Installation of toilet installation. How to install a wall-hung toilet - installation technology What is needed to install a wall-hung toilet

Suspension systems are becoming increasingly popular. This is not surprising, since wall hung toilet takes less space, compared with floor systems. In addition, they simplify the cleaning process, since there are no hard to reach places. Considering that a wall-hung toilet looks much more aesthetically pleasing, such a high interest in wall-hung systems becomes understandable. But the process of installing a wall-hung toilet often raises questions, so it is necessary to consider this process.

Preparatory work.
Installation installation
Toilet installation.

Each stage does not cause any difficulties for a person who has experience working with the tool.

Preparatory work

First you need to determine the place where the toilet will stand. If redevelopment is not planned. If only the equipment is replaced, it is natural that the location will not change. Otherwise, everything depends on the future interior of the room. It is important to know which wall is located behind the future location of the toilet. This is due to the fact that it is attached only to main wall. Plasterboard partition will not work, as it simply will not withstand the weight of the system and will break.

When a location has been determined, it is necessary to supply cold water and a sewer outlet to it for waste disposal. This must be done before installing the installation system, since after it the work will be difficult.

When the location is determined and prepared, you can proceed to install the installation.

Installation of an installation system under a wall-hung toilet

In order to install the installation correctly, it is important to carefully approach the marking process. This stage is very important, since an incorrectly marked system will not fit correctly and, as a result, everything will have to be redone.

Therefore, before installation, you need to carefully measure everything and determine the height of the future toilet. Experts recommend that it does not exceed one meter, but if the family is tall, this number can be increased. When the location and height are determined, markings are applied for fastenings and holes are drilled. It is preferable to use special anchor bolts rather than ordinary dowels, since the load will be static and constant and quite large. Dowels will not be able to provide sufficient reliability of fastening, so distortions of the system are possible in the future.

Special attention should be paid to the reliability of fastening and immobility of the structure, since the system will function long years and must be well secured. If desired, it can be further strengthened to achieve complete immobility.

When the installation system is installed, it must be vertically aligned in the front plane, the top plane must be horizontal, and the supporting frame itself must be securely fastened and motionless. This is the only way to ensure good view and normal operation of the system in the future.

Bowl installation

After all the installation work has been completed, the niche is sealed with plasterboard. It is advisable to use moisture-resistant material so that it does not swell from moisture. At the same time, we must not forget about the need for access to the drain tank, so it is necessary to provide a hatch in the finishing.

After finishing is completed, the toilet bowl is installed. This stage of work is carried out in accordance with the manufacturer’s instructions, since different models may require different actions. But the differences are not significant; the actions differ only in small details.

If preliminary calculations and measurements were made correctly, then the height of the bowl will be about 40 centimeters from the floor. This value is considered optimal and most convenient for ordinary people.

If you follow the instructions and carry out the work carefully and carefully, the process of installing a wall-hung toilet will not cause any difficulties. As could be seen, complex work no, so almost anyone can install a toilet with their own hands.

Video How to install a wall-hung toilet

Setting up a GROHE installation

An excellent decoration and an extraordinary detail in the design of a bathroom would be the purchase of a wall-hung toilet. This device does not take up much space, and when the right approach to installation, will last quite a long time. We’ll talk about how to choose a wall-hung toilet and how to install this device.

Construction and design of a wall-hung toilet

A wall-hung toilet is a structure consisting of a bowl and a cistern, which are placed in a suspended state.

The bowl is a vessel made of porcelain. The only difference between a wall-hung toilet and a floor-mounted one is the type of fastening, which is done from the side.

Wall-hung toilets are different standard equipment. Wall-hung toilet dimensions:

length: 50-60 cm;
width: 30-40 cm;
height 35-45 cm.

The system of wall-hung toilets is characterized by the presence hidden system drain, which consists of a cistern. It is located behind the partition and has the following features:

small sizes, thickness 80-120 mm;
the start button is located on the side;
It has plastic base, equipped with thermal insulation, which prevents the formation of condensation.

