A durable front door is a guarantee of peace of mind for the owners. But appearance is no less important than its security qualities. Immediately after installation front door The question arises: how to improve the slopes? There are many options, but I will focus on finishing the slopes of the front door with artificial stone.

Gypsum stone has a large number of options, both in relief and type of stone, and in the thickness of the tiles. For this job I used gypsum stone thin-layer slate with a thickness of each tile from 2 to 2.5 cm, depending on the relief in a particular place. The slopes of the front door were level cement plaster. Stone can be laid on a flat cement screed without prior putty.

First, I primed the areas near the front door where the artificial stone will be installed. Then, gradually, from the bottom, she began to lay the tiles on the cream diluted to the thickness gypsum putty. When I reached the corner, I simply sawed the stone with a hacksaw to the required size. If there are corner elements, door trim decorative stone it turns out much more beautiful than connecting a relief stone at the corners different tiles. The photo shows that this corner element is precisely cut out according to the relief and looks complete.

WITH outside The walls were wallpapered. You can't put stone on wallpaper, so I just stationery knife I cut off pieces of wallpaper and installed sawn pieces of stone onto the resulting areas. It turned out like a torn stone on the slopes. I carefully rubbed the seams at the joining points gypsum putty, trying not to run into the general terrain.

After drying, the stone needed to be painted. I did this using stone varnish, which I tinted in chocolate color. I applied it with a brush and immediately, until the varnish was absorbed, I wiped off the protruding areas with a damp sponge. Plaster absorbs quickly, so this must be done immediately. The result was a very ancient-looking stone, as if weathered by time.

Lining the inside of the entrance door with artificial stone can be done with either gypsum stone or cement stone. The main thing is that the cement stone is not too massive and does not look rough. And in this case it is necessary to cover the slopes of the front door using tile adhesive rather than gypsum putty. This way the adhesion of the materials will be better, and the stone around the door will last for many years.

7367 0 0

Finishing openings: how to choose material and design

When remodeling and replacing doors and windows, questions always arise: how to design the openings, what design ideas Can you implement it in your home? In this article I will describe which decoration of a doorway without a door is most advantageous in general interior. I’ll also tell you how you can decorate the entrance door and window openings.

Options design design There are many openings. But it is important to consider the finishing possibilities. So, the materials used for the living room door block, may not be suitable for the kitchen due to their characteristics (for example, moisture resistance).

Artificial stone for cladding

Today fashionable finish doorways with artificial stone. After all, his choice is so wide that he guarantees spectacular design in any .

Artificial stone is chips made from natural rocks. Dyes and polymers are added to it ( polyester resins), improving appearance and providing strength. With them, imitation of texture and appearance natural stone perfect.

Decorating a staircase opening with synthetic stone is a popular and beautiful solution.

It’s easy to choose the material to suit your interior, because the advantages are undeniable:

• a variety of decorative stone designs is provided by crumbs of malachite, limestone, shell rock, jasper, and marble;
• original " wild stone» — without processing;
• there are convenient corner elements for corners;
• its colors range from cold gray to warm ocher;
• during installation, you can make the border smooth or leave a “natural” torn edge.

When decorating a door block between rooms, designers prefer a small and shallow relief pattern so that its bulkiness does not “press.”

Installation specifics

With such cladding with your own hands, significant weight is taken into account of this material and its thickness. Therefore, this section of the wall is treated twice with a primer.

After drying, it enhances adhesion (adhesion of surfaces) of all installation building compositions. In this case, pasting with artificial stone will be more durable, since the material will adhere more firmly to the wall.

1. We fix the decorative stone on the rough opening tile adhesive. And on a completely flat surface - “ liquid nails" When covering a block combined with a kitchen, the strongest glue is used, because steam and heat will affect the durability of the installation.
2. When creating a cold opening between the entrance doors, use cement composition. They work with it in the same way as with glue, but apply only to a damp surface.

• We will get a uniform size of seams from auxiliary plastic or wooden planks. They need to be temporarily laid between the tiles, straightening the rows. When the glue dries a little, we take these calibration elements out of the seams.

• If the adhesive solution is on plaster or cement based, then any excess that appears must be removed immediately.

