Mats for pipes. Mats for a warm water floor: recommendations for choosing and how to lay mats under a warm water floor

Important condition proper functioning of a warm water floor - the use of thermal insulation, which reduces energy costs and avoids heat loss.

The most modern and comfortable view insulation are mats for warm water floors, presented in a wide range on the construction market.

It’s sometimes quite difficult to understand the variety of thermal insulation materials, isn’t it? Each manufacturer tries to demonstrate best sides of their product, sometimes keeping silent about possible shortcomings.

We will help you choose optimal solution for insulation of water floors. The article describes different types mats based on polystyrene foam, given practical advice according to their selection and installation. We also identified manufacturers whose products have won the trust of consumers and are in active demand.

When arranging a water heating system, the most important task is to minimize heat losses and direct all the heat directly to the room where the structure is installed.

If you simply lay pipes on the main floor, then there will be very little use from this system, since most of the thermal energy will go down to the basement or to the neighbors on the lower floor.

Thermal insulation is precisely designed to solve this problem, which, on the one hand, is a barrier to the entry of cold air from the basement (if the system is installed in a private household), and on the other, serves to preserve and distribute heat evenly throughout the room.

Properly selected and installed thermal insulation allows you to eliminate the loss of thermal energy and redirect the warm flows coming from the heating pipes upward, towards the room. In addition, the insulation prevents condensation from accumulating and prevents the formation of mold on the walls

The classic types of insulation that were widely used in the past are ecowool and polystyrene foam. Actually, even now the inexpensive cost of these materials still attracts very thrifty buyers.

However, progress does not stand still, and manufacturers offer more practical and convenient ones - special mats for water floors.

Features of the material for the production of mats

Modern mats are made from a material that not only has excellent heat-insulating properties, but also has a whole list of other advantages.

Main advantages:

1. Low vapor permeability(0.05 mg (m*h*Pa). For comparison, for mineral wool this figure is 0.30. This means that polystyrene foam does not allow water vapor to pass through well and does not accumulate moisture, is constantly in a dry state, and as a result does not contribute to the formation of condensation.
2. Low thermal conductivity, which means maximum heat retention in the room.
3. Soundproofing characteristics.
4. Does not attract rodents and is not a breeding ground for the formation and development of microorganisms.
5. Durability. According to the results of the tests (alternating high and low temperatures from plus 40 to minus 40 degrees and exposure to water), the service life of products made from this material is up to 60 years.

The mats use expanded polystyrene with a density of up to 40 kg/m 3, so they can withstand heavy loads perfectly.

This property is especially valuable when, since a fairly heavy structure consisting of water pipes, concrete layer and finishing flooring.

Weight of the water heated floor system per 1 sq.m. is about 200 kg, the thickness of the layers is approximately 150 mm. The main load falls on the bottom layer. The high density of polystyrene foam ensures the strength of the mats and allows them to support a heavy structure (+)

The main advantages of using mats

Mats for watermen heating structures- modern thermal insulation material, manufactured in accordance with accepted European standards for quality and safety.

The slabs are produced using latest technologies and combine all the advantages of traditional insulation materials, and at the same time are devoid of their inherent disadvantages.

Advantages of mats:

• have excellent performance characteristics;
• have good thermal and sound insulating properties;
• suitable for both semi-dry installation and wet screed;
• with prolonged use they do not deform or change size;
• equipped locking system, thanks to which the slabs are quickly and easily laid;
• most mats have markings, which greatly simplifies the pipe installation process;
• do not rot, resistant to bacteria;
• do not swell from exposure to water;
• safe for humans, under normal temperature conditions they do not emit harmful odors;
• withstands both high (up to +180°C) and low (up to -180°C) temperatures;
• have a long service life of up to 50 years.

It must be taken into account that untreated polystyrene foam is a flammable and fire-hazardous material and emits toxic smoke when burned.

To reduce this property, fire retardants are added to the insulation during production, which makes it a self-extinguishing material. In products domestic production such material is marked with the letter “C” at the end.

Types of polystyrene foam boards

There are four types of mats that are suitable for use when installing water floors. Each of them has its own characteristics and is intended for installation in certain conditions.

Types of mats:

1. Rolled materials equipped with a foil layer.
2. Expanded polystyrene boards.
3. Panels made of expanded polystyrene with foil and film coating.
4. Profile mats with bosses.

The choice of a heat-insulating coating depends on the parameters of the room, the base on which it is installed, the dynamic and mechanical load that the insulation must withstand. The slabs have different heights, therefore it is also necessary to take into account the thickness of the future screed.