The standard tank volume is 8-10 liters. to install cistern It is necessary to have pipes, components, a side drain button and a flush panel.

Some toilets require the installation of a flush, which is carried out thanks to the presence of high pressure into streams of water. This system consists of a special button that is connected to the water supply system.

Wall-hung toilet photo:

Advantages of installing a wall-hung toilet

1. A wall-hung toilet allows you to save space in the bathroom, as it has a built-in tank and does not require a large distance from the wall for installation.

2. The high strength of the toilet will not allow the bowl to break even when suspended.

3. Due to the fact that the toilet is suspended, the floor under the toilet is easy to clean.

4. A variety of types will allow you to choose a toilet in relation to material and individual preferences.

5. Reviews about the wall-hung toilet characterize this device as a convenient, reliable and durable item.

6. Wall-hung toilets fully comply with sanitary and hygienic standards.

Types of wall-hung toilets

Depending on the size, wall-hung toilets are divided into:

small, the length of which does not exceed 550 mm, are installed in small bathrooms, significantly saving space;
medium, up to 600 mm long, are the most popular, as they are excellent for installation in any room;
large ones, up to 700 mm, are installed if there are elderly or disabled people in the house.

In relation to the design, toilets are distinguished:

wall type - the frame is fastened to the wall and to the floor;
corner type - attached at a certain angle only to the wall, significantly saving space.

Depending on the shape, toilets are distinguished:

round,
rectangular,
square,
oval.

Mounting a wall-hung toilet

There are two ways to attach a wall-hung toilet:

using a ready-made installation system,
concrete screed.

The first option is more expensive, but less complex. The finished installation system consists of a steel frame that is attached to the wall and to the floor. To fix the frame, four points are used: two are located on the wall, and two are on the floor.

More expensive systems offer a choice of the width of the dots and their adjustment.

This installation is installed at a distance of 15-18 cm from the wall. The set includes:

toilet bowls,
tank drain,
flush button panels,
open ceramic cistern,
installation systems.

Installation of a wall-hung toilet without a finished installation

To install the toilet yourself, without using ready-made fasteners, you must have:

two threaded rods, the diameter of which is 2 cm and the length is 50-80 cm;
four nuts, four washers;
40 liters of concrete mass grade M 200;
several sheets of plywood;
wood screws.

To connect a wall-hung toilet you need:

drain rectangular coupling;
plastic sewer pipe with a diameter of 1.10 cm;
silicone sealant.

Instructions for implementation preparatory work before installing a wall-hung toilet:

1. Begin installation work by installing the drain coupling. This process will help determine the height of the toilet.

2. When too high altitude, the coupling may be cut off. If the height is insufficient, a section of sewer pipe is added.

3. Measure the distance of the panels for constructing the formwork. Increase the distance by a few centimeters for extra space.

4. Using a tape measure, you should measure the interval between the place where the fasteners are attached. The standard distance is 20 cm.

5. After taking measurements, transfer the data onto plywood sheets to make the formwork panel. Chipboard, plywood or other boards are suitable as materials for the shield.

6. Check again that the measurements taken are correct.

7. Cut off the threaded rods. The length of the rods is the distance between the end point of penetration into the wall, the interval between the wall and the toilet, the installation length of the toilet and the end for screwing on the nuts.

8. There are two ways to attach the rods:

wall mounting, which is carried out with a washer and a nut m 20, the simplicity and versatility of this method make it more popular, in order to attach the rod you just need to drill a hole in the wall, put on the washer and tighten the nut, this method suitable for any walls;
in the absence of access to outside walls, secure the rod with glue or special means, for example, “chemical anchor”, Drill a hole in the wall, the minimum length of which is 14 cm, clean it from dust, fill it with glue and install the rod, this method is suitable for walls made of concrete, brick, foam blocks, wood,

9. After the formwork is assembled, a structure consisting of three panels is obtained, which has holes for installing rods.

Advice: Before fastening the formwork panels, the coupling outlet should be closed using plastic bag, so that concrete and dirt do not enter the drainage system.

