Slippery steps in winter what to do. Slippery tiles - how to make them non-slip

We are asked:
IN country house the previous owner built a staircase to the second floor (rotary, 180%, with winder steps). During operation, it turned out that the coating is very slippery, especially for children. Please tell me, possible options eliminate dangerous inconvenience.

We answer:
There are many options:

Installation of special strips or corners on the edges of steps. They are a profile made of aluminum or galvanized with a glued strip of rubber. Sold in construction stores.

Cladding the steps with ceramic anti-slip tiles (used when cladding porches, some samples even neutralize light icing).

Laying carpet on the steps (carpet, plastic). It is fastened with special fasteners, they can be the most different designs. For example, on the back edge of the tread, where the riser of the next step begins, i.e. in the very corner, rings are installed into which a metal rod is passed. The rod is secured either with a decorative nut or some kind of lock. A carpet runner is laid along the entire length of the flight, and so that it does not get confused or slide, you fix it on each step, pressing it with such rods. Fastenings for carpet runners on steps can be seen in a wide range in large construction supermarkets. Depending on the type of steps, the fastenings can be placed in other ways, for example, on the risers or even on the sides of the steps.

You can lay a separate small “mat” on each step (material: carpet, plastic, rubber, silicone, etc.) and secure them with screws with decorative overlays. A wide selection of such overlays can be found in stores that sell furniture fittings.

The simplest option is to varnish the steps with the addition of fine clean sand. Of course, the sand must be thoroughly washed and of a fine fraction, ideally quartz (it is translucent). Alternatively, cover it with varnish (and you can do this under some kind of pattern to get an ornament), and then, while the varnish is still wet, sprinkle it fine sand. If you take colored sand, and even different colors, you can get quite interesting decor. When the varnish dries, the excess sand is swept away, and the stuck grains will provide the steps with a “rough” appearance. Instead of varnish, you can use some kind of glue (acrylic, epoxy, or at least a regular PVA emulsion).

You can apply a design to the steps using oil paint, to which again add sand.

Of course, with varnish, paints and sand, it is better to experiment on smooth wooden planks first.

Ask a question or comment

How to make stair steps non-slippery
How to make stair steps non-slippery.

What to do to prevent the porch and steps from slipping in winter

In what ways can you effectively and quickly solve the problem of slippery steps and porch stairs today? Especially in autumn and winter, when smooth surfaces become especially dangerous. Of course, this means the use of all kinds of anti-slip devices and coatings on slippery surfaces. There are several materials that can be used to cover a porch to prevent it from slipping. Let's look at the most common ones and find out their pros and cons.

1) Anti-slip self-adhesive tape. It is a polyester tape with a vinyl or abrasive coating. Attached with an adhesive coating on one side. Pros: simple, quick and reliable installation, good anti-slip performance, large selection of colors, low price. Cons: not durable (1.5 million passes, 3-5 years), requires a smooth surface.

2) Anti-slip self-adhesive strips (linings) and corners. They have a rubber base and are attached using an adhesive coating applied to the bottom of the material. Apply to slippery steps of stairs and porches. Pros: simple, quick and reliable installation, protect steps from chipping and abrasion, wide range of colors, low price. Cons: not significant protrusions at installation sites, requires a smooth surface.

3) Aluminum corners and profiles with rubber inserts. They have an aluminum base, which is attached to the base with dowels and screws, and have a removable rubber insert. When using such corners and profiles, slippery stairs will no longer be dangerous. Pros: reliable installation, durable, have easily replaceable, inexpensive rubber inserts. Cons: labor-intensive installation that requires care, minor protrusions at fastening points.

4) Anti-slip joint between tiles. It has a rubber base and is attached to the seams of tile coverings. Pros: reliable installation, aesthetic appearance, low price. Minuses: labor-intensive process installations, technological difficulties with repair and replacement of this material, cannot be repaired, protrusions on the surface of the coating.

