at 05/06/2017 1,878 Views
A chair-cushion for such a swing can be easily sewn from an old bedspread, however, it will not be as durable as, for example, a wooden one, and besides, it is better to protect it from moisture
We go to the dacha to relax and work. We dream of lying in a hammock, drinking tea on fresh air, but this is not enough for the child. Its energy requires intelligent use, and it is in our power to create the right conditions for this. Simple and practical way– buy or build a swing with your own hands. So let's talk about what kinds of swings there are, what they are made of and how to build them.
- Material
- Building a wooden swing
- Let's build together
- two pillars
- rope (approximately 6 m)
- crossbar
- ring-shaped pendants (hooks are possible)
- fastener
- We carefully remove debris from the area under the swing and level the area.
- We dig two holes for the posts to a depth of 90-100 cm.
- Before installing the pillars in the holes, we will treat the lower part, approximately 50 cm, with tar. This way we will protect them from rotting.
- We attach the crossbar to the posts. It is desirable that the diameter of the crossbar matches the diameter of the pillars.
- We install metal parts using special fasteners. They can be purchased at the store.
- We use a grinder to process sharp corners.
- We attach ropes or chains to the crossbar, checking their reliability with our own weight.
- We tie the ends of the ropes to the seat, having previously drilled holes in it.
A seat woven from wicker with a back will provide children with comfortable stay on the swing
Children's outdoor swings: types
When choosing children's swings for an outdoor garden, parents are obliged to check them for absolute safety for the child. Let's consider what manufacturers offer us for our treasures.
To ensure the safety of the swing seat, it is necessary to provide a horizontal bar in front of the chair, which will provide protection for your child.
First of all, swings are divided according to the material they are made of. They can be wooden, metal and plastic.
Children's wooden swing for the garden They are environmentally friendly, durable, easy to assemble and beautiful in appearance. Impregnation of wood with a special composition increases the service life of products.
An old skateboard is also suitable as a seat for a swing, because its board is very strong and durable
You will have to tinker with such a wooden airplane swing, but the result is worth it, your child will feel like a real pilot
Metal swings are considered to be the most reliable and durable models. They can be forged, collapsible, welded. They weigh a lot, but this is justified by their strength and installation stability.
A hanging swing, the seat of which is made of metal rings, will become a real decoration of your yard
For a children's swing, you can use any option as a seat, for example, a part from a ski lift
Plastic designed for the little ones. Light and bright, they are perfect for children under 5 years of age, but they are afraid winter frosts and fade under the sun.
For children, a fabric seat with an enclosing structure around the perimeter will be comfortable and safe, where the child will feel confident
Swings are also distinguished by type of construction: hanging and frame.
Swing frame type in the form of a red wooden sofa - a bright accent for your area
Frame, of course, is preferable for children, since they have high stability, they can be freely moved to different corners of the site, they are durable and quite safe to use.
A simple swing can be made special - a little imagination and boring seats turned into colorful animals that will be much more interesting for your children to play with.
Hanging The models are simple and do not require special skills to assemble. To set them up, you need a supporting crossbar, a strong rope and a board for the seat. It is desirable that it has a back.
By choosing bright colors for the swing, you can further cheer up your children.
Car tires can be an excellent material for children's swings if you use a fun coloring for them.
Swing-chaise lounges designed for children under 3 years of age. They are usually low, with a soft back and a chaise lounge-style seat.
A chaise lounge with soft seats is a safe swing option for a small child
All these models can be purchased in stores, but if you decide not to spend money and build a children's swing for your dacha with your own hands, we will help you.
Material
There are two options for materials for structures with supports: metal and wood. Unfortunately, a children's metal swing for a summer house will require special skills from you. If you are not a blacksmith or a welder, building a metal frame will be problematic. And you will also have to look for pipes for supports.
To make such a swing you will need very little: wooden chair and chains - and unique decor ready for your yard
Children's swings are not particularly demanding in terms of design. For children, the main thing is movement, and a rope suspended from a thick tree branch with a board for sitting can provide it.
The optimal solution, which any parent can implement, is the construction wooden swing.
Building a wooden swing
The simplest design is a children's hanging swing for a summer house without a frame. It’s great if you have a large tree with a low, thick branch on or near your site. They threw two ropes over it, built a seat from improvised materials - and the swing was ready. As a seat, you can use tires traditionally loved by summer residents, a children's high chair, an abandoned skateboard, a piece of board, or an old ice cube. In general, everything that you think is suitable for a child to ride comfortably.
Most easy option organizing a swing - use a tree branch as a base
In such a round rocker on a soft pillow, tied to the base so that it does not “fly away”, it will be pleasant to spend time not only for children, but also for adults
To build a frame swing, we first decide on the location. It should be located close to the house, but away from the fence and trees. Then we will need lumber and tools. We choose coniferous species, but others are also possible, the main thing is that the tree is dry, durable, and without defects. We carry out pre-treatment of wooden parts: we clean, sand, and treat with a special compound to increase moisture resistance. For the swing we will need:
The beautiful and durable design of the swing chair will not leave indifferent not only children, but also adults
For frame stability, the side supports can be made in the shape of the letter “L”
Advice! Please note that nails are not suitable for fastening the swing parts; it is better to use bolts.
With your own hands you can build such a hanging swing-bed where your children will play
From the tools we take a shovel, a hammer, a drill, a tape measure, a plane, a grinder, paint and brushes. Well, the springboard for work is ready. Let's move on to step-by-step design.
To create such a wonderful swing you will only need an old chair, rope and bright paint.
U-shaped children's outdoor swing with green spaces vertical racks will provide shade and aesthetics for this simple design
We got the letter "P".
Advice!For children it is better to attach the seatbnot two ropes, but four. To do this, take two lengths for each rope, fold them in half, and thread the ends into the seat.
If you are confused by this option, you can build a more stable structure by taking four pillars for the frame and placing them in the form block letter"L". The sequence of work is almost the same, only you will need to dig four holes, cut the tops of the pillars at an angle, and connect them with metal parts. Between the pillars, at the bottom, at a height of about 50 cm, stiffening ribs should be nailed on both sides of the swing. This design creates opportunities for creating a real children's country corner. By increasing the distance between the posts, you can nail a long crossbar and add a rope or climbing ladder to the swing.
Children's wooden swings for the garden are environmentally friendly, durable and easy to assemble
A rocker-bed for rest and entertainment of a child, made of a wooden pallet
Let's build together
Now you know how to make a children's swing in the country from wood yourself.