10. Correct assembly wooden shields checked by the building level. To make the formwork more stable, install the rods and tighten the nuts.

11. Try on the toilet bowl, installing it in its future location after completing the formwork. If there are any shortcomings, it is not too late to correct them.

Tip: In order to ensure that after pouring the formwork with concrete there is still space for connecting the toilet, you should attach a small rectangular piece of foam plastic to the rod.

12. After completing the preparatory work, begin pouring concrete. To prepare concrete mortar for one part cement, take two parts sand, three parts crushed stone and a seventh part water.

Tip: To make the concrete lay easily on the surface, it is recommended to add a little liquid soap to the water.

13. To lay concrete, use a trowel and place it in small portions. Gradually leveling the surface.

14. The rods for installing the toilet should also be covered with polyethylene to prevent concrete from getting on them.

15. To compact the concrete, use a long rod, which gradually pierces the poured surface, paying attention to the corner places.

16. After pouring the formwork, 7-10 days must pass before it is removed.

17. To connect the cistern, use flexible PVC corrugation. Insert it into the toilet hole and secure it with sealant.

18. Secure the pipe in this position and leave for 24 hours for the silicone to dry completely.

Installation of a wall-hung toilet

1. To reliably seal the joint between the toilet bowl and the rubber ring, apply silicone around the entire perimeter of these devices.

2. Place the toilet on the rods and tighten the nuts.

3. Wait 12 hours for the sealant to cure.

4. Connect the toilet to the sewer drain.

5. Install the toilet lid.

6. To produce finishing finishing works concrete base use any moisture-resistant materials.

Installation of a wall-hung toilet with installation

Most frames for wall-hung toilets allow height adjustment. Before installation, you should take measurements and make markings. Before installation, it is recommended to study the instructions, which usually indicate the interval between the cistern and the floor. average value this distance is equal to one meter.

Before the beginning installation work, take care of the outlet of the sewer and water pipes. The frame is fastened using anchor bolts. They are able to fix it in one position and ensure the immobility of the structure.

When installing the frame on wooden floor, you should use the most powerful wood screws.

Before fixing the installation, you should once again measure the evenness of the structure. Use a regular level to level the frame. Measure front, back, top and bottom. For fixation correct settings use studs and rods that can temporarily attach the frame to the wall.

The height of the bowl is selected in accordance with individual parameters living people. Average height, which is optimal for the average adult is 400 mm.

To connect the toilet, use a flexible hose; to connect to the water supply, use a metal hose to ensure the reliability and durability of the connection.

Tip: Close the valve on the cistern while connecting the toilet to the water supply.

For exterior finishing use any materials that must be waterproof.

Do not block access to the drain tank in order to carry out maintenance or repair work at any time.

Installation of a wall-hung toilet video:

If you have chosen a wall-mounted toilet for your bathroom, you should remember that the process of installing it is very different from traditional options. It is much more complicated, and the work requires much more time. But it should be noted that even inexperienced craftsmen can do the work, provided that they know all the basic features of the work process and perform all technological actions in the correct sequence.

Main elements of the system

First, let's figure out what the structure consists of and what parts you will have to install during the work process:

Basic structure	It is durable metal carcass, which experts call installation for the simple reason that it is on this frame that the toilet is placed. When choosing, pay special attention to strength, since this unit will bear the main load. It is also important to have a system that allows you to adjust the height of the bowl, since the floor level in the room may be different
Tank	It is made of plastic and has a shape that allows it to be placed inside the installation. There is a button on the front that is connected to the drain mechanism, through which access to the inside of the system is provided for maintenance and repair, so it is better if its size is large. It’s good if the design is two-button, this saves water
Toilet bowl	It can have a variety of configurations and colors; you choose the option that will suit the interior. It is also important that the design ensures ease of use, so it is better not to buy outlandish shapes. The manufacturing material is most often earthenware or porcelain; the second option is more expensive, but it is also performance much higher
Fasteners	It should be included in the kit, you need to check the presence of all the necessary components, their number is stated in the accompanying documentation. If the fasteners raise doubts about their strength, then it is better to purchase more reliable options with the same configuration

Important!
In addition to everything described above, you will need a branch to connect to sewer pipe, as well as water supply in.
These are the basic elements, although anything else may be used depending on the specifics of the object.