• The seams must be smoothed over the next 30 minutes before the composition sets.
• After drying, fill the gaps with grout of the desired color.

It is easier to decorate without jointing - no need for strips, caulking or grouting work.

Cladding with decorative stone is labor-intensive, and the material is expensive. But there are also less expensive ways, for example, PVC finishing panels.

Plastic elements

Such plastic kits are designed for rectangular and arched windows and doors, different widths and heights. The trims are white or with a textured wood pattern of different shades. That is, their choice is large, and installation is quite simple.

Let's look at the features of decorating a doorway with plastic panels.

The finishing kit already includes the necessary parts:

• Platband. We fix it on the wall outside the opening. It consists of 3 slats - top and 2 side. For an arch, the upper part is curved.
• The kit for an opening without a door includes 2 trims - on both sides.
• The additional strip corresponds to the thickness of the opening and is mounted on its walls. In the arch it repeats its configuration. After all, there are kits made of flexible plastic. But when purchasing, make sure that the parts are flexible.

Price and aesthetics plastic trim door blocks pleases. We also include the following advantages:

• ease of installation - you can do it yourself;
• shock resistance;
• ease of care: this material does not collect dust - a damp cloth will remove dirt;
• the ability to disguise communication cables - there is an entrance for them near the baseboard and channels for wires.

Extensions and platbands are glued to the walls with “liquid nails.” Some of these products are fixed with locking connections with guides; they are included in the kit. And wider holes can be lined with ordinary plastic panels, i.e. for walls and shelves.

And finishing a window opening with plastic is even simpler - it’s easier to work with short panels.

The variations in plastic window design are endless. The outside of the holes can be lined with fashionable vinyl siding.

Lining an opening with PVC elements will last more than 20 years.

For lovers of the classics, there is an alternative to modern siding - plastic stucco.

Artificial stucco molding

Stucco molding around the perimeter of the door block and columns with pilasters, capitals is a prestigious choice for Venetian style. Previously used plaster stucco, the columns were made of limestone.

Now this decor is made from polyurethane. It is lightweight, sticks well with polymer adhesives or “liquid nails” and even “Moment”. By the way, polyurethane can be painted to imitate stone, wood, or gloss.

Eat polymer parts with relief, in the form of moldings, without floral patterns. Designers combine them with inconspicuous platbands in an arch or rectangle of a balcony opening.

Of course, in small apartments these details will clutter up the space. But they will pompously decorate a large hall.

Cladding on plasterboard

Only this material pliably forms a part of a complex configuration, for example, a curved arch. However, the installation work is not easy - you will need a lot additional material: profiles, corners, screws. And after installation, drywall requires finishing: putty, paint or wallpaper.

Typically, arched blocks without a door are sheathed with plasterboard. A semicircular opening will soften the corners, as if raising the low ceiling and lowering its high and uncomfortable counterpart. The arch is appropriate between the living room and the hallway or kitchen. Also often found is an arched exit to a loggia or balcony.

Openings without doors unify rooms in an original way, harmonize with the overall style, and expand the area. The quality of finishing and its design is especially noticeable at the border of the hallway and living room or when connecting to the loggia. This design advantageously emphasizes the interior of the premises or zones the space.

Wood finishing

Of course, decorative platbands decorated with carvings are expensive. But they are beautiful and durable. By the way, with the renovation of the interior, we can repaint them or change the shade with varnish.

Exact imitation from chipboard

Decoration of the entrance opening is also in demand chipboard doors. It is acceptable in the interior of any style. This wood-polymer composite from veneer and synthetic resins. And the marking accuracy and good tool will reduce time and material when designing openings of any configuration.

Facing the entrance opening

Traditional cement strainer used to decorate the front door. Design without cladding requires skill or maximum patience:

1. A solution is made from sand, cement, and water.
2. Using a trowel, apply it to the opening, level it and remove smudges.
3. With the beacons exposed, the solution will lie more evenly. Lighthouses are flat wooden slats or metal profiles. They are attached vertically with alabaster.

In the photo there is a beacon for the screed.

1. When the beacons harden, all the gaps are filled cement mortar. Use a spatula for this work.
2. The dried screed is painted with façade acrylic paint.