Rolled foil insulation

Insulation in rolls is made from penofol with a thickness of 2 to 10 mm. On one side, the material is covered with aluminum foil or polymer film, the function of which is to direct the heat flow and distribute heat over the entire floor area.

This type of heat-insulating material can be classified as mats very conditionally, since it has low thermal insulation properties. This causes a rather limited scope of its application.

Foil insulation is used only when a water floor is used as an additional heating system and the main floor already has some degree of insulation.

Roll insulation is the simplest and most inexpensive type of thermal insulation, but it can only be used under certain conditions

It is not advisable to lay rolled material on the first floors of buildings and in rooms below which there are unheated areas, since the insulation efficiency in this case will approach zero.

Installation on this heat-insulating material poses a certain difficulty. It is required to use additional fasteners: staples, clamps, reinforcing mesh, etc.

When laying the covering, the sheets are placed end-to-end with each other; to ensure better sealing, the seams are taped with special foil tape.

However, despite the very modest characteristics, insulation in rolls under certain circumstances is the only possible option insulation, for example, when low altitude premises, when every centimeter of space counts.

Polystyrene foam insulation boards

Flat polystyrene foam mats can be used as thermal insulation for a water floor. The simplest and cheap option– regular foam, more durable and high-quality insulation– a plate made of extruded polystyrene foam.

If you decide to go with more affordable polystyrene foam, then when purchasing it you need to focus on the density of the material. This figure must be at least 35 kg/m3. At lower strength values, the insulation may not be enough to support the load of the heating system.

It is more preferable to use the second option, which has higher quality indicators. The best representative of this series is. It has a closed cell structure, is durable, and can withstand loads well.

To improve the thermal insulation characteristics, foil insulation in rolls can be laid on top of the mats.

Image gallery

Comfort residential buildings is increasing all the time, to a large extent this is facilitated by such an innovative solution to the heating system as “warm floors”. The heat coming from the floor creates in the room special atmosphere habitability and comfort.

The modern market offers several basic varieties of such floors, and the water one is structurally the most promising model.

To equip it you will need pipes that ensure the movement of the coolant and additional components, increasing the overall efficiency of the system. To simplify installation and make it convenient, use mats for insulation.

The functional effect of a water floor depends on how well and technically correct the installation was. thermal insulation system, as well as on the correct laying of heat pipes on top of it.


It makes no sense to abandon it, since then most of the energy will go to heating the floor slabs or foundation. Thermal insulation helps adjust heat flows in the required direction. If the heat goes up, unnecessary energy consumption is prevented.

It is also important that the mats take on a fairly large load. It consists of the weight of the pipes themselves, which are filled with a coolant, the mass of the screed closing the pipeline, the finishing floor covering and dynamic external loads, which are inevitable after the start of operation.

The material used to create the substrate must be very dense in order to resist and not deform. Its minimum permissible density is 35 kg/m³.

Kinds

There are several types of mats.

Foil

Made from foamed foil polyethylene. They are used in cases where the floor is laid as an addition to the central heating system. The specific name of the material is penofol, which is covered with a layer of foil on one side.

It is laid with foil to the top, and placed on it heating pipes. Similar products unsuitable for arranging a warm water floor if the housing is on the ground floor and there are basements. There is no point in using them in the renovation of a private one-story house..

Under such conditions, their efficiency in terms of heat conservation is minimal, which means the entire system will be ineffective.

To secure such mats, you need to purchase additional fasteners., for example, a large-mesh metal mesh, a set of clamps, clips or staples.

With film

They can also be classified as foil substrates for water heated floors, they are made of polystyrene foam, but it is high-density, from 30-35 kg/m³.

The product also includes a layer of foil and a layer of polymer film With protective function. This film has special markings that will help when laying pipes. This type of mat is quite effective as a heat-insulating material.

The density is such that the brackets for securing the pipes are held very securely. A screed will fit well on top of such a substrate., which is not will crack grasping.

Mats with film are used to create a heated floor where it will be the primary source of heat. Additional system lamellas provide excellent styling, so the heat is retained for a long time.

Flat polystyrene foam

One of the best thermal insulation mats for water heated floor. Their thickness ranges from 40-50 mm, which allows them to be used as a substrate. An important parameter is and high density, from 40 kg/m³. Perfect for rooms where the floor is planned to be the only element of the heating system.

The material is practically not subject to wear and deformation. Pipes are attached to them using special plastic fasteners. The downside is that before laying the pipes, the master must apply the markings with his own hands.