Description of work

Now let's figure out how to properly install a wall-hung toilet; the whole process can be divided into two parts - installation of the supporting frame and work on finishing and fastening the outer part of the structure.

Installation installation

If everything required is at hand, you can begin to carry out the work; they are carried out in the following sequence:

First of all, the location of the structure is determined, it is important that all communications can be brought there without problems, and that the structure does not interfere with movement. The system can be hidden behind flat surface walls, when the walls are made of plasterboard, and may have the form of a protrusion if you do not want to reduce the space in small room. Marks are made on the surface that will serve as a guide for further work;

Next, you need to bring water and sewer pipes to the approximate location of the toilet. If they will go through the wall and screed, then take care of this issue in advance so that later you do not have to make the grooves with a hammer drill. The sewer outlet requires special attention; it must be positioned as accurately as possible, so when installing the liner, place the frame against the surface to make sure that everything is clear;

Then the frame is set and an inspection is carried out to determine whether it fits tightly to the surface, and whether there are any obstacles that need to be removed (mortar sagging, screed unevenness, etc.). After this, the holes that will need to be drilled to attach the structure to the wall are marked; accuracy and precision are important here;

Drilling is done with a hammer drill, holes are made in the floor and wall according to the previously applied markings. The diameter of the drill must match the size of the dowels or anchor bolts used. When working, try to always hold the tool so that the drill is positioned strictly perpendicular to the surface of the wall or floor, otherwise the fasteners will be positioned crookedly;

After drilling, you need to attach the frame and make sure everything is fine. Next, fasteners are taken and the structure is carefully fixed to the surface of the wall and floor. Before final fixation, it is important to check the position of all planes using building level so that you don’t have to redo the work later;

Do not forget to fix the tank and other components on it before attaching the installation., since it is much more difficult to do this later. At the end of the work, make sure that all connections are reliable and there are no backlashes;
Next you need to set the corrugation correctly, which will connect the toilet to the sewerage system, everything is produced for this necessary measurements and the element is placed at the desired height. You shouldn’t fix it right away, as you need to make sure that everything is correct. You put the toilet bowl on the studs, and if all the elements fit together exactly, then the bowl can be removed and the liner can be fixed in the desired position;

Naturally, before installing a wall-hung toilet, you need to supply water to the tank. If for floor options optimal solution is a flexible liner, then for wall systems experts recommend using the rigid version. It is much stronger and more durable, which is very important, because the system will be hidden behind the finishing, and problems that arise may lead to the need to disassemble part of the wall.

Finishing and fastening of the bowl

Installing a wall-hung toilet is a time-consuming process, mainly due to the fact that you need to finish the structure and close it.

Let's describe the workflow step by step:

First of all, you need to build a frame from a plasterboard profile around the structure; this process is simple; it is important to use reliable elements, take accurate measurements and securely fasten them both to the wall and to each other. If the space is not wide, then the entire surface is sewn up; the photo below shows exactly this option for carrying out the work;

After installing the frame, you can begin to cover it, for this you need to take moisture resistant drywall 12 mm thick, it is a durable material that works perfectly in rooms with high humidity. Measurements are taken and the sheet is cut into pieces of the desired configuration, Special attention take the time to cut out a hole for the button, it is better to do this in a single sheet than to combine several pieces around it, the fewer seams the better;
Fastening is done using special self-tapping screws with fine pitch; they are located at a distance of 20 cm from each other, thus ensuring high reliability of the structure. Do not press the fasteners into the surface too much - you will simply push through the drywall;

Further work depends on which finishing option you have chosen. If the option is to be painted, then the base is puttied until a perfectly flat plane is obtained, if applied decorative plaster, then again you need to putty the surface, and then apply one or another composition. If you decide to do tiling, then there is no need for leveling; you can simply seal the seams and prime the structure;

Important!
To make the tiles stick better, some experts recommend drilling holes in the drywall, glue will get into them, and the ceramics will stick much better.