Finishing with cement will protect the structure from moisture; it will not crumble due to temperature changes. And the surface can be decorated with any finishing material.

Decorating with plaster

Often external finishing impossible without prior leveling with plaster. We need spatulas, a level, primer and dry mix. Remember that it is the primer that will improve adhesion.

A wide spatula or plank will usually make the surface even. We check its general position with a level.

1. First, we seal large cracks and irregularities.
2. We use it at joints plaster mesh. It will hold the mortar on the wall.
3. We check the corners with construction corners.
4. After the starting layer has dried, sand it and cover it again with a layer (for leveling).
5. Then we apply the finishing putty - a paste without large particles. With the final grouting, remove dust.
6. Now we cover the plastered area with water-based emulsion.

Decorating doorways with decorative stone has become commonplace these days. Decorative brick today is considered in the world of designers not only as a high-quality finishing material with a long service life, but also as an excellent design element.

Specifics of the material

Finishing doorways with decorative stone is possible due to its unique technical and operational characteristics.

Advice! Decorative stone is suitable for cladding kitchens, bedrooms, balconies, and corridors.

If you decorate doorways with decorative stone, you can create a comfortable and cozy atmosphere inside the room.

In addition to protecting corners from mechanical deformation, you can also use this decorative material You can give a beautiful appearance to any living space.

Modern manufacturers of finishing materials offer consumers various options colors and textures of decorative bricks, so even the most capricious buyers will be able to make their choice.

When choosing decorative stone as a finishing material, you can not only visually expand the size of the doorway, but also give the interior of the room restraint and seriousness.

Finishing doorways with decorative stone, photo, useful tips, all this can be found in the proposed video

Advice! This finishing material goes well with Roman and Greek wall paintings.

For example, using large mirrors and correct selection brick color, you can achieve an unusual visual effect and make the room longer.

High-quality finishing of doors with such bricks; photographs of the completed work can be found on the websites of design agencies.

Thanks to the use of mirrors and original finish doors with this decorative material, you can get an unusual visual effect, lengthen a narrow room.

By using artificial material you can create the feeling that you are in an ancient building from Stalin times.

Decorative bricks, used in decorating hallways, can be combined with other types of decoration.

For example, armed with this finishing material, it is quite possible to create a wall picture on the wall.

Advice! If you want to bring into the premises unusual elements, it is quite possible to create an arch from decorative bricks.

They will help you recreate the atmosphere of the eighteenth century in the room, making the interior serious and strict.

Interior specialists use this finishing material in cases where they need to separate one room from another.

Thanks to decorative stone, you can create unusual slopes in the doorway.

Brick different colors helps to create unique compositions that will harmoniously complement all other elements of the created interior.

Decorative brick is used not only in living rooms, hallways, but also in other rooms.

Attention! Classic brick is suitable for creating a discreet, attractive, serious interior.

This material in residential areas is not only quality material finishing for a long period of time, but is also considered in the world of modern design in a great way registration

Material classification

In order for your idea to become a reality, you first need to think about choosing starting materials for work. Currently, there is a division of this finishing material into two large groups: artificial and natural stone.

Advice! Professionals advise choosing a natural material for residential premises, while an artificial analogue is suitable for corridors and bathrooms.

Among the main distinctive characteristics natural material, which made it an attractive way to decorate premises, mention should be made of its environmental friendliness, durability, and aesthetics.

Among the main and few disadvantages inherent in decorative bricks, we will call it high cost.

Artificial stone is practically not inferior to its natural counterpart in terms of performance characteristics, as its manufacturers use innovative technologies.

Not all owners square meters can afford the luxury of finishing doorways with natural stone.

Advice! Among the most inexpensive options Natural stones that are suitable for decorating doorways include marble, onyx, and sandstone.

As available material, used for finishing, can be called numerous artificial stones, which in appearance are similar to natural stone.

Finishing features

Among the main elements for decorating which artificial stone is used, professionals highlight the front door. Finishing is carried out not only for the exterior, but also for slopes located indoors.

In case of facade works, finishing is carried out in conjunction with the cladding of the base. For example, you can choose sandstone to decorate a building.