5) Aluminum corners and tile trims with removable rubber inserts. They have an aluminum base into which an anti-slip rubber insert is inserted. They are attached between or under the tiles directly when laying them. A slippery porch will become quite safe when using these materials. Pros: reliable installation, easily replaceable rubber inserts, durable. Disadvantages: labor-intensive installation process, technological difficulties with repairing and replacing aluminum parts, minor protrusions on the surface at fastening points.

These types of anti-slip coatings can be mounted on concrete, metal, ceramic, marble, granite and even wooden porch. They are waterproof, heat-resistant and can be used both inside and outside buildings.

Rubber crumb coating will make the stairs safe and visually attractive.

Well, what should you do if none of the above listed anti-slip coatings suits you, due to full coverage surfaces of the steps. In this case, steps, slabs and crumb rubber coatings will help you. These materials consist of recycled rubber tire crumbs and a polyurethane binder. They are attached using polyurethane glue and can completely cover the entire step. Entry from the street using such a surface will be the safest of all available types of anti-slip surfaces. Pros: not reliable complex installation, covers the entire step and protects it from chips and damage, durability, evenness of the coating, wide choose colors, maintainability, safety. Cons: high price.

To buy the product you like, just call the numbers listed below or leave a request.

What to do to prevent the porch and steps from slipping in winter
What can be done to prevent the porch and stair steps from slipping in winter? What are the ways today that can effectively and quickly solve the problem of slippery steps and staircases? Especially in autumn and

Anti-slip coating on porch steps: many ways to make them safe

How slippery can the steps be? street porch after rain or snowfall, everyone knows firsthand. And some people even fell on them and received injuries. To protect yourself and your household or guests from such troubles, it is worth investing in anti-slip coating on the porch steps.

Materials capable of performing such protective function, there are several types. All of them will be described in this article, and all you have to do is choose the appropriate option.

Structurally, all types of such coatings can be divided into two types: the first in the form of narrow strips, strips and profiles and the second in the form of continuous coatings.

Tape overlays

There are quite a few varieties of narrow overlays. Let's try to navigate their diversity.

Types of overlays

They produce anti-slip coating on the porch in the form of narrow strips from materials such as rubber, rubber, PVC, and abrasive-coated tapes. They can be combined with anodized aluminum profile.

How to choose

When choosing one or another type of anti-slip pads, you should pay attention to the following parameters:

• Bandwidth. It can be from 15 to 100 mm, and in the case of an aluminum profile, even more.
• Her shape– flat or angular.
• Durability.

The shortest service life differs abrasive belts. Despite the fact that the fixation of hard particles is very strong, they wear out in 2-3 years.

• Additional functions. These include the possibility of replacing the anti-slip liner. There are also covers that glow in the dark thanks to built-in photocells.

• Installation method. If the porch has not yet been finished, you can consider embedded structures. In all other cases, in order not to spoil the steps, choose overhead or self-adhesive strips.
• Price and release form. Overlays can be sold in lengths different lengths or whole rolls, the footage of which is large for an ordinary porch of a private house.
• Appearance, color. Design entrance group is the calling card of your home, so even the shape and color of the strips glued to the steps should be in harmony with its exterior.

Perhaps the options shown below will help you with your choice

Rubber coverings

Anti-slip porch coverings made from crumb rubber are very popular. The raw materials for their production are waste materials crushed into crumbs. car tires and polyurethane glue.

Installation methods

Rubber coatings are produced both on a self-adhesive base and in aluminum profiles with mechanical fastening. There are also products that need to be glued to the base using polyurethane glue, or secured using flat or corner profiles or directly with dowels and screws.

Anti-slip porch mats and overlays are simply placed on the steps and held there by their own weight.

Let us describe, as an example, the technology for laying monolithic rubber steps.

Installation instructions:

• Preparing the foundation. The steps must be smooth, level, dry and clean. The tiles can be glued to a concrete, wooden, metal or polymer base.