An original bright children's swing, the seat of which is made of fabric with elastic bands
A funny swing in the shape of a deer will bring joy to every child
If the first experience does not disappoint you, do not stop there. The child is growing, or maybe you are planning the birth of a second baby, and one swing will not be enough. Build children's swings and slides at your dacha together with your neighbors or friends. Maybe among them there will be metal craftsmen, and then you will get an eternal swing for children of any age.
Multi-colored swing baskets will not only bring joy to children, but will also noticeably transform your yard
We will send the material to you by e-mail
How to assemble a children's garden swing
They try to do the weaving with a climbing rope. It has increased strength, so it will wear out for a long time. Let's start creating a swing.
- We divide the hoop into eight identical sectors. We make markings with a marker. This is necessary in order to correctly place the future rope web.
- Measure two diameters of the hoop and cut the required length of rope with a small margin.
- Let's start weaving the web. Remember that the rope should not be taut. The child should then fit comfortably into the seat and not fall out of it.
- All ropes, starting from the center, are intertwined crosswise. In the resulting central unit, multi-layer stitching is performed with nylon thread.
- In the same way, loops and knots are sewn, which are attached directly to the metal circle.
- The workpiece is wrapped with synthetic padding and sheathed with thick, moisture-resistant fabric. For convenience, a specially sewn pillow is placed on the woven web.
- Sew strong loops to the four edges of the circle. We attach carabiners to them and hook the swing on a strong rope to a crossbar or tree branch.
It is allowed not to sheathe the structure with fabric. You can simply wrap the hoop with a thick multi-colored rope.
PHOTO: the-furnish.otzovy.ru
On a note! One hoop in a ready-made swing can support up to 50 kg. If you need to hold more weight, you will have to take several hoops and twist them together using a rope.
Do-it-yourself outdoor children's swing for a summer residence: production features
If there are two or three children in the house, then you will have to create a multi-seat or at least a double design. Such swings are made quickly using the metal profile you are familiar with.
The available materials are: metal, fasteners and welding. It is also necessary to use the project that can be seen in the photo. Otherwise, there is a risk of making mistakes.
PHOTO: youtube.com
How to make a swing at the dacha with your own hands for two children
Let's start solving the question of how to make a children's swing with your own hands.
Illustration | Description of action |
---|---|
![]() | We cut the material to the required dimensions and weld the parts together. You should end up with two identical bases. |
![]() | Next, you need to weld them together so that finished frame got the shape of a triangle |
![]() | We take a metal tube and connect it to wooden block. Making a hole with a drill for a carbine |
![]() | We hang four chains on the carabiners, which will serve as holding elements. |
![]() | We cook the seat according to the planned pattern. Don’t forget to create rings through which the chains will be threaded |
![]() | All that remains is to paint and dry the structure. Option for children's entertainment is ready |
Try to make seats for swings from. It is treated with moisture-repellent agents and painted. This will ensure that the material does not delaminate over time.
DIY country swing for the whole family: popular options
To make a swing with your own hands in the country, metal is most often used.
Interesting do-it-yourself swing made from a profile pipe
To create a swing for a summer house with your own hands from metal, you need to provide the following components:
- quadrangular frame (it should become a load-bearing frame in the finished swing);
- A-shaped sidewall. It is made by welding several crossbars;
- one long tube. It will become the basis for attaching the swinging bench.
PHOTO: sadovyrai.ru
How to make a swing with your own hands from metal
The process of installing a swing for a garden with your own hands consists of the following steps.
- Using a grinder, we cut the material into separate fragments. To do this, you need to have a preliminary diagram according to which you can make blanks in accordance with the dimensions.
- We sand the boards using a special machine or manually using emery.
- We connect all the necessary parts together using special fasteners, bolts or welding seams.
- We dig 4 holes in the ground, install a metal swing for the cottage and fill it with concrete. Next we paint the structure.
PHOTO: krainamaystriv.com
As a result, you get an individual forged swing for the garden. For such a product it is necessary to have a preliminary diagram indicating all dimensions.
Sofa swing for a summer residence
Country sofa swings are in great demand. If it is not possible to buy them, then they try to make them themselves. Metal options are highly durable. And if it is also properly processed, it will not be afraid of moisture.
Tools and materials for manufacturing
For production you will need metal profiles, welding machine and seating material. Typically, wood is used for such purposes. In addition, you will also need material for the roof. Those who plan to use it should know that it is quite hot under it in sunny weather, and it is not practical during hail (the material begins to crack). It is ideal to take a tension awning.
How to make a garden swing with your own hands from metal: instructions with photos
Let's start following the instructions for assembling the garden swing.
Illustration | Description of action |
---|---|
![]() | We weld the frame. You can take your own sizes. It all depends on how much material you have. As a result, you should get a base like the one in the photo. |
![]() | We weld the frame for the swing to which the sofa will be attached. Next, we bend the arcs from the metal profile. They will play the role of armrests |
![]() | We hang the finished part on carabiners. Next we prepare the tree |
![]() | The finished version should look like this. The swing folds out into a sofa. The upper part of the frame is attached to the frame using strong chains. All metal parts must be primed and then painted |
To make the bed soft, it can be covered with a special fabric or periodically laid on top of a mattress and pillows for relaxation.
Dear readers, if you do not understand enough about the question of how to make a garden swing with your own hands, do not hesitate to ask questions and share your opinion. Our team will definitely contact you as soon as possible.
Save time: selected articles delivered to your inbox every week
What should children do in their free time outside? Run and play, build a house out of sand, ride a bike, kick a ball. And many children enjoy spending time on the swings. They love to rise and fall sharply. You can make such a swing with your own hands using available materials.
For several centuries, swings remained a popular attraction, not only for children, but also for adults. None folk festival V Ancient Rus' could not do without “flights” on these devices. During times Russian Empire they were among both the poor and rich people. Naturally, they looked different: the poor people swung on ordinary wooden boards tied with ropes to poles, and the swings of the rich were decorated decorative elements, pillows, bows and ruffles. Nowadays, interest in them does not fade; they can also be seen in courtyards, in many children's organizations, and in country “residences”.
What material is suitable for making a yard swing?
You can make a swing with your own hands, using almost everything that is at hand.
Table: advantages and disadvantages of different materials
Type of material | Advantages | Flaws |
Tree |
|
|
Metal |
|
|
Plastic |
|
|
Photo gallery: types of swings by material
Wooden swings require careful antiseptic treatment and surface sanding
Nobody disputes the strength and reliability of metal structures
Plastic children's structures can be purchased ready-made, but they are only suitable for babies
Use of non-standard materials
Some craftsmen can make swings from other materials, using car tires, plastic pipes, wooden pallets, etc. Even snowboards, skateboards and other non-standard materials, for example, an old basin, can be used.