Having selected stones of approximately the same size and shape, it is advisable to check them for layering. To do this, the stones are laid out on a flat and clean area and washed with a jet clean water. It is advisable to wait until the stones have completely dried and only then begin finishing work.

Advice! In order not to waste time, you can start preparing the base itself while the stones are drying.

First you need to evaluate the quality of the surface that you plan to decorate. If necessary, it must first be primed so that no problems arise during the process of fixing artificial or natural stone.

Next, you need to prepare the glue to fix the prepared decorative material. Professionals advise beginners not to experiment, especially if they intend to fix the finishing material, but to purchase ready-made glue.

In this case, you can not only significantly save material resources, given the high cost of natural stone, but also save yourself from using low-quality adhesive.

Property owners who already have some experience working with stone try to choose finishing works mixture CM 11. What is the reason for this choice? This composition is not only suitable for interior and exterior work, but is also absolutely safe for human health.

In addition to this mixture, the manufacturer of which is a German company, you can also choose mixtures offered by domestic manufacturers for decorating internal and external doorways with natural and artificial stone.

Professionals recommend that those owners of urban and suburban real estate who decide to use stone to decorate their homes first choose color scheme finishing material. In addition, it is advisable to think over the version of the drawing that will be created after all finishing work is completed.

For example, you can initially outline the contours of the outline, which will be made of stone, and only after that begin direct repair work.

Conclusion

Such a decorative material as stone is a popular and common material in modern construction. Its unique mechanical, physical, and operational characteristics have already been appreciated by craftsmen in the finishing of residential and non-residential premises.

In addition to the beautiful appearance that is obtained when using this decorative material, we also highlight the long service life of this material.

The interior of the hallway should not be given less attention than other rooms, because this is the first thing guests see. A very stylish look is given by artificial stone, which is used as the main material or as an additional accent. Create original design you can do it yourself, since finishing the hallway with decorative stone has a fairly simple technology.

Types of coating

Before you start work, you need to choose the right finishing material. It is made on the basis of concrete and gypsum with the addition of dyes. Both types have their own advantages and disadvantages, so it is better to study their characteristics first.

To the advantages concrete products relate:

Walls decorated with such stone can be easily cleaned of any dirt, and the worn surface can be quickly restored with paint. If you accidentally touch the finish with something hard, there will be no marks left on it and no cracks will appear.

Flaws:

• heavy weight;
• high price;
• processing complexity.

To cut individual fragments when laying, you will need a grinder and a diamond wheel, as well as some effort.

Advantages of gypsum coating:

This stone is chosen for finishing plasterboard walls, which cannot be subjected to heavy loads. If you can’t find the right color, there are unpainted products on sale that you can paint at your discretion.

Flaws:

When dirty, this finish should not be wetted or rubbed vigorously so as not to damage the surface. Treating the stone with a special impregnation or varnish will help to avoid such damage. acrylic base. Also on sale is gypsum stone with polymer coating– it’s a little more expensive than usual, but it’s not at all afraid of moisture.

If you wish, you can do it yourself: for this you will need a plastic or silicone mold, dry gypsum mixture, coloring pigments. Buying all this is not a problem, in every hardware store big choice mixtures and forms. Making finishing materials yourself takes more time, but saves money on repairs.

Prices for facing stone

Facing stone

Preparation for finishing

First you need to calculate the amount of material. If the stone will cover the entire area of ​​the walls in the hallway, you should subtract the area of ​​the openings and add 10%. If the decor will be located around openings, niches, in separate fragments on open walls, draw a rough sketch of the decoration and take measurements of each area. Then add up the area and add 10-15% for trimming. When purchasing material, you should remember that the amount of stone with an angular shape is calculated in linear meters, and of a regular shape - in square meters.

Additionally you will need:

Artificial stone can be attached using liquid nails, cement-based or gypsum-based glue. The glue consumption must be indicated on the packaging, so when purchasing, you should know exactly the finishing area and take it with a small margin.

If you use gypsum stone, you will need a special miter box with high sides for cutting.

When everything you need has been purchased, you should start preparing the surface.