To prevent moisture from accumulating on them, it is advisable to make a slope of 1-2 degrees towards the street.

• We prepare a primer from polyurethane glue with turpentine or acetone in equal proportions.
• Apply a continuous layer of glue to the steps using a roller or spatula.

• We cut the non-slip steps for the porch at the back, according to the depth of the tread. The scraps, if desired and of a suitable size, can be used for cladding the riser.

• We lay the step on the base, pressing it tightly to the surface.

You will be able to use the porch within 24 hours, provided the ambient temperature is above +10 degrees.

Gluing can be replaced with mechanical fasteners by screwing in self-tapping screws at a distance of 5 cm from the corners of the product, and making a step between them of no more than 50 cm. To increase the pressing surface, it is worth placing a washer under the screw head.

Advantages

Finished products can withstand mechanical loads and temperature changes and are very resistant to moisture.

• Having sufficient thickness, they perform not only anti-slip, but also shock-absorbing and sound-proofing functions.
• The anti-slip effect is provided by the properties of the rubber itself. In addition, a relief can be applied to the surface, which reduces the risk of falling on the slippery surface of the porch.
• Even in the event of an accidental fall, the likelihood of serious injury will be lower due to the shock-absorbing properties of the coating.

• When ice and snow freeze, the anti-slip coating for outdoor porches is easy to clean. You can impact it with hard, blunt objects without fear of destroying it. Whereas stone or ceramic tiles, as well as wood and concrete, do not withstand such a relationship.
• A thick layer of rubber muffles sounds. Perhaps this is not so important for street stairs, but the coating also has this property.
• Finally, the variety of colors is also a significant advantage. With the help of these materials, non-slip steps for the porch can be used to decorate the facade of the house, harmoniously blending them into the surrounding landscape.

The cost of rubber products is quite high, but since their service life is at least 10 years, such design of a street staircase fully pays for itself.

Conclusion

Anti-slip coating on porch steps: many ways to make them safe
Everyone knows firsthand how slippery the steps of a street porch can be after rain or snowfall. And some people had a chance to fall on them, getting

What to do if the steps on the porch are slippery?

If the steps on the porch are slippery, what should you do? This question is usually asked by property owners who are faced with the problem of slippery stairs finished with ceramic tiles, natural or artificial stone. Beautiful and practical in dry weather, such stairs become slippery when water and snow get on them. This phenomenon can lead to falls, which can lead to injury or death. In addition, the tiles in the pool are constantly wet and require great care when walking on it.

You can ensure that the surfaces of floors, stairs, curbs and showers are non-slip using several effective ways. They vary in type of execution, aesthetics and durability. Let's look at how different materials are processed to prevent people from slipping on them, whether they walk barefoot or with shoes, in rain or snow, or during organic and chemical spills.

Anti-slip stone treatment

Granite is the material that has all the qualities necessary for finishing floors and steps. A natural stone very beautiful and has incredible abrasion resistance. But a granite porch becomes very slippery at the slightest wetting with any liquid substance. Since winter in our country lasts from 3 months to six months, the steps must be safe during this entire time.

You can make natural stone on the porch non-slip in the following ways:

Options for stone anti-slip treatment.

1. Heat treatment. For this purpose it is used gas-burner, which creates a high temperature flame. When the stone is rapidly heated, the quartz crystals on the granite surface are destroyed. Its surface becomes matte and rough. Heat treatment of the stone is carried out in the house, since outdoors the pores in granite quickly become clogged with dirt and snow.
2. By grinding. Using special equipment, many grooves are applied to the surface of the stone. This makes it non-slip when wet. The entire surface of the step or several strips can be processed. But this option is only suitable for internal home stairs that do not come into contact with snow and an abundance of dirt that is carried on the soles of shoes.
3. Sawing. This method is the most practical, although the most expensive and time-consuming. Cuts are made in granite. They are made with a milling cutter or sandblasting machine. The resulting grooves are left empty or filled with rubber inserts. The inserts are made of a material that creates ideal grip on the sole.