When the finishing is complete, you need to install the button, or rather its decorative top part, in place and attach the bowl. This is done very simply: it is carefully hung on the studs, after which you need to combine and fix the sewer outlet and the water supply for flushing - everything is quite simple, accuracy and precision are important here. After making sure that all joints are secure, you can attach the toilet;

The last stage is to turn on the water and test flush; it is important to check whether there are any leaks and whether the system as a whole is working normally. If everything is as it should be, then the work can be considered successfully completed.

Conclusion

It’s not enough to choose a high-quality wall-hung toilet - how to install it will take much longer to figure out, but you’ll get excellent result. The video in this article will help you understand the issue even better, but if you still have questions on the topic, then ask them in the comments.

Conventional floor-mounted toilets have been replaced by wall-hung structures that do not take up floor space and look more modern. It is not surprising that wall-mounted models have begun to push traditional products out of the market. Installation suspended structure more complicated, takes longer and costs more, but you can save money if you consider an option such as installing a suspended wall-mounted toilet with your own hands.

Internal structure and principle of operation of the design

If you look into design features products, it becomes clear how to install a wall-mounted toilet.

The design of the wall-mounted product is such that the only visible element is the toilet bowl

The first element is a strong steel frame, which is the base to which the visible part of the structure is attached - the toilet bowl. It is with its installation that the installation of a wall-hung toilet begins. The frame is securely fixed to the wall and also fixed to the floor - as a result, it must withstand the weight of a heavy person.

Accordingly, to weak walls (for example, made of plasterboard) this design installation is unacceptable, since the wall simply will not hold up. The frame is equipped with a device that allows you to adjust the height (400-430 mm) at which the product bowl is mounted. It is suspended from the frame using special pins - this is the main fastening of the wall-hung toilet.

Often two installations are installed simultaneously - for the toilet and for the bidet

The second element is a plastic cistern hidden in the wall. Its shape differs from the traditional one, since the container must fit into a narrow structure. It is mounted in a steel frame and insulated special material, eliminating the appearance of condensation - styropol. The front wall of the tank is equipped with a cutout for mounting a release button device. In case of repair, this cutout is also used. Almost all modern tanks require dosing of drainage: for example, the volume of water discharged can be 3 liters or 6 liters, depending on the purpose.

Flush tanks of a flat configuration are fixed inside the installation

The third element is the toilet bowl, the only visible and actively used structural part. Its shape is traditional, oval, although designer models come in both round and rectangular configurations.

The toilet bowl can be rectangular, or even round shape- it all depends on the designer’s imagination and the client’s desires

There should be no problems with fasteners, since the product comes with a set of necessary details and tools and installation instructions. Sometimes it is necessary to additionally purchase Teflon tape, a polyethylene outlet, flexible hose, studs.

Installation technology

Installing a wall-hung toilet using a special frame installed in the wall is more expensive, but more reliable and faster.

The installation must be mounted to the floor and main wall

Installation steps:

Installation of a steel frame - through special holes it is attached to the main wall and floor using dowels. Sewer and water pipes are installed at the installation site. The frame (installation) should be checked for evenness using a level. It must be clearly parallel to the wall to which it is attached. At this stage, the installation height of the wall-hung toilet is also set - 40-43 cm. It depends on the height of the apartment owners.

The height of the toilet bowl is adjustable during installation

Water supply to the tank. It can be flexible or rigid. Experts insist on the hard version, as it lasts much longer. While the liner is being installed, the valve in the tank is closed.

During work, the water drain from the tank should be shut off.

Connecting the toilet to the sewerage system. The toilet outlet is inserted into the sewer outlet and the connection is secured using corrugations. After installation, it is necessary to test the system - do a test drain. To do this, the toilet bowl is temporarily completely screwed to the frame. It is then removed again, as it is usually installed at the final stage.