Step 1. Dismantling the coating

If the stone covers the hallway walls completely, the old coating is removed completely to the base. If intended for decoration separate areas, you need to dismantle the coating very carefully. On the wallpaper, mark the boundaries of the finish with a pencil and carefully trim it with a utility knife, leaving a margin of 1-2 cm wide for stones. The wallpaper glue is soaked in water and removed with a spatula, and the walls are thoroughly washed. They also remove the paint if it is peeling or cracked, and clean off any loose plaster.

Step 2. Leveling the walls

The stone must be laid on a level smooth surface– this will facilitate the work process and increase strength decorative covering. Therefore, all small cracks, gaps, and depressions are rubbed down, and if there are differences of more than 5 mm, the entire area is better. Particular attention should be paid doorways: deep cracks may form around the perimeter of the box, to seal which it is recommended to use a cement solution.

Prices for mixtures for leveling walls and ceilings

Mixtures for leveling walls and ceilings

Step 3: Priming

Dry walls must be lightly sanded to smooth out the unevenness of the puttied areas, and then wiped with a rag to remove dust. After this, the surface is treated 1-2 times with an acrylic primer. If there is wallpaper around the perimeter of the areas to be treated, the primer should be applied so as to cover an edge 1 cm wide - what will be hidden under the cladding.

Laying stone

Decorative stone has uneven edges and consists of different sizes. Laying must be done in such a way that tiles of the same size are necessarily interspersed with larger or smaller fragments, and the seams do not coincide either horizontally or vertically. This way the coating will look most natural and attractive. To understand how best to join the stone, you need to lay out the tiles on the floor, selecting the fragments in a certain order.

Step 1. Preparing the glue

Pour dry glue into a container of water and stir well. The ratio of water and glue is indicated on the package, so there is no need to mix “by eye”. Failure to comply with the proportions reduces the strength of the connection or increases the consumption of glue. Kneading is best construction mixer, then there are no lumps left in the mixture. The finished glue should be homogeneous and resemble a thick paste in consistency.

Step 2. Laying the first row

You need to lay out the tiles from the corner of the wall, and this can be done both from above and from below. When laid from top to bottom, the stone is less dirty with glue, and the coating is more accurate. If only the area around the opening is covered, start from the corner of the door. For convenience, the wall can be marked by level horizontal lines every 10-15 cm.

Now you can start installation:

Between the fragments you can leave seams of 5 to 8 mm, especially if the stone is large.

After facing, the joints are filled with putty and jointed, which makes the masonry more attractive. Small tiles can be attached closely, the main thing is that the joints do not coincide.

Step 3: Finishing the corners

For cladding interior and external corners you can purchase special corner tiles, which are more expensive than usual, but significantly simplify the work process. If your budget is limited, you will have to adjust the stone yourself using a grinder or a hacksaw. There are 2 options here - laying the stone overlapping or grinding the edges at an angle of 45 degrees. When using the first option for external corners, the open ends must be filed and tinted, otherwise they will stand out too much. In internal corners Both ends are closed, so no processing is needed. The second option is more suitable for gypsum products, which are convenient to cut using a miter box.

So, first determine required quantity fragments, trim them from certain side, process the sections with a file. Next, the stones are smeared with glue and alternately attached to the walls on both sides of the corner, carefully aligning the joints. When the vertical corner is laid out, you can expand the masonry onto the walls.

Step 4. Decorating the edges of the masonry

The edges of the masonry will look more attractive if the tiles are cut beautifully. The surface of the decorative stone has a clear texture, which makes it easier to trim the outer fragments. You should cut with a hacksaw directly along the contour lines to ensure the most natural cuts. All cuts must be sanded with sandpaper.

Step 5. Sealing joints

Dilute the gypsum putty and carefully apply it to the joints, corners, and around the perimeter of openings and switches. For convenience, you can use a thick bag, for example, a milk bag. One edge of the bag is cut completely, and a small incision is made on the other side. Fill the bag with putty mixture and squeeze out an even thin strip onto the seams. If the solution is applied with a spatula, you should immediately wipe off the excess from the surface of the stone to avoid drying out. After filling the joints, the putty is rubbed with a damp foam sponge and left to dry.