Even very slippery granite steps can be turned into a comfortable and safe structure using modern technologies.

Anti-slip treatment for porcelain stoneware

Ceramic granite is becoming increasingly popular finishing material. Its appearance and performance characteristics are almost equal to those of natural stone. At the same time, the cost of porcelain tiles is much lower.

It is impossible to grind and burn porcelain stoneware, since it contains polymers that give the material viscosity. In addition, plasticizers are not resistant to high temperature. The coating can be made non-slip only with the help of special inserts. Cuts are made under them, which can be single or cover the entire surface of the steps.

Inserts are made from the following material:

1. Dense and wear-resistant rubber. It is resistant to abrasion, ultraviolet radiation and chemically active substances. If damage occurs to the inserts, they can be easily and quickly replaced without stopping movement.
2. Granite bars. The bars are matched to the color of the steps or in a contrasting design. The parts are connected using epoxy glue, which protects the joint from moisture.

In order not to waste time and effort on processing porcelain stoneware, you can purchase tiles that have anti-slip corrugations pre-made. Snow and water will be forced into the recesses of the tiles, preventing unwanted sliding.

Anti-slip treatment for ceramic tiles

Ceramic tiles do not have a uniform composition throughout the entire volume. Her external decorative layer cannot be damaged. Therefore, you can only combat slipping with the help of external pads.

The following products are used for this:

1. Aluminum corrugated strips. They are attached in the middle of the step using glue or self-tapping screws. Metal strips can withstand several seasons of intensive use. They are replaced as they wear out.
2. Rubber pads. They are mounted on the edge of the steps, which is the most dangerous place. In addition to the safety function, such overlays protect the edges of the tiles from inevitable chips.

You can worry about the problem of slipping in advance by purchasing corrugated tiles. This option will solve the problem of precipitation in the form of rain and light snow.

Universal anti-slip products

Thanks to modern technologies The problem of slippery floors and steps can be solved easily, effectively and beautifully.

Innovative solutions to this issue eliminate any dirty or noisy work.

Property owners can use the following means:

1. Anti-slip liquid. Getting on the surface of any material, it removes silicon molecules from it. They form microscopic sharp cones on a plane. Ideal adhesion to the sole is achieved without losing the quality of the appearance of the lining.
2. Anti-slip tape. It is a strip of PVC, one side of which is sticky and the other is corrugated. The product is inexpensive and easy to install. But this tape won't last long.
3. Anti-slip tapes. Very convenient devices having an abrasive or non-abrasive surface made of polymer plastic. Available in regular and fluorescent versions. Can stick to flat and curved surfaces.

You can use different types of devices on one staircase.

What to do if the steps on the porch are slippery?
If the steps on the porch are slippery, what should you do? This question is usually asked by property owners who are faced with the problem of slippery stairs finished with ceramic tiles, natural or artificial stone.

Porch decoration requires application special devices, with the help of which the safe operation of the entrance complex is ensured. One of important elements there are anti-slip pads on the steps. Their use is relevant in the arrangement of absolutely every building entrance system, regardless of the purpose of the structure, its size or status. Professionals recommend equipping the staircase with a system of anti-slip devices in advance, especially if the staircase cladding is made of smooth materials. Finishing the porch with an anti-slip coating for exterior steps helps prevent the risk of injury, especially in winter.

We study the features of the functionality

There are several types of facing products for these tasks. A certain part of the range of anti-slip coatings can be used as a means of protecting the surface of the stairs themselves. This is manifested in the ability of the material to absorb mechanical impact from the outside (shocks, physical exercise). Thus, the risk of chips and cracks on the surface of an expensive type of finish such as marble or porcelain stoneware is significantly reduced.

It should be noted that some of the presented samples also serve a decorative role. The functional characteristics of certain varieties allow them to be used as a floor-standing advertising and information medium, and some representatives of the latest generation anti-slip devices have a luminescent coating - they glow in the dark.

