better to use a special electric tool, which will allow you to achieve a homogeneous mass in a short period of time.
- . The material should be applied sequentially according to the chosen scheme. The final layer should not exceed four millimeters.
The price of “lamb” plaster will depend on the manufacturer
Lamb type plaster - finishing material, allowing you to create a non-standard surface. Plaster of this type is classified as textured. facing materials. main feature lies in the possibility of applying to uneven walls. With its help you can quickly create decorative surface. This material creates a grainy structure reminiscent of lamb's wool. This quality is why the material got its name.
The main element providing unusual properties material is quartz or marble chips . It is with its help that a grainy surface is created. The diameter of the crumb varies from 1 to 4 millimeters. The size determines how embossed the surface pattern will be: the larger the size, the more grainy the surface will be. The composition may vary depending on the manufacturer. But the basic components remain the same.
The main feature of the components of the plaster is environmental safety for good health. Can also be used instead of marble and quartz dolomite. The granules make the surface more durable and it does not settle even after a long period. Depending on the composition and properties, structural facing plaster Lamb comes in several types:
- cement-polymer;
- acrylic;
- silicone and silicate.
The classification is based on the binder component. The first type is produced in the form of dry mixtures. Distinctive feature This option is low cost. Other types are sold already in the form ready-made compositions, which only need to be applied.
Scope of application of Lamb
Like other types of plasters, Lamb is used for finishing works. As noted earlier, it is well suited in cases where the surface is uneven. It can be used to cover both external and internal walls.
Unlike standard plaster, lamb can create an original surface. Therefore, it is popular for decoration.
The material is so durable that it can last operational period even old walls. The coating is vapor permeable. Lamb is not used for finishing floors and ceilings.
Preparatory work
Before applying the plaster, it is necessary to collect the tools that will be needed to carry out the work. Masking tape is used to protect the untreated surface. The material will be applied using construction spatulas.
The mixture is prepared in a bucket. 
It will be difficult to work if your hands get dirty, so you should protect them with gloves. The material hardens quickly. So that the tools can be used in further work, they should be cleaned immediately with a cloth.
If you plan to perform a colored finish, paint is used, the surface of which will qualitatively protect the plaster. Before facing works, the surface needs to be prepared. This is done by stripping. It is important to ensure the same level of cleaning of paint, or other materials that may peel. After the surface is cleaned, it is necessary to coat it with a primer if the wall is located outdoors. There should be no marks on the surface. The lamb sticks well on various types of walls:
- brick;
- plasterboard;
- cement.
The mixture will also adhere to other materials, but it is better to consult a specialist.
Application technology
Cladding work is carried out within positive temperatures from 5 to 30 degrees Celsius.
The material is manufactured according to the composition indicated on the packaging. Usually it is enough to mix the purchased mixture with water. The ready-to-use material resembles a paste. You can stir the paste construction mixer or an electric drill. You need to stir in several stages. The interval between them is up to two minutes. Application is carried out using a stainless steel trowel.
The plaster will stick to the wall if it is glued to it rather than soaked in. This can be ensured if the surface is treated with acrylic primer . It should have a common tone with the plaster. You cannot finish the walls if the primer has not yet dried. To prevent the mixture from freezing in the bucket, it needs to be stirred from time to time.
The layer of applied material must be equal to the thickness of the granules.
The mixture can be structured in just 15 minutes. Therefore, it is not recommended to apply more than one square meter at a time. After the specified period has passed, it will be difficult to level it.
If the plaster is applied over a shorter period, the mixture must be given time to harden. Do not interrupt the application of the mixture. When smoothed with a grater, a characteristic structure is formed, similar to lamb's wool. If used different mixtures, they must be of the same quality.
The surface is leveled using a spatula. It is necessary to carefully run the spatula over it until excess plaster collects on it. If the residues have not hardened, you can remove them using a wet cloth. If they are frozen, cleaning is carried out with a special metal grater for cleaning tools.
To paint walls finished with lambswool, you will need a roller or a wide brush. To extend the service life of the walls, you can apply wax.
Advantages of decorative plaster Lamb
The material is available in a wide variety of colors. Thanks to this, additional painting is not necessary.
Among other advantages of the material are:
- resistance to frost and water;
- simple method of application;
- additional strengthening of walls;
- preventing condensation formation;
- resistance to mechanical damage;
- ability to withstand heavy loads.