Step 6: Finishing

The dried putty has White color, and therefore the treated areas will stand out against the background of the stone. Paint will help get rid of light spots: in a small container, dilute the pigment to match the color of the main coating and use a small brush to paint the putty areas. When the paint dries, the stone is covered acrylic varnish. In places where the walls are constantly touched, it is better to apply varnish in 2-3 layers.

To make the coating more voluminous, you can highlight the edges of the masonry with golden or bronze dye. There is another option: a coating of the same color, but more saturated in tone, is applied to the artificial stone at an oblique angle. In addition, you can use lighting: light directed from above or from the side makes the masonry much more textured and clearer.

Calculation of decorative stone	Formulas	Explanations
Calculate the surface area intended for cladding with artificial stone	S (wall) = AxB	A – wall length, B – wall height
Calculate the surface area that the corner elements of the decorative stone will occupy	S (angles) = Lx0.2	L – angle length ( linear meters), 0.2 – coefficient
Find total area, which is occupied by all corner elements	S (angles total) = S (angle 1) + S (angle 2)	-
Calculate the area of ​​window and door openings	S=AxB	A – window/door width, B – window/door height
Calculate the surface area intended for facing decorative stone, taking into account the area occupied by corner elements, window and door openings	S (stone) = S (walls) – S (corners) – S (windows/doors)	Increase the resulting area by 10%
How to calculate required amount corner stone elements.	Measure and add the height of the corners to be faced with decorative stone. L (total angles) = L (angle 1) + L (angle 2), etc. Increase the resulting length by 10%	L – length of corners (linear meters)

Video - Decorating the hallway with decorative stone

Many people want to diversify their interior. In addition to transforming the room itself, many try to highlight the doorway, using a wide variety of methods. Decor doorway- this is the first thing guests will see when entering the room. They will definitely pay attention to him. Therefore, it is important to know how to highlight this part of the interior.

Finishing features

A doorway is very often finished without installing a door leaf. In this case you can save large volume funds for purchase door design and its installation. This finish is distinguished by the fact that it is very diverse and original. Most apartments have regular doors, and thus you can diversify the interior. A special doorway can become the highlight of any interior.

A doorway can blur the boundaries between rooms, but at the same time separate them. This design can make the room visually wider and more spacious. The finishing is also distinguished by the fact that in this case the doorway is not necessarily decorated according to the classical rectangular shape, as is the case with door structures, but they give preference to other forms. For example, you can make a dome-shaped, rounded, diamond-shaped, trapezoidal passage.

The doorway is also designed according to the closed type principle. In this case, it is filled with screens and partitions. This solution is perfect for zoning rooms and highlighting different functional areas. A peculiarity of the decoration of the doorway is that it always initially has the shape of a rectangle.

You can change its shape with fancy patterns without having to complex installation, which is a big advantage of this design.

The decoration of the doorway can complement the interior design. So, for classical styles strict standard forms are more suitable, and for modern interiors use newer and unusual solutions. This design can have any complex geometric shape.

Another feature of finishing is that it is carried out in one stage. After this, you will not have to maintain the structure, as is the case with doors. When designing and finishing, you can use absolutely any materials; there are no restrictions on this. In addition, the finishing is distinguished by the fact that it is quite simple; anyone can do it themselves.

A doorway can have doors, an arch, or curtains.

The principle of its design is divided into two large groups:

• with doors;
• without doors.

Options for framing an opening with and without doors in an apartment

Framing a traditional opening involves installing door frame and door leaf. At the same time, the size and appearance of the door can be absolutely any. This is the most common design for entering a room. The door is used to separate rooms; it performs the function of sound insulation and thermal insulation.

But many decide to design a doorway without a door. The door structure is abandoned in the case when the entrance does not lead to a bedroom, nursery or other room, but to a more public room, such as a dining room, living room, hall, kitchen.

Thus, all these rooms unite and make the atmosphere in the house more comfortable.

Cashing the opening of interior products

To frame a doorway, various methods are used, these can be like natural materials, and their artificial analogues.

Often used:

• Plastic materials (PVC);
• MDF panels;
• laminated chipboard;
• Tree;
• Polyurethane.