Important When choosing products for the final design of an external staircase system, it is necessary to take into account functional features each model. This contributes to a significant improvement in the quality of operation of the entrance area.

Structurally, anti-slip pads on steps are:

• Frost-resistant rubber strips for exterior stairs. This sample attracts potential consumers with its wear resistance, ease of installation and low cost. Modifications on a self-adhesive basis are easily installed on the surface of almost any material (stone or wooden steps, concrete, marble, etc.). A ribbed rubber tape is attached to the horizontal edge of the tread. There are also L-shaped configurations (corner).

• Rubber plate with notches on front side, intended for installation on street structures. Provides increased adhesion of the shoe sole to the surface and eliminates the moment of sliding, as it completely grips the tread and its corner part. Self-adhesive modifications and profiled versions are available ( aluminum profiles+ rubber layers) and others. Has shock-absorbing properties.

• Rubber insert tape in an anodized aluminum profile. The market offers corner (L-shaped) versions of this de-icing device and its flat (horizontal) counterparts. The design is relevant for the entrance staircase, which is operated in high intensity mode. Worn and deformed ribbed rubber liners are simply replaced, and aluminum parts last much longer.

• Inter-seam embedded anti-slip strip. H-shaped rubber pad is fixed between ceramic, wood or other tiles during the process final finishing external staircase.

What are the abrasive elements of the anti-slip system?

This category of products is mainly produced in the form of self-adhesive mats and tapes with a special coating of abrasive particles. Samples are also produced in rolls - any geometry can be cut based on the parameters of the finishing area. This type of staircase coverings is widely used in facilities with light loads. Mainly used on the exterior of private properties.

A special mixture with abrasives has proven itself well in the system of de-icing devices . The installation procedure begins with fixing the stickers on both sides of the treated area. This is important in order to:

• designate the area where an abrasive substance should be applied to prevent the risk of slipping;
• create a barrier to eliminate the effect of blurred edges.

The mixture is applied strictly to the designated area between the self-adhesive strips. After the solution with abrasives has completely dried, the stickers are removed and you can begin to use the area.

Aerobatics: rubber-coated steps

An external staircase with such cladding is an ideal safe zone during periods of adverse weather conditions. Rubber steps have the following qualities:

• provide optimal adhesion of the surface to the sole of the shoe;
• have high depreciation rates (even in case of an accidental fall, severe injuries are excluded);
• have excellent performance parameters;
• They also perform a decorative function.

Fixing the product on stairs made of wood, concrete, stone and other building materials is carried out using special adhesive substances or mechanically. To decorate the end of the tread, a corner rubber tape or its profiled analogue is used.

Advice! Some manufacturers of these products recommend using a combined fastening: the edges of the canvas are fixed with dowels and screws, and the middle with glue.

Multifunctional mats for the entrance complex

Traditionally, rugs are used as anti-slip and dirt-collecting decoration items. They are made from crumb rubber, rubber, modern polymers and other composites. Modifications are available: corrugated, with notches, spikes, removable and fixed. Innovative models of rugs for outdoor use have the following functionality:

• anti-slip and dirt-collecting element for the porch;

• advertising and information medium;

• part of the façade decoration.

Multifunctional anti-slip mats for the entrance area are relevant not only in the improvement of large shopping and entertainment centers or administrative buildings. Such tools are widely used in the private sector in combination with other exterior elements. They decorate both the staircase at the entrance to the house and the sidewalks from the gate to the porch, garden paths and steps. The difference between good and bad rubber coating

A progressive analogue of anti-slip pads - tape

Anti-slip self-adhesive tape is produced in various modifications. It is one of the popular porch accessories. The following varieties exist:

• luminescent tape (a special coating is applied that glows in the dark);

• vinyl (elastic copolymer structure with anti-slip properties);

• abrasive;

• tactile anti-slip tape.