Lamb is fireproof building materials. Plaster goes well with various types design, and is able to withstand aggressive atmospheric environments and low temperatures.
The surface of the “lamb” plaster has an obvious resemblance to the cover of an animal. The fine-fleece texture creates the impression of the nobility of the hand of the creator, who uniquely painted the surface, and skillfully hides in the shaded curlicues the modest construction skills of the households of the country estate.
Components of the plaster mixture
Peculiar surface structural plaster lamb is obliged to mineral inclusions with grain size:
- 1 - 1.5 mm. A perfectly flat surface is required for application. The deviation from the plane should not exceed 1 mm. Otherwise, the depressions will be filled without creating the desired relief. The mixture is intended for use indoors, where absolute leveling of the walls is expected;
- 2 - 2.5 mm. By analogy with the above description, it does not require careful preparation of the surface before applying lamb plaster. Most often used for finishing external walls. In this case, water-repellent agents are added to the composition. Water-absorbing ingredients, on the contrary, are removed and replaced with polymer materials.
Minerals of a similar grain fraction are used as fillers: dolomite, quartz, marble. This leads to a homogeneous composition.
Lamb wall plaster is suitable for finishing:
- bricks;
- concrete;
- gypsum;
- plywood;
- polystyrene.
The binding elements of the mixture, after being applied to the surface, together with the fillers, envelop the microcrystals of the base and, when dry, form a strong connection of dissimilar structures.
Technology of applying lamb plaster
Preparatory work consists of a number of sequential operations:
- leveling the surface in a plane. A slight roughness commensurate with the grain fraction of the mixture is allowed;
- priming the base. It is made with a product adapted to a specific mixture. Before purchasing, you should familiarize yourself with the characteristics of the composition. Expense for square meter, combination with the treated base, toxicity is the main thing you should pay attention to;
- dividing the wall being treated into zones for continuous laying of the mixture. Practice has proven the possibility of applying plaster before hardening to an area of 1 to 1.5 sq.m. Next, a new bookmark is made, then the next one, and so on until complete completion. A visually visible strip is formed at the junction of the zones. If you divide the boundaries by wall elements: pipe, window hole, door, corner, the eye will not notice a slight difference in color.
It will take about 5 hours for the primer to dry. During this time, tools and equipment are prepared, and plaster is mixed. The mixture is applied with a spatula or grater. Initially, the instrument is held at an acute angle to the wall. As a result of smoothing movements, a thick layer of plaster is applied to the selected area and reduced to grain size using scraping movements. The structuring of the pattern occurs during smoothing movements of the grater on the drying surface. After final drying, begin painting.
The “lamb” will hide with its “fur coat” minor miscalculations of the owner of the house, demonstrating his abilities favorably.
Acrylic plaster - perfect option for those who want to save on facade finishing.
The products are made on the basis of acrylic resins, which allows you to obtain durable coating, resistant to mechanical and natural influences. Guarantee period operation acrylic plasters- at least 10 years. But to achieve such indicators, it is necessary to select the correct composition, prepare the surface and apply the product, observing all technological requirements.
The plaster has excellent adhesion to any mineral substrates, such as concrete, cement-sand, cement-lime and lime plasters, brickwork, drywall, etc.
Our specialists and technologists will help you choose facade plaster and primer, taking into account the characteristics of the walls of your home, insulation and climatic conditions.
Ready to apply
Prevents the formation of microcracks
Available in 2500 colors
Solvent-free, environmentally friendly
High grip
Documentation
Working conditions
Do not apply directly solar radiation, during rain, strong winds and air or surface temperatures below +5 ° C, and relative humidity air above 80%.
The base must be level, dry, sufficiently strong, free from contaminants and substances that reduce adhesion (dust, grease, lubricating oils, bitumen mastics, fragile paint coatings and so on.). Unstable, crumbling areas of the base should be removed. Before applying plaster, treat the base with a layer of Farbeⓝ Quarzgrund
Execution of work
Before use, the contents of the container should be mixed thoroughly. Apply with a stainless trowel or plastering machine to the grain size. After the applied plaster stops sticking to the tool, the texture is formed using a plastic grater. The “Lamb” texture is formed by small circular movements of the grater directed in one direction, usually counterclockwise. The grater is held parallel to the surface being processed. Work on one surface plane should be carried out continuously “wet on wet”. To obtain the required texture, it is necessary to clean it as often as possible. work surface grater from excess material without returning it back to the container. Dilution with water up to 2% is allowed. During the period of formation of the surface structure and drying of the plaster, it should not be sprayed with water.