Photo gallery: creative seats
Creating a hanging swing will not take much time
In skillful hands, even a snowboard can become a useful element of a children's swing
Older children like non-standard solutions, for example, swings made of tires
An old, roomy basin can serve as a seat.
Swing designs
By design features there are swings:
- frame;
- hanging;
- floor;
- transformers;
- electronic type.
Age preferences for frame-type swings are children from 3 to 10 years old. Such structures have big advantage- mobility. They can be placed in any area of a summer cottage or playground. They are strong enough to support the weight of primary school children.
Hanging swings are attached to a beam-crossbar. For this you can use chains, ropes, ropes. Their reliability increases when using a strong crossbar and subject to proper fastening.
Floor structures can be used by children under 5 years of age. Most often, when creating them, plastic and metal parts are combined.
For very young children, you can make a transforming rocking chair that combines several elements at once:
- Chair for babies;
- mini-chair;
- directly the swing.
It is impossible to imagine the modern world without electronics. There are swings equipped special system, which may include:
- timer;
- "music Center";
- a device for setting the rhythm of swing movements.
They are worth purchasing only if your family has a newborn child.
Photo gallery: different swing designs
Frame swing 0 familiar type of structure
The design of the floor swing allows for its transfer to any suitable place
Good and comfortable for children in a hanging swing with a backrest
Electronic swings are suitable even for little ones
What functions can a swing perform?
Swings, despite similar functions, may differ slightly from each other. This is due to both the design of these structures and their operating principles.
Which adult does not remember such attractions as boats? This type of swing can be used to entertain both children and their parents.
There are several types of children's structures, designated by one concept - swing-balancers. Such devices include swings:
- "scales";
- "pendulum";
- "yoke".
This fun activity is suitable even for small children. With the support of an adult, a one-year-old baby can also ride on the swing.
Nowadays, manufacturers of children's structures offer a wide variety of spring devices for swinging with balancing.
Of course, you can buy a swing in a store, but it’s better to work hard and build a swing yourself. Years will pass, but your child, already matured, will definitely remember the moments of “ups” and “downs” on the swing that you made with your own hands.
Photo gallery: spring structures for kids
“Across the seas, across the waves” - the motto of the design for children in the form of a boat
Sitting on a plane, you can feel like a real pilot
This ladybug won't take your child to heaven, but it will help you have fun
All the kids will love springing while sitting in a helicopter.
Preparatory work
If you decide to build a children's swing yourself, then you should do the preparatory work:
- decide on the type of future design;
- clarify parameters;
- draw a drawing;
- purchase necessary materials;
- get all the necessary tools.
Material selection
The simplest design of a swing is a suspended one. You can make them entirely wooden or combine different materials. For hanging elements, metal chains, ropes, strong cord, parachute lines or rope are most often used.
It is best to use a sanded board as a seat, since it is comfortable, will not crack in the cold, and will not cause discomfort to the child in hot or cold weather. You can use improvised means - old seats from chairs, armchairs, etc.
If you have more than one child or you often have guests with children, you can make a balancer for two. They make them from different materials. The advantages of metal swings are their strength, but for self-construction This design will require a good welder. Wooden swings are easier to make and less dangerous to use.
Calculation of materials
The easiest ways to make a hanging swing with a metal support and a wooden swing-balancer.
The materials you will need are:
- 2 iron pipes for support pillars(d=74 cm);
- 2 bearings;
- 1 metal pipe (for the crossbar) 50 cm long (d=150 mm);
- ready-made mortar for concreting;
- welding machine;
- 2 metal plates no narrower than 7 cm.
For the balance swing, prepare:
- any wooden material(average length - 2.5 meters). You can take an ordinary thin log, timber (40–50 mm thick) or a board about 25 cm wide.
- boards for seats (width - 30–40 cm, length - 45–60 cm) with a thickness of at least 30 mm.
- metal rod for support.
- hardware.
- paint or primer.
- 2 wooden handles(they can be made from a wooden rod with a diameter of 25 mm, about 60 cm long).
Outdoor swing schemes
You can make the work of making a swing easier by drawing up a design diagram. Drawings are made independently (under individual parameters) or taken ready-made from different sources.
Photo gallery: examples of drawings
The design of the swing must be very stable
Based on the diagram, you can build a frame swing from wood
The diagram must indicate the dimensions of each part.
Tool preparation
Depending on which design you prefer, you need to prepare:
- welding machine;
- drill;
- hammer;
- shovel or hand drill;
- screwdriver;
- grinder;
- hacksaw;
- roulette;
- plane.
Step-by-step instructions for making a hanging swing with a chain and a wooden seat
Having prepared everything you need, you can start working:
![](https://i2.wp.com/orchardo.ru/wp-content/uploads/2017/03/uglubleniya-dlya-opor-615x460.jpeg)
There is one more reliable way fastening the supports and crossbars - by welding a special structure (this option is very suitable for connecting wooden structural elements).
Bearings are mounted in the central part of the crossbar using metal plates. The bearings must ensure the movement of the swing in the forward/backward direction. The next steps are:
![](https://i0.wp.com/orchardo.ru/wp-content/uploads/2017/03/primenenie-podshipnikov-615x460.jpg)
The condition of the swing should be carefully monitored. It is necessary to regularly lubricate the bearings with machine oil and touch up shabby parts.
Before you invite the kids to ride, test the swing yourself.
Video: how to make a swing from a profile pipe at the dacha with your own hands
How to make a swing-balance for a child from wood with your own hands
Based on the drawings made and armed with the necessary materials and tools, you can begin assembling a swing-balancer made of wood. The work is carried out in 4 stages:
- installation of the base;
- production of rocker-balancer;
- assembly;
- painting the product.
The foundation is the basis for the reliability of the structure for children. This swing element can be constructed from wooden beam(10x15 cm), logs (20 cm), boards (no thinner than 3 cm), securing them in the intended location of the future swing. A lower frame about 1 m long is constructed from wood and vertical supports or racks at an angle are attached to it (using self-tapping screws).
The easiest way to make a rocker-balancer is from timber or a thick board.
For the entire length of the balancer (up to 2.5–3 m), 2 beams are laid parallel to each other, and shorter beams (up to 1 m) are placed between them (on both sides). The entire resulting structure is fixed with screws or waterproof glue (for carpentry). You can use one board.
At the edges of the rocker there are seats with handles, and in its central part there is a hole for a profile pipe.
The handles, like all other wooden parts, must be perfectly smooth so that the child does not drive a splinter into the skin.
The rocker arm and base are assembled using two pipes: a support pipe and a section mounted in the center of the swing. They are combined, a steel rod is inserted into drilled holes on both pipes.
Video: how to make a product from a tire
Decoration process
After the swing is installed, you need to take care of its appearance. It's easiest to paint them oil paint. This method is suitable for both wooden and metal structures. You can get creative and make the swing especially attractive for children.
Do not neglect the rules for using children's swings, which will help avoid injuries. It is forbidden:
- Getting too close to them while other children are using them.
- Rock while standing, resting your feet on the seat.
- Twist ropes, chains or other hanging elements.
- Get off the swing before it stops completely.
- Several children can sit on the same seat at once.
Before using the swing, you must carefully inspect all components and connections for their integrity and functionality. Lubricate the swing regularly to prevent rust and squeaking. Make sure that there are no sharp objects, protruding bolts, or unsanded wooden areas in the structure.
It is not difficult to make a swing with your own hands. The main thing is to adhere to the manufacturing technology of the product and the recommendations of specialists.
(18
ratings, average: 4,00
out of 5)
Kindergarten swing in the country is a casual game, great leisure time and fun. There is always a lot of children's laughter and joy around them. By installing them in your summer cottage, you can get another place to spend time pleasantly. Observing simple rules creating a design and safety, you can make a children's swing for your dacha with your own hands.
In order to do it right calculate capabilities and strengths, you must first determine the preferences of family members and get acquainted with manufacturing options (photos and drawings of swings for the garden can help with this). Some people prefer to lie languidly with a book or tablet, while others need to rock with their ears whistling.
Types of homemade swings
Wooden garden swing are divided into several main groups:
- balancing or sofa swing for the cottage. This type of swing is for two;
- hanging swings on chains, cables or ropes, like a bungee;
- swing made of logs, which are on stationary supports (classic look).
Each model can beat this way that the household will choose it as their favorite corner of the garden or dacha, and all the neighbors will begin to envy.
Where to install?
When to choose made in favor of bungee, then the answer to the question is obvious - we install it on the nearest tree, which in terms of strength inspires confidence. And when choosing a place for other types of swings for a summer residence, it is necessary to take into account the following factors:
- illumination The best thing, to Sun rays got to the site until evening. Thus, a garden swing made of wood will be protected from dampness;
- sufficient distance from fences, walls, wires, trees, sharp-pointed objects and thorny bushes;
- the site should not " blown by all the winds" Constant drafts are fraught with colds;
- It is advisable to immediately select a smooth surface topography so that there is no need to perform additional work.
It’s great when it’s under the structure soft grass or sand. This will make it possible to avoid injury from reinforcement or stone during a fall.
Gallery: DIY garden swing (25 photos)
Drawings of a swing for a summer house
You can do without them. However, when a serious project is meant with a claim to long-term operation, then, for reasons of saving building materials, it is advisable to prepare a drawing of a swing . Design a wooden swing It won’t be difficult to do it yourself if you have at least a little experience in such work.
General provisions that reflect the drawings of kindergarten wooden swings:
- sizes. That is, the base area and height;
- frame structure;
- type of suspensions and their length;
- number and type of seats;
- It is necessary to mark the locations of reinforcing elements and fastenings.
Material for production
Whatever type of swing is chosen, it is necessary focus a lot of attention on the quality of the material (directly on the wood) from which the structure will be constructed. Quality wood not only can ensure the durability of the structure, but also, most importantly, guarantees safe operation.
The following species performed well: larch, oak and cedar. Also, wooden swings are often made from birch, pine and spruce.
Wood you need to buy dry, without areas of rot or traces of mold. There should be no holes made by pests, crevices, or falling knots. Constructing a wooden swing with your own hands does not require a large volume, so you can check every beam and board.
Tools
Before you make a swing at your dacha with your own hands, you need to make sure you have all the tools required for this.
You will need:
This basic tools. When everything is prepared (project, drawings and materials), we begin to build a garden swing in the country with our own hands.
In this case, the main difficulty is what to hang it on. When you have a suitable tree growing, it is advisable to make the crossbar from a log (about 25 cm in diameter and 3 meters long), secured with ropes. A strong branch at the required height will eliminate need for this design. When not at the dacha a suitable tree is found, then, in addition to the load-bearing beam, you will also need two logs (30-40 mm in diameter) to assemble the U-shaped frame.
Pre-logs are needed treat with antiseptic and sand, then they are placed in prepared holes (50 cm) with crushed stone at the bottom and filled cement mortar. When pouring cement is not planned, the logs will need to be dug to a depth of at least a meter.
When installing the frame, the most important thing is to prevent distortion. There is an interesting option to adjust the level correctly: the Egyptian plumb line. D This system is quite simple: the top weight is a nut or any piece of iron curved shape, and the bottom one is a small container with sand.
As for sitting, there are many variations to suit every budget and taste:
- from a board (with or without a backrest, on two hangers or on one central one);
- from a log (one thick diameter or 2-3 thin ones, which are connected to each other with fastenings or rope);
- from a tire (solid or cut, horizontal or vertical arrangement).
To the choice of material for suspension, with which we will hang a bungee for fastening, it is necessary to treat it responsibly. Cables, ropes or ropes must be reliable, preferably new, and not rotten from attic supplies. Not recommended in in this case Use chains, as a child can easily get their fingers pinched in them.
Hangers during fastening on the supporting beam must be no closer than 1.5 m from each other. They can be secured using leather-wrapped loops or hooks. You can also use special steel fasteners - thimbles. The most durable fastener is a carabiner with a clamp. However, the carabiner must have safety teeth, otherwise it may move during strong swinging.
Usually , frame swing for a summer residence they have a fixed, solid base, for example, a sofa or bench. This is a more permanent structure, unlike rope structures. Most often, this structure is installed not only for children, but is also perfect for relaxing with the whole family. Construction options will depend from the selected material.
Log swing
Today, swings made from logs are quite relevant. Though they look bulky, but reliable and original. The seat can be hung on L-shaped, U-shaped and X- or A-shaped frames.
At the same time, X-shaped frames are the easiest to make: a load-bearing beam is placed on top of logs fixed in a “cross” (about 12-15 cm in diameter and 2.5-2.8 m long). The cross begins approximately 45-60 cm from the ends of the logs. For fixing, threaded spokes (15 mm) are best suited, which are secured with nuts on both sides after installation.
The lower ends of the supports are cut inward at an angle of 45 degrees. Afterwards, it is necessary to attach ties to each cross in the form of small thickness bars measuring 2-2.5 m at a level of 35-50 cm from the lower ends.
We install both crosses and fasten a third tension log between them at the same height as the first two, and also fasten it in the upper grooves load-bearing beam. The frame of the swing is made of logs. Now you just need to hang a sofa or put together a bench. The simplest seat can be easily built on a frame made of 6x8 cm timber, which is then covered with a 4 cm thick board. The parameters of the bench-sofa are as follows:
- back height 70 cm;
- bench depth 60 cm;
- length 180 cm.
Strong ropes, ropes, ropes, and chains can be used as suspensions. They are secured to the bench with carabiners or knots. But for attaching to cross beam two eye nuts and two large bolts will be needed.
Stages of installation of hangers:
- In the places where the hangers are fastened, two holes are made through from top to bottom in the supporting beam.
- The bolts are inserted here, and the eye nuts are screwed in at the bottom.
- Carabiners or ropes are inserted into the rings of the eye nuts.
Near a large bench, as a combined option, you can attach a single bungee for children to a long supporting beam.
This is a fairly convenient material for assembly, so building a wooden swing from timber in the garden with your own hands is not very difficult, however, skill will not hurt.
To assemble a swing from timber with your own hands, you will need the following material:
- for tightening the crosspieces one edged board 4x12x70 cm;
- for the crossbar one block 10x10 cm long 2.7 m;
- for side supports, four 12x12 cm bars, 3.2 m long;
- for the bench: approximately 15 linear meters of timber measuring 4.6x5.5 cm, for covering 20 linear meters of boards 2.5x4.5 cm, as well as fastenings and hangers.
First of all, we assemble the crosspieces. This is done in the same order as the principle for a wooden garden swing made of logs: mark, cut, connect, hang a chair or bench.
On a swing made of timber, the lathing of the crosses of their thin slats looks great, where you can attach flowerpots with flowers. Light roof would also be quite appropriate. A very interesting option is when the roof is made into a “house”, like over wells in the village. If you apply maximum imagination, this “haven” in the garden will become a favorite place for family vacation. Especially with soft cushions on the bench.
Wooden pallet
Probably many could see the lattice wooden coasters for various goods in warehouses and stores. Often, after the goods have been delivered, they remain on dacha areas. However, the idea of building a garden swing from it with your own hands can only come to a person with a remarkable imagination. The most important thing is that the pallet is not rotten and strong. It must immediately be treated with water-repellent and antimicrobial compounds, painted and dried.
So, here’s another idea on how to make a garden swing for your dacha with your own hands, and very quickly. A cable, rope, rope or chain is secured on 4 sides of the pallet and suspended on any frame or support. Thus, you can make a luxurious seat on which two children can comfortably sit and rock together on both sides. Or, by placing a pillow and mattress on it, we get practically a cradle.
When the household has two pallets, then by securing them with corners, you can build a bench that will look great on any frame base.
Balancer or swing scale
Once upon a time, such entertainment for two was a mandatory attribute on children's playgrounds. Not only children, but also romantic older people willingly rode them. This swing will certainly come in handy in a garden plot.
When with suspended structures everything is relatively clear, how to make a wooden balancing swing for your dacha with your own hands? This swing can be made from boards, bars and logs.
For the simplest classic version you will need:
- metal or wooden pin;
- a piece of thick saw cut or log;
- two handles;
- two beams measuring 30x30 cm;
- a board at least 4 cm thick and about 2.5 m long.
So, the construction process is quite simple:
- We lay the log on its side.
- We secure it on the sides with bars so that it doesn’t roll on the ground.
- Having found the center, screw the pin.
- We put a board with attached handles on the pin.
And now another garden wooden swing is ready.
How to care for a wooden swing?
- From the end to the beginning of the new season, you need to cover the structures with waterproof material.
- Annual painting or treatment special compounds will save the swing from pests and rotting.
- Do not create disproportionate loads.
- Avoid rust on metal parts.
A garden wooden swing is a great way to relax in the country. It’s even more pleasant if they are made with your own hands. Their construction does not occupy a large number of time, but you can enjoy the result literally every day!
How to make creative DIY swing: this will be discussed in this article on the website "" a drawings and photos will help you with this. Comfortable conditions for relaxing in the garden of a private house or on a summer cottage, you can achieve different ways. Along with and, not the last place is occupied by garden swing: photo interesting solutions can be easily found on the Internet, and using the instructions, you can easily cope with the manufacture DIY swing. Even adults can use this swing. The main thing is to accurately calculate the weight and build a reliable structure.
Swing located on a personal plot will become a source Have a good mood for both children and adults
DIY swing: photos of interesting ideas
Traditional materials for production DIY outdoor swing are metal and wood. In order to improve reliability and external characteristics you can combine these materials, and also partially decorate the metal structure with decorative forging.
Bright cocoon swing hanging from a tree branch
Helpful advice! To make the seat, you can use any available materials that may remain on the site after building a house or carrying out repair work.
For construction you can use:
- bars;
- plastic;
- strong rope;
- metal pipes;
- old armchairs or chairs from which the legs must first be removed.
Comfortable swing suitable for sleeping outdoors or reading
Car owners can use old car tires. They will go well with flower beds made from the same material.
Classification of garden swings
There are a large number of original and comfortable swing, capable of any summer cottage.
Conventionally, they can be divided into three large categories:
- mobile – products have a lightweight portable design, due to which swing can be moved around the site at any time comfortable spot, for example, in a house, on, in a gazebo or under a canopy during rain;
Mobile swing option with metal base
- family - products with a massive and weighty design. In their structure, they resemble those without legs with a large and high back. Due to its large dimensions, the whole family can fit on the seat. To exploit such swing was safe, they are securely fastened to a U-shaped frame. Strong cables or thick chains are used as clamps. If you arrange a roof or awning over the swing, you can use it even in the rain;
- children's - a special category of products, usually shaped like boats or hanging chairs. Structures are subject to special requirements regarding the frame, which must comply with all safety standards. Very young children can use swing only in the presence of adults and when using special belts. With their help, the baby is fixed in the seat and therefore cannot fall out.
With metal frame, painted in bright colors
Varieties and photos of swings in the country with your own hands
Swing can be classified according to other criteria. The following are distinguished: types of swings by type of construction:
- hammocks - suspended on a metal crossbar. A tree with a thick and straight lower branch can serve as a substitute for a crossbar. When using this design, a person gets the impression that he is floating above the ground. Similar swing are in great demand among those who enjoy reading books;
Hammock swing – great option for relaxation and admiring nature
Note! Hammock products, subject to manufacturing technology, can withstand a weight load of up to 200 kg.
- single – products with various types structures that do not require the installation of additional crossbars. These swing characterized by a quick installation system, and they can be installed anywhere. A variety of materials are used for manufacturing;
Beautiful hanging swing in the garden private house
- hanging - swing They are a seat suspended on several ropes or chains. Ropes are attached to the sides. Thanks to the application various materials, which make the product durable, comfortable and lightweight, hanging swings can have different shapes and sizes;
Cozy hanging fabric swing, created with your own hands
- sun loungers - products can accommodate a family consisting of two adults and one child. Swing They have a special design that involves fixation at a single attachment point, which allows them to be installed in the room. The material used for manufacturing is a special metal alloy. Despite the apparent airiness, these products are very durable.
Large family swing with metal frame
Before getting started, you should prepare the necessary materials and tools.
Make sure you have the following in advance:
- file or sandpaper(for working with a metal surface);
- welding machine;
- electrodes;
- containers for mixing the solution;
Metal swing are distinguished by their elegance and apparent lightness of design
- ingredients for preparing the solution (crushed stone, water, cement, sand);
- fasteners (nuts, bolts);
- metal pipes;
- wrenches and shovels;
- grinders and a set of metal discs.
Modern design metal swing for garden
Making a swing with your own hands: drawings and photos
The first thing to do is prepare the pipes. Cutting the material is carried out as follows:
- side stand – 2 pcs., length – 2 m;
- base element - 2 pcs. on each side, length at your discretion;
- crossbar – 1 pc., length – 1.5-2 m.
Mounting dimensions metal swing and wood
Helpful advice! After cutting metal pipes, burrs may form on them. To remove them, use a file or sandpaper.
Elements intended for the base should be secured by welding at an angle of 45°. Next, the crossbar is welded to the posts at an angle of 90°.
To install the structure, two trenches must be dug. The width of these recesses should correspond to the resulting tripod, and the depth should be at least 0.8 m. The width of the crossbar should fit between the trenches.
Hanging swing unusual shape with metal frame
The support parts of the swing will be installed in the recesses. First, a sand cushion should be formed at the bottom. The thickness of the layer is 0.1-0.2 m. After this, the embankment is carefully compacted. The base of the structure is installed on top, the recesses are filled concrete mortar.
To prepare the mixture, mix sand, cement and crushed stone in following proportions: 2:1:1 (respectively). Add liquid to the resulting mixture and mix the solution. As a result, you should get a homogeneous mass. Make sure it is not too liquid.
Drawing of a garden swing: 1 - screws for fastening the back and seat slats; 2 - strips; 3 - corners of the rocking seat frame; 4 - swing truss base rod; 5 - rivets; 6 - connecting strip of seat rigidity and seat suspension; 7 - side rods of the swing truss; 8 - connection of the ends of the awning support frame; 9 - cord for hanging the rocking seat; 10 - carbine; 11 - ring; 12 - scarf-strut; 13 - upper rod of the swing truss; 14 - connecting bolts with washers and nuts; 15 - liner retaining bolt; 16 - liner with a hole and internal thread for a connecting bolt; 17 - wide spacer washer; 18 - support frame for the awning; 19 - washer; 20 - bolt connecting the top rod to the side rods; 21 - crossbar - 2 pcs. (steel strip with bolts)
It takes about a week for the concrete to harden. Until this point, it is not recommended to attach a seat to the crossbar, which can be held in place by cables or metal beams. After making sure that the solution has hardened, attach the hooks by welding and install the seat on the cables. If used metal beams, weld the seat to them. When the structure is completely ready and installed, it can be coated with paint to make the swing beautiful appearance and protect the metal from corrosion.
Metal swing for the garden with awning and soft pillows
How to make a swing in the garden with your own hands from wood
This technology is being considered that can simultaneously accommodate several babies at once. The size parameters of the swing can be changed at your discretion.
Helpful advice! Use the following types of wood as a material: birch, pine, spruce.
Children's outdoor swing built from wood
Preparatory stage: tools and materials
The list of materials needed to create a wood structure includes:
- board – 15 pcs., length – 2.5 m, section – 2.5x10 cm;
- board – 1 pc., length – 2 m, section – 5x15 cm;
- carabiner – 6 pcs.;
- self-tapping screws – 250 pcs., size – 3.5x52 mm;
- welded chain, the length of which is selected taking into account the height of the swing, the thickness of the links is 0.5 cm;
- galvanized screws – 2 pcs. size 1.2x10 cm + 2 pcs. size 1.2x8 cm.
DIY baby swing drawing: 1 - side outer part of the seat frame – 2 pcs. (90x35x375); 2 - side inner part of the seat frame – 2 pcs. (70x35x375); 3 - seat frame cross member – 2 pcs. (90x35x375); 4 - vertical part of the armrest – 2 pcs. (45x35x275); 5 - vertical back part – 2 pcs. (90x35x650); 6 - horizontal part of the armrest – 4 pcs. (45x35x530); 7 - upper part of the armrest – 2 pcs. (145x20x585); 8 - upper chain holder – 2 pcs. (45x35x300); 9 - lower chain holder – 2 pcs. (70x35x150); 10 - front and rear parts of the seat frame – 2 pcs. (90x35x1300); 11 - back cross member – 1 pc. (90x35x1400); 12 - seat board – 1 pc. (90x20x1170); 13 - seat board – 3 pcs. (90x20x1230); 14 - back board – 12 pcs. (90x20x850)
The market assortment offers self-tapping screws of various colors. The shade of fasteners can be effectively played up in swing design, so you should pay attention to the color of the screws. By choosing fasteners to match the wood, you can hide the joints of the structural parts. Self-tapping screws of contrasting colors will allow you to achieve an interesting effect.
Hanging wooden swing painted white
Don't forget to prepare the tool:
- roulette;
- pencil;
- a square to measure the size of the corners;
- saw circular type for cutting wood;
- drill and a set of drills for it;
- plane and hacksaw;
- hammer.
Scheme drawing wooden swing devices with dimensions
Technology for creating children's swings: how to make a structure with your own hands
If you take on making a swing with your own hands, you can make your work easier with one in a simple way– make a plan and try to stick to it. It is recommended to prepare a project in advance, draw up blueprints and mark on them all the dimensional parameters, fastener locations, and analyze the future product for reliability.
If you have no experience in composing drawings, use ready-made projects. , which you can find on the Internet, will help you decide on the choice of a suitable design. Don't forget, there is a big difference between swings designed for adults and children's versions of products.
Suspension swing option from a used car tire
On pre-prepared parts (each 1.5 m long), the cut should be made strictly at a right angle. Boards 2 cm thick are intended for seat construction. It is better to use boards with a thickness of 1.2-1.3 cm to make the backrest. For the seat you will need 32 planks, 15 of which should have a length of 0.45 m, the remaining 17 - 0.5 m.
Helpful advice! To prevent cracking of wood during installation of self-tapping screws, drill small holes in the structural elements that are to be fastened.
Assembly swing sizes with metal frame
Working with the back and seat of the swing
If you want to make a more comfortable and convenient design for the seat back, it should be given a shaped shape. To achieve the desired result, use a board with a large thickness (section - 5x15 cm). You need to make 6 parts. Using a marker or pencil, apply the appropriate markings to the workpieces.
After this, you need to determine the angle at which the back will be fixed. The slats are fixed in equal increments. Make sure the slats are installed level. To do this, first perform fixation on the sides, and then in the middle.
Baby swing, suspended from the frame on chains
Increase operating comfort swing installation of armrests will allow. It is recommended to use timber for these purposes. The width does not have special significance and is selected taking into account your own wishes. The armrests are screwed to the frame part of the backrest on one side, and attached to the seat on the other.
On next stage You can attach a welded chain to the frame. The optimal place is the lower area of the armrest, that is, where it connects to the seat. Take a special connector that has a ring on one side and a thread on the other. It is attached to the crossbar and the frame of the seat. Subsequently, a chain will pass through these rings.
Drawing of a chair with a back and sides for a swing(cm): 1 - horizontal sidewall element - 4 pcs. (5x5x70); 2 - connecting rod - 3 pcs. (d = 2.5 cm, length 80 cm); 3 - reinforcing angle - 4 pcs. (2.5x10x10); 4, 11 - vertical sidewall elements - 4 pcs. (5x5x37.5); 5 - back frame element - 2 pcs. (5x5x37.5); 6 - back and seat grille element - 13 pcs. (d = 2.5 cm, length 58 cm); 7 - seat frame element - 2 pcs. (5x5x67.5); 8 - suspension cord guide - 2 pcs. (d = 2.5 cm, length 10 cm); 9 - pin - 4 pcs. (d = 1 cm, length 7 cm); 10 - seat clamp (d = 2.5 cm, length 68 cm)
To secure swing It is better to use an A-shaped rack. You need to take strong logs as supporting elements. Anyone who knows how to use a welding machine can take on the production of a metal frame.
Bright children's swing with original design
Building a support part for a swing with your own hands
Many masters involved in making swings For summer cottages, prefer A-shaped racks, as they provide high level reliable, durable and can withstand heavy loads. At this stage you will need the same set of tools as when working with the seat. Of course, if we are talking about a stand made of wood. Otherwise you will need a welding machine.
A-frame support posts are reliable, durable and can withstand heavy loads
The first thing you have to do is make the racks. They must be the same and have the same size. Subsequently, you can install them at the distance that you need. This figure depends on the width of the seat. A crossbar should be used to connect the supports.
Important! Follow accurate calculations the angle at which vertically located elements of the racks will be connected. The upper part of the pillars needs to be securely fastened. Otherwise they may be led away.
Reliable fastening of the upper part of the pillars will ensure a high level of strength of the entire structure
To mount the crossbar, mark 1/3 of the support posts. It is at this level that the installation will take place. Self-tapping screws and corners made of metal can be used as fixing elements. Make sure that the crossbar is installed at the same height. Typically, swings have one crossbar, but if you want to increase the strength of the structure, you can install two.
To install the base, dig holes in the ground. The maximum depth is 0.8 m. The structure is installed on a cushion of crushed stone with a thickness of about 0.2 m. After the racks have been placed inside, they are filled with concrete mortar.
Children's swings hanging type with wooden frame
Taking into account the fact that wood is extremely susceptible to rotting, the lower part of the racks should be treated with an antiseptic and insulated before concreting the base. For these purposes it is worth stocking up waterproofing material. Roofing felt will do.
Since the structure will be used by children in the future, it needs to be secured. Sharp corner parts should be rounded; irregularities and burrs are removed by grinding.
Process construction of children's swings made of wood
Photos of do-it-yourself swings and features of their manufacture
Even if you are not at all comfortable with a plane and a welding machine, this does not mean that a swing in your summer cottage will remain a luxury for you. There are a lot of simple designs that you can handle making. Moreover, most of them do not require the purchase of any expensive materials. You can always arm yourself with improvised means.
Simple children's swing for the garden suspended on ropes from a tree branch
Swings made from scrap materials: pallets
Pallets are very popular look material from which furniture for home and garden is made. Due to their versatility, they can also be used for organization of swings on suburban area. To do this, you should have on hand one pallet, a rope and a tree where the structure will be suspended.
Helpful advice! As a substitute for wood, you can install strong support poles.
Pallets are an excellent material for creating original garden furniture
Even a product created on the basis of one pallet can have several modifications. The one-piece element can be fixed in a suspended state at the four corners using ropes. This is enough for the swing to perform its function. To create coziness, just place a small mattress on top of the pallet and cover it with a blanket or sheet. Several pillows on top will be a unique solution to the problem of the lack of a backrest.
Cozy children's swing made of pallets with a soft mattress and pillows
Constructions of this type can be used not only for reading books on outdoors, but also for basic relaxation from the midday heat in the shade. They can even be used for sleeping.
For creating a swing with your own hands with a full back you will need two pallets. As is the case with wooden structures from boards and timber, here you should also treat the surface with sandpaper to get rid of burrs. The product must be thoroughly cleaned and painted using a dye intended for wood and street conditions operation. It is enough to use a moisture-resistant varnish that will not spoil the beauty of the wood.
Hanging swing for a summer house made from pallets
Other types of DIY swings
The most simple option A swing is considered to be a board-shaped seat suspended with ropes. To prevent rapid fraying of the rope, two more pieces can be nailed to the sides of the board. After this, 4 holes are made through which the ropes are threaded. To secure it, strong and tight knots are tied at the ends. The structure itself can be mounted either on a tree or on a U-shaped support base.
Beautiful hanging swing will decorate your garden plot
Swing, suspended on ropes, can be made in another way. Instead of holes, grooves are formed in the board: a pair in the end part and a pair along the edges in the corner area. The seat (board) can be shaped into a semicircle or left straight. Due to the tension force, the rope will not jump out of the grooves, despite the fact that they are open.
Safe children's swing you can create it yourself from textiles and wood
Helpful advice! If you have an unusable skateboard or snowboard, you can use it instead of a seat, giving the swing an original appearance.
For making a swing with your own hands You can use a large number of different materials on the site, up to car tires. It is enough to hang the tire on a tree branch using a rope. If you care about nature, you should not use a chain - it injures the bark too much.
Hanging wicker chair swing decorated with bright ribbons
Some craftsmen give tire swings intricate carved shapes. For getting original design it's enough to have a sharp one cutting tool and ready-made diagrams. Tires can be cut using a construction knife. Pre-mark the surface for cuts using chalk or a dark marker. Ready product can be painted in bright color or cover with drawings.
Swing made of two logs Not big size, tied together with a rope, are very popular among summer residents. The main thing is that the wood is cleaned, leveled and tightly bound.
Drawing for creating a swing in the shape of a horse from an old tire
Beautiful designs and methods of their fastening
There are several options for mounting systems that can be used for swings. These options are the most common:
- carabiners - in this case, the beam is wrapped around an element that has round section(used for rounded beams) or rectangular ( square shape carabiner for beams);
- anchors - in fact, they are the same carbines that have a through type of fastening.
Reliability and safety of the design are the main ones properties of a good children's swing
Swing with four attachment points(2 on the seat and 2 on the back) can be hung in two ways. In the first case, you bring chains or ropes together into a common ring, which is a connecting carabiner. After which one of the ropes or chains is attached to the crossbar with the main carabiner. As a result, you get two fixation points on the crossbar.
Another option involves installing a fastening system, which is based on the use of 4 carabiners that secure each of the ropes or chains leading from the structure.
Device options swing seats, as well as the method of attaching anchors to the crossbar
Bench-shaped swings can be mounted on hooks that are mounted in the side walls of the support posts.
Materials for creating beautiful swings for children in the country with your own hands
If you do not want to limit yourself to using scrap materials, but want to create an original and beautiful design, you can use interesting types of wood and metals.
Helpful advice! Improve the product by adding a comfortable backrest or a crossbar located in front to its design. Thanks to this limiter, you can increase the level of operational safety of the swing.
For outdoor hanging swing it is better to choose boards from hardwood trees
For creating beautiful swing you will need:
- carabiners made of durable metal;
- boards from deciduous trees;
- hanging chain;
- self-tapping screws with different dimensional parameters;
- screws equipped with rings, which are also used for hanging home children's swings installed in the room.
Comfortable baby swing hammock type made of thick colored fabric
The set of tools for work is limited to:
- drill and set of drills;
- saw and hacksaw;
- jigsaw and plane;
- hammer;
- devices for measuring and marking (square, tape measure, chalk, pencil/marker).
Ordinary old tires can be turned into original swings for children
For swing installation need to be selected shady place, for example, an area under a tree or under the roof of a canopy or terrace. You can even equip the structure itself with a roof or canopy, otherwise you will have to cover the product with a tarpaulin or film in bad weather.
Initial stage of product manufacturing
Any stable swing design begins with digging support pillars to a depth of 0.8 m. The remaining space in the recess is filled with concrete mortar. The crossbar is then connected to the posts.
Construction of a wooden swing: 1 - top tie (length 115 cm, width and thickness of the board 10x5 cm); 2 - board-visor, covering the heads of the bolts and protecting the screed from bad weather (length 145 cm, width and thickness 22.5x5 cm); 3 - two racks (height 275 cm, width and thickness 22.5x5 cm), the distance between the racks is 105 cm, the ends of the racks are concreted into the ground to a depth of 60 cm; 4 - galvanized chain attached at the top and bottom to the eye bolts on the turnbuckles; 5 - seat (length 60 cm, width and thickness 15x5 cm)
Further actions depend on what type of material is used to make the product. If swing are created on the basis of metal pipes, the connection of all elements is carried out only using a welding machine. Wood supports will require pre-treatment with an antiseptic and nuts and bolts as fasteners.
The seat is created from two frames. One of them will be the back, the second will be the seat. Install and secure pieces of plywood or wood on them. After this, you will need to secure the frames at an angle of strictly 120°.
Process construction of a children's complex with swings made of wood
In order to attach a rope or chain to the seat, brackets or special hooks are installed. This will allow you to hang the structure from the crossbar.
Note! The swing is suspended in such a way that the feet of the person sitting on it can touch the ground.
The design of the structure can be improved by decorating it or installing some unusual object as a seat.
Baby swing hanging from a tree on a rope
Do-it-yourself installation of the fastening mechanism on a swing
Hanging the swing seat to the crossbar is carried out using staples or special hooks. If the structure will be held in place by cables, you will also need to purchase clamps that will serve as clamps. It is also possible to use other materials, such as chain or rope.
It is recommended to use a chain with large links. This will increase the service life of the product due to the fact that the metal from which they are made is not afraid negative impact weather conditions and temperature changes. Moreover, the chain is often used to decorate the landscape. It will complement the design of the yard in a suburban area.
Installation of fasteners for hanging swings
The suspension installation area requires careful strengthening. For decorative purposes, you can put pillows, a mattress on a wooden seat, or pull an awning over it. These elements will not only be able to decorate the product, but will also increase the comfort of use and make it a pleasant place to relax.
Since the design is made for children, it is better to equip the swing seat with a comfortable backrest. As for the suspension, it is less important in this case.
Scheme drawing devices for hanging swings from a car tire on metal frame: 1 - racks; 2 - tire; 3 - welded calibrated chain; 4 - M12 bolt with eye; 5 - section of channel No. 14, the length of which is 200 mm; 6 - steel plate 140x200 mm; 7 - M12 bolt
How to make your own swing safe
The area where children relax and have fun must be safe. By following simple rules, this can be easily achieved:
- use the safest and most reliable nodes;
- nylon rope is less harmful to the tree than others;
- the best wood option is oak;
Children's swing made of wood, created with your own hands, in the form of a mouse and a beetle
- Having figured out how to make a swing in the country, before fixing it to the tree, carefully inspect the branch on which it will be suspended. Make sure there are no cracks, excessive dryness, or signs of disease;
- If you use a chain to hang the swing, it is recommended to place it inside the plastic tubes. Otherwise, the child's fingers may get caught in the links;
- The branch with the swing should be checked for reliability, since during the use of the structure the wood gradually grinds and collapses. This needs to be done every week;
Before use swing children, be sure to check the design for strength
- Before allowing children to use the product, check its durability. The largest family member is suitable for this. If the swing can support his weight, then it can be put into operation;
- use only reliable carabiner options.
We should not forget about the aesthetic side of the issue. Make the sides of the swing shaped to make it interesting for children. The sides can be made in the shape of dinosaurs or cars, ships.