Ksenia Skvortsova. Chief Editor. Author.
Planning and distribution of responsibilities in the content production team, working with texts.
Education: Kharkov State Academy of Culture, specialty “Culturologist.” Teacher of history and cultural theory." Experience in copywriting: From 2010 to the present. Editor: since 2016.

Comments 5

As a rule, the most beautiful and durable materials for the porch they also turn out to be the most slippery. The most dangerous weather for such coatings is changeable weather - when water freezes abruptly without having time to dry and evaporate. On such days, steps become a headache for every owner, because on a slippery porch it is very easy to fall and get injured. This situation applies not only to private households, but also to children's, municipal institutions, shops and entertainment centers.

Anti-slip coating is what is designed to save people from injury. Today there is huge selection porch materials that will make steps both safe and beautiful.

What qualities should anti-slip protection have?

First of all, the coating that prevents a person from falling must ensure good adhesion of the soles of shoes to the steps. But that's not all, there are a few more important points:

• since the porch is located outside the building, materials for outdoor use are required;
• the coating must work normally at different temperatures;
• be resistant to freezing;
• have a low moisture absorption coefficient, water should leave the steps freely and quickly;
• easy to install and serve for a long time;
• ensure injury safety.

Important! One of the main indicators is the strength of the coating and abrasion resistance. These factors are especially important for entrance groups with high traffic.

What provides the anti-slip effect

To achieve porch safety, several methods are used. Among them, the most common are:

1. Construction of a porch from anti-slip material.
2. Cover the existing base with non-slip tiles, mats or spray.
3. Rubber treads overlapping the steps.
4. Braking strips, linings, profiles, corners.

In each individual case, the most appropriate option is selected. This takes into account the cost of the coating, its characteristics, the purpose of the building and other factors. Most often, the owner of the house is interested in the aesthetic component, especially when the porch is built from expensive beautiful material(marble, granite, wood). Modern anti-slip materials fully meet this requirement - they do not interfere with the aesthetics and style of the building.

What to build an anti-slip porch from

During the construction phase, it is quite possible to build non-slip steps. To do this, you need to select a material with high coefficient friction and low moisture absorption. Natural roughness will ensure the adhesion of the soles, and quickly draining water will not turn into ice.

Such non-slip coatings include:

Such coatings are good for initial stage, when the porch is just being built. The tiles are easy to install on any surface (concrete, wood, metal) and last a long time.

How to make an existing porch non-slip

It often happens that a new porch, which pleased the owners in the summer, becomes very slippery with the arrival of cold weather. It would seem that the moment is lost - slippery porch and will remain so forever. But this is far from true. Now there are a lot of ways and options on how to turn even the most slippery steps into safe and practical ones.

The most common ways to transform a porch are:

• Spraying liquid mixtures based on rubber or stone chips. This method allows you to apply the mixture to the porch exactly in the place and in the quantity you need. In addition, it is easy to lay out various pictures or company logos from the plastic mass, which is suitable for trading companies.
• Roll materials are convenient where you need to cover a large area of ​​the porch. They are most often made of rubber; carpet coverings can also be found, but they can only be used inside a building. Anti-slip coating can be easily cut from a roll the desired shape and size. Mount it on the porch using profiles, fasteners or glue.
• Rubber pads or whole treads. The overlays are convenient to use seasonally - they are easy to dismantle during the warm season. The range of rubber overlays even allows you to decorate the exterior without in any way harming the design of the porch. Advertising is also often done on such rugs by applying logos and names. Rugs can be large and used as a pad in front of the door, in a vestibule or as the whole track(for example, in a swimming pool).
• Anti-slip strip - the simplest and most inexpensive way secure the porch. There are a great variety of them. These are aluminum, polyurethane, plastic profiles, which are mounted on the horizontal edge of the step. There are also a lot of self-adhesive tapes made from rubber or vinyl. You can use tape material to lay out any shapes and patterns on the porch, making the anti-slip coating also original. The most common are aluminum linings with rubber inserts. Such profiles are fastened with self-tapping screws, and the elastic band in them can be easily removed, which allows you to remove it in the summer or replace it with a new one. The cost of aluminum is quite high, but such profiles will last longer than others.
• Corner - most often made of rubber or aluminum and a rubber insert. Such corners can be used in conjunction with strips, complementing their effectiveness. Protection for corners performs two functions: firstly, it prevents the foot from sliding off the corner of the step, and secondly, it reduces the risk of injury to the porch, because sharp corners are the most dangerous area when falling on the porch.