After laying, the substrate is covered with a layer of polyethylene, to prevent chemical reaction at the moment of contact of sheets and cement-containing screed.

With bosses (profile)

The most used model of polystyrene foam backing. They are made using the hydropellent stamping method, as a result of which bosses appear, peculiar protrusions that are located in even rows on the surface of the product.

Lugs make it possible to quickly lay pipes until test crimping and filling with screed. High-density slabs for heated floors have square shape and thickness from 10 to 35 mm. The projections are low, about 25 mm in height, usually cubic or cylindrical, and a pipe can easily fit in the space between them.

The pipes are securely fixed and do not move when poured with finishing screed. They are produced with or without laminate, the first ones have a layer of vapor barrier film coating on top.

Characteristics of expanded polystyrene

Its density should be 40 kg/m³ so that the products can withstand various mechanical loads. Expanded polystyrene has low thermal conductivity, it is only 0.037 to 0.052 W/m×K. This is necessary for good thermal insulation.

Products with bosses are able to absorb sounds and noise. Standard rate noise absorption is 24 dB with a layer thickness of 20 mm.

Reliable waterproofing is provided by the laminate and centering fasteners located at the ends of each panel. They are the ones needed to lay out a continuous surface of individual elements. Profile mats for water heated floors adhere perfectly to each other, and this eliminates the possibility of the formation of seam gaps. Standard parameters slabs - 1.0 × 1.0 or 0.8 × 0.6 m.

Benefits of using mats

If the mat is installed correctly, it can serve as an excellent soundproofing material. But there is an important nuance - water heated floors must be absolutely safe for those living below. Therefore, along with reliability and durability, such a criterion as waterproofing is valued. And this same layer is designed to protect the substrate itself from destructive effects. cement mortar floor.

There is a non-professional opinion whose supporters talk about the possibility of abandoning mats when laying floors. But this position is erroneous, since heat losses will be so great that they will inevitably lead to significant financial losses.

If we consider the cost of all water floor systems as a whole, then the price of insulation is not so high. A a design made once and wisely will pay for itself one hundred percent during operation.

Laying

1. All parts must be connected to each other. And under the sheets, regardless of their type, there must be a backing made of waterproofing film;
2. Along the perimeter of the floor at the edge of the wall waterproofing film is fixed using damper tape;
3. Plates are laid on top of the waterproofing, mats for water heated floors made of foam board must be fastened together using locking mechanisms provided at the ends. If the weight and thickness of the insulation allow, then the slabs can be additionally fixed with glue;
4. It is strictly forbidden to use nails for fastening and so on, since this violates the integrity of the product and greatly reduces its strength;
5. Smooth plates without provided fastenings are laid very tightly and sit on a glue “pad”. Foil products are glued with tape to achieve complete tightness;
6. Once the sheets are fixed - start marking and laying the water circuit;
7. The final stage – finishing coating for heated water floors.

Prices and how to choose

The heat and energy savings speak for themselves, making water floor mats a well-reasoned purchase:

• Before purchasing a backing, you need to ask the seller for all documents, certifying not only the quality of the product, but also confirming its fire safety and environmental standards. Mats without such documents may be counterfeit famous brand and will be unable to withstand the expected loads;
• It is better to choose those products that have a laminating layer– this is a guarantee of additional insulation. This coating adheres perfectly to both semi-dry and wet screeds;
• The thickness of the mat is chosen taking into account the thickness of the screed itself And finishing coating. It is necessary to pay attention to the thermal insulation in the room, since many ceilings already have a similar layer.
• Sometimes the design of a warm water floor allows you to purchase mats with bosses that do not have thermal insulation qualities. But in this case, their only advantage is the reliable fixation of the pipeline system.

average price for mats for warm water floors:

• REHAU, Germany: from 800 rubles for one product.
• OVENTROP, Germany: from 100 rubles (roll substrate) to 1200 rubles for one product;
• Energoflex, Russia: from 20 rubles to 70 rubles for one product.

Choose only high-quality pipes for water supply in a private home! Which - .

If you use water from a borehole or well, you definitely need to install filters in a private house, read about it.

Take care of the uninterrupted supply of water to your home by installing a reliable pumping station water supply More information .

Once the decision has been made to create a water floor, you need to carefully consider all the small details and nuances of working with this system. The purchase and installation of correctly selected mounting mats for water-heated floors will help you save considerable amounts when heating your own home.