As a rule, this part of the room is framed with wood. Very often, wooden platbands are made from spliced ​​wood. Moreover, pine very often acts as a source of wood, since it is durable. Wooden trims usually covered with a layer of varnish, it looks very noble. Telescopic cashing is also very popular.

The carved cash looks beautiful. As a rule, carvings are made by craftsmen with their own hands, and each such pattern can be very elegant and unique. MDF trims are more affordable. But at the same time they are not considered to be of lower quality and durability. They are absolutely not subject to rotting and many external influences.

The only one negative trait This material is poorly resistant to moisture. The easiest way to care for plastic trims. They retain their original appearance throughout for long years. Usually, plastic trims have the most interesting and bright design.

They are able to retain their color for a long time.

Plastic is completely insensitive to humidity and temperature changes. In case you want to route electrical wires and cables through the doorway, great solution There will be a PVC frame. This casing has a special cable channel that simplifies this process. Some models look very luxurious due to the fact that they imitate wood patterns in appearance. In general, PVC completely replicates the quality characteristics of plastic.

Platbands are also divided by appearance. Their width can be any, as well as thickness.

All of them are divided into:

• flat;
• rounded;
• curly.

As a rule, these types of platbands are mass-produced in factories.

But carved frames- This is a separate type, which is a product of the hands of a master, distinguished by its uniqueness.

Decoration with decorative stone

A decorative stone can decorate any doorway. Very often it is used after installation iron door. It is able to hide any imperfections and transform the appearance of the opening. Decorative stone is quite durable and looks very elegant.

It is resistant to external influences and looks great in any lighting. During the day it will sparkle in the sun, and in the evening it will sparkle luxuriously in dim light. Decorative stone is now used to decorate the passage using adhesive installation.

Decorative analogue natural stone is lighter and more affordable in cost. You can choose a model of absolutely any color and texture. So, you can decorate the passage with a wide variety of pebbles, creating a unique pattern. The decoration of the corners with decorative stone in the Roman style looks beautiful.

Also, many decorate the opening using the torn edge technique. It involves laying stones in a chaotic, not perfectly even order.

This way you can even create the effect of antique masonry and lay out any fancy shape.

Plaster

Plaster is now very often used to emphasize the bizarre shape of an arched partition. In this case, decorative relief plaster is used. It is also combined with other finishing materials, such as artificial stone and tiles. Venetian and microcement plaster are also used as finishing, since such cladding looks very elegant.

But not everyone can finish a doorway in this way; for this you need to have special skills.

Wallpapering

Using wallpaper, they decorate not only the doorway itself, but also door leaf. Moreover, in the second case, the wallpaper that is most resistant to external influences is used for this, since the door is very often touched with hands. The most simple wallpaper can get dirty very easily, so it is important to use only high-quality and durable coatings. Wallpaper allows you to completely disguise the door, thus hiding the opening.

You can cover the canvas with wallpaper of the same color and pattern, like all the walls adjacent to it. This finishing option is very often used to decorate the passage to the office. If you have an embossed door installed, you can only partially cover it with wallpaper. Using wallpaper you can even create designs on the door leaf. In this case, you can cut them out geometric figures and other fragments.

You can also use wallpaper to highlight the door leaf by contrasting it with bright wallpaper that differs from the color of the walls. Moreover, such a coating can be partially painted to make it more unusual and interesting.

Arched structures are also decorated with wallpaper.

Upgrading slopes with siding

Siding is a finishing material that has an interesting textured surface. It is distinguished by its corrugation. In this case it is used vinyl siding and even steel sheets. This finishing material is perfect for cladding slopes and is quite durable. Moreover, as a rule, it is selected to match the decoration of the windows and the window frames are framed in the same way.

Siding can be easily installed with your own hands and will be quite easy to maintain. Moreover, manufacturers present a wide variety of models from different material, issued in unusual colors. The right coverage can be selected to suit any interior design.

Decoration with stucco

Polyurethane stucco is often used to decorate the doorway. For narrow doorways most often they choose smoother and not too embossed stucco. It is believed that too voluminous textures can visually narrow passages and make the room less spacious. Volumetric stucco molding is most often used to decorate high, spacious doorways.