Most often, several methods are used at once. Here a lot depends on the size of the entrance group and traffic. So, in private households it is better to use rubber tiles, removable treads or overlays. For big ones, multi-storey buildings It is more effective to use rubber mats in front of entrance doors and aluminum strips for steps.

In regions with long winters, it is more advisable to use continuous spraying of rubber coatings or porch cladding roll materials. This will eliminate the need to dismantle anti-slip coatings and make them easier to maintain.

Attention! In addition to the above, there are also inter-seam H-shaped profiles. They must be installed during cladding of the porch, mounted at the junction of adjacent tiles.

Conclusion

You need to think about the issue of porch safety at the design stage. In addition to comfortable, wide steps, you need ergonomic handrails and non-slip coating. Then the porch will become the calling card of the house, and not a place that will be feared and avoided in winter.

Clearing ice off porch steps often doesn't help because many brands of porcelain tile become slippery from even the smallest drops of water. What to do if it’s slippery on the street and how to solve the problem with budgetary funds?

To combat icing on stairs and improve home safety, many methods have been developed - ranging from special means, providing high-quality grip on the surface, and ending with linings, the fastening of which also reliably prevents slipping.

Ignoring slippery stairs and sidewalks can result in serious injuries, and if you are the owner of a hazardous property, you can be held liable.

Universal anti-slip products

Universal tools that provide reliable protection from slipping - the most easy option provide safety, which is suitable if the street is slippery, and which does not require any special work. The use of these means does not violate the integrity of the structure and the profile of the steps.

How to make steps not slippery, but reliable and safe, while maintaining their appearance:

• Synthetic fluids, the main principle of operation of which is to create a silicon layer from many microcones that provide the required roughness. The advantage of this method is its versatility, which allows the use of an anti-slip agent on almost any type of surface. The disadvantages include more high prices in relation to cheaper materials based on abrasive chips;
• A cheap and unpretentious option for covering already icy steps is ordinary coarse sand. Its main disadvantage is that it is carried by shoes and quickly pollutes the room. It also wears off quite quickly and is blown off the surface by the wind, and therefore requires constant updating of the coating;
• Salt is a popular and effective method of de-icing; however, in addition to dissolving the ice, it has an extremely negative effect on shoes, leaving hard-to-wash white stains on them, as well as destroying the outer coating, which reduces their service life;
• Another universal anti-slip agent for covering stairs using water, alcohol and any dishwashing detergent. By dissolving 100 grams of alcohol in two liters of water and adding a little degreaser (about ten drops), you will get effective tool to combat already formed ice. For practicality of use, it can be poured into bottles, from which you can then water the stairs as needed. The advantage of this solution is that the ice will not only become non-slip, but will completely disappear from the surface, saving you from the work of mechanically cleaning it.

Anti-slip treatment for ceramic tiles

Ceramic tiles or porcelain tiles are one of the most slippery materials used in porch steps. In addition, the peculiarity of the structure, which is the use of different brands of porcelain stoneware for the interior and exterior decorative parts, does not allow the use classical methods combat based on the interaction of chemical reagents or the abrasive properties of sand or other bulk material. Therefore, if it is slippery on the street and the porcelain stoneware is covered with a layer of ice, you need to use anti-slip mats or similar devices, the installation of which will completely eliminate the danger of slipping.