To make your home comfortable, it is worth purchasing mats with suitable characteristics. Manufacturers offer products of various sizes, which allows you to make a choice in favor optimal option. We suggest you figure out why such plates are needed, and which model is better to give preference to.

Leading manufacturers of mats for laying water-heated floors

In order not to doubt the quality of the purchased mats for laying water-heated floors, you should choose products from leading manufacturers. We advise you to pay attention to the products:

• Oventrop , demonstrating high performance characteristics. The German company offers mats with “bobs” for dry installation, roll and folding thermal insulation. The first type can be with or without thermal and sound insulation;
• Knauf. The manufacturer offers quality slabs with high performance characteristics;
• Rehau. Despite the price, mats for warm water floors made in Germany are in steady consumer demand. The most popular are foam styrene mats with “bobs”. Supplied with clamps for fastening pipes;
• Energyflex. The domestic manufacturer offers a wide the lineup, in which you will definitely find suitable option for water heated floors;
• Ecopol. The Russian company offers smooth mats and those with bosses. The interlocking connection and the presence of a waterproofing layer ensures the formation of a strong and reliable basis. The level of thermal insulation characteristics depends on the thickness of the thermal insulation layer. The latter can be 20, 30 mm or absent in principle.

Which mats are best to buy for warm water floors: popular models

If you have not yet decided which mats for a warm water floor in your home are best to buy, we suggest you get acquainted with the models that are especially popular among consumers. Perhaps you will find a suitable option among them.

Expanded polystyrene mats for heated floors Knauf Industries

The size of one mat for Knauf INDUSTRIES underfloor heating is 1200 mm × 600 mm or 0.72 m². Lugs big size and a special configuration allow you to reliably fix the heating circuit with pipes with a diameter of 16 mm or 20 mm. For proper fixation of the elements relative to each other, a double lock is provided, located around the perimeter of each mat. The presence of markup makes it easier to execute installation work.

Knauf Industries

Clamps with lugs Rehau Varionova

The German company offers mats for warm water floors Rehau, the price of which is fully correlated with their quality. The size of the polystyrene panels is 1450 mm × 850 mm × 24 mm with design dimensions of 1400 mm × 800 mm. Laying a water circuit with a diameter of 14–17 mm can be done in increments of multiples of 50 mm. The formed layer can withstand loads of up to 60.0 kN/m².

Foam shield WF 16-50

High-quality products that can become a worthy competitor to foreign analogues. For the production of mats for water heated floors “Penoshchit”, polystyrene grade PSB-S 35 with a cellular-porous structure with a density of 21–25 kg/m³ is used. Thanks to this, the slabs provide a sufficient level of thermal insulation. The laying step can be a multiple of 50 mm. Suitable for pipes with a diameter of 16 mm. The size of the slabs is 1000 mm × 1000 mm × 50 mm.

A carefully thought-out design, combining protrusions and openings, guarantees reliable fixation of water heated floor pipes. The products allow you to securely fix pipes with a diameter of 16 mm without additional fasteners. Base 30 mm. This is enough for thermal insulation of the laid coating.

Mats for heated floors - foil, film and profile

5 (100%) votes: 2

Now we will look at the types of mats for heated floors and what advantages they have. There are also some of our tips on which floor mats to buy, as well as installation tips at the end of the article.

How correctly will it be distributed? thermal energy, heating productivity directly depends. In a heated floor system, effective distribution is determined by heated floor mats.

You can find out the price and buy heating equipment and related products from us. Write, call and come to one of the stores in your city. Delivery throughout the Russian Federation and CIS countries.

Heating mats require installation thermal insulation material on concrete. At the moment, the most popular material for these purposes is polystyrene foam.

Heated floor mats with bosses

They almost completely eliminate heat loss and ensure that heat only goes upward. They must be resistant to mechanical stress so that the system does not fail. At the same time, it is important to take care of the waterproofing protection of the mats.

You can determine the functions of the waterproofing layer located under the mats:

1. Protection from adverse influences.
2. Reliability of the floor covering.
3. Safety from leaks on floor slabs for neighbors living in apartments below.

When the installation has been carried out correctly, the mats additionally soundproof the room.

Expanded polystyrene mats and their varieties

Expanded polystyrene must also have certain characteristics for the heating system to work efficiently:

1. Firstly, the density of the material should be 40 kg per 1 m³. Only then will the system be resistant to heavy loads.
2. Secondly, the material practically does not conduct heat, therefore it ensures minimal heat loss.
3. Due to the cellular structure and other physical characteristics expanded polystyrene creates excellent sound insulation.
4. From external influences protects the laminated coating and centering locks located at the ends of the panels. Due to the good adhesive properties of the mats, the occurrence of gaps is almost impossible.
5. The installation pitch and mat sizes may vary.