The stucco molding is fixed using special glue. It is also often coated with varnish or paint.

This design looks very unusual and varied due to the combination of interesting textures.

Tile edging

Nowadays, aisle edging is very popular. ceramic tiles. At the same time, it is very often used gypsum tiles or clinker. Clinker imitates bricks and is perfect for finishing not only door but also window openings.

Typically, such tiles are laid by analogy with brickwork. This analogue looks quite unusual and believable. Smooth tiles are also used to finish doorways. In this case, it is laid out as a mosaic. This design looks very bright and impressive.

Sheathing with plasterboard or clapboard

Lining and drywall are some of the most inexpensive finishing materials. That is why they are often used to decorate doorways. Both of these materials can be easily processed by hand using standard tools. You don't have to do a lot of preparatory work.

As for drywall, it has a smooth surface, which is usually decorated with bright coatings. You can choose any decor option to decorate such material.

It is easy to install and lasts quite a long time.

Decoration with stencils

Nowadays, paintings and paintings are often used to decorate the entrance to a room. unusual drawings. But not everyone can create a beautiful and unique pattern with their own hands. In this case, a stencil is used. This way you can very quickly correctly and evenly apply images to the door leaf or to the edging of arched structures.

The only drawback of this finishing option is that it is quite boring, because the patterns will not represent a picturesque picture, but only patterns of the same type. This way you can decorate the doorway with grape leaves, branches, flowers and other images.

Textile

This finishing option is quite popular. As a rule, various curtains and tulle are hung between rooms, which fill the room with lightness and create an invisible barrier. They fill the design with air, making it more elegant. Curtains are usually chosen from silk, cotton, linen. Thick velvet models are quite popular.

Magnetic curtains are also installed, which are excellent for protecting against insects. There are also beautiful thread curtains in the form of rain. You can hang translucent tulle, which will create a light veil between different rooms.

Facing arches between rooms

As a rule, a room is made more spacious by creating an arch at the entrance. In this case, such structures are often installed at the entrance to the room from narrow corridor. The arch fills it with space and comfort. Arches can have the most unusual and intricate shapes.

In this case, the choice of the shape of the doorway depends on the taste of the owner of the house and the style of the interior.

Most arched structures are symmetrical. For their finishing, the same materials are used on both sides. But in some cases, arches can be asymmetrical in shape and design. For premises in classic style Only symmetrical models are selected. In this case, they are often faced with decorative stone, wood and other natural or imitating natural materials.

Arches with vertical slopes in the form of columns look very beautiful. This solution is perfect for those who adhere to classic interior design. For a more elaborate style, the design of arches with a wide variety of decorative elements is selected. For this purpose, unusual stucco molding is used. The upper part can be decorated with plaster bas-relief.

More modern arches have a fairly simple design, but can have fancy shapes.

In this case they are different unusual lines and intricate patterns.

Some nuances

When choosing a design, you need to consider some rules. The decor of a wide and narrow doorway should be different. For wide ones, more prominent and larger ones are usually selected. decorative elements, and narrow openings are decorated with simple finishing materials. It is better to use light decorative elements for this.

A high doorway is often designed in the form of an arch. It can add luxury and elegance to the interior of a home. It is not customary to decorate a deep doorway with arches, since then the structure will look very massive. But in this case, an arch model with large columns is suitable.

If your goal is not to unite different rooms, but to differentiate them, then compartment doors are perfect for this. They separate well functional areas and look very stylish. Most often they are used to decorate rooms in modern styles.

When choosing material for cladding, it is necessary to pay attention to the quality of finishing materials. Many are inexpensive plastic panels are very environmentally unfriendly and can even emit harmful substances. Therefore, try to give preference only to high-quality materials.

Polyurethane Decoration Materials should not be installed at the entrance to the kitchen. This is due to the fact that they have low heat resistance. To design such a doorway, you should choose materials that are more resistant to elevated temperatures.

If you want to dismantle the door frame for finishing, you should take into account that this may lead to cracks in the wall. That is why, before dismantling it, it is necessary to install a power frame.

This way you can carry out correct design and, after that, decorate the doorway.

Return