The most common and durable anti-slip material is corrugated metal strips that are mounted on the steps. In this case, you can take thin overlays located along the entire length of the steps, as well as special corners, which, in addition to the anti-slip effect, allow you to preserve the most vulnerable places of the tile - the sharp corners of the steps.

Another option for anti-slip porch equipment is to install flexible rubber pads. With their relative cheapness and ease of installation, anti-slip rubber tapes not only provide reliable adhesion of the sole to the surface, but also effectively prevent the destruction of the porcelain stoneware itself. In addition, the shock-absorbing properties of rubber make walking on steps more comfortable.

The durability and versatility of rubber pads, which are typically made from recycled rubber car tires, allows the use of such overlays all year round regardless weather conditions and temperature.

Tape overlays

One more effective option quick fix slippery spots on the porch is the use of anti-slip tape pads. The most optimal for outdoor use is an anti-slip mat on the steps made of high-strength abrasives, which have increased wear resistance that can withstand more than one month of intense load. At the same time, they are resistant to temperature changes and are easy to attach, and therefore can be used with any type of porch covering - concrete, ceramics, wood, etc.

To preserve porcelain stoneware and ensure safety, a metal profile is often attached to the steps. This profile provides more reliable grip and lasts longer than rubber products. But at the same time, a metal profile can ruin the appearance of the porch.

In the case where the porch is located indoors, you can use less rough anti-slip vinyl tapes, which, in addition to increased resistance to moisture, have improved tactile properties. You could say that this is perfect solution for use in swimming pools, baths and other wet areas.

The third type is luminescent strips, which not only make the porch safe, but also decorate it and additionally decorate the entrance to a restaurant, bar or other public establishment.

Rubber cover

Thanks to the huge demand for rubber anti-slip mats, which protect the material of steps from destruction, all sorts of design options are now available on the market. Non-slip rubber coating can be laid on stair treads and street paths, either as a continuous mat on the steps or as separate strips.

Among the main advantages of rolled rubber coatings:

• Installed on any porch shape;
• Easy to clean from dirt;
• Tolerates low temperatures well without loss of elasticity;
• Absorbs external load;
• Low price.

Installation rubber coating quite simple: it is installed like a puzzle, and rolled products they just roll out. Thanks to the use of recyclable materials and used tires in the production of this coating, the price of rubber coating is significantly lower than the price of metal analogues.

The disadvantages include the fact that in the case of covering with expensive marble or granite, almost the entire surface of the porch will be covered with rubber, which will affect appearance Houses.

Slippery steps on the porch are not only unpleasant, but also very dangerous. There are several ways to get rid of the problem.

The first method is anti-slip tape with a vinyl or abrasive coating. Applying self-adhesive film to steps is very simple.

It has good anti-slip properties, practically does not protrude on the surface, is inexpensive and is available in different colors. The big disadvantage of this material is its fragility. Already next season the coating will have to be renewed.

Method two - rubber anti-slip self-adhesive strips or corners. In addition to preventing slipping, they protect steps from abrasion and chipping. Like tape, the strips stick easily. They can also come in different colors. The disadvantage of such protection is that they protrude slightly above the surface.

You can also use special ready-made mats or cut the sheets yourself from rubber or rubber fabric. The mats are mounted with glue, and some mats have an aluminum base that must be secured to the steps with screws.

Another option is to use aluminum corners with anti-slip inserts made of rubber. These corners are secured with screws and dowels. The rubber part is removable, which allows you to change the strips for new ones without dismantling the base.

To completely cover the porch and steps, you can use crumb rubber sheet. It is attached with polyurethane glue and lasts a long time. The coating itself is also durable and wear-resistant.

If damage does occur, it can be patched. A wide range of colors allows you to choose the option that best suits the overall style of your home. There are also liquid, or rather paste-like analogues of this coating. They are applied to the surface, and after drying they form a dense rubber carpet.

Minus of coatings of this type lies in their high cost.

Return