Mats for heated water floors expanded polystyrene have their advantages:

• They are made according to European standards quality. Self-extinguishing raw materials are used during production.
• Wet and semi-dry screed can be laid on top of polystyrene foam.
• They do not deform, since the material is quite durable.
• They have clamps that make it possible to quickly install the pipeline.
• Installation of the heating pipeline is done according to markings applied to the surface. This promotes rapid distribution of heat energy in the room.
• Excellent physical characteristics.
• As mentioned above, they are characterized by sound insulation and thermal insulation.
• Do not harm the human body.
• They are not subject to rotting, do not allow moisture to pass through and do not swell.
• Fireproof and withstands minus temperature 180 °C and increased to 180 °C.

Mats, which are produced individually for laying pipes of a heated floor system on them, are a convenient solution. The slabs have bumps (bobs) on the surface. It is easy to pass pipe turns between them.

Expanded polystyrene boards can be as follows:

1. Extruded (XPS).
2. Pressless (PSB).
3. Press (PS).

They can also be smooth, embossed, foil or non-foil.

Let's take a closer look at each type.

Foil mats for heated floors

Can be executed and contain mineral wool, polystyrene, basalt fiber, foamed polyethylene, etc. On one side the mats cover. It has different thickness(depending on the type of product). If these are slabs of foamed polyethylene, then the thickness will be from two to ten millimeters. If the slabs contain basalt fiber, then the thickness can range from twenty to one hundred millimeters.

During installation work, the mats are laid with foil facing up (for better heat reflection).

Foil plates with polyethylene foam are rarely used for installation on the first floors, where the house also has a basement. IN in this case Basalt fibers are often chosen.

Foil mats with basalt fiber

Film mats. Very durable polystyrene foam is used in production. The outside of the slab has foil on one side and is covered with a film of polymers.

A coordination mesh is applied to the surface of the film, which makes installation of the heating circuit easier. This allows you to save time on installation and do it yourself.

The good density of the material allows for sharp staples for fastening flexible pipes hold firmly.

The film over the foil is needed to protect the mirror reflective layer from the chemical rejection of the concrete, which comes into contact when pouring the screed on top of the thermal insulation.

Energoflex mats Energofloor Tacker

Profile mats. On the Internet you can even find such a name as mats for heated floors with bosses.

They are specially designed for installing underfloor heating pipes and are currently the most convenient. They are also made from expanded polystyrene, only using the hydropellen stamping method. This makes the mats very dense and reliable for holding the shape of the pipes. Bosses are elements that are located on the upper plane.

Mounting mat Rehau Varionova

They can be in the form of a cylinder, parallelepiped or other shapes. The convexities are at such a distance from each other that the pipe is fixed very firmly and does not require additional elements fasteners The contour will not move when laying and pouring the screed.

A mat with bosses for heated floors is a structure made of high-strength polystyrene foam, so it can withstand dynamic and static loads. Such slabs are produced without coating, but still the best solution There will be a purchase of products that are covered with a strong polymer film.

Another advantage of profile mats is the ease of pipe laying. Installation can be done manually without outside help. To do this, you just need to carefully insert the pipes into the spaces between the bulges.

Expanded polystyrene mats Knauf Therm Warm floor

Mats for heated floors with clamps are inexpensive, but it is still worth considering a few recommendations so that you do not have to purchase low-quality products and be disappointed:

1. If you are faced with a choice of which design to purchase, definitely buy boards with a foil and laminated surface. You won't have to worry about waterproofing, and the heating system will work more efficiently.
2. Pay attention to the parameters: pipe diameter and laying step on the mat.
3. How thick the insulating part will be depends on the level of insulation of the floors. Consider the thickness of the screed and the final floor covering. If the floor does not need special insulation, then you can buy profile mats for heated floors with bosses minimum thickness and with a weak layer of thermal insulation, i.e. Only for light laying of pipe circuits.
4. There are many manufacturers. And in order not to make a mistake with your choice and purchase quality products, it is better to choose a trusted seller.

Laying mats

Laying of heated floor mats, whatever it may be, takes place in mandatory over waterproofing. The waterproofing can be a film coating of the surface of the subfloor or something else.