Textured plaster Lamb for finishing the facades of the house. Finishing the facades of buildings is an important matter during renovation or at the final stage of construction.
There are many options. Entire systems for constructing facades have been developed, from simple designs to complex complexes.
All activities are reduced to one goal, the materials used for finishing outside walls, must perform complex tasks.
All such tasks can be accomplished with Lamb textured plaster. It has been tested by many years of experience. Except positive feedback to your address this material has no other information.
Plastering
Composition of the mixture for the production of textured plastering
- The finished mixture is produced on the basis of M400. In modern compositions, cement is replaced with acrylic resin or on a silicone base.
- Add crushed to the base granite chips. The size fractions range from 1 mm to 4 mm. The percentage of crumbs in the composition is increased to 85 units. This allows you to obtain an even textured layer with the required pattern.
Fact! Textured plaster Bark beetle is, in principle, identical in composition to Lamb, but the percentage of crumbs in the mixture is 40 units. This is necessary to produce furrows along the main binder layer. This surface looks like wood eaten by a bark beetle.
- Coloring pigments are added when making the mixture. Initially, the composition has a gray or whitish color, which corresponds to the base. Alternatively, painting can be done after the material has been applied and dried to the walls.
Surfaces suitable for applying Lamb plaster
Textured plaster has no special opposition from basic materials load-bearing walls. A layer of this mixture is applied only to the base layer ordinary plaster. As a conclusion, we can conclude that Lamb plaster is applied to a flat surface with a cement base.
The only one an important condition is the need to use plaster mesh when applying the base coat. on the surface of decorative plaster are not only clearly visible, but can accumulate unwanted moisture. Under the influence of frost it leads to the destruction of the material.
Surfaces to be plastered:
- Reinforced concrete wall slabs.
- Ceramic masonry or ceramic blocks.
- Wall blocks made of foam concrete or
- Wall surfaces are pre-finished with insulation made of mineral wool slabs or expanded polystyrene slabs.
Preparing the surface for applying decorative plaster;
How to prepare the Lamb mixture with your own hands:
- The dry mixture is poured into a container.
- Water is added gradually.
- The composition is stirred with an electric mixer to obtain an even, homogeneous mixture. The consistency of the material should resemble thick sour cream.
- If you decide to use color, it is necessary to add coloring during the process of mixing the main ingredients.
Important! To obtain a uniform color in batches of different times, it is necessary to divide the dye into equal parts and add an equal part of the pigment to the same amount of the mixture. The new composition is mixed in a clean container. This must be taken into account to avoid adding tone from the previous batch.
How to properly apply the finished mixture to the surface
To work, you need to prepare a rectangular steel trowel, a plasterer's trowel, a wide paint brush, a roller for applying a textured pattern, a polyurethane float for leveling the surface, and scaffolding for performing work at height.
The process itself consists of simple steps:
- The finished surface plastered with a base layer is treated with a primer to remove dust.
- The solution is applied with a trowel to the lower third of the wide part of the trowel.
- The tool with the material is positioned relative to the wall surface at an angle of 45 0. By lightly pressing the trowel, it is necessary to apply the plaster to the wall in a layer equal in thickness to the size of the grains in the material. Work is carried out from bottom to top. It is immediately more convenient to apply the solution to an area of no more than 2 m2. This method will allow you to work with the material to level and grout the surface until it sets within 10 minutes. To obtain a simple, flat surface with a classic lamb skin pattern, rub the surface with a polyurethane grater in a circular motion with light pressure.
- Then the next square is covered.
Interesting! To give a special surface pattern, you can use textured roller. The depth of the pattern is chosen relative to the thickness of the layer. The surface can also be refined with a simple shoe brush. A unique pattern is applied using circular movements. In case of an error, corrections are made with a wet paint brush.
Conclusion
When choosing decorative material It is better to use proven mixtures with a base of simple cement. This material is simple, reliable and not expensive. New resin-based materials do not differ in quality from the classics. But their cost is much higher.