Many installation kits are connected to a sewer pipe without the use of corrugations

metal profile

detailed diagram

required holes

An improvised shelf above the toilet and bidet can be used for decoration or necessary things

ceramic tiles

finishing material

The wall cladding behind the toilet should be in harmony with the rest of the room’s decoration

The final stage is the installation of a wall-mounted toilet, specifically its bowl. It is hung on a designated part of the steel frame using two pins.

Sheets of plasterboard with lining cover the installation and the flush cistern, leaving the toilet bowl and flush button

Particular attention should be paid correct installation installation, since the correct execution of subsequent work depends on it.

Installation of a toilet without installation, on a concrete base

Sometimes people are interested in how to install a wall-hung toilet without installation. Of course, installing a toilet on a frame can be replaced with a cheaper option - installing it on a self-made concrete base.

The flush cistern is installed in two ways: either mounted in the wall with flush buttons, or placed in a standard manner above the toilet bowl in a manufactured base.

Wall-mounted toilet mounting diagram: 1 - 2 rods mounted in the wall; 2 - monolithic concrete base; 3 - drain pipe

Let's consider the most economical option.

To install you need to prepare:

about 40 liters of M200 concrete;
boards for formwork;
nuts, washers, wood screws;
2 threaded rods 2 cm thick (length from 50 to 80 cm);
piece plastic pipe(length – 8 cm or more, diameter – 11 cm);
drain coupling;
silicone sealant.

Procedure:

They start by securing the rods in the main wall. In the future, the toilet bowl will be “planted” on the outlets of the rods. The result is a fairly stable structure that can withstand a weight of 400-500 kg.

The dimensions of the concrete base are calculated taking into account further dismantling of the formwork

Install the formwork. Calculate the distance between the holes for fasteners and mark the fastening points on the formwork.

Calculate the length of the rods: sum up the thickness of the recess (about 15 cm), the distance from the toilet bowl to the wall. To fix the rods in the wall use chemical anchor– special adhesive for concrete.

After installing the pins and installing the formwork, try on the toilet bowl. The holes for fastening must coincide with the outlets, the outlet hole must coincide with the outlet of the coupling.

The concrete base will finally harden only after 2-3 weeks.

Begin concreting, maintaining drainer polystyrene foam. The result is a monolithic block with a fixed open coupling and protruding pins.

The concrete base should include pins for the toilet bowl, a coupling outlet for the flush and space at the top for mounting a cistern.

There is no need to think about how to install a wall-mounted toilet on a prepared base - the subsequent steps are no different from installing a conventional one floor-standing toilet: connect the drain, seal the connections, install the bowl on the pins, tighten the nuts. The flush cistern is fixed above the toilet bowl.

The concrete base and drain pipe can be covered with sheets of plasterboard, leaving an opening for access to the drain tank

Installing a wall-hung toilet like this yourself will save the family budget, since expensive installation is not required.

From the author: Hello friends! Agree, it’s good when you have a spacious apartment, or even a house built in accordance with personal preferences. As a rule, all the rooms in such dwellings have quite decent dimensions, because comfort is the most important thing that we want to get from a home. But still, more often there are situations when we are forced to live not in the ideal, but in affordable housing. Take, for example, the well-known “Khrushchev”. You can still come to terms with the size of the rooms in it. In principle, there is room to spread out, and not everyone likes huge halls.

But the bathroom is eternal headache owners. As a rule, there is space for either plumbing or a person. You can still go there, but you can no longer turn around more or less freely. Therefore, in such cases, there is only one way out - to choose the most compact equipment possible. In today's article we will talk about how to choose and how to install a wall-hung toilet. This type of product can save much-needed space in the room. Of course, its installation is more complicated than in the case of ordinary sanitary ware. But believe me, the opportunity to free up space will make you very happy in the end.

Advantages and disadvantages

Many people are very wary of such “delicacies”. We are accustomed to seeing toilets in the guise of equipment firmly standing on the floor, reliable and strong. Hanging options seem more flimsy, and in general, people usually approach anything new with caution. Let's look at what positive and negative features are characteristic of this type of sanitary ware:

aesthetic appearance. An ordinary toilet looks rougher and even, one might say, frankly. Whereas the models attached to the wall are beautiful and laconic;
ease of cleaning. Usually, when cleaning the bathroom, the toilet “leg” causes a lot of problems, especially in a cramped room where it is difficult to bend down. You have to get close to it, and then carefully clean all the bends that are there, while being in an uncomfortable position. With pendants, you can forget about such difficulties, since there is no leg - no problem;
all communications and the water tank itself are hidden in the wall. On the one hand, it is beautiful and, again, aesthetically pleasing. No pipes disturb the external harmony of the room. On the other hand, if something hidden suddenly breaks, problems may arise. Firstly, if there is a leak, it is difficult to notice quickly. Secondly, the repair will not be so simple, since the elements sealed in the wall will have to be somehow selected. Although I saw quite convenient options, when in a false wall at the level of placement of such equipment - in particular, problem areas such as joints, valves, etc. - a door is made. Outwardly, it does not stand out too much from the surface, since it is finished with the same decorative material, which is the whole wall. At the same time, the issue of access to communications is resolved easily and simply;
space saving. We have already touched on this issue above, but we should clarify this point. It is physical savings in terms of the size of the room that you will get about fifteen centimeters, no more, since some part will be occupied by a false wall, which we will talk about below. But visually it will become much more spacious. And then, in especially critical cases, the space under such a toilet can also be useful for placing some necessary things. So, in any case, there is a spatial benefit;
Some people have doubts about whether such equipment can withstand heavy loads. Such fears arise especially often among those who weigh a lot. Purely psychologically, an object hanging on the wall does not look very reliable, so obese people are usually afraid to use such things. In fact, the mount is strong enough to support a weight of about 150 kilograms. so there is nothing to be afraid of if your body weight does not exceed these limits. Otherwise, of course, it is better to take regular option, installed on the floor;
price. Here the wall-hung toilet has nothing to brag about: it is frankly more expensive than its floor-standing counterpart. True, it cannot be said that this option is available only to wealthy people. The cost range is quite wide, so you can still choose a model that suits your budget;
complexity of installation. This can also scare off many, especially beginners, masters. In general, not in vain, since it is installed correctly hanging model with your own hands - it’s not that simple. You will have to install not only the equipment itself, but also make a false wall. However, the difficulty of this activity is not prohibitive. So, with a little patience and attentiveness, you will definitely succeed.

Varieties of design

In principle, the essence of all wall-hung toilets is the same: they consist of a tank, a bowl and an installation. Of course, each of these parts is different from those characteristic of floor models. The bowl has a different shape, the tank is flat and plastic. It’s worth talking about installation separately.

Installation

The installation is, in fact, the very structure thanks to which all other elements are safely held in suspension. It is a strong frame made of steel.

There are two options for mounting installations: block and frame. The first ones are distinguished by their compact sizes - as a rule, the dimensions are half a meter wide, a meter high and 10–15 centimeters deep. The volume of the drain tank, which is mounted on such a frame, varies from three to five liters.

Block installation is mounted only on the wall, without the floor. Therefore, the foundation must be very reliable. That is, only suitable for securing such a structure, but not an interior one. This must be taken into account when choosing.

Frame installations are larger in size. Their width can range from 50 to 60 centimeters, height from 80 to 140 centimeters, and depth varies from 15 to 30 centimeters. The tank installed on this structure can hold from 6 to 9 liters of water.

Such structures are not hung on the wall. They are placed on the floor and attached to it. Some models are additionally fixed to the wall, but it does not have to be load-bearing.

Bowl

The main operational location of such a toilet can be round, rectangular, egg-shaped, etc. - modern market offers many various options, among which you can choose the one that suits your taste. The bowls also differ in size. They can be compact, up to half a meter long, medium-sized, like regular toilets, and also large, the length of which varies from 65 to 70 centimeters.

In addition, you can choose models with some features:

bowls without a rim - there is no usual protrusion in the upper part, which makes cleaning the product much easier;
built-in bidet - in the normal state the washing nozzle is hidden in the back wall of the bowl, and if necessary it extends;
backlight As a rule, it is connected to a motion sensor, which makes using such a toilet extremely convenient at night or when there is a power outage in the house.

Of course, the design of the bowls can be very diverse. There are options made of glass, faience, metal and other materials, with and without drawings. The color range is also very wide. Here the choice depends solely on your personal preferences.

Installation procedure

Installation of wall-hung toilets can be done either with or without installation. The first option is more popular, so we’ll start with it.

Installation with installation

The first thing to check is the strength of the wall and floor. Ideally, they should be concrete. We remind you that if you decide to use a block version of the frame, then the wall must be load-bearing. The reliability of the installation of suspended sanitary ware depends on the strength of the connection between the frame and the base. So, let's get to work.

We start, naturally, with the markup. We need to mark on the wall and floor all the points where fasteners will be placed, as well as the location of the sewer outlet and water pipe. To make it easier, first mark the place where the cistern will be fixed. Usually it is located a meter from the floor, and the bowl is half a meter.
Now we need to let you down water pipe to the corresponding mark. To do this, you can use a flexible hose, but the best option would still be metal-plastic. It is more reliable and durable.
We also bring to to the right place sewer outlet. If your installation is of the frame type, then pay attention to the fact that it has a specific section for this pipe, according to which you need to place it.
Next we proceed to fixing the frame. We drill holes in the places marked for fasteners; for this we will need a hammer drill. We install the dowels, then the frame, fasten it with anchor screws. Fixation is carried out first on the floor and then, if necessary, on the wall.
We connect the drain tank to the water supply pipe, and also attach the sewer outlet to the installation.
The steel frame has holes for screwing in special pins that come with the equipment. Put these elements in place.
Now you need to mount the false wall. The best option For this purpose - drywall. But keep in mind that not everyone is suitable. Regular drywall tolerates exposure to water very poorly. Since we are talking about a bathroom (and it is often also combined), care must be taken to prevent the destruction of the wall. Therefore, use only waterproof drywall. Externally, it differs from ordinary material in its greenish surface. Cut holes in a sheet of drywall for everything that will stick out from it: a sewer pipe, pins, a drain button, and the like. Mount the wall and then produce it finishing. This can be done using paint or tiles.
We put the bowl on the pins, press it properly against the wall, and secure it with bolts.
To complete the process, we install a drain button.

Let's check our design. To do this, open the valve on the supply pipe cold water, wait until the tank is full, then drain. We repeat several times. If everything is in order - performance is at the required level, there are no leaks, etc. - then you can put it into operation.

Installation without installation

You can do without a steel frame, but such installation is carried out only on load-bearing wall. You will need metal rods length of 30 centimeters or more, wooden panels, concrete, toilet structural elements and wall cladding material.

We take it out from the wall.
At the required height from the floor (that is, where the bowl will be fixed), we drill holes and install metal rods in them. It is advisable that the wall is drilled through and the rods are secured with nuts on the reverse side. If this is not possible - for example, there is a neighbors apartment on the other side - then do not drill right through, but add glue intended for concrete products into the holes before installing the rods.
Next, we install formwork from wooden panels around the sewer outlet and rods, creating a box of three walls. Cover the pipe with thick film. We fix a piece of foam plastic on the central panel in the place where the bowl will be connected to the drain.
We pour concrete into the formwork. You can make it yourself from one part cement, two sand, three crushed stone and required quantity water. We add soap as a plasticizer.
After pouring, wait about a week for the structure to dry. We remove the formwork.
We mount the bowl and tank in the appropriate places, connect the communications.
We sew and finish the wall.

Both installation methods are not so simple. But using the installation is still more convenient and takes much less time. With concrete you will have to tinker as much as possible. Besides, similar works They are not particularly clean, and the block around the pins will take a whole week to dry.

On the other hand, this option is cheaper. So, if you prefer to spend effort rather than money, then go for it. Good luck!