Bracket (harpoon) for attaching heated floors

They are fastened with locking joints. If there are any. Sometimes it may be necessary to fasten the structure to the floor if the mats are light and thin. This can be done with glue. Metal fasteners should not be used, as the floor waterproofing and other properties of the mat may be damaged.

If flat mats are installed that do not contain locking joints, then they can also be attached to the floor using glue.

There are many installation nuances, it all depends on the type of structure and its characteristics.

The pipes are laid after the warm mat has been completely laid.

Installation has its own characteristics. Before laying mats under a warm floor, several points should be completed. It is necessary to calculate the heating power (measured in Watts per 1 m²) and the area for the material. Then it’s worth deciding what the installation piping diagram will be. Schemes can be of the following types:

1. Spiral-shaped - suitable for rooms with a small area.
2. In the form of a double spiral - suitable for large rooms.
3. Serpentine - in this case, the pipes are mounted parallel to each other.

Review of manufacturers

When purchasing a mat for underfloor heating, it is important to pay attention to long-established manufacturers. Currently popular are Oventrop, Energoflex, Rehau.

Oventrop is a manufacturer from Germany that produces polystyrene foam mats. Its popular models are as follows:

• NP-35 is a version of the slab with bosses, which have excellent sound and thermal insulation properties. On one side the mats are covered with polystyrene film. They are used with conventional screed and self-leveling floors.
• WGL-045 is a version of the slab in the form of a roll; they are covered with polypropylene film. Used for pipes with a diameter of 1.4 and 1.6 cm and a laying pitch from 5 to 30 cm. Roll area 10 m².

Energoflex is domestic manufacturer, releasing quite quality material. Its popular models are as follows:

1. Expanded polystyrene board. The bosses of the structure are 2 cm, they make it possible to lay pipes without additional accessories. The model has self-centering locks and applied markings. Mounted in 5 cm increments and designed for pipes with a diameter of 1.6 to 1.8 cm.
2. Energoflex TP. This is a version of polystyrene foam foil mats that have a coordinate grid on the surface (step is 50 mm).
3. Energoflex Super TP is a variant of mats for heated floors. Foil models, with coordination grid and in increments of 5 cm.

Rehau is a manufacturer of polystyrene foam insulation boards from Germany. Mats with clamps for heated floors have a polystyrene foam soundproofing and thermal insulation layer three centimeters thick.

Mats for heated floors are thermal insulation a design that allows you to create a favorable microclimate, comfort and coziness in the house. You should not save on insulation material and buy fakes that do not have a certificate. Most the best option– purchase polystyrene foam boards, individually made for heated floors.

The ranks of those who decided to install heated floors in their home for heating water based, are constantly replenished. This technology eliminates the usual batteries and involves installing heating pipes under the floor surface. In fact, it turns out that the floors warm the room, distributing heat evenly throughout the house. It is recommended to decide on this issue already at the stage of drawing up a repair plan. It is also recommended to buy mats for warm water floors in advance.

Advantages of a warm water floor

Design versatility. The elements of such heating do not decorate, but do not spoil the interior decor; they are invisible and neutral, unlike, for example, traditional radiators.

Saving. Warm water floors give the air temperature a couple of degrees lower radiator heating. Such a slight discrepancy will not affect comfort, but will provide tangible savings in the range of 6-12%.

Microclimate. The house is heated optimally. Mats for warm water floors, the price of which may vary, hold comfortable temperature. The air does not overheat, but remains warm enough. Your feet/hands don't get cold, and your body doesn't get hot.

Easy to use. IN warm floors water-based there is no high-tech equipment, they consist of simple elements. There is no need for regular maintenance.

KNAUF floors

When the decision to install warm water floors has been made, you need to ensure the quality of its elements and the correct combination components. KNAUF floors based on polystyrene foam have a high thermal insulation value in heating system KNAUF Therm.

1. floor base;
2. KNAUF Therm plates;
3. pipe;
4. KNAUF building mixture for leveling screeds.
5. tile adhesive, lining for laminate;
6. floor surface;

Features of KNAUF Therm floor elements

Special polystyrene panels KNAUF Therm have a special design that provides the most effective application in warm floors.

External surface of the panel:

• especially strong bosses located along the contour of the pipe with a diameter of 16-20 mm;
• special fastening for quick and easy installation around the perimeter of the mat;
• a special shape of the boss with a flap inward, designed for reliable and simple fixation of the pipe.

Inner panel surface:

• practical markings that virtually eliminate unevenness and minimize waste when cutting the floor;
• a plate with the KNAUF logo, which serves as a guarantor of the authenticity and quality of the